Search NASA⌕ Search

SEARCH · Search NASA

Results for “Friction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Power Cylinder Friction Reduction Through Coatings, Surface Finish and Design

About 7-10% of the total energy input in a vehicle is lost due to mechanical friction, and in an engine, about 50% of the total frictional losses occur at the interface between the cylinder and pistons and piston rings. Therefore, this interface offers great opportunities for friction reduction. The goal of this proposed study is to demonstrate friction reduction potential using advanced coatings, surface finish, and design on power cylinder system containing cylinder bore, piston rings, crankshaft, and advanced engine oils. Experience through years of research in this area lead us to believe that full benefit potential can be realized only by considering a systems approach.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2023

Friction Experiment Data Analysis

The Spent Fuel Waste Disposition (SFWD) program under the U.S. Department of Energy (DOE) is planning a seismic shake table test of full-scale dry storage systems of spent nuclear fuel (SNF) to close the gap related to the seismic loads on the fuel assemblies in dry storage systems. This test will allow for quantifying the strains and accelerations on surrogate fuel assembly during representative earthquakes. A concrete layer will be installed on the shake table before the test to simulate conditions representative of an ISFSI pad. In the shake table tests with the vertical cask, the cask will be free-standing because this is representative of all, except two, ISFSIs in the U.S. with vertical dry storage casks. The static and dynamic friction coefficients between the steel bottom of the cask and the concrete layer on the shake table are important parameters that will affect cask behavior during the test. These parameters must be known for the pre- and post-test modelling, data analysis, and model validation. The friction experiment was performed at the Engineering Department of the University of New Mexico (UNM) to determine the friction coefficients between a steel plate with the same finish as the bottom of the vertical cask manufactured for the test and different concrete surfaces. In this experiment the steel plate was fixed and the concrete sample was pulled over the plate with a constant displacement rate using an MTS machine. This allowed for collecting continuous horizontal force data over the length of the steel plate. Four displacement rates and three vertical loads were used. The tests were performed with four concrete blocks with different degrees of the surface roughness - light sandblast, light to medium sandblast, medium bush hammer, and heavy sandblast. The total number of tests was 48. The data were used to calculate static and dynamic friction coefficients.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Friction and wear of nuclear graphite exposed to molten FLiNaK salt environment

This report formally documents the completion of the Advanced Reactor Technologies Level 3 Milestone (M3TG-25OR0501104), “Initiate graphite wear studies of graphite samples exposed to molten salt environment,” due August 1, 2025. The report summarizes the ongoing activities aimed at characterizing the friction and wear behavior of graphite in molten LiF–NaF–KF (FLiNaK) salt environment. The wear and friction behavior of self-mated ET-10 nuclear graphite were tested at varying temperatures (550°C and 650°C), contact loads (40 and 80 N) and sliding speeds (1 and 10 mm/s) in a controlled argon environment. The results were compared to the wear and friction behavior of the same graphite material in a dry argon environment. This report presents initial studies on the friction and wear behavior of graphite in sliding contact mode, with future work focused on investigating the graphite matrix materials, as well as rolling and impact contact modes. The outcomes of this report could provide insights into assessing the integrity of the graphitic components of pebble-bed fluoride salt–cooled high-temperature reactors (PB-FHRs) to enhance their safe operation.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Friction reduction for engine components

The present invention relates to techniques for lowering friction between moving surfaces of, for example, an internal combustion engine. Friction reduction is achieved by adding texture modifications to surfaces that come in contact with each other. Texture modifications that reduce friction in accordance with the present invention include dimples of varying geometries and depths ion the surfaces of components. The present invention also relates to the fabrication technique for applying the texture to the surfaces. In another embodiment, the patterned soft mask is applied onto a large surface (flat or curved including cylindrical rollers surfaces) to be followed by electrochemical etching to imprint the textures onto the component And, in another embodiment, a diamond-like-carbon (DLC) film may be applied to the turbine component to also reduce friction.

