Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fast ignition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Finite-rate entrainment effects on nitrogen oxide (NO x ) emissions in staged combustors

Axially staged combustors offer the potential for achieving low NO x emissions from gas turbines at the elevated temperatures required to achieve at least 65% combined cycle efficiencies. While there is evidence that premixing between the main burner products and secondary stream reduces NO x , it is important to characterize the specific requirements needed to achieve low emissions at gas turbine conditions. This study examines the sensitivity of NO x to finite-rate, large-scale entrainment of the main and secondary streams under the simplifying assumption of infinitely-fast small-scale mixing. Essentially, this allows us to isolate the effects of limited large-scale entrainment rates by using a homogeneous/uniform condition for the entrained and reacting gases. We use a reduced-order reactor network model to examine a generic staged-combustor whose inputs are physical time scales that embody the finite-rate entrainment characteristics. With simulations conducted over a large parameter space at typical operating conditions (25 atm, 650 K air), the results show that, even when small-scale mixing is infinitely fast and the reaction zone is uniform, entrainment significantly affects NO x emissions due to its influence on the equivalence ratio — and thus the temperature and time — at which the entrained mixture ignites. Fuel-air staging is shown to be vital to NO x reduction in most practical cases where entrainment times exceed roughly 1 ms and the secondary stream finishes entraining before the main burner products. A constrained NO x minimization indicates that using the leanest possible main burner and re-routing as much air as possible to the secondary stage is key to low NO x with finite-rate entrainment; for example, less than 10 ppm NO x can be achieved if the secondary stage contains 20% of the total mass flow.

03 NATURAL GAS↗
DOE OSTI2026

Time-dependent-bases with local CUR decomposition method for accelerating turbulent combustion simulations

Here, this study presents a novel reduced-order modeling framework, Time-Dependent Bases with Local CUR decomposition (TDB-L-CUR), designed to efficiently and accurately approximate the species transport equations in reacting flow simulations. The method extends the existing TDB-CUR approach for chemically reacting flows (Jung et al. Comput. Methods Appl. Mech. Engrg. 437 (2025) 117758), which leverages matrix decomposition techniques to form a global-in-space, time-dependent low-dimensional manifold. While TDB-CUR performs well in homogeneous systems, it may be less well-suited to spatially heterogeneous systems such as turbulent flames, where higher-rank approximations are typically required. The proposed TDB-L-CUR framework introduces two methodological extensions to the baseline approach. First, it applies unsupervised clustering to partition the physical domain into distinct regions, enabling spatially localized manifold construction, thereby reducing the rank required for the reduced-order representation. Second, it incorporates a computational singular perturbation (CSP)-based scheme for identifying and penalizing fast species, allowing for spatio-temporally adaptive mitigation of chemical stiffness. The proposed framework is validated on a hierarchy of test cases, including a one-dimensional premixed flame, a two-dimensional nonpremixed ignition case with vortex interaction, and a three-dimensional turbulent premixed flame. TDB-L-CUR significantly improves accuracy over TDB-CUR while further reducing computational cost. The fully on-the-fly formulation of TDB-L-CUR (i.e., requiring no offline training or prior knowledge) makes it a robust and scalable tool for reduced-order modeling of reactive flows.

Local manifold↗
DOE OSTI2023

Hierarchical multi-time-scale predictive thermal management and fuel optimization for heavy-duty compression ignition engines

