Search NASA⌕ Search

SEARCH · Search NASA

Results for “Flame speed”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

An experimental and detailed kinetic modeling study of the pyrolysis and oxidation of allene and propyne over a wide range of conditions

Allene and propyne are important intermediates in the pyrolysis and oxidation of higher hydrocarbon fuels, and they are also a major source of propargyl radical formation, which can recombine into different C 6 H 6 isomers and finally produce soot. In a prior work (Panigrahy et al., “A comprehensive experimental and improved kinetic modeling study on the pyrolysis and oxidation of propyne”, Proc. Combust. Inst 38 (2021)), the pyrolysis, ignition , and laminar flame speed of propyne were investigated. To understand the kinetic features of initial fuel breakdown and oxidation of the two C 3 H 4 isomers, new measurements for allene pyrolysis and oxidation are conducted in the present paper at the same operating conditions as those studied previously for propyne. Ignition delay times of allene are measured using a high-pressure shock tube and a heated twin-opposed piston rapid compression machine in the temperature range 690– 1450 K at equivalence ratios of 0.5, 1.0 and 2.0 in ‘air’, and at pressures of 10 and 30 bar. Pyrolysis species measurements of allene and propyne are also performed using a gas chromatography integrated singlepulse shock tube in the temperature range 1000–1700 K at pressure of 2 and 5 bar. Furthermore, laminar flame speeds of allene are measured at elevated gas temperatures of 373 K at pressures of 1 and 2 bar for a wide range of equivalence ratios from 0.6 to 1.5. A newly updated kinetic mechanism developed for this study is the first model that can well reproduce all of the experimental results for both allene and propyne. It is observed that in the pyrolysis process, allene dissociates faster than propyne. Both isomers exhibit similar ignition delay times at high temperatures (>1000 K), while, at intermediate temperatures (770–1000 K) propyne is the faster to ignite, and at lower temperatures (< 770 K) allene becomes more reactive. Furthermore, laminar flame speeds for propyne are found to be slightly faster than those for allene under the conditions studied in this work

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Numerical Investigation of a Central Fuel Property Hypothesis under Boosted Spark-ignition Conditions

In the present work, a central fuel property hypothesis (CFPH), which states that fuel properties are sufficient to provide an indication of a fuel's performance irrespective of its chemical composition, was numerically investigated In particular, the objective of the study was to determine whether Research Octane Number (RON) and Motor Octane Number (MON), as fuel properties, are sufficient to describe a fuel's knock-limited performance under boosted spark-ignition (SI) conditions within the framework of CFPH. To this end, four TPRF-bioblendstock surrogates having different compositions but matched RON (= 98) and MON (= 90), were first generated using a non-linear regression model based on artificial neural network (ANN). Three unconventional bioblendstocks were included in the analysis: Di-isobutylene (DIB), Isobutanol and Anisole. Skeletal reaction mechanisms were generated for the TPRF-DIB, TPRF-isobutanol and TPRF-anisole blends from a detailed kinetic mechanism. Thereafter, numerical simulations were performed for the fuel surrogates using the skeletal mechanisms and a virtual cooperative fuel research (CFR) engine model, under a representative boosted operating condition. In the computational fluid dynamics (CFD) model, the G-equation approach was employed to track the turbulent flame front and the well-stirred reactor model combined with multi-zone binning strategy was used to capture auto-ignition in the end-gas. In addition, laminar flame speed was tabulated for each blend as a function of pressure, temperature and equivalence ratio a priori, and the lookup tables were used to prescribe laminar flame speed as an input to the G-equation model. Parametric spark timing sweeps were performed for each fuel blend to determine the corresponding knock-limited spark advance (KLSA) and 50% burn point (CA50) at the respective KLSA timing. It was observed that despite same RON, MON and engine operating conditions, the TPRF-Anisole blend exhibited markedly different knock-limited performance from the other three blends. This deviation from the octane index (DI) expectation was shown to be caused by differences in laminar flame speed (LFS). However; it was found that relatively large fuel-specific differences in LFS (> 20%) would have to be present to cause any appreciable deviation from the 01 framework. Otherwise, RON and MON would still be robust enough to predict a fuel's knock-limited performance.