Hsu, Stephen M.↗
DOE OSTI2022

Low friction coatings

A low friction, wear-resistant surface operable at high temperatures and high loads with a low coefficient of friction including boron nitride and graphene-oxide on steel or nanodiamonds and graphene on aluminum. The low friction, wear-resistant surface remains with a coefficient of friction in the superlubric regime at temperatures in between about 200° C. and 970° C.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Friction Stir Processed Repair Welding of Dry Storage Canisters and Mitigation Strategies: Effect of Engineered Barrier Layer on Environmental Degradation

The proposed project aims to develop a friction sir based repair technique to heal cracks of stainless steel dry storage canisters (DSCs), created by the effect of stress corrosion cracking (SCC). In real service conditions, the welded parts of the canisters become prone to SCC under exposure to aggressive chemical environment. The focus of the project is on developing a mitigation strategy that can be implemented for countering SCC in DSCs following a two-pronged approach: (i) apply friction stir processing (FSP) as a crack repair technique while creating compressive residual stresses at the canister material surface, thus improving resistance against SCC; (ii) add molybdenum and/or nitrogen by friction stir based alloying process to create compositions that improve pitting resistance and thus enhance resistance against SCC. The specific project objectives are listed below: • Investigate FSW of 304L SS a potential repair welding technique of dry storage canisters; • Optimize the FSW parameters to introduce surface compressive stress profiles in the weldments; • Develop a FSP method to surface alloy the 304L with nitrogen and Mo by adding CrN and Mo powders; • Evaluate the surface compressive residual stress profile during FSW and FSP processes; • Evaluate the localized corrosion resistance of the FSW and FSP samples as a function of temperature, chloride concentration, and surface alloy composition; • Evaluate the SCC behavior of the FSW and FSP samples as a function of stress, chloride concentration, and temperature at different surface chemistries and induced residual stress profiles.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Investigation of Raster Pattern Spacing and Direction for Friction Stir Additive Manufacturing of Al-5083

Friction stir additive manufacturing (FSAM) is a sheet-lamination based additive manufacturing technique. In addition to the traditional factors that govern the friction stir process-structure-property relationship, the processing history is convoluted by the in-plane raster pattern and repeated thermal cycling from subsequent layers. This can lead to complex thermal gradients within the workpiece and reprocessing of material. Here, this work aims to understand the impact of raster pattern spacing and direction on the microstructure and properties during friction stir additive manufacturing of Al-5083. Control of the raster spacing can lead to an increase in hardness of up to 18% from the base material and defect-free joining. These results are then directly demonstrated at the component-scale for FSAM of Al-5083.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Pitting behavior of friction stir repair-welded 304L stainless steel in 3.5% NaCl solution at room temperature: role of grain and defect structures

Stainless steel (SS) canisters used for storing spent nuclear waste are prone to chloride-induced stress corrosion cracking. Friction stir welding (FSW), being a low heat input process, can be used for repair welding of these canisters. In this study, an artificial crack was introduced on the 304L SS coupons by an electric discharge machining process. The artificial crack was repair-welded by FSW by maintaining the tool temperature a constant at two levels (725 and 825 °C). Friction stirring significantly reduced the grain size of the stirred zone (SZ) from about 47 to 2–4 μm. The fraction of low-angle grain boundaries increased in the SZ from 2 to 37–43%. Here, on the other hand, the fraction of special grain boundaries (Σ3 and Σ9) that was ~ 50% in the base metal reduced to < 10% in the SZ. During friction stirring, the oxide layer of artificial crack was broken and aligned to form a spiral defect called lazy-S structure. All these microstructural changes affected the corrosion behavior of the FSW specimens when tested in 3.5% NaCl at room temperature using cyclic polarization, chronoamperometry, and electrochemical impedance spectroscopy. The FSW specimens showed lower polarization resistance and lower transpassive potential than those of the base metal specimens. However, the pitting protection potentials of the FSW specimens were higher than that of the base metal. The pitting behavior of the FSW specimens was influenced more by the preferential attack on the lazy-S region than by passive film breakdown. The flat band potentials of the passive film formed on the FSW specimens were more positive than that of base metal. The charge carrier density of passive film formed on the FSW specimens was higher than that of the base metal. The higher fraction of low-angle grain boundaries present in the FSW specimens could supply more number of misorientation dislocations at the metal/film interface which could form anion vacancies by a climb process leading to formation of oxide at these locations without stressing the substrate. Therefore, low-angle boundaries are considered helpful for formation of stress-free passive films that will be highly stable and enhance both pitting and stress corrosion cracking resistance.