For heavy-duty diesel engines, NO X emissions reduction is strongly constrained by fuel efficiency. This paper presents a hierarchical model predictive controller (H-MPC) for coordinated control of tailpipe NO X emissions and fuel consumption. The H-MPC uses the separation of slow and fast dynamics that exist in the engine and its aftertreatment system. The controller is synthesized with an architecture in which a high-level MPC uses a longer prediction horizon compared to the low-level predictive controller which tracks the high-level controller command and manages the thermal dynamics of the aftertreatment system. Engine load preview enables the high-level controller to estimate the desired catalyst temperature ahead of time and addresses the selective catalytic reduction (SCR) slow thermal dynamics. Calculated by the high-level controller, the intake manifold pressure, and the start of injection (SOI) crank angle is used as reference trajectories in the low-level controller that regulates fast dynamical behaviors such as engine out NO X emissions. Hardware-in-the-loop (HIL) validation of this integrated H-MPC on a rapid prototype controller shows that when the SCR catalyst temperature is above light-off temperature (warmed-up condition), the engine operation is shifted to operate with the best fuel economy since the warmed-up SCR can efficiently reduce the engine-out NO X emissions. Results indicate that up to 0.8% benefit in cycle averaged BSFC along with a 13% reduction in tailpipe NO X compared to a stock engine calibration can be achieved with the coordinated engine and aftertreatment system through H-MPC.

Engineering↗
DOE OSTI2020

Data for “Lightning Interferometry Uncertainty, “Focused Interferometry”, and Evidence of Lightning being Ignited by a Cosmic-ray Shower” by Shao et al.

This summarizes the data from our broadband RF interferometric mapping and polarization (BIMAP) system used to produce the figures in the revised manuscript “Lightning Interferometry Uncertainty, “Focused Interferometry”, and Evidence of Lightning being Ignited by a Cosmic-ray Shower” that was originally submitted to Journal of Geophysical Research (JGR) for publication. Note that the original manuscript was titled ““Focused Interferometry” and Fine Structure of Lightning-Initiating Fast Positive Streamers” and was released with LA-UR-19-32549. In accordance with JGR’s data policy (https://www.agu.org/Publish-withAGU/Publish/Author-Resources/Policies/Data-policy), it is the intention to make this data publicly available at the time of article submission. The data set includes raw BIMAP RF data and processed results for two lightning flashes. The data is available in two files (“FPS_data_20170606_361.sav” and “Small_IC_20180520_205644_408.sav”) located at “/home/xshao/HEPL/Analysis” which were packaged with IDL save commend. The raw data includes 3 channels of RF data, 2 channels of RF polarization data, and 1 channel of electric field change data. The processed data includes the RF source positions, source position uncertainties, and the polarization analysis.

58 GEOSCIENCES↗
DOE OSTI2023

Evaluation of Spray and Combustion Models for Simulating Dilute Combustion in a Direct-Injection Spark-Ignition Engine

Dilute combustion in spark-ignition engines has the potential to improve thermal efficiency by mitigating knock and by reducing throttling and wall heat losses. However, ignition and combustion processes can become unstable for dilute operation due to a lowered laminar flame speed, resulting in excessive cycle-to-cycle variability (CCV) of the combustion process. To compensate for the slower combustion in less reactive mixtures, a modified intake port geometry can be employed to generate a strong tumble flow in the cylinder and elevate turbulence levels around the spark plug, thereby promoting a faster transition to turbulent deflagration. Consequently, optimizing combustion chamber geometry and operating strategy is crucial to maximizing the benefits of using dilute combustion with enhanced in-cylinder turbulence across a wide range of operating conditions. Computational fluid dynamics (CFD) simulations can be utilized for virtual engine optimization tasks, but this would require the models to be truly predictive regarding the impact of changes to the engine design and operational parameters.In this study, multicycle large-eddy simulations (LES) are performed for a direct-injection spark-ignition engine to investigate the model performance in predicting engine combustion characteristics with respect to changes in the intake configuration. A tumble plate that blocks the lower part of the intake port inlet is used to vary the tumble. A set of CFD models that have been recently developed are employed, which takes into account the drag of nonspherical droplets, flash-boiling behavior of liquid sprays, spray-wall interaction, surrogate formulation of a research-grade E10 gasoline, and fast chemical kinetic solvers. Simulation results are compared to experimental engine data in terms of cylinder pressure, apparent heat release rate, mass fraction burned timing, and flame images. It is found that LES employing the state-of-the-art CFD models are capable of properly predicting the spray processes and reproducing the measured mean cylinder pressure for the case with the tumble plate. On the other hand, the LES over-predicts the combustion rate during the early combustion stage and under-estimates the CCV, and these discrepancies become larger when the tumble plate is removed.

