Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fuel Design Analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

FEASIBILITY OF RECYCLING PLUTONIUM AND MINOR ACTINIDES IN LIGHT WATER REACTORS USING HYDRIDE FUEL

The objective of this DOE NERI program sponsored project was to assess the feasibility of improving the plutonium (Pu) and minor actinide (MA) recycling capabilities of pressurized water reactors (PWRs) by using hydride instead of oxide fuels. There are four general parts to this assessment: 1) Identifying promising hydride fuel assembly designs for recycling Pu and MAs in PWRs 2) Performing a comprehensive systems analysis that compares the fuel cycle characteristics of Pu and MA recycling in PWRs using the promising hydride fuel assembly designs identified in Part 1 versus using oxide fuel assembly designs 3) Conducting a safety analysis to assess the likelihood of licensing hydride fuel assembly designs 4) Assessing the compatibility of hydride fuel with cladding materials and water under typical PWR operating conditions Hydride fuel was found to offer promising transmutation characteristics and is recommended for further examination as a possible preferred option for recycling plutonium in PWRs.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Scale effects on core design, fuel costs, and spent fuel volume of pressurized water reactors

The desire to improve the economic competitiveness and deployment pace of nuclear energy through modularization, manufacturing, and series production had led to the development of smaller size reactors. As the standard 17x17 fuel technology is mainly maintained in the pressurized water reactors (PWRs) category, this translates into a lower number of fuel assemblies in the core and sometimes a reduced fuel height. To assess the impact of such scale change in core design on fuel cycle cost and spent fuel volume, a scoping analysis tool is developed based on infinite lattice calculations, leakage, fuel management reduced models, and levelized unit cost of electricity (LCOE) estimate. As such, cost dynamics driven by fuel specific power, burnup, core leakage, feed, cycle length, fuel assembly height as well as uranium market data are captured with consistent set of assumptions and analysis methods. A selection of 5 reactor designs representative of leading PWR developers is assessed and compared. Pursuing higher specific powers and optimal burnups are highlighted as the main fuel cost reduction drivers, nevertheless, practical limitations and opportunities must be evaluated to establish the feasibility of such enhanced fuel operation. In consequence, a detailed core design is performed using SIMULATE3 code for 5 PWR variations including natural and forced coolant circulation modes, two reactor scales, power densities of 73, 112, and 123 kW/l and higher discharge burnups. Design and optimization are performed at the lattice level, for the reflector, and at the core loading level. Satisfactory steady-state operation including power distribution, coolant operating limits, and reactivity requirements are analyzed and reported in this paper. The fuel economics of the detailed core designs confirm the scoping analysis findings. Despite the unlocked power uprates in small PWRs, the achievable burnup for a given fuel specific power requires more enrichment and shorter fuel height results in higher fabrication costs per mass of fuel, which makes scaling down core size a more expensive endeavor on the fuel cycle front. Spent fuel volumes are reported for the PWRs designed in this paper. Furthermore, these volumes are driven by the core average discharge burnup regardless of the scale in consideration. Additional cost and core performance aspects related to heavy reflector gains, fuel-reflector substitution, and disposal cost policy in the U.S. are examined.

42 ENGINEERING↗

Fabrication, Welding, and Inspection Techniques in Preparation for In-Reactor Testing of Accident Tolerant Fuels