Dry storage canister↗
DOE OSTI2023

Stress characterization for friction-stir-welded electric vehicle battery trays with application of neutron diffraction

The battery tray is an essential component that protects and controls battery-cell temperatures in electric and plug-in hybrid vehicles. The functional stress limit of the battery tray heavily depends on the residual stress acquired from the manufacturing process. Consequently, exceeding the stress limit of the battery tray during operation could compromise the battery-cell banks and may risk the vehicle's safety. Hence, understanding residual stress formation is vital for design and safety concerns. Here, in the current study, AA 6061-plates were friction stir welded to an A365 high-pressure die-cast battery tray to create sealed coolant channels in the battery tray. However, this multi-material lap friction stir weld introduces residual stress into the battery tray, resulting in distortion. This distortion was mitigated using burnishing or coining operations, though straightening the battery tray had initially unknown effects on the residual stress. Therefore, neutron diffraction was utilized to characterize residual stresses after straightening. The results indicate that the friction stir welding (FSW) operation generated residual stresses exceeding the yield strength of the material, consequently deforming the battery tray by ±3 mm from the pre-weld geometry. The burnishing operation reduced the residual stresses below the material's yield strength while restoring the tray to within ±0.75 mm of the pre-weld geometry. Similarly, the coining operation restored the battery tray to within ±0.75 mm of the pre-weld geometry, however, increasing the number of locations where the residual stress exceeds the yield strength of the material.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Impact of supercritical carbon dioxide on the frictional strength of and the transport through thin cracks in shale

Understanding the mechanical and transport behavior of thin (i.e. small aperture) cracks slipping under supercritical carbon dioxide (sc-CO 2 ) conditions is essential to evaluate the integrity of sealing formations with buoyant sc-CO 2 below and the success of waterless fracturing. The two major items of interest in this work are frictional strength and permeability change of the crack. We used a triaxial cell that permits in situ visualization to conduct and monitor slippage along the faces of narrow cracks subjected to triaxial stresses. Such cracks are analogs to small geological faults. We tested carbonate-rich, 1-inch diameter Wolfcamp shale samples that are saw cut 30° to vertical to create a thin crack. Friction coefficients ranged from about 0.6 to 0.8 consistent with expectations for brittle rocks. The sc-CO 2 generally did not alter friction coefficient over the time scale of experiments. From a transport perspective, saturating cracks with sc-CO 2 substantially decreased permeability of the crack by 26%–52%, while slip resulted in a variety of permeability responses. Overall, the combined impact of sc-CO 2 saturation and slip reduced fault permeability for all tests. Our observations support the notion that the sealing capacity of some caprocks improves when saturated with sc-CO 2 and that some slip of small fractures is not necessarily detrimental to caprock integrity.

58 GEOSCIENCES↗
DOE OSTI2023

Material flow behavior and microstructural refinement of AA6061 alloy during friction extrusion

In this work we used friction extrusion (FE), a solid phase processing technique, to produce dense, fully consolidated 5?mm rods of aluminum alloy 6061 (AA6061). The combination of large shear stresses and high temperatures at the tool-billet interface during extrusion produced equiaxed, dynamically recrystallized grains and finely distributed precipitates. Texture and microstructure evolution during extrusion was investigated in detail using scanning electron microscopy, electron backscatter diffraction, and transmission electron microscopy. Smoothed particle hydrodynamics simulation was performed to study complex material flow during extrusion. Simulation results suggest spiral material flow during extrusion which corroborated experimental results. Advantages of friction extruded microstructure over conventionally extruded counterparts are also explored using flash annealing for solution treatment followed by artificial aging. Mechanical properties of the as-friction extruded, and the artificially aged specimens were evaluated using tensile testing and compared with conventional extruded material properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Effect of feed-rod tilting on friction surfacing of steel