Pal, Pinaki↗
NASA NTRS1937

Some effects of argon and helium upon explosions of carbon monoxide and oxygen

Report presents the results of an investigation conducted to study the effects of the inert gases, argon and helium, upon flame speed and expansion ratio in exploding mixtures of carbon monoxide, oxygen and water.For the particular gas mixtures investigated the results show that: (1) With the possible exception of helium in small amounts the addition of inert gas always produces decreased flame speed and expansion ratio; (2) like volumes of argon and helium have very different effects upon flame speed but practically the same effect upon expansion ratio; and (3) the difference in the effect of these two gases upon speed is independent of the ratio of carbon monoxide to oxygen. A discussion of some possible modes by which inert gases may produce the observed effects is included.

Fiock, Ernst F↗
DOE OSTI2020

Numerical Investigation of a Central Fuel Property Hypothesis Under Boosted Spark-Ignition Conditions

In the present work, a central fuel property hypothesis (CFPH), which states that fuel properties are sufficient to provide an indication of a fuel’s performance irrespective of its chemical composition, was numerically investigated. In particular, the objective of the study was to determine whether Research Octane Number (RON) and Motor Octane Number (MON), as fuel properties, are sufficient to describe a fuel’s knock-limited performance under boosted spark-ignition (SI) conditions within the framework of CFPH. To this end, four TPRF-bioblendstock surrogates having different compositions but matched RON (=98) and MON (=90), were first generated using a non-linear regression model based on artificial neural network (ANN). Additionally, three unconventional bioblendstocks were included in the analysis: di-isobutylene (DIB), isobutanol, and Anisole. Skeletal reaction mechanisms were generated for the TPRF-DIB, TPRF-isobutanol, and TPRF-anisole blends from a detailed kinetic mechanism. Thereafter, numerical simulations were performed for the fuel surrogates using the skeletal mechanisms and a virtual cooperative fuel research (CFR) engine model, under a representative boosted operating condition. In the computational fluid dynamics (CFD) model, the G-equation approach was employed to track the turbulent flame front and the well-stirred reactor model combined with the multi-zone binning strategy was used to capture auto-ignition in the end-gas. In addition, laminar flame speed (LFS) was tabulated for each blend as a function of pressure, temperature, and equivalence ratio a priori, and the lookup tables were used to prescribe laminar flame speed as an input to the G-equation model. Parametric spark timing sweeps were performed for each fuel blend to determine the corresponding knock-limited spark advance (KLSA) and 50% burn point (CA50) at the respective KLSA timing. It was observed that despite same RON, MON, and engine operating conditions, the TPRF-anisole blend exhibited markedly different knock-limited performance from the other three blends. This deviation from the octane index (OI) expectation was shown to be caused by differences in laminar flame speed. However, it was found that relatively large fuel-specific differences in LFS (>20%) would have to be present to cause any appreciable deviation from the OI framework. Otherwise, RON and MON would still be robust enough to predict a fuel’s knock-limited performance.