computational fluid dynamics simulation↗
DOE OSTI2024

Bioblendstocks to Optimize Mixing Controlled Compression Ignition (MCCI) Engines

In this project, a team of researchers from the University of Massachusetts Lowell, the University of Maine, and Mainstream Engineering developed an integrated process for the product of bioblendstocks to optimize mixing controlled compression ignition (MCCI) engines. The objective was to improve the energy density, sooting propensity, and cetane number of base diesel fuel while maintaining cold weather behavior. The process converts woody biomass (e.g. sawmill residues) into bio-oil through selective fast pyrolysis; the bio-oil is then selectively upgraded to form selectively oxygenated, minimally-branched hydrocarbons using non-noble metal catalysts in combination with metal-catalyzed hydrogenation. Advanced predictive models, in conjunction with existing property databases, and experimental testing are used to evaluate overall bioblendstock properties and their impact on base diesel fuel. An iterative, targeted upgrading approach was implemented to optimize the proposed bioblendstock’s properties. Assessment methodologies included techno-economic analysis, life-cycle assessment, property testing, and engine testing. Ultimately, the project team successfully produced a viable bioblendstock while identifying critical process points related to scale-up efforts. It was found that producing pyrolysis oils at 500 degrees C and with pine particle sizes of 1-2 mm led to bio-oil with a higher yield (of approximately 45 wt%) and rich amounts of aromatic alcohols. The resultant pyrolysis oil was then upgraded using a sequence of mild hydrotreating, followed by catalytic etherification and esterification, followed by another final mild hydrotreating to produce a blendstock containing saturated species with a limited, but non-zero, amount of oxygen. The aromatic alcohols produced by pyrolysis were especially helpful in this regard, as the resulting bicycloethers and derivatives exhibited high cetane numbers. While most bulk properties of the bioblendstock met or exceeded targeted thresholds, viscosity and cloud point notably fell outside the expected range; this could be addressed by blending limits and/or through the use of additives that are commonplace in current refinding practices. Identification of a bioblendstock that can be produced economically at scale while improving the performance and emissions characteristics of internal combustion engines positively affects the economy by boosting domestic fuel production and the environment by decreasing harmful emissions and increasing efficiency.

09 BIOMASS FUELS↗
DOE OSTI2022

INVESTIGATION OF TURBULENT JETS, SPRAYS, AND SUPERCRITICAL MIXING BY TIME RESOLVED RAINBOW SCHLIEREN DEFLECTOMETRY

As technological advancements have enabled higher efficiency compression ignition (CI) engines (diesel engines) by operating at higher pressures and temperatures, the mechanisms of fuel-air mixing are postulated to change. Thus, there is a greater need for experimental data to develop and verify new phenomena. However, the fast time scales and harsh environments associated with CI engines present many experimental difficulties and requires high quality non-intrusive diagnostics to obtain useful data. The diagnostics itself must be validated prior to its implementation in an engine environment. The purpose of this research is to advance rainbow schlieren deflectometry (RSD) to study turbulent fuel sprays including the effects of supercritical mixing in CI engine environments. This objective is met by developing and applying quantitative RSD, for the first time, to three separate aspects of fuel sprays: 1) turbulent mixing, 2) phase boundaries, and 3) non-ideal gas mixing. First, quantitative RSD is demonstrated for turbulent mixing in a canonical helium jet. Rayleigh scattering data in the literature is used to validate the concentration measurements obtained by RSD. The results also provide explanations for phenomena occurring in the helium jet and provide data not yet present in the literature. Second, RSD is applied to high pressure multi-phase fuel sprays and new methodologies are developed to distinguish the liquid region from the vapor region and to quantify the in-between region on a probabilistic basis. Isolating liquid and vapor regions generally requires two separate diagnostics, e.g., Mie scattering (liquid region) and Rayleigh scattering (vapor region). However, the results of this study demonstrate that RSD can be used as a single diagnostic to measure both liquid and vapor boundaries. Third, the optical-to-thermodynamic relations associated with refrac-tometry are investigated under non-ideal gas mixing conditions to develop a generalized relationship valid for both ideal or non-ideal gas mixing. The last part of this research develops the theoretical tools to understand and experimentally realize supercritical mixing at diesel conditions. Guided by the theoretical analysis, RSD is applied to compare supercritical versus transcritical mixing at CI conditions using a constant pressure test rig. It is found that while fully supercritical mixing ers benefits in diesel engines, i.e, faster mixing times (50% higher velocities), the absence of droplets which cause high levels of particulate emissions, etc., it would be difficult to achieve in practice because of the requirements of fuels with low critical temperature and/or substantial fuel preheating.

