Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fluid Film”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Computational Analysis of Water Film Thickness During Rain Events for Assessing Hydroplaning Risk, Part 1: Nearly Smooth Road Surfaces

In the research work reported here, both two- and three-dimensional computational fluid dynamics (CFD) analysis was used to investigate modern road geometries that were not frequently encountered in the latter half of the 20th century but are much more common today. The relation of newer road geometries to the water film thickness that develops on travel lanes was a major focus of this work.

42 ENGINEERING↗
DOE OSTI2022

Surface Heater Fabrication Using Micro-Lithography for Transpiration Cooling Heat Transfer Coefficient Measurements

Abstract Transpiration cooling is able to provide more uniform coolant coverage than film cooling to effectively protect the component surface from contacting the hot gas. Due to numerous coolant ejection outlets within a small area at the target surface, the experimental thermo-fluid investigation on transpiration cooling becomes a significant challenge. Two classic methods to investigate film cooling, the steady-state foil heater method and the transient thermography technique, fail for transpiration cooling because the foil heater would block numerous coolant outlets, and the semi-infinite solid conduction model no longer holds for porous plates. In this study, a micro-lithography method to fabricate a silver coil pattern on top of the additively manufactured polymer porous media as the surface heater was proposed. The circuit was deliberately designed to cover the solid surface in a combination of series connection, and parallel connection to ensure the power in each unit cell area at the target surface was identical. With uniform heat flux generation, the steady-state tests were conducted to obtain distributions of a pair of parameters, adiabatic cooling effectiveness, and heat transfer coefficient (HTC). The results showed that the adiabatic cooling effectiveness could reach 0.65 with a blowing ratio lower than 0.5. Meanwhile, the heat transfer coefficient ratio (hf/h0) of transpiration cooling was close to 1 with a small blowing ratio at 0.125. A higher HTC ratio was observed for smaller pitch-to-diameter cases due to more turbulence intensity generated at the target surface.

Engineering↗
DOE OSTI2022

Molecular-scale mechanisms of CO 2 mineralization in nanoscale interfacial water films

The calamitous impacts of untethered carbon emission from fossil-fuel-burning energy infrastructure calls for accelerated development of large-scale CO 2 capture, utilization, and storage technologies that are underpinned by fundamental understanding of molecular-level chemical processes. In the subsurface, rocks rich in divalent metals can react with CO 2 , permanently sequestering it in the form of stable metal carbonate minerals, with the CO 2 -H 2 O composition of the post-injection pore fluid acting as a primary control variable. Herein, we compare mechanistic reaction pathways for aqueous-mediated carbonation with carbon mineralization occurring in nanoscale adsorbed water films. In the extreme of pores filled with a CO 2 -dominant fluid, carbonation reactions are confined to nanometer-thick water films coating mineral surfaces, which enable metal cation release, transport, nucleation, and crystallization of metal carbonate minerals. Though seemingly counterintuitive, laboratory studies have demonstrated facile carbonation rates in these low water environments, which in recent years has begun to be better understood in mechanistic detail. The overarching objective of this review is to delineate the unique underlying molecular-scale reaction mechanisms that govern CO 2 mineralization in these reactive and dynamic quasi-2D interfaces. Here. we highlight the importance of understanding unique properties in thin water films, such as how water dielectric properties, and consequently ion solvation/hydration behavior, can change under nanoconfinement. We conclude by identifying important frontiers for future work and opportunities to exploit these fundamental chemical insights for decarbonization technologies in the 21st century.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Microfluidic film evaporation with femtosecond laser-patterned surface

Systems, apparatuses, and methods for microfluidic fluid evaporation using femtosecond laser-patterned surfaces are disclosed. A microfluidic device may comprise a femtosecond laser-patterned substrate having at least one input path and at least one output path. The femtosecond laser-patterned substrate may comprise both superhydrophobic and superhydrophilic sections. Fluid deposited at an input path may be wicked to an output path due to the surface pattern. A heating device may be provided to heat the fluid to evaporate volatiles therefrom. Vacuums and gas streams may be used to aid in volatile removal. Gas streams may add gas to the microfluidic device to react with the fluid.