42 ENGINEERING↗
NASA NTRS1996

Turbulent flame propagation in partially premixed flames

Turbulent premixed flame propagation is essential in many practical devices. In the past, fundamental and modeling studies of propagating flames have generally focused on turbulent flame propagation in mixtures of homogeneous composition, i.e. a mixture where the fuel-oxidizer mass ratio, or equivalence ratio, is uniform. This situation corresponds to the ideal case of perfect premixing between fuel and oxidizer. In practical situations, however, deviations from this ideal case occur frequently. In stratified reciprocating engines, fuel injection and large-scale flow motions are fine-tuned to create a mean gradient of equivalence ratio in the combustion chamber which provides additional control on combustion performance. In aircraft engines, combustion occurs with fuel and secondary air injected at various locations resulting in a nonuniform equivalence ratio. In both examples, mean values of the equivalence ratio can exhibit strong spatial and temporal variations. These variations in mixture composition are particularly significant in engines that use direct fuel injection into the combustion chamber. In this case, the liquid fuel does not always completely vaporize and mix before combustion occurs, resulting in persistent rich and lean pockets into which the turbulent flame propagates. From a practical point of view, there are several basic and important issues regarding partially premixed combustion that need to be resolved. Two such issues are how reactant composition inhomogeneities affect the laminar and turbulent flame speeds, and how the burnt gas temperature varies as a function of these inhomogeneities. Knowledge of the flame speed is critical in optimizing combustion performance, and the minimization of pollutant emissions relies heavily on the temperature in the burnt gases. Another application of partially premixed combustion is found in the field of active control of turbulent combustion. One possible technique of active control consists of pulsating the fuel flow rate and thereby modulating the equivalence ratio (Bloxsidge et al. 1987). Models of partially premixed combustion would be extremely useful in addressing all these questions related to practical systems. Unfortunately, the lack of a fundamental understanding regarding partially premixed combustion has resulted in an absence of models which accurately capture the complex nature of these flames. Previous work on partially premixed combustion has focused primarily on laminar triple flames. Triple flames correspond to an extreme case where fuel and oxidizer are initially totally separated (Veynante et al. 1994 and Ruetsch et al. 1995). These flames have a nontrivial propagation speed and are believed to be a key element in the stabilization process of jet diffusion flames. Different theories have also been proposed in the literature to describe a turbulent flame propagating in a mixture with variable equivalence ratio (Muller et al. 1994), but few validations are available. The objective of the present study is to provide basic information on the effects of partial premixing in turbulent combustion. In the following, we use direct numerical simulations to study laminar and turbulent flame propagation with variable equivalence ratio.

Poinsot, T.↗
DOE OSTI2023

A wide range experimental and kinetic modeling study of the oxidation of 2,3-dimethyl-2-butene: Part 1

2,3-Dimethyl-2-butene (TME) is a potential fuel additive with high research octane number (RON) and octane sensitivity (S), which can improve internal combustion engine performance and efficiency. However, the combustion characteristics of TME have not been comprehensively investigated. Thus, it is essential to study the combustion characteristics of TME and construct a detailed chemical kinetic model to describe its combustion. In this paper, two high-pressure shock tubes and a constant-volume reactor are used to measure ignition delay times and laminar flame speeds of TME oxidation. Further, the ignition delay times were measured at equivalence ratios of 0.5, 1.0, and 2.0 in “air”, at pressures of 5 and 10 bar, in the temperature range of 950 – 1500 K. Flame speeds of the TME/ “air” mixtures were measured at atmospheric pressure, at a temperature of 325 K, for equivalence ratios ranging from 0.78 to 1.31. Two detailed kinetic mechanisms were constructed independently using different methodologies; the KAUST TME mechanism was constructed based on NUIGMech1.1, and the MIT TME mechanism was built using the Reaction Mechanism Generator (RMG). Both mechanisms were used to simulate the experimental results using Chemkin Pro. In the present work, reaction flux and sensitivity analyses were performed using the KAUST mechanism to determine the critical reactions controlling TME oxidation at the conditions studied.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Skeletal reaction models for methane combustion

A local-sensitivity-analysis technique is employed to generate new skeletal reaction models for methane combustion from the foundational fuel chemistry model (FFCM-1). Here, the sensitivities of the thermo-chemical variables with respect to the reaction rates are computed via the forced-optimally time dependent (f-OTD) methodology. In this methodology, the large sensitivity matrix containing all local sensitivities is modeled as a product of two low-rank time-dependent matrices. The evolution equations of these matrices are derived from the governing equations of the system. The modeled sensitivities are computed for the auto-ignition of methane at atmospheric and high pressures with different sets of initial temperatures, and equivalence ratios. These sensitivities are then analyzed to rank the most important (sensitive) species. A series of skeletal models with different number of species and levels of accuracy in reproducing the FFCM-1 results are suggested. The performances of the generated models are compared against FFCM-1 in predicting the ignition delay, the laminar flame speed, and the flame extinction. The results of this comparative assessment suggest the skeletal models with 24 and more species generate the FFCM-1 results with an excellent accuracy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1977