02 PETROLEUM↗
DOE OSTI2024

Diagnostic development and needs for laser driven MeV x-ray radiography

Laser-driven MeV x-ray radiography of dynamic, dense objects demands a small, high flux source of energetic x-rays to generate an image with sufficient quality. Understanding the multi-MeV x-ray spectrum underscores the ability to extrapolate from the current laser sources to new future lasers that might deploy this radiography modality. Here, in this study, we present a small study of the existing x-ray diagnostics and techniques. We also present work from National Ignition Facility-Advanced Radiographic Capability, where we deploy three diagnostics to measure the x-ray spectrum up to 30 MeV. Finally, we also discuss the needs and developments of two new diagnostics: a single crystal scintillator spectrometer and a fast decay activation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Modeling of thermal and kinetic processes in non-equilibrium plasma ignition applied to a lean combustion engine

In recent years novel ignition systems have been developed to enable stable and efficient engine operations with lean mixtures. Among them, radio-frequency corona ignition systems create discharges that involve a much wider region compared to traditional spark, and produce non equilibrium plasma with high levels of active radicals and excited species. These devices considerably increase the early flame growth speed and extend stable operating limits. With the aim of expanding the knowledge on high efficiency lean-burn SI engines, this paper investigates and compares the combustion development generated by spark and corona ignitions through computational fluid dynamics, within the Reynolds-Averaged Navier-Stokes framework for turbulence modeling. In order to simultaneously take thermal and chemical effects into account, the Perfectly Stirred Reactor combustion model is used. Experimental data are also collected for validation in an optical access engine, for different mixture levels, from stoichiometric to very lean. Furthermore, the faster burn rate generated by the corona system in the initial stage of the combustion is well predicted by the simulations, in all the relative air-fuel ratio conditions. Remarkably, as the mixture becomes lean, simulations are able to capture the non-linear transition from fast to slow kernel growth, before a self-sustainable flame propagation is established. This correlates very well with the measured engine cyclic variability and the corresponding steep change in the duration of the flame kernel formation. Ultimately, this study highlights the important role of the atomic oxygen, as active radical, in promoting and enhancing the combustion initiated by a corona discharge, in addition to the volumetric ignition effect. By contrast, the validated simulations allow to explain that the high-temperature thermal plasma generated in a traditional spark discharge is insensitive to kinetic aspects.

42 ENGINEERING↗
DOE OSTI2021

Proof-of-concept of a neutron time-of-flight ellipsoidal detector

The time-resolved measurement of neutrons emitted from nuclear implosions at inertial confinement fusion facilities is used to characterize the fusing plasma. Several significant quantities are routinely measured by neutron time-of-flight (nToF) detectors in these experiments. Current nToF detectors use scintillators as well as solid-state Cherenkov radiators. The latter has an inherently faster time response and can provide a co-registered γ-ray measurement as well as improved precision in the bulk hot-spot velocity. This work discusses a nToF ellipsoidal detector that also utilizes a solid-state Cherenkov radiator. The detector has the potential to achieve a fast instrument response function allowing for characterization of the γ-ray burn history as well as the ability to field the detector closer to the fusion source. Proof-of-concept testing of the nToF ellipsoidal detector has been conducted at the National Ignition Facility using commercial optics. A time-resolved neutron signal has been measured from the diagnostic. Preliminary simulations corroborate the results.