During the friction surfacing process, the forge-axial force, rotation rate, and traverse speed of the consumable feed-rod play crucial roles in determining the deposition rate and layer morphology. Although some researchers have studied the enhancement of deposition by introducing a backward tilt relative to the traverse direction, there has been limited investigation into the effects of other tilt orientations. Therefore, this study aims to provide a more comprehensive understanding of feed-rod tilting in friction surfacing. In this investigation, the consumable feed-rod undergoes tilting in four distinct directions: forward, backward, advancing side, and retreating side, each tested at two different tilt angles (1.5° and 3.0°). The results reveal that the feed-rod tilting can influence the deposition dynamics by altering the location and area of the rubbing interface situated between the feed-rod and the substrate. Moreover, the feed-rod tilting can significantly enhance the bond width, deposition rate, and deposition efficiency. The enhancement in deposition efficiency signifies a successful reduction in flash formation. Furthermore, a distinct layered microstructure is evident within each deposition layer, regardless of tilt conditions, indicating the unique deposition process inherent to friction surfacing. Finally, the innovative approach proposed in this study not only offers a straightforward and feasible means to improve deposition rate and efficiency but also expands the potential for constructing more intricate geometries or authentic surfaces.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Convective heat transfer and friction factor characteristics of molten salts in spirally fluted tubes

Spirally fluted tubes have been widely used for heat exchangers due to their superior heat transfer enhancement. However, most of the previous studies focused on the effects of a limited number of geometric parameters, i.e., the flute pitch and flute depth, on convective heat transfer and friction factor characteristics of low-Prandtl-number fluids, i.e., air and water. The correlations developed in these studies may not be accurate or applicable for medium-Prandtl-number fluids, such as molten salts. A numerical analysis using a Computational Fluid Dynamics (CFD) tool, STAR–CCM+, is therefore carried out in this study to systematically investigate the effects of four geometric parameters, including the flute pitch ρ, flute depth e, flute start number N s (or flute helix angle θ), and trough length L tr on convective heat transfer and friction factor characteristics of a medium-Prandtl-number fluid, FLiNaK (46.5LiF-11.5NaF-42KF mol %), in spirally fluted tubes. Additionally, the convective heat transfer and Darcy friction factor correlations are proposed and validated, with ± 20% uncertainties, for medium-Prandtl-number fluids under the following conditions: Re = 88–1600, Pr = 2.5–40, ρ/D c = 0.44–3.51, e/D c = 0.10–0.40, θ/90= 0.20–0.81, and L tr /D c = 0.71–2.16. The correlations proposed help improve the design of spirally fluted-tube heat exchangers.

42 ENGINEERING↗
DOE OSTI2023

Towards a predictive, physics-based friction model for the dynamics of jointed structures

Bolted connections are ubiquitous in mechanical designs and pose a significant challenge to understanding and predicting the vibration response of assembled structures. The present paper develops a physics-based rough contact model of the frictional interactions within a joint. This model sums over the probable interactions of asperities – defined as locally maximum surface features – to determine the contact forces. Here, the tangential contact forces vary smoothly between sticking and slipping and allow the model to better capture the qualitative trends of experimental amplitude dependent frequency and damping than previous studies. Furthermore, the novel model is generalized to allow for arbitrarily varying normal pressure including potential separation to better represent the interfacial dynamics. This includes developing a new, computationally tractable approximation to the analytical Mindlin partial slip solution for tangential loading of contacting spheres. Further, the results highlight the importance of accurately characterizing the as-built topology of the interface, the plastic behavior of the contacting asperities, the relevant length scale of asperities, and the eccentricity of asperities. A predictive friction coefficient based on plasticity provides a poor match to experiments, so fitting the friction coefficient is also considered. Numerical results are compared to experiments on the Brake-Reuß Beam to assess the predictive potential of the models. While blind predictions over-predict the slip limit, the current model presents a significant improvement in physics-based modeling and highlights areas for ongoing research.

42 ENGINEERING↗
DOE OSTI2022

Frictional and Lithological Controls on Shallow Slow Slip at the Northern Hikurangi Margin