Model for premixed turbulent flames

Flame speed and mean degree of reaction profiles are determined for an ensemble mean one-dimensional premixed turbulent flame. Elementary closure models are employed to treat turbulence closure problems arising from the nonlinear convective and chemical reaction rate terms in the time-dependent fuel conservation equation; a constant eddy diffusivity is useed to model correlation terms derived from the convective term. An expression developed for fuel consumption is solved to obtain the turbulent flame speed and the variation of mean fuel mass fraction across the flame. Comparison of the numerical analysis with experimental data indicates the importance of the quenching of the combustion reaction in high-wavenumber eddies.

Gouldin, F. C.↗
DOE OSTI2024

Combustion characteristics of diisopropoxymethane, a low-reactivity oxymethylene ether

Oxymethylene ethers (OMEs) have been studied for use as low-sooting diesel fuel additives or substitutes; very little literature discusses OMEs as spark-ignition (SI) fuels due to their typically high cetane numbers. In this work, a lower-reactivity, branched OME, diisopropoxymethane (DIPM), is evaluated to determine its effectiveness as a spark-ignition fuel, as it is the lowest-reactivity OME (as determined by Indicated Cetane Number) thus far evaluated in the literature. DIPM is synthesized in-house via acetalization from isopropanol (iPrOH) and trioxane using standard OME production practices. DIPM was then tested in a rapid compression machine (RCM) for autoignition and spark ignition characteristics, and in a modified CFR engine to determine effective octane numbers. In the RCM, an autoignition temperature sweep was performed at stoichiometric conditions from 1000/T = 1.7 - 1.0, at 5:1 inert ratio (comparable to approximately 25% EGR), where it was found that DIPM has ignition delay times 5–10x faster than isooctane and displays NTC ignition behavior. Blends with iPrOH indicate that reactivity can be matched with isooctane with low blend ratios of iPrOH in DIPM. Flame speeds were tested with a laser spark for ignition in the RCM, where the flame speed of DIPM and isooctane is determined to be comparable at engine relevant conditions. In the CFR engine, effective RON and MON based on pressure trace frequency domain measurements were determined for DIPM and a 15 vol% iPrOH in DIPM blend. Neat DIPM has (R+M)/2 = 59 and a negative sensitivity of S = -18, consistent with its NTC behavior and higher reactivity. Furthermore the DIPM/iPrOH blend has positive sensitivity and a pump-gasoline range (R+M)/2 = 89.3. DIPM on its own is unlikely to be an effective SI fuel, however, when blended with iPrOH as an ON booster, it may be a promising SI candidate fuel.

09 BIOMASS FUELS↗
NASA NTRS1991

Laser induced spark ignition of methane-oxygen mixtures

Results from an experimental study of laser induced spark ignition of methane-oxygen mixtures are presented. The experiments were conducted at atmospheric pressure and 296 K under laminar pre-mixed and turbulent-incompletely mixed conditions. A pulsed, frequency doubled Nd:YAG laser was used as the ignition source. Laser sparks with energies of 10 mJ and 40 mJ were used, as well as a conventional electrode spark with an effective energy of 6 mJ. Measurements were made of the flame kernel radius as a function of time using pulsed laser shadowgraphy. The initial size of the spark ignited flame kernel was found to correlate reasonably well with breakdown energy as predicted by the Taylor spherical blast wave model. The subsequent growth rate of the flame kernel was found to increase with time from a value less than to a value greater than the adiabatic, unstretched laminar growth rate. This behavior was attributed to the combined effects of flame stretch and an apparent wrinkling of the flame surface due to the extremely rapid acceleration of the flame. The very large laminar flame speed of methane-oxygen mixtures appears to be the dominant factor affecting the growth rate of spark ignited flame kernels, with the mode of ignition having a small effect. The effect of incomplete fuel-oxidizer mixing was found to have a significant effect on the growth rate, one which was greater than could simply be accounted for by the effect of local variations in the equivalence ratio on the local flame speed.