Pearson, Connor Daniel↗
DOE OSTI2022

Mesoscale Polymer Surfactants: Photolithographic Production and Localization at Droplet Interfaces

Stabilization of fluid droplets, classically as oil-in-water or water-in-oil emulsions, is typically conducted using molecular surfactants or small particulates that localize at oil-water interfaces. In this paper, we describe a method whereby thin polymer films are converted photolithographically to ribbon-like mesoscale objects, which in turn adsorb to fluid inter-faces where they extend as appendages, or arms, from the droplet surface. These “mesoscale polymer surfactants”, or MPSs, were prepared from thin polymer films containing reactive functional moieties, including coumarin for photo-crosslinking, triphenylsulfonium for photoacid generation, and tert-butyl ester for solubility switching. The resultant MPSs, prepared initially on Si substrates, were released into water to reveal an exquisite shape sensitivity (forming straight, bent, or helical structures) and affinity for droplet interfaces based on their preparation conditions and the properties of the surrounding liquid. Notably, the lithographic techniques employed were amenable to differentiating the wettability of MPS segments, affording access to diblock-like MPSs which adhered to dispersed droplets via their hydrophobic segments, allowing their hydrophilic segments to extend into the continuous phase.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Optimization of spray breakup model parameters for predicting fuel spray and film characteristics in gasoline direct injection engines

This study investigated the behavior of gasoline direct injection (GDI) sprays using computational fluid dynamics (CFD). The authors developed an approach to identify optimal spray breakup model parameters by evaluating an error function across numerous simulations, with the goal of minimizing discrepancies from experimental data. Using the optimal setup, the simulated spray matched well with projected liquid volume distributions, liquid penetration, and spray width measured in a constant-pressure continuous-flow chamber. To further validate the approach, the same setup was tested across various fuels, injectors, and operating conditions. Subsequently, the optimal setup, along with a recently developed spray-wall interaction model, were applied to a direct-injection spark-ignited engine under late-injection conditions to predict and evaluate fuel film formation and evolution at varying engine coolant temperatures. Here, with the centrally mounted injector directing the spray toward the piston, simulations indicated that the spray tends to impinge on the piston surface. The proposed simulation framework also accurately captured the aggregate film area on the piston surface, aligning with previously published experimental results. Moreover, simulations showed that increasing the coolant temperature from cold start conditions (333 K) to warm conditions (363 K) reduced the fuel mass deposited on the piston by roughly 50%. Furthermore, for the spray-guided engine configuration studied in this work, the CFD model predicted minimal film deposition on the spark plug electrodes regardless of the coolant temperatures due to a relatively weak in-cylinder flow during the compression phase.

Computational fluid dynamics (CFD)↗
DOE OSTI2022

Film Cooling Performance Prediction for Air and Supercritical CO 2

The current study explores the possibility of cooling the vanes and blades of a direct-fired sCO 2 turbine using film cooling. The operating conditions of a direct-fired sCO 2 cycle and thermophysical properties of the fluid at those conditions can alter the flow field characteristics of the coolant jet and its mixing with the mainstream. Very little information is present in the literature regarding the performance of film cooling geometries employing supercritical CO 2 . The objective of this study is to estimate the resulting film cooling effectiveness while also capturing the effects of the crossflow-to-mainstream velocity ratio on the coolant jet. Herein, a computational fluid dynamic model is used to study the coolant jet exiting a cylindrical hole located on a flat plate, with the coolant fed by an internal channel. Steady-state Reynolds-averaged Navier–Stokes equations were solved along with the (shear-stress transport) SST k–ω model to provide the turbulence closure. The operating conditions for the direct-fired sCO 2 turbine are obtained using an in-house Cooled Turbine Model. Numerical predictions revealed that the crossflow effects and jet lift-off were more pronounced in the case of sCO 2 when compared to air. Spatial distribution of flow field and cooling effectiveness are presented at different operating conditions.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2023

The role of stress and fluid saturation on the acoustic response of fractured rock

Standard rock physics models are formulated to describe the behavior of porous sedimentary reservoirs, with clean sandstones being the archetypal system; however, many situations demand geophysical monitoring of rocks with significantly different structures, such as low porosity, fractured reservoirs. Conventional models also suggest that these “stiff” reservoirs can be challenging to monitor seismically due to small fluid substitution effects, but the presence of fractures leads to stress dependence which may be leveraged for remote monitoring purposes. Using samples from the Duperow Formation (dolostone) obtained from the Danielson test well in Kevin Dome, MT, we conducted ultrasonic and multi-scale structural (profilometry, synchrotron micro-tomography, pressure sensitive film) measurements on naturally fractured core in order to characterize the effects of fluid substitution and effective stress on the acoustic response of fractured reservoir rock with a focus in particular on the textural and seismic characteristics of natural fractures. We find that changes in effective stress can yield changes in velocity of up to 20% and changes in attenuation up to 200%. Measured fluid substitution effects are resolvable, but stress effects dominate. These measurements provide insight into the physical processes controlling acoustic response of fractured rocks in general and can also be used to inform monitoring efforts in fractured reservoirs.