Jeet, J. (ORCID:0000000291091563)↗
DOE OSTI2024

Inferring fusion nuclear burnwidths with low gain photomultiplier impulse response functions

When an inertial confinement fusion implosion is compressed, it maintains thermonuclear density and temperatures for a very short time scale, about 100 ps. The Gamma Reaction History diagnostic measures the time evolution of the fusion burn, but its temporal resolution is limited by the use of a photomultiplier tube (PMT) to amplify the photon signal. Multichannel plate-based PMTs have a fast (~120 ps) full-width at half-max impulse response function (IRF), but the time scale is similar to the incoming physics signal. An analysis routine is used to remove the effect of the PMT IRF and infer the incident fusion burnwidth. With the National Ignition Facility achieving ignition and creating much brighter signals, the PMTs are run at gains three orders of magnitude lower than nominal operation. Calibration at these settings shows the PMT IRFs get ~15% wider. Taking the gain-dependent IRF can affect the inferred nuclear burnwidths by up to ~15%.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Experimental Characterization of Hydrocarbons and Nitrogen Oxides Production in a Heavy-Duty Diesel–Natural Gas Reactivity-Controlled Compression Ignition Engine

Reactivity-Controlled Compression Ignition (RCCI) combustion is considered one of the most promising Low-Temperature Combustion (LTC) concepts aimed at reducing greenhouse gases for the transportation and power generation sectors. Due to the spontaneous combustion of a lean, nearly homogeneous mixture of air and low-reactivity fuel (LRF), ignited through the direct injection of a small quantity of high-reactivity fuel (HRF), RCCI (dual-fuel) shows higher efficiency and lower pollutants compared to conventional diesel combustion (CDC) if run at very advanced injection timing. Even though a HRF is used, the use of advanced injection timing leads to high ignition delays, compared to CDC, and generates high cycle-to-cycle variability, limited operating range, and high pressure rise rates at high loads. This work presents an experimental analysis performed on a heavy-duty single-cylinder compression ignited engine in dual-fuel diesel–natural gas mode. The objective of the present work is to investigate and highlight the correlations between combustion behavior and pollutant emissions, especially unburned hydrocarbons (HC) and oxides of nitrogen (NOx). Based on the analysis of crank-resolved pollutants measurements performed through fast FID and fast NOx systems under different engine operating conditions, two correlations were found demonstrating a good accordance between pollutant production and combustion behavior: Net Cyclic Hydrocarbon emission—cyclic IMEP variations (R 2 = 0.86), and Cyclic NOx—maximum value of the Rate of Heat Released (R 2 = 0.82).

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Nanosecond Gated CMOS Camera (NSGCC) ICD (Rev. 2.1)