Santavicca, D. A.↗
NASA NTRS1995

Effects of pressure gradients on turbulent premixed flames

The influence of a constant acceleration on a turbulent premixed flame is studied by direct numerical simulation. This acceleration induces a mean pressure gradient across the flame brush, leading to a modification of the turbulent flame structure due to differential buoyancy mechanisms between heavy cold fresh and light hot burnt gases. Such a pressure gradient may be encountered in practical applications in ducted flames. A favorable pressure gradient, i.e. the pressure decreases from unburnt to burnt gases, is found to decrease the flame wrinkling, the flame brush thickness, and the turbulent flame speed. A favorable pressure gradient also promotes counter-gradient turbulent transport. On the other hand, adverse pressure gradients tend to increase the flame brush thickness and turbulent flame speed, and promote classical gradient turbulent transport. The balance equation for the turbulent flux of the Favre averaged progress variable is also analyzed. The first results show that the fluctuating pressure term, cannot be neglected as generally assumed in models. Simple models assuming that a high mean pressure gradient may only be balanced by the cross-dissipation term seem too approximate. This analysis has to be continued to compare simulation data and closure schemes proposed for the transport equation. The analysis developed by Veynante et al.(1995) has been extended to imposed acceleration and mean pressure gradients. A simple model for the turbulent flux is proposed and validated from simulation data. Then, a modified criterion is derived to delineate between counter-gradient and gradient turbulent diffusion. In fact, counter-gradient diffusion may occur in most practical applications, especially for ducted flames.

Veynante, D.↗
NASA NTRS1993

Direct simulations of premixed turbulent flames with nonunity Lewis numbers

A principal effect of turbulence on premixed flames in the flamelet regime is to wrinkle the flame fronts. For nonunity Lewis numbers, Le is not equal to 1, the local flame structure is altered in curved regions. This effect is examined using direct numerical simulations of 3D isotropic turbulence with constant density, single-step Arrhenius kinetics chemistry. Simulations of Lewis numbers 0.8, 1.0, and 1.2 are compared. At the local level, curvature effects dominated changes to the flame structure while strain effects were insignificant. A strong Lewis-number-dependent correlation was found between surface curvature and the local flame speed. The correlation was positive for Le less than 1 and negative for Le greater than 1. At the global level, strain-related effects were more significant than curvature effects. The turbulent flame speed changed significantly with Lewis number, increasing as Le decreased. This was found to be due to strain effects that have a nonzero mean over the flame surface, rather than to curvature effects that have a nearly zero mean. The mean product temperature was also found to vary with Lewis number, being higher for Le greater than 1 and lower for Le less than 1.

Rutland, C. J.↗
DOE OSTI2023

Laminar Burning Speed Measurements of Hydrogen/Natural Gas Mixtures

Abstract To address the shortage of fossil fuels and the environmental impact of exhaust emissions, research efforts in combustion seek to identify candidates for sustainable fuels. Hydrogen is an example, from which water is produced as the main combustion product. However, when used as neat hydrogen, it is very difficult to control hydrogen combustion due to its high flame speed, pre-ignition propensity, and flashback characteristics. One method to control hydrogen combustion is to blend it with a well-established fuel. Natural gas is a common fuel for use in engines or gas turbines. Natural gas is characterized by slow flame speeds and poor lean-burn ability; thus, engine power is decreased in the lean-burn region. Consequently, natural gas engines are typically operated at stoichiometric conditions to maximize output. Blending hydrogen to natural gas has several advantages: (i) Control of hydrogen’s ignition characteristics, (ii) extension of Natural gas’s lower flammability limit — making it easier to ignite, and (iii) reduced greenhouse gas emissions. In this study, the laminar burning speed (LBS) for neat natural gas and natural gas/hydrogen mixtures at 5 atm and 296 K were measured. Schlieren optical imaging was utilized to validate laminar flame conditions and further investigate the structure of natural gas/hydrogen flames. Results indicate that replacing 50% of natural gas with hydrogen increases the peak laminar burning velocity by a factor of ∼1.6 times. LBS simulations were conducted with NUI 1.1 and UCF NG/H2 mechanisms; Predictions by both mechanisms were found to be satisfactory for neat NG mixtures. However, for 50% NG/ 50% H2 mixture, the true LBS for fuel-lean conditions was under-predicted by both models, while predictions for fuel-rich conditions were satisfactory. Additionally, a literature review and similar experimental analysis will be performed for methane, ammonia, and hydrogen fuel blends to better understand the combustion phenomena of natural gas fuels.

