Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fuels - Relation to Engine Performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Mechanistic Fission Gas Release Uncertainty Induced by Microstructure Data

Fission Gas Release (FGR) is an important engineering safety parameter for nuclear fuel. While fuel performance modeling with BISON currently relies on mechanistic models to predict it, comparison with experimental data shows both under or over prediction depending on operation mode (steady or transient).Predicting microstructure data is essential to accurately predicts the engineering scale parameters. An important source of uncertainty in mechanistic models arises from the missing captured physics. Continuous validation and refinement of these models against experimental data are also necessary to ensure their reliability and accuracy in predicting engineering parameters.

36 - MATERIALS SCIENCE↗
DOE OSTI2022

Environmental, Economic, and Scalability Consideration of Selected Biomass-Derived Blendstocks for Mixing-Controlled Compression Ignition (MCCI) Engines

Co-Optimization of Fuels & Engines (Co-Optima) explores how simultaneous innovations in fuels and engines can boost fuel economy and vehicle performance while reducing emissions. The Analysis of Sustainability, Scale, Economics, Risk and Trade (ASSERT) team supports Co-Optima goals by evaluating environmental and economic drivers and the potential of bioblendstock candidates. The team assesses potential benefits or drawbacks of deploying co-optimized fuels and engines in the transportation sector. This presentation provides guidance into which Co-Optima bioblendstocks may be most economically and environmentally viable when scaled up.

biomass↗
DOE OSTI2021

Transverse Rupture Strength of Uranium Dioxide

Uranium dioxide (UO 2 ) fuel is used as fuel in light water reactors (LWRs). While the fuel pellet is technically the first engineering barrier for radionuclide release, pellet fracturing at intermediate- to high-burnup values releases fission gases into the fuel rod plenum [1, 2]. Therefore, the true engineering barrier is the fuel cladding, which performs very well in LWR environments [3]. The extreme temperature gradients generated by fission energy and the low thermal conductivity of UO 2 quickly induce radial cracking in UO 2 during operation [4]. Cracks in the fuel provide opportunities for fuel relocation, increased fission gas release, and pellet-cladding mechanical interaction (PCMI) [5]. The ability to predict and engineer the fracture of UO 2 fuel pellets using modern computational tools is therefore a key engineering goal that has been the focus of ongoing experimental and computational efforts [6, 7]. Accurate predictions of fuel pellet cracking during operation requires knowledge of more complex phenomena, but improved understanding of the fundamental fracture behavior of unirradiated UO 2 is first necessary.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Effective Lanthanide Diffusivity through U-Zr Metallic Fuel

Fuel-cladding chemical interaction (FCCI) is one of the main concerns for the performance of U-Zr metallic fuels. Although FCCI results in complex phase transformations and morphological changes in both the fuel and cladding sides of the interface, the formation of a brittle layer in the cladding side of the interface (sometimes referred to as wastage) has one of the most significant impacts on the cladding mechanical integrity. This brittle layer is associated with the formation of intermetallic compounds between the cladding constituents Fe, Cr and the lanthanide fission product species. The formation of this cladding wastage layer has been the focus of recent efforts to develop a mechanistic modeling framework, including production of lanthanides in the fuel, transport through the fuel to the fuel-cladding interface, and phase transformation to form intermetallic phases. To calculate the rate of transport of lanthanides through the fuel, a multi-scale computational approach has been used. Atomistic calculations have been performed to determine the diffusivities of Nd, the most prevalent lanthanide species, through the solid fuel matrix and along pore surfaces. These diffusivities have been used as input parameters for a mesoscale model to determine an effective diffusion coefficient that accounts for the formation of porosity, its interconnection, and infiltration with bond sodium from the fuel-cladding gap. The effective diffusivity has been used in engineering-scale simulations using the BISON fuel performance code, and BISON simulations have been compared to representative validation cases from the EBR-II reactor.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Multi-scale modeling of wastage layer formation in metallic fuel cladding