58 GEOSCIENCES↗
DOE OSTI2022

Controlling Rheology of Fluid Interfaces through Microblock Length of Sequence-Controlled Amphiphilic Copolymers

Previous studies have demonstrated that films of sequence-controlled amphiphilic copolymers display contact angles that depend on microblock size. This suggests that microblock length may provide a means of tuning surface and interfacial properties. In this work, the interfacial rheology of a series of sequence-controlled copolymers, prepared through the addition of bicyclo[4.2.0]oct-1(8)-ene-8-carboxamide (monomer A) and cyclohexene (monomer B) to generate sequences up to 24 monomeric units composed of (A m B n ) i microblocks, where m, n, and i range from 1 to 6. Interfacial rheometry is used to measure the mechanical properties of an air–water interface with these copolymers. As the microblock size increases, the interfacial storage modulus, G', increases, which may be due to an increase in the size of interfacial hydrophobic domains. Small-angle X-ray scattering shows that the copolymers have a similar conformation in solution, suggesting that any variations in the mechanics of the interface are due to assembly at the interface, and not on solution association or bulk rheological properties. This is the first study demonstrating that microblock size can be used to control interfacial rheology of amphiphilic copolymers. Here, the results provide a new strategy for controlling the dynamics of fluid interfaces through precision sequence-controlled polymers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Current fluctuations and domain depinning in quasi-two-dimensional charge-density-wave 1 T -TaS 2 thin films

We investigated the temperature dependence of the current fluctuations in thin films of the quasi-two-dimensional 1T-TaS 2 van der Waals material. The current fluctuations, determined from the derivative current–voltage characteristics of two-terminal 1T-TaS 2 devices, appear prominently at the electric fields that correspond to the transitions between various charge-density-wave macroscopic quantum condensate phases and at the onset of the depinning of the charge density wave domains. The depinning threshold field, ED, monotonically increases with decreasing temperature within the nearly commensurate charge-density-wave phase. The ED value increases with the decreasing 1T-TaS 2 film thickness, revealing the surface pinning of the charge density waves. Our analysis suggests that the domain depinning is pronounced in the nearly commensurate phase. It is induced by the electric field but facilitated by local heating. Furthermore, the measured trends for ED of the domain depinning are important for understanding the physics of charge density waves in quasi-two-dimensional crystals and for developing electronic devices based on this type of quantum materials.

2D materials↗
DOE OSTI2022

System, method, and apparatus relating to colloidosomes

An ultra low density film and an ultra low density solid material are produced by the steps of providing a vessel, introducing two immiscible fluids into the vessel, adding nanocrystals to at least one of the two immiscible fluids, applying a shear force to the two immiscible fluids and the nanocrystals in a manner that causes the nanocrystals to self-assemble and form colloidosomes. The colloidosomes amass and evaporation of the two fluids produces dried colloidosomes. The ultra low density self-assembled colloidosomes are hollow self-assembled colloidosomes, which are formed into the ultra-low density film and the ultra-low density solid.

Orme, Christine A.↗
DOE OSTI2022

Direct Multimodal Nanoscale Visualization of Early Phosphorus-Based Antiwear Tribofilm Formation

Understanding the mechanism of antiwear (AW) tribofilm formation and how to tune surface chemistry to control functionality is essential for the development of the next generation of oil lubricants. In particular, understanding and optimizing early AW tribofilm formation can increase the energy efficiency of mechanical systems. However, the mechanism for how these films form is not well understood. The majority of prior work has focused on analyzing only end-of-test surfaces long after the film has formed. In this work, we develop an in situ multimodal chemical imaging methodology to directly visualize the early formation of AW films on steel surfaces. We investigate an oil formulation containing a phosphorus-based additive commonly used to protect surfaces from wear and fatigue processes in machine elements, such as gears, bearings, and sliding contacts. Using nanoscale multimodal chemical imaging on combined platforms of atomic force microscopy (AFM) coupled directly with in situ nano-infrared (nano-IR) spectroscopy, and further combined ex situ with time-of-flight secondary ion mass spectrometry (ToF-SIMS), we demonstrate a direct correlation between changes in friction and local surface chemistry. In these experiments, the AFM probe acts as a single asperity contact to generate the tribofilm as well as a tool to analyze it in situ as it is forming. To verify our in situ measurements, we compare these results to the ex situ ToF-SIMS of macroscale block-on-ring tribometer-formed samples. We report the understanding gained here on how AW films form and how film properties can be modified by tuning the chemistry of the additives will facilitate developing transmission fluids to meet increasing demands for vehicle performance and efficiency.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Aggregation Dynamics of Colloidal Particles in Tin Perovskite Crystalline Film Formation

We present an approach to understanding the crystallization of tin-based perovskite films for photovoltaic applications, starting from precursor suspensions processed via spin-coating. By integrating colloidal theory with the fluid dynamics of suspensions, this approach elucidates the influence of both chemical variables and process parameters on the crystallization pathways of perovskite suspensions and the resulting microstructural features of the solid films. Specifically, the incorporation of SnCl 2 as an additive was found to accelerate crystallization, whereas tBP induces a slowdown of the process leading, however, to a marked improvement in film uniformity and microstructural quality.