Yovino, Louis↗
DOE OSTI2023

Experimental and numerical investigation of flame stabilization and pollutant formation in matrix stabilized ammonia-hydrogen combustion

Ammonia (NH 3 ) is a carbon-free fuel that offers an attractive alternative for reducing greenhouse gas emissions. However, the slow flame speed, low heating value, and emissions of nitrogen-containing pollutants present significant issues for practical combustion applications. To address these issues, we investigate the use of matrix stabilized combustion. In this type of burner, combustion is performed within an inert porous ceramic foam, heat is recirculated by solid conduction and radiation, which enhances flame speed and combustion stabilization, thereby permitting combustion over a wide range of equivalence ratio conditions. We present a new porous media burner (PMB) capable of stabilizing NH 3 /air flames at ambient conditions. An extensive experimental characterization of the stability of this burner is conducted with up to 30% by volume of hydrogen (H 2 ) in the fuel stream. A 15:1 turndown ratio is demonstrated, with a high thermal power density of 62 MW m -3 . Concentrations of NO, unburnt NH 3 , and H 2 in the exhaust stream are measured. Two regimes are identified for low NO operation: rich and very lean. For rich conditions, NO emissions decrease with increasing equivalence ratio and decreasing H 2 blending. Unburnt NH 3 emissions follow opposite trends. These measurements are complemented by simulations in which the burner is represented by a coupled solid-gas reactor network. In conclusion, this model captures the burner’s pollutant emissions to good accuracy and is used to analyze the mechanisms of pollutant formation.

42 ENGINEERING↗
DOE OSTI2023

Effects of unburnt reaction progress on stretch flame dynamics under elevated temperatures

Flames in practical combustors and engines are inevitably subject to the effects of upstream chemical reaction progress and stretch, induced by elevated thermodynamic conditions and flow non-uniformities, respectively. Recent shock tube experiments and simulation studies on flame propagation have shown that flame speed under engine-relevant conditions can be enhanced with non-negligible upstream chemical reaction progress, especially when low-temperature heat release is involved in the unburnt mixture. On the other hand, depending on the mixture equivalence ratio and diluents, nonequidiffusion (including the non-unity Lewis number effect and the preferential diffusion effect) can couple with the flame stretch to fundamentally affect the flame propagation, which can manifest as either facilitation or suppression. Depending on the transport property of a reacting mixture, there hence can be either inhibition or promotion from unburnt reaction progress and stretch effects on flame propagation. In the current work, through one-dimensional numerical simulations of transient planar and spherical flames of n-heptane/air under elevated thermodynamic conditions, the combined effects of upstream chemical reaction progress and stretch on flame propagation are investigated. Results show that for both lean and rich n-heptane/air mixtures, flame speed can be substantially promoted with reaction progress, while the rich mixtures can exhibit opposite stretch dependence after first-stage ignition. Different definitions of effective Lewis number are adopted to explain the change in Markstein length for spherical flame in lean and rich mixtures reformed by the low temperature chemistry. Further, this work fills an important gap in laminar premixed flame research relevant to practical combustion systems and can provide useful insight into local turbulent flame behaviors and phi-sensitivity in engine combustion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2026

Optimization of a 10–Step Reduced CH₄/O₂ Combustion Mechanism for RDRE Applications