Fuel-cladding chemical interaction (FCCI) is a major concern for U-Zr metallic fuels' performance, primarily due to the formation of a brittle layer (wastage) in the cladding. This brittle layer, resulting from intermetallic compounds between cladding constituents Fe, Cr, and lanthanide fission products, significantly impacts the cladding's mechanical integrity. Recent efforts focus on developing a mechanistic modeling framework to understand lanthanide production, transport to the fuel-cladding interface, and phase transformation to intermetallic phases. A multi-scale computational approach has been used to calculate lanthanide transport rates, with atomistic calculations determining Nd diffusivities through the solid fuel matrix and along pore surfaces. These diffusivities inform a mesoscale model to determine an effective diffusion coefficient, accounting for porosity and infiltration with bond sodium. This effective diffusivity is used in engineering-scale simulations via the BISON fuel performance code, which has been validated against EBR-II and FFTF reactor experiments.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

AN EXPERIMENTAL STUDY OF FUEL SELECTION FOR A GASOLINE MULTI-MODE

In this study of fuels of different reactivities and their performance in a low-temperature combustion (LTC) engine. The engine was a 2.2L CRDI engine code D4HB provided by industry partner Hyundai America Technical Center inc. (HATCI). The engine was instrumented with in-cylinder pressure sensors allowing for monitoring of the combustion process. First, the engine was operated with standard US pump grade gasoline, Research Octane number (RON) 91 E10, to find initial operation conditions as well as control points of stable operation for daily checks on system conditions. Tested were 8 different fuel blends, the four base blends were provided by Phillips 66 (P66) with a RON value ranging from 60 to 91, and three other variations of these fuels were formulated by splash blending alcohols, iso-butanol, and ethanol, with the RON60 fuel and the final blend, was US RON91 E10 pump gasoline. Using these 8 fuels, the low load performance was analyzed allowing a selection of one of the fuels to be made to proceed with experimentation. To study the low load performance of each fuel, the load was decreased until combustion became too unstable to continue. This was done at 1500 rpm with all of the fuels. At 1200 rpm, the same methodology was applied, though all of the fuels were not tested, only the fuels which showed promise at 1500 rpm. Meaning that the lowest targeted load was achieved without any aid to the combustion process other than advancing combustion, increasing intake air temperature (IAT) for example was not done to maintain consistency across all fuels. The same methodology was applied at 800 rpm based upon the 1200 rpm results to see the ability of the engine to idle with the given fuel. It was found that fuel with a RON of 80 showed good low load performance while allowing for high load performance to be maintained. A blend of 25% Iso-Butanol and 75% RON 60 equated to a RON of 80 and showed good low load performance and showed peak indicated thermal efficiency (ITE) numbers of 46% at 17 bar indicated mean effective pressure (IMEP) and 2200 rpm.

02 PETROLEUM↗
DOE OSTI2020

A detailed chemical kinetic modeling and experimental investigation of the low- and high-temperature chemistry of n-butylcyclohexane

Chemical kinetic models of gasoline, jet, and diesel fuels and their mixtures with bioderived fuels are needed to assess fuel property effects on efficiency, emissions, and other performance metrics in internal combustion and gas turbine engines. As these real fuels have too many fuel components to be included in a chemical kinetic model, surrogate fuels containing fewer components are used to represent them. These surrogate fuels mimic the chemical classes or molecular structures contained in the real fuel. One of the important chemical classes in gasoline, jet, and diesel fuels comprises cyclohexanes. Cyclohexanes comprise about 30% or more by weight in diesel fuel. Also, Mueller et al proposed n-butylcyclohexane (nBCH) as a component in a nine-component surrogate palette to represent the ignition properties, distillation curve, density, and molecular structures of a diesel certification fuel. Herein, experimental measurements of the ignition delay times (IDTs) of nBCH in a shock tube and in a rapid compression machine are reported over a wide range of temperature, pressure, and equivalence ratio important for enabling the validation of a chemical kinetic model for nBCH for combustion in diesel engines. The range of conditions are temperatures of 630–1420 K, pressures of 10, 30, and 50 bar, and equivalence ratios of 0.3, 0.5, 1.0, and 2.0 in ‘air’. A detailed chemical model is developed for nBCH to simulate its ignition at both low and high-temperature conditions and at relevant elevated pressures. The experimentally measured IDTs are used to improve and validate the chemical kinetic model.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Spray and combustion characteristics of pure hydrothermal liquefaction biofuel and mixture blends with diesel