After the Fukushima events in 2011, DOE-NE in collaboration with nuclear industry shifted R&D emphasis to accident performance of LWR fuels under extended loss of active cooling and steam exposure. DOE-NE has created a roadmap for the “Development of Light Water Reactor Fuels with Enhanced Accident Tolerance.” The mission of the Accident Tolerant Fuel (ATF) Roadmap is to develop the next generation of LWR fuels with improved performance, reliability, and safety characteristics during normal operations and accident conditions and with reduced waste generation. The ultimate goal of the ATF roadmap is to support the insertion of lead fuel rods (LFRs) or lead fuel assemblies (LFAs) of an Accident Tolerant Fuel into a commercial LWR within 10 years (i.e., by the end of FY-2022). As a step toward this goal, an irradiation test series has been developed to assess the performance of proposed ATF concepts under normal LWR operating conditions. Data generated by this test program will be used to establish the feasibility of certain aspects of proposed ATF concepts, as well as provide information to support screening among concepts; as such, it is an integral part of Phase I: Feasibility Assessment and Down-Selection outlined in the ATF Roadmap. This irradiation test series is planned to be performed as a series of drop-in capsule tests to be irradiated in the Advanced Test Reactor (ATR) operated by the Idaho National Laboratory (INL), and it has been designated as the ATF-1 test series. Current fission reactors use zirconium-based fuel cladding because of its extremely low macroscopic thermal neutron absorption cross-section, good high temperature strength, and decent corrosion resistance. However, advanced, innovative materials may provide these same benefits while increasing reactor safety margin, core power density, and fuel utilization. These advanced fuel cladding systems will allow revolutionary cladding performance and enhanced fuel mechanical designs, however, challenges exist in design, analysis and fabrication of innovative, never before tested, fuel cladding systems for in-reactor testing. This paper highlights the challenges associated with design, fabrication and welding, and inspection of innovative materials and actions taken to address those challenges in preparation for the Phase I ATR irradiation testing. The lessons learned from Phase I of this experiment can be used to guide researchers for design and analysis of future in-reactor testing of advanced fuel cladding systems.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Transition Core Planning and Safety Analyses in Support of LEU Fuel Conversion of the University of Missouri Research Reactor (MURR)