Crystallization↗
DOE OSTI2022

Numerical simulation of evaporating wavy falling liquid films in laminar gas streams

Numerical simulations are performed to investigate the interfacial heat and mass transfer from evaporating wavy falling liquid films in interaction with laminar gas streams. The OpenFOAM solver has been used to conduct the simulations where the liquid-gas interface is resolved using the Volume of Fluid method of solving for three phases, i.e., liquid, vapor, and air. The configuration considered is a falling liquid (water) film on a heated vertical plate with a confined laminar moist air (gas) flow that is either (a) co-current or (b) counter-current to the downward liquid flow. The evaporation at the liquid-gas interface is driven by the interfacial gradient of the vapor mass fraction. Interfacial waves are triggered using a monochromatic forcing disturbance that leads to sinusoidal or solitary waves forming at the liquid-gas interface under respective forcing frequencies. Further, the numerical model is validated with the available experimental data. The results show nearly a 15% enhancement in time-averaged Sherwood number (Sh) due to film waviness (sinusoidal or solitary) at the lower volumetric gas flow rate, Q g = +50 (co-current) and Q g = -50 (counter-current). This enhancement in the Sh for both the waves further increases by 11% with Q g = +800 and 196% with Q g = -800. A closer examination of the mass transfer process over a wave demonstrates that with Q g = +50, the concentration of the gas side streamlines at the trough locations of the wave leads to higher values of Sh at these locations. However, with Q g = +800, although the overall Sh increases, vortices appear at the wave trough locations, leading to a corresponding decrease in the local Sh values. Correlations are proposed for predicting Sh under co-current and counter-current gas flow effects.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Manipulation and statistical analysis of the fluid flow of polymer semiconductor solutions during meniscus-guided coating

Recent work in structure–processing relationships of polymer semiconductors have demonstrated the versatility and control of thin-film microstructure offered by meniscusguided coating (MGC) techniques. Here, we analyze the qualitative and quantitative aspects of solution shearing, a model MGC method, using coating blades augmented with arrays of pillars. The pillars induce local regions of high strain rates—both shear and extensional—not otherwise possible with unmodified blades, and we use fluid mechanical simulations to model and study a variety of pillar spacings and densities. We then perform a statistical analysis of 130 simulation variables to find correlations with three dependent variables of interest: thin-film degree of crystallinity and transistor field-effect mobilities for charge-transport parallel (Μ para ) and perpendicular (Μ perp ) to the coating direction. Our study suggests that simple fluid mechanical models can reproduce substantive correlations between the induced fluid flow and important performance metrics, providing a methodology for optimizing blade design.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Highly Saturated Glassy Liquid Crystal Films Having Nano- and Microscale Thicknesses for High-Power Laser Applications

The optical properties of glassy liquid crystals (GLC’s) designed to provide high resistance to laser-induced damage are explored. GLC’s readily enable freezing of the anisotropic ordering of liquid crystals into the glassy state. This solidity avoids issues of fluid leakage while providing mechanical robustness and the promise of single-substrate coatings or stand-alone films of nanometer to micron thicknesses. A series of three increasingly saturated GLC’s was synthesized and tested for their thin-film (hundreds of nanometers to tens of micrometers) high-peak-power laser-damage resistance with nanosecond pulses at 1053 nm, 532 nm, and 351 nm, as well as their durability under continuous-wave, broadband ultraviolet illumination. As a result, the GLC’s with higher degrees of saturation demonstrated high resistance to laser-induced damage, extending from the near infrared to the ultraviolet spectral region.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Transport of an intense proton beam from a cone-structured target through plastic foam with unique proton source modeling

Laser-accelerated proton beams are applicable to several research areas within high-energy density science, including warm dense matter generation, proton radiography, and inertial confinement fusion, which all involve transport of the beam through matter. Here, we report on experimental measurements of intense proton beam transport through plastic foam blocks. The intense proton beam was accelerated by the 10 ps, 700 $\textit{J}$ OMEGA EP laser irradiating a curved foil target, and focused by an attached hollow cone. The protons then entered the foam block of density 0.38 g/cm 3 and thickness 0.55 or 1.00 mm. At the rear of the foam block, a Cu layer revealed the cross section of the intense beam via proton- and hot electron-induced Cu-K α emission. Images of x-ray emission show a bright spot on the rear Cu film indicative of a forward-directed beam without major breakup. 2D fluid-PIC simulations of the transport were conducted using a unique multi-injection source model incorporating energy-dependent beam divergence. Along with postprocessed calculations of the Cu – $K_α$ emission profile, simulations showed that protons retain their ballistic transport through the foam and are able to heat the foam up to several keV in temperature. The total experimental emission profile for the 1.0 mm foam agrees qualitatively with the simulated profile, suggesting that the protons indeed retain their beamlike qualities.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