Slow slip events (SSEs) have been identified at subduction zones globally as an important link in the continuum between elastodynamic ruptures and stable creep. The northern Hikurangi margin is home to shallow SSEs which propagate to within 2 km of the seafloor and possibly to the trench, providing insights into the physical conditions conducive to SSE behavior. We report on a suite of friction experiments performed on protolith material entering the SSE source region at the Hikurangi margin, collected during the International Ocean Discovery Program Expedition 375. We performed velocity stepping and slide-hold-slide experiments over a range of fault slip rates, from plate rate (5 cm/yr or 1.6 × 10 –9 m/s) to ~1 mm/s (10 –3 m/s) and quantified the frictional velocity dependence and healing rates for a range of lithologies atdifferent stresses. The frictional velocity dependence (a-b) and critical slip distance DC increase with fault slip rate in our experiments. We observe atransition from velocity weakening to strengthening at slip rates of ~0.3 µm/s. This velocity dependence of DC could be due to a combination of dilatant strengthening and a widening of the active shear zone at higher slip rates. We document low healing rates in the clay-rich volcaniclastic conglomerates, which lie above the incoming plate basement at least locally, and relatively higher healing rates in the chalk lithology. Finally, our experimental constraints on healing rates in different input lithologies extrapolated to timescales of 1–10 years are consistent with the geodetically inferred low stress drops and healing rates characteristic of the Hikurangi SSEs.

58 GEOSCIENCES↗
DOE OSTI2022

Frictional Behavior Downdip Along the Subduction Megathrust: Insights From Laboratory Experiments on Exhumed Samples at In Situ Conditions

Subduction megathrusts exhibit a spectrum of slip modes, including catastrophic earthquakes. Although the mechanical and frictional properties of materials sampled from subduction zones have been studied extensively, few datasets have been collected for compositions and at pressure and temperature conditions representative of those in situ. The Nankai subduction zone in southwest Japan is a well-studied margin, and abundant data provide an opportunity to advance our understanding of fault and earthquake physics. Here, we use samples exhumed in the Shimanto and Sanbagawa Belts on Shikoku Island of southwest Japan that represent analogs for materials along the present-day megathrust at depths of ~5–>25 km, and we shear these at their peak in situ pressure-temperature (P-T) conditions. Effective normal stresses range from 28 to 192 MPa, and temperatures from 105°C to 470°C. We used pore fluid pressures of 45–240 MPa, corresponding to fluid overpressure ratios λ of 0.65 and 0.90. Slip velocities of 0.1–100 μm/s were used, in order to focus on the nucleation of instability and earthquakes. We found predominantly velocity-strengthening (inherently stable) behavior under all conditions for λ = 0.65. For λ = 0.90, velocity-weakening behavior was observed at 350°C, with velocity-strengthening behavior at lower and higher temperatures. The rate/state frictional stability parameter (a-b) increases with slip velocity at temperatures up to ~200°C and remains constant or decreases with slip velocity at higher temperatures. Altogether, our results demonstrate the potentially important roles of both temperature and slip velocity in controlling the distribution of stress and frictional rheology along subduction thrusts.

58 GEOSCIENCES↗
DOE OSTI2022

Room temperature corrosion behaviour of plastically deformed AISI 304 stainless steel by friction stir welding in neutral and acidified chloride solutions

Severe plastic deformation of 304L stainless steel plate was carried out by friction stirring under an isothermal tool temperature at 825°C. The friction stirred zone showed extensive grain refinement, high fraction of low angle grain boundaries due to dislocation rearrangement, Σ3 and Σ9 special grain boundaries and discrete Fe–Cr–Mn-rich particles. Electrochemical polarisation measurements were done on the base metal (BM) and friction stir welded (FSW) specimens in the neutral and acidified 3.5% NaCl solutions. The BM showed marginally better pitting resistance in the neutral chloride solution than the FSW because of a larger fraction of special grain boundaries, and larger grain size. Whereas in acidified 3.5% NaCl solution, the FSW showed better corrosion resistance than the BM. Furthermore, the surface film of the FSW had a lower impedance and a lower defect concentration than the BM indicating higher diffusivity of point defects in the FSW.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Intercalation leads to inverse layer dependence of friction on chemically doped MoS 2

Here, we present results of atomic-force-microscopy-based friction measurements on Re-doped molybdenum disulfide (MoS 2 ). In stark contrast to the widespread observation of decreasing friction with increasing number of layers on two-dimensional (2D) materials, friction on Re-doped MoS 2 exhibits an anomalous, i.e. inverse, dependence on the number of layers. Raman spectroscopy measurements combined with ab initio calculations reveal signatures of Re intercalation. Calculations suggest an increase in out-of-plane stiffness that inversely correlates with the number of layers as the physical mechanism behind this remarkable observation, revealing a distinctive regime of puckering for 2D materials.

42 ENGINEERING↗