The Ultra-Fast X-ray Imager (UXI) program is an ongoing effort at Sandia National Laboratories to create high speed, multi-frame, time-gated Read Out Integrated Circuits (ROICs), and a corresponding suite of photodetectors to image a wide variety of High Energy Density (HED) physics experiments on both Sandia’s Z-Machine and LLNL’s National Ignition Facility (NIF). Several cameras have been designed over the length of the program; one of the most recent is the Icarus, which is an improvement on past imagers (Furi and Hippogriff). A second sensor that can be connected is the Daedalus sensor. The Icarus is a 1024 × 512-pixel array with either 25 μm or 8 µm spatial resolution containing four frames of storage per pixel and has improved timing generation and distribution components while achieved 2 ns time gating. The Daedalus sensor is also a 1024 x 512-pixel array with 25 µm special resolution containing three frames of storage per pixel and has an increased set of features for a wider variety of applications from interlacing of rows in each frame to configurability of all shutters. See Section 14 for details regarding the Icarus implementation of the firmware and Section 15 for details regarding the Daedalus implementation. Due to the unique test environments UXI sensors are targeted for, full custom hardware was required to physically mount an Icarus or Daedalus sensor, manage its various functions, and read out pixel data for transfer to a host computer. Beyond experimental functionality, the hardware also needed to accommodate sensor characterization requirements. Lawrence Livermore National Laboratory’s ‘Version 4.0 Board’ was the result of these efforts. It mounts all the components required to fully utilize the Icarus and Daedalus sensors including analog to digital converters to convert pixel data and various system voltages to digital form for readout and analysis, DAC channels for remote configuration of critical bias voltages, static random-access memories to buffer pixel data, RS422 and Gigabit Ethernet communications for remote access, and an FPGA to tie these components together. This document describes the FPGA electrical interfaces in detail to allow the reader a greater understanding of the device, and to facilitate implementation of custom software to control and manage it. The Version 4.0 Board is a continuation of the Nano-second Gated CMOS hardware design that retains much of the functionality of the Version 1.0 Board while adding features including a DAC instead of digital potentiometers, as well as sensors for pressure and radiation. The Version 4.0 board is intended for applications requiring tight form-factor enclosures. It is composed of two stacking boards; one holds the FPGA and regulators to power the various components of the board while the other contains the mating connector to the sensor, image-readoff ADCs, the DAC, and other components.

42 ENGINEERING↗
DOE OSTI2024

Lowering the reactor breakeven requirements for proton–boron 11 fusion

Recently, it has been shown that altering the natural collisional power flow of the proton–boron 11 (pB11) fusion reaction can significantly reduce the Lawson product of ion density and confinement time required to achieve ignition. However, these products are still onerous—on the order of 7×1015 cm−3 s under the most optimistic scenarios. Fortunately, a breakeven fusion power plant does not require an igniting plasma, but rather a reactor that produces more electrical power than it consumes. Here, we extend the existing 0D power balance analysis to check the conditions on power plant breakeven. We find that even for the base thermonuclear reaction, modern high-efficiency thermal engines should reduce the Lawson product to 1.2×1015 cm−3 s. We then explore the impact of several potential improvements, including fast proton heating, alpha power capture, direct conversion, and efficient heating. We find that such improvements could reduce the required Lawson product by a further order of magnitude, bringing aneutronic fusion to target ITER ion densities and confinement times.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

FASTSim™ (Future Automotive Systems Technology Simulator) [SWR-20-101 and SWR-12-07]

The Future Automotive Systems Technology Simulator (FASTSim™) provides a simple way to compare powertrains and estimate the impact of technology improvements on light-, medium-, and heavy-duty vehicle efficiency, performance, cost, and battery life. This extremely fast simulation tool features a streamlined user interface and can rapidly perform a variety of tasks using basic computing resources: • less than 0.1 second to simulate second-by-second standard duty cycles • less than 10 seconds to estimate vehicle efficiency, fuel economy, acceleration, battery life, and cost • less than 5 minutes to perform powertrain comparisons of efficiency and cost. FASTSim models a variety of vehicle powertrains and fuel converter types: • Conventional vehicles - spark ignition, Atkinson, diesel, and hybrid diesel • Electric-drive vehicles - hybrid, plug-in hybrid, and all-electric • Hydrogen fuel cell vehicles. The default model includes a variety of vehicles and duty cycles and an option for adding additional vehicles and custom cycles: • Packaged with more than 20 vehicles • User interface enables addition of more vehicles • Includes standard U.S. drive cycles as well as European and Japanese cycles. FASTSim is available for download in Microsoft Excel and Python formats here: https://www.nrel.gov/transportation/fastsim.html