Hydrothermal liquefaction (HTL) is the process in which biological compounds can be converted into biocrude diesel; various feedstocks, such as algae and wet biowaste, can be utilized. Almost 20 million dry tons of wet biowaste is deposited in U.S. municipal wastewaters annually. If recovered and converted into biodiesel, it can act as a massive source of renewable energy. Preliminary experiments on a diesel engine show that HTL fuel can achieve similar performance and emission levels to diesel. In order to further understand the influence of the HTL fuel properties, the HTL fuel and blends with diesel are observed in a constant volume chamber. Previously, 10% and 20% of the HTL fuel were blended with diesel by volume and demonstrated properties that roughly matched diesel in terms of combustion. In this study, 50% and 100% HTL fuel blends are tested on the same apparatus. It was discovered that the workability of HTL is almost the same as that of diesel and is less sensitive to ambient temperatures. When the ambient temperature is reduced from 1200 K to 800 K, the change ratio of ignition delay is only 62% of diesel. By analyzing the combustion process, it can be seen that there is no need to make major modifications to the engine control strategy if HTL fuel is applied to diesel engines. Though, under low temperature and low oxygen conditions, the soot luminosity peak of HTL100 is 3.12 times than that of diesel.

09 BIOMASS FUELS↗
DOE OSTI2021

Fuel Properties and Kinetics

The Co-Optimization of Fuels and Engines (CoOptima) program is focused on a two-pronged approach to develop new, lower net-carbon fuels and advanced engine technologies in tandem. This effort brings nine national labs and several university and industry partners together to simultaneously identify new fuel candidates and to further engine technology development in the light-, medium-, and heavy-duty vehicle sectors with a focus on fuel economy and emission reduction. The fuel properties and kinetics project is aimed at achieving a better understanding of fuel property kinetics and how they impact engine performance such that more efficient and lower emitting engines can be made a reality. Several promising biofuel candidates were identified through tiered screening approaches and were evaluated utilizing unique bench-scale measurement techniques. Kinetic models were developed to describe autoignition and soot pre-cursor formation mechanisms to identify the most promising candidates that advanced various combustion strategies.

ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Ducted Fuel Injection And Cooled Spray Technologies For Particulate Control In Heavy-duty Diesel Engines (Final Report)