The University of Missouri Research Reactor (MURR®) is one of six U.S. High Performance Research Reactors (USHPRR), including one critical facility, that is working with the National Nuclear Security Administration (NNSA) Office of Material Management and Minimization (M3) Reactor Conversion Program to convert from highly enriched uranium (HEU) to low-enriched uranium (LEU) fuel. The M3 Reactor Conversion USHPRR Project objectives include the development of LEU fuel element designs that will ensure safe reactor operations and to maintain the existing experimental performance of each facility. The work is being conducted through many inter-related activities being completed by four Project Pillars: Fuel Qualification (FQ), Fuel Fabrication (FF), Reactor Conversion (RC), and Cross Cutting (CC). A new type of LEU fuel based on an alloy of uranium-10 wt% molybdenum (U-10Mo) is expected to allow the conversion of those USHPRR, like MURR, requiring higher density fuels. The very-high-density LEU U-10Mo monolithic fuel is currently undergoing irradiation testing and post-irradiation examination under a planned and documented fuel qualification effort. The FQ Pillar will document fuel property and fuel performance data and qualify the fuel for use in these reactors. The FF Pillar is fabricating fuel for ongoing and future irradiation tests, as well as conducting fabrication demonstrations to validate or update preliminary fabrication assumptions. The FF Pillar is also working to develop and install commercial manufacturing capacity with the U-10Mo monolithic fuel to produce prototypic fuel. Working with the RC Pillar at Argonne, MURR has progressed through a preliminary fuel element design using preliminary data for the proposed monolithic alloy of U-10Mo. Analyses were completed in previous work that found for typical equilibrium operations with the preliminary LEU fuel element design, in conjunction with a power uprate to 12 MW and appropriate changes to the MURR Limiting safety system settings (LSSS), MURR will have adequate margins to safety for steady-state operations and postulated transient accidents and will have experimental performance in key locations that meets or exceeds current operations with HEU fuel. The purpose of this work is to develop a sequence of transition cycles that will enable MURR to transition from operation with the reactor core loaded with fresh LEU fuel elements only to typical equilibrium operations with mixed-burnup cores following conversion while meeting operational requirements on safety and experimental performance. It is expected that the use of fresh LEU fuel at conversion and subsequent low burnup of the LEU fuel elements that will initially be available for use following conversion will result in critical control blade positions that will substantially change the axial power distribution in the core and the neutron flux available in key experimental locations relative to equilibrium LEU operations. Given the constraints of MURR safety margins, operational practices, and production and research, a novel method has been developed to identify a transition sequence that minimizes the time MURR operates atypically compared to the current prototypic cycles using HEU fuel. The proposed transition sequence moves quickly to the same sort of equilibrium cycles for the LEU fuel that have already been evaluated in documented preliminary safety analyses. Although shifting the neutron flux peak to the lower half of the core during initial cycles with LEU at 12 MW reduces the experiment performance in some key locations relative to current HEU operations at 10 MW, all LEU cores provide an average performance that meets or exceeds that of HEU. An LEU cycle is reached that meets or exceeds the level of experimental performance predicted for current HEU and equilibrium LEU operations in more than 450 key locations identified by a reactor specialist at MURR by the 23rd cycle following conversion and that afterwards will enable MURR to consistently meet its experimental performance requirements. The proposed transition sequence only requires the fabrication of 34 fresh LEU elements in the first year of operation and does not exceed the anticipated availability of fresh elements that can be produced by the fuel fabricator. By the third year after conversion, 22 fresh LEU elements will be required each year, which is the same as expected for equilibrium LEU operations and the same as current operations with HEU fuel. The proposed transition sequence thus combines a relatively short time period before equilibrium burnup is achieved, a temporary increase of fuel elements needed annually relative to typical operations that are within the production capabilities of the fuel fabricator, and demonstrates comparable experimental performance of the LEU cores relative to current HEU operations. Further measures may be taken to reduce any initial experimental performance penalty even further, where possible, by repositioning certain experiments to leverage the increased performance in the lower axial experimental positions in the initial cycles following conversion or leaving the experiments in the irradiation facilities longer in order to achieve the required neutron fluence. This analysis may require refinement depending on the experimental facilities in use at the time of conversion. Nonetheless, the results presented here, including the experimental performance, core burnup, and critical control blade positions throughout the transition cycles, show that the proposed transition cycle fuel management patterns are consistent with what is expected and desired for MURR operation with LEU U-10Mo fuel. Detailed core power distributions from the neutronics models were also used to evaluate safety margins during steady-state operations for the selected transition cycles and the equilibrium LEU core. It is shown that there are adequate safety margins for both steady-state operations and postulated accident scenarios. For the steady-state operations with the preliminary LEU fuel element design the analysis predicts at least 2.49 MW margin to the onset of flow instability at the LSSS power of 15 MW. Considering the LSSS power is 125% of full license power, the margin to OFI is sufficient. In addition, the critical heat flux ratio at LSSS power is well above the requirement of CHFR > 2.0 from NUREG-1537 for all considered cases. For postulated transient accidents, the minimum margin to the fuel temperature safety limit is at least 109 °C. In summary, the proposed sequence of core loadings for MURR operations following conversion to LEU fuel and a power uprate to 12 MW provides sufficient safety margins for both steady-state operations and postulated transient accidents during a proposed sequence of transition cycles to equilibrium operations. Analysis has shown that there are some local experimental performance penalties during the initial cycles. Although there are local shifts in the experimental performance, on average all LEU cores at 12 MW have equal or higher performance than HEU at 10 MW. Temporary adjustments are being planned that will produce suitable experimental performance during these cycles. The results indicate that for the equilibrium LEU core the experimental performance exceeds that of current HEU operations in all key locations while also demonstrating sufficient safety margins.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Comparative Flow Path Analysis and Design Assessment of an Axisymmetric Hydrogen Fueled Scramjet Flight Test Engine at a Mach Number of 6.5

NASA has contracted with the Central Institute of Aviation Motors CIAM to perform a flight test and ground test and provide a scramjet engine for ground test in the United States. The objective of this contract is to obtain ground to flight correlation for a supersonic combustion ramjet (scramjet) engine operating point at a Mach number of 6.5. This paper presents results from a flow path performance and thermal evaluation performed on the design proposed by the CIAM. This study shows that the engine will perform in the scramjet mode for stoichiometric operation at a flight Mach number of 6.5. Thermal assessment of the structure indicates that the combustor cooling liner will provide adequate cooling for a Mach number of 6.5 test condition and that optional material proposed by CIAM for the cowl leading-edge design are required to allow operation with or without a type IV shock-shock interaction.