Baker, Chad↗
DOE OSTI2025

Unveiling the thermite-driven lithium fire ignition in solid-state batteries

Here, this study challenges the assumption of the non-flammability of lithium metal all-solid-state batteries (LiSSBs) and other lithium metal batteries without flammable electrolytes. Through thermodynamic calculations and ex situ experiments, we reveal for the first time the risk of thermite reactions between lithium metal and LiFePO 4 in both charged and discharged states. Reactivity is worsened by excess lithium metal in the cell, reaching final maximum adiabatic temperatures of 2,500°C in the charged state, which is hot enough to boil lithium. The thermite reaction triggers spontaneously at 500°C, with poor surface contact, while increasing surface contact through mixing initiates the reaction at room temperature in an inert environment. Despite its fast kinetics, this reaction is transport limited due to lithium passivation, leading to long burn times and reignition risks. Given the risk of lithium metal contacting the cathode during failure, understanding these reactions is crucial for ensuring the safe deployment of LiSSBs.

LiFePO4↗
DOE OSTI2025

Investigating performance and variability of NIF ICF experiments with deep learning

The parameter space involved in designing an inertial confinement fusion shot at the National Ignition Facility (NIF) is massively multi-dimensional and the cost of a single shot makes a comprehensive set of sensitivity studies in the laboratory impractical. The use of machine learning to overcome these challenges has gained popularity and has had several successful applications by the scientific community. We extend on these efforts by training a neural network (NN) on information about the experimental design, engineering elements, and drive asymmetry to predict with uncertainty the neutron yield of an experiment. We find the measured and model predicted values are in good agreement, with an R 2 value of 0.91 for a randomly selected test dataset. Almost all the predicted 95% credible intervals contain the corresponding measured value for both training and test datasets. We identify correlations picked up by the NN between the shot design, yield, and variability and use them to motivate shot sensitivity studies. The first shot to exceed the Lawson-like ignition criteria (N210808) was conducted at the NIF and subsequent shots studied the design’s robustness. In a follow-up shot to N210808, our model predicts capsule quality to be the main performance degradation mechanism that prevented the shot from repeating previous performance levels. Shot N221204 was the first shot to exceed a target energy gain of 1. Our model predicts increased yield with reduced coast time for a N221204 study and greater variability for designs with lower peak powers at constant yield. The model’s fast prediction speed and uncertainty prediction are useful for identifying interesting design paths that could warrant further investigation with conventional simulations to search for robust high yield designs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Design of a High-Pressure Fuel System for Use with Dimethyl Ether

The paper documents the modeling and experimental work on a common rail fuel injection system for Dimethyl Ether, a potential diesel substitute with a low carbon intensity signature. The DME fuel system is deployed on a light duty 2.2L compression ignition engine. The paper describes the injector optimization to shift to higher flows to account for the lower heating value and density of the DME when compared to diesel. The type of the injection system used for the DME application is an advanced rendering of the Common rail noted for a one-piece piston-needle injector construction and a solenoid driven spill valve featuring a pressure balanced poppet. A dedicated high-pressure fuel pump designed to pressurize DME is used. The design results in a fast acting open and close injection event, reduced leakage, with reduced cavitation in the fuel injector volume. Design parameters for system optimization included fill and spill orifices, needle lift, bias spring, and injector hole size. The design model provides good correlation of the instantaneous rates of injection with experiments across a wide range of pressure and injection timings. Proposed performance milestones for the design included similar DME injection duration to the diesel counterpart for same fuel energy injected into the cylinder to retain high engine cycle efficiency. Here, the dedicated DME design provided reduced hydraulic delays of 50%. Tests demonstrated sustained operation at pressures of 1000 bar, with capability to reach 1500bar. Durability tests showed no cavitation-deterioration over a 200-hour test cycle by means of spray imaging and hardware inspection.

De Ojeda, William [WM International Engineering, L↗