A 10-step, 9-species reduced mechanism for methane/oxygen combustion is evaluated and optimized for use in rotating detonation rocket engine (RDRE) simulations at an operating pressure of 10 bar. The mechanism is assessed against GRI-Mech 3.0 for ignition delay times, adiabatic equilibrium temperature and species, Chapman-Jouguet (CJ) detonation parameters, and laminar flame speed. A sequential Nelder–Mead optimization procedure is applied to the rate constants of reactions R1, R4, and R5, targeting ignition delay agreement over the equivalence ratio range φ = 1.0–1.4 and temperature range T = 1400–2000 K. The optimized mechanism achieves ignition delay agreement within 28% of GRI-Mech 3.0 for the temperature range relevant to RDRE operation (τ ≥ 5 μs). Adiabatic equilibrium temperatures and CJ detonation parameters are reproduced within 0.15% of GRI-Mech 3.0 values, confirming thermodynamic consistency of the mechanism. Laminar flame speed predictions deviate significantly from GRI-Mech 3.0, which is attributed to the absence of HO₂ chemistry in the reduced mechanism; this limitation does not affect RDRE simulation fidelity since laminar flame propagation is of secondary importance in RDREs.

Computational Fluid Dynamics↗
DOE OSTI2024

Piston geometry and stroke optimization for high efficiency propane spark ignition engines

Propane has unique properties and offers interesting characteristics for high-efficiency spark ignition engines. Its high volatility reduces or completely eliminates fuel-wall wetting and facilitates fuel air mixing. Furthermore, propane has a research octane number of 112 and a high octane sensitivity of 15. Finally, its laminar flame speed is on the same order as that of conventional gasoline, and it exhibits high dilution tolerance. Modern spark ignition internal combustion engines rely on fast combustion rates and high dilution to achieve high brake thermal efficiencies. To accomplish this, high stroke-to-bore ratios and high geometric compression ratios have been used in new engine designs. Therefore, propane’s relatively high laminar flame speeds, high knock resistance, and dilution tolerance make it an excellent candidate fuel for modern spark ignition engines. The objective of this work is to co-optimize the piston geometry and the engine stroke to maximize the efficiency of a spark-ignition engine fueled with propane. 3D computational fluid dynamics (CFD) simulations employing the extended coherent flamelet model were used to study the parametric effects of piston shape and stroke length. A piston geometry based on high performing pistons was parameterized using four controlling parameters. The piston geometry and engine stroke design space was explored using deterministic and quasi-random sampling techniques. In conclusion, a Gaussian process regression model was built using the simulation data to explain the results observed.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Comparing Global Spray Combustion Characteristics and Local Shot-to-Shot Variations in a Reacting n -Heptane Spray

In support of efforts to develop improved models of turbulent spray behavior and combustion in diesel engines, experimental data and analysis must be obtained for guidance and validation. For Reynolds-averaged Navier–Stokes (RANS)-based Computational fluid dynamics (CFD) modeling approaches, representative ensemble average experimental results are important. For high-fidelity models such as large eddy simulations (LES)-based CFD, precise individual experimental results are desirable. However, making comparisons between a given experiment and LES is a challenge since local parameters cannot be directly compared. In this work, an optically accessible constant pressure flow rig (CPFR) is utilized to acquire diesel-like fuel injection and reaction behavior simultaneously with three optical diagnostic techniques: rainbow Schlieren deflectometry (RSD), OH* chemiluminescence (OH*), and two-color pyrometry (2CP). The CPFR allows a large number of repeated injection experiments to be performed for statistical analysis and convergence using ensemble-averaging techniques, while maintaining highly repeatable test conditions. Even for stable test conditions, variations in local turbulent fuel–air mixing introduce variability, which manifests as significant differences in OH* and 2CP results. Experimental measurements of characteristic parameters including liquid and vapor jet penetration, liftoff length, soot temperature and concentration, and turbulent flame speed, along with the shot-to-shot variability of each dataset, are presented and discussed. Finally, a statistical method is utilized to analyze the extent of this variability, and to identify superlative injections within the dataset for discussion and analysis of shot-to-shot variations.

42 ENGINEERING↗