McClinton, C.↗

An Advanced Integrated Diffusion/Transport Method for the Design, Analysis and Optimization of the Very-High-Temperature Reactors

The main objective of this research is to develop an integrated diffusion/transport (IDT) method to substantially improve the accuracy of nodal diffusion methods for the design and analysis of Very High Temperature Reactors (VHTR). Because of the presence of control rods in the reflector regions in the Pebble Bed Reactor (PBR-VHTR), traditional nodal diffusion methods do not accurately model these regions, within which diffusion theory breaks down in the vicinity of high neutron absorption and steep flux gradients. The IDT method uses a local transport solver based on a new incident flux response expansion method in the controlled nodes. Diffusion theory is used in the rest of the core. This approach improves the accuracy of the core solution by generating transport solutions of controlled nodes while maintaining computational efficiency by using diffusion solutions in nodes where such a treatment is sufficient. The transport method is initially developed and coupled to the reformulated 3-D nodal diffusion model in the CYNOD code for PBR core design and fuel cycle analysis. This method is also extended to the prismatic VHTR. The new method accurately captures transport effects in highly heterogeneous regions with steep flux gradients. The calculations of these nodes with transport theory avoid errors associated with spatial homogenization commonly used in diffusion methods in reactor core simulators

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Fuel Flexible Combustion Systems for High-Efficiency Utilization of Opportunity Fuels in Gas Turbines

The purpose of this program was to develop low-emissions, efficient fuel-flexible combustion technology which enables operation of a given gas turbine on a wider range of opportunity fuels that lie outside of current natural gas-centered fuel specifications. The program encompasses a selection of important, representative fuels of opportunity for gas turbines with widely varying fundamental properties of combustion. The research program covers conceptual and detailed combustor design, fabrication, and testing of retrofitable and/or novel fuel-flexible gas turbine combustor hardware, specifically advanced fuel nozzle technology, at full-scale gas turbine combustor conditions. This project was performed over the period of October 2008 through September 2011 under Cooperative Agreement DE-FC26-08NT05868 for the U.S. Department of Energy/National Energy Technology Laboratory (USDOE/NETL) entitled "Fuel Flexible Combustion Systems for High-Efficiency Utilization of Opportunity Fuels in Gas Turbines". The overall objective of this program was met with great success. GE was able to successfully demonstrate the operability of two fuel-flexible combustion nozzles over a wide range of opportunity fuels at heavy-duty gas turbine conditions while meeting emissions goals. The GE MS6000B ("6B") gas turbine engine was chosen as the target platform for new fuel-flexible premixer development. Comprehensive conceptual design and analysis of new fuel-flexible premixing nozzles were undertaken. Gas turbine cycle models and detailed flow network models of the combustor provide the premixer conditions (temperature, pressure, pressure drops, velocities, and air flow splits) and illustrate the impact of widely varying fuel flow rates on the combustor. Detailed chemical kinetic mechanisms were employed to compare some fundamental combustion characteristics of the target fuels, including flame speeds and lean blow-out behavior. Perfectly premixed combustion experiments were conducted to provide experimental combustion data of our target fuels at gas turbine conditions. Based on an initial assessment of premixer design requirements and challenges, the most promising sub-scale premixer concepts were evaluated both experimentally and computationally. After comprehensive screening tests, two best performing concepts were scaled up for further development. High pressure single nozzle tests were performed with the scaled premixer concepts at target gas turbine conditions with opportunity fuels. Single-digit NOx emissions were demonstrated for syngas fuels. Plasma-assisted pilot technology was demonstrated to enhance ignition capability and provide additional flame stability margin to a standard premixing fuel nozzle. However, the impact of plasma on NOx emissions was observed to be unacceptable given the goals of this program and difficult to avoid.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Preliminary analysis of FCM fuel thermal-mechanical performance under normal and transient conditions

Fully ceramic microencapsulated (FCM) fuel is a candidate fuel form to replace commercial UO{sub 2} fuel rod in LWR to enhance fuel reliability under accident conditions. The FCM pellet consists of TRISO particles embedded inside the dense SiC matrix. This fuel design is more complex than conventional LWR fuel, which needs new fuel performance models or analysis tools to assist fuel design and concept evaluation. In this paper an attempt was made to develop a finite element method to analyze FCM fuel pellet thermal-mechanical performance. Three idealized cases of normal operation, power ramp, and LOCA were analyzed. The results showed that the temperature distribution and stress distribution of FCM pellet exhibited a strong non-uniformity. The irradiation strain and creep of buffer layer and PyC (pyrolytic carbon) layers had a strong effect on the mechanical performance of FCM pellet. The hoop stresses of SiC layers and SiC matrix increased significantly during the LOCA and varied with radial positions. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Neutronics Design of a Thorium-Fueled Fission Blanket for LIFE (Laser Inertial Fusion-based Energy)

The Laser Inertial Fusion-based Energy (LIFE) project at LLNL includes development of hybrid fusion-fission systems for energy generation. These hybrid LIFE engines use high-energy neutrons from laser-based inertial confinement fusion to drive a subcritical blanket of fission fuel that surrounds the fusion chamber. The fission blanket contains TRISO fuel particles packed into pebbles in a flowing bed geometry cooled by a molten salt (flibe). LIFE engines using a thorium fuel cycle provide potential improvements in overall fuel cycle performance and resource utilization compared to using depleted uranium (DU) and may minimize waste repository and proliferation concerns. A preliminary engine design with an initial loading of 40 metric tons of thorium can maintain a power level of 2000 MW{sub th} for about 55 years, at which point the fuel reaches an average burnup level of about 75% FIMA. Acceptable performance was achieved without using any zero-flux environment 'cooling periods' to allow {sup 233}Pa to decay to {sup 233}U; thorium undergoes constant irradiation in this LIFE engine design to minimize proliferation risks and fuel inventory. Vast reductions in end-of-life (EOL) transuranic (TRU) inventories compared to those produced by a similar uranium system suggest reduced proliferation risks. Decay heat generation in discharge fuel appears lower for a thorium LIFE engine than a DU engine but differences in radioactive ingestion hazard are less conclusive. Future efforts on development of thorium-fueled LIFE fission blankets engine development will include design optimization, fuel performance analysis work, and further waste disposal and nonproliferation analyses.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Transient performance of accident tolerant fuel in design basis accidents

A set of transient analysis has been performed to assess the performance of candidate accident tolerant fuel (ATF) against reference UO{sub 2} fuel with Zircaloy cladding under design basis accident (DBA) conditions. This study examined two ATF options, U{sub 3}Si{sub 2} fuel with SiC cladding and UO{sub 2} fuel with APMT cladding. The accident analyses were conducted using the system code TRACE for a three-loop PWR plant. PARCS standalone full-core calculations were done for each fuel/cladding combination to provide inputs to the TRACE point-kinetics model. The design basis accidents analyzed were a reactivity insertion accident (RIA) and a large break loss-of-coolant accident (LBLOCA). The RIA was simulated by the insertion of a reactivity ramp of $1 (one dollar) in 0.1 s at hot full power (HFP) condition. The LBLOCA was a simulation of a double-ended pipe break in one of the cold legs of the primary loops. Differences in thermal responses of the fuel and the cladding are attributed to their thermal properties. The U{sub 3}Si{sub 2} fuel with its lower volumetric heat capacity and higher thermal conductivity (i.e. higher thermal diffusivity) generally results in a lower fuel temperature than the UO{sub 2} fuel and a correspondingly faster thermal response. Additional calculations for the U{sub 3}Si{sub 2} fuel shows that in a RIA the cladding material, SiC versus Zr, has little impact on the maximum fuel centerline temperature and the PCT (peak cladding temperature). An increase in the hot rod power factor is shown to raise the centerline fuel temperature in a RIA but has little impact on the PCT. The analysis results show that for a relatively fast decay heat driven transient, such as the LBLOCA, the thermal-hydraulics and fuel/cladding thermal properties dictate the overall response more so than the reactivity feedback. The results show that the PCTs in a LBLOCA are similar for all fuel/cladding combinations considered in this study. The LBLOCA analysis also notes the impact of the asymmetry in the system response. The fuel rods in the sector of the core connected to the hot leg of the broken loop (Sector 1 in the PWR model) is shown to have a much lower PCT than fuel rods in the other five sectors of the core. Results of this study indicate that for the two DBAs considered (RIA and LBLOCA) the transient behavior and the resulting peak cladding temperature of the two ATF options (U{sub 3}Si{sub 2} fuel with SiC cladding and UO{sub 2} fuel with APMT cladding) are similar to the standard light-water reactor fuel (UO{sub 2} fuel with Zircaloy cladding). (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

BISON: A Flexible Code for Advanced Simulation of the Performance of Multiple Nuclear Fuel Forms

BISON is a nuclear fuel performance application built using the Multiphysics Object-Oriented Simulation Environment (MOOSE) finite element library. One of its major goals is to have a great amount of flexibility in how it is used, including in the types of fuel it can analyze, the geometry of the fuel being modeled, the modeling approach employed, and the dimensionality and size of the models. Fuel forms that can be modeled include standard light water reactor fuel, emerging light water reactor fuels, tri-structural isotropic fuel particles, and metallic fuels. BISON is a platform for research in nuclear fuel performance modeling while simultaneously serving as a tool for the analysis of nuclear fuel designs. Recent research in BISON includes techniques such as the extended finite element method for fuel cracking, exploration of high-burnup light water reactor fuel behavior, swelling behavior of metallic fuels, and central void formation in mixed-oxide fuel. BISON includes integrated documentation for each of its capabilities, follows rigorous software quality assurance procedures, and has a growing set of rigorous verification and validation tests.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Front-End Processes for Conversion of Current HEU-Based Alkaline Processes to LEU Foil Targets: Volumes and Compositions of All Waste, Product, and Off-Gas Streams from Both Front-End Options

The Global Threat Reduction Initiative (GTRI) Conversion Program develops technology necessary to enable the conversion of civilian facilities using high enriched uranium (HEU) to low enriched uranium (LEU) fuels and targets. The main technology components of the program are as follows: • The development of advanced LEU fuels, • Design and safety analysis for research reactor conversion, and • Development of targets and processes for the non-HEU production of the medical isotope molybdenum-99 ( 99 Mo).

Jerden Jr., James L.↗

Contribution of IAEA coordinated research projects to light water reactors advanced technology fuel testing and simulation

The Fukushima-Daiichi accident in 2011 highlighted the pressing need for enhanced design and safety analysis of nuclear fuels, especially under accident conditions in nuclear power plants (NPPs). To address this need, the international nuclear fuel community has developed several concepts of Accident Tolerant and Advanced Technology Fuels (ATFs) for light water reactors. The International Atomic Energy Agency (IAEA), at the request of its Member States, has initiated a series of three Coordinated Research Projects (CRPs) to aid in the development and testing of these ATFs. Further, these projects, known as FUMAC, ACTOF, and ATF-TS, focus on the experimentation and simulation of ATFs under various accident conditions, including design basis accidents and design extension conditions. This paper provides a comprehensive overview of the main activities, as well as the achieved or anticipated results of these three CRPs. The insights and advancements gained from these projects will enable IAEA Member States to further refine nuclear fission technology, thereby contributing to efforts aimed at mitigating climate change.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Design and Analysis of a 250 MW Plate-Fuel Reactor for Nuclear Thermal Propulsion

Nuclear thermal propulsion (NTP) is a viable option for deep space missions due to its high thrust and lightweight system. Promising fuel options considered for the high operating temperature of NTP include graphite composite fuel and tungsten cermet fuel. As there remain uncertainties in the fabrication and performance of these two fuel elements, alternative designs using fuel plates and more typical fuels based on proven nuclear technologies are also being considered. This paper provides a summary of thermal hydraulic and neutronic analyses of the straight-plate fuel assembly design used for a 250 MW NTP core. The summary of technical findings from a series of scoping studies might be useful for future NTP engine designs.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

CORE DESIGN AND NEUTRONIC ANALYSIS OF THE EUROPEAN SODIUM FAST REACTOR WITH METALLIC FUEL

The current ESFR (European Sodium Fast Reactor) design was proposed and in-depth evaluated in the frame of the past ESFR-SMART project. As a follow-up project, the ESFR-SIMPLE has been launched with the aim of challenging the current commercial-size ESFR design in terms of safety features and economic performance. Among the new safety measures to be developed and assessed in ESFR-SIMPLE, the current oxide fuel ESFR design will be challenged by a modified version of the core with metallic fuel. This intends to conclude on what types of benefits can be obtained with high-density fuel, under similar safety and design constraints. In this paper, the designing approach for enabling the use of metallic fuel in the current ESFR core is described and a preliminary neutronic evaluation is carried out. The optimal configuration is established through the optimization of key neutronic parameters aiming at the potential reduction of the plutonium inventory. The resulting core configuration serves as a basis for further safety assessment analyses, which will provide insight into the advantages and drawbacks of the two types of fuels.

Jiménez-Carrascosa, Antonio↗

Design and Analysis of a 250 MW Plate-fuel Reactor for Nuclear Thermal Propulsion

Nuclear thermal propulsion (NTP) system is a viable option for deep space missions considering its high thrust and lightweight. Promising fuel options being considered for the high operating temperature of NTP include the graphite composite fuel and the tungsten cermet fuel. As there remains uncertainties in the fabrication and performance of these two fuel elements, alternative designs using fuel plates and more standard fuels that are based on proven and tested nuclear technologies are being considered. This paper provides a summary of thermal hydraulic and neutronic analyses of the straight fuel plate concept used for a 250 MW NTP core. The summary of technical findings from a series of scoping studies might be useful for the future NTP engine designs.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Nitride Fuel Potential for Power Uprates

This work presents the methodology and current results for design analysis of grid supported pressurized water reactor cores using uranium nitride (UN) fuel in square arrays. Uranium nitride has a higher theoretical density and higher thermal conductivity than uranium oxide, allowing for lower fuel temperatures, longer cycle length and higher power densities with similar enrichment. In order to avoid the UN and high temperature water reaction, silicon carbide cladding has been proposed in place of Zircaloy cladding. The analysis aims at finding the maximum thermal power over a range of bundle geometries (rod diameter and pitch). The same methodology is applied to the design of UO{sub 2} oxide fueled cores to provide a fair comparison of the achievable power rating between the two fuel types. Steady-state limits are considered, including fuel bundle pressure drop, minimum departure from nucleate boiling ratio (MDNBR), fuel temperature, fuel rod vibrations and pin fretting and sliding wear. Transients such as loss of flow and overpower accident will be considered. A steady state analysis was undertaken to determine the maximum achievable power that can be sustained by square array fuel assemblies loaded with nitride and oxide fuels with same or better safety performances as the reference design. Steady-state design limits were applied including MDNBR, fuel bundle pressure drop, fuel temperature, cumulative sliding and fretting wear. The major conclusions of this study are as follows: 1) It is possible to achieve significant power increase for UN and UO{sub 2} compared to the reference core power output of 3400 MWth with smaller but more numerous rods and higher pitch over diameter ratios. A power uprate of 25% can be reached according to the VIPRE-MATLAB interface for full core analysis with the same number of spacer grids, and 32% according to the new MATLAB script for single hot channel analysis, with five more spacer grids. For this latter core, a higher enrichment would be required. 2) The nitride fuel temperature constraint from dissociation doesn't influence steady state performances as other design constraints such as MDNBR and pressure loss are more restrictive. The oxide fuel temperature constraint from fission gas release is reached in part of the study domain, but not in the region that allows for possible uprates. 3) As a result, the thermal hydraulic performance of UN and UO{sub 2} are similar. Differences in possible power uprates will arise from fretting and sliding wear. Wear depends of the time spent by the fuel in the core, which depends on burnup and heavy metal inventory. UN being denser, it can allow for power uprates or increased cycle length. There is a trade off between power uprates and cycle length with regards to fuel pin wear. Reducing fuel pin wear by reducing cycle length can allow for higher thermal power. This affects the plants' economics as well. This work will be completed by a transient analysis using CASMO4E, SIMULATE3 and SIMULATE3k to model the neutronics of a nitride fueled core. The transient performances will be used to determine the maximum power uprates while performing as well or better during transients as the reference design. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