Cooled Spray (CS) and Ducted Fuel Injection (DFI) are in-cylinder technologies for diesel engines that can reduce particulate matter and soot emissions and data has been published showing that these technologies can reduce soot emissions by 75-100% for some engines at some operating conditions. However, little is known about scaling the devices for engine size. Additionally, the performance of either technology over the engine duty cycle has not been explored. This project addresses both of these points through single-cylinder engine investigations. The objectives of this project are to provide details about dimensional scaling of these devices and to demonstrate 75% PM reduction over a range of operating conditions on a single-cylinder engine. Two engines were used for this project: a 125mm bore optically accessible engine at Sandia National Laboratories and a 168mm bore metal engine at Southwest Research Institute. The optical engine was used to study the performance of DFI and CS inserts for a large injector orifice diameter injector that is characteristic of a locomotive engine and to perform scaling studies for DFI. The metal engine was used to perform scaling and alignment studies for CS and to evaluate the technology for both EGR and non-EGR engines over the engine operating map. Modifications were required for both engines to accept the prototype inserts being tested. The optical engine required a new fuel injector, cylinder head and piston so that tests could be run at the pressures and engine speeds required. Additionally, a novel rotating stage was designed for the optical engine to simplify alignment of the modules. The metal engine required a modified cylinder head to accept CS inserts and a modified piston to provide additional space around the fuel injector for the CS inserts. Tests on the optical engine showed that DFI reduces PM emissions for both small injector orifices (0.170mm diameter) and large injector orifices (0.290mm). For high load testing, the DFI modules were not as effective as at low load testing, but it was acknowledged that minimal geometric optimization was performed and more improvements may be possible. Comparing DFI to CS and conventional diesel combustion (CDC), DFI performed better than CS or CDC. The CS geometries used in these studies may not be ideal for that engine and additional modifications likely would improve performance. Tests on the metal engine showed PM reductions as high has 80% at some operating conditions with duty-cycle PM reductions of ~50% for EGR and non-EGR configurations. The CS testing on the metal engine showed that chamfering of the fuel passage inlet either through hydro-erosion or mechanical grinding provided significant improvements in the PM reduction capabilities of the insert. Additionally, alignment sensitivities were explored and the data show that the tolerance to misalignment is approximately 0.05 to 0.1mm for the inserts that were studied here. Air-fuel ratio was shown to be important in the effectiveness of the CS inserts. In several tests, it was shown that the CS inserts are more effective at reducing the PM for high-AFR operating conditions compared to low AFR conditions. In summary, multiple designs were evaluated on both engines. It was found that for the conditions and configurations studied here, a fuel passage diameter of ~2.5mm performed best overall. Significant duty-cycle PM reductions are possible using these technologies and sensitivities to AFR, alignment fuel passage diameter and inlet fuel passage shaping were explored and are reported here. More PM reduction may be possible with improved geometric design and attention to alignment practices.

02 PETROLEUM↗
DOE OSTI2020

Data-Driven Model Reduction of Multiphase Flow in a Single-Hole Automotive Injector

Fuel injector design has a substantial influence on the performance and emissions of direct injection engines. To date, large eddy simulations coupled with a single-fluidmixture modeling approach have shown great success in evaluating the complex interplay among injector design, fuel properties, and operating conditions on the injector performance. However, this simulation approach is too computationally expensive to be used by industry routinely for injector design due to the fine temporal and spatial resolution required to resolve wall-bounded flow within the injector. The work presented in this paper highlights a potential pathway to addressing this issue. To study the influence of injector design, fuel properties, and operating conditions on injector performance, large eddy simulations were performed to model the turbulent multiphase flow development through a side-oriented singlehole diesel injector. Using Latin hypercube sampling, the design space spanning a range of fuel properties, operating conditions, and needle lifts were explored. Two techniques for dimensionality reduction, namely proper orthogonal decomposition and autoencoders, were compared to evaluate their accuracy in representing the flow in a reduced dimensional space. Finally, based on the findings from this work, recommendations are provided in using machine learning approaches within the context of emulation to construct reduced-ordermodels for internal flow development relevant to automotive applications.

42 ENGINEERING↗
DOE OSTI2026

Fuel Performance Modeling Internship Final Presentation

This study examines the performance of U-Zr and U-Pd-Zr annular metallic fuel rodlets and details the current status of modeling efforts regarding U-Pu-Zr solid metallic fuel rodlets which were experimentally evaluated as part of the Advanced Fuels Campaign (AFC). The AFC mission is to develop novel fuel technologies and facilitate the implementation of those technologies by industry partners. A key objective is to improve steady-state and transient performance over current fuel types. The experiments of interest in this study included metallic fuel rodlets within HT-9 cladding which were placed in SS-316 capsules and inserted in the Advanced Test Reactor (ATR). Certain mechanical and thermal conditions cannot be directly evaluated through experiments and fuel performance modeling is used to shed light on this evolution over time. In this study, BISON Multiphysics simulations are leveraged to investigate the state of the fuel system throughout and after the experimental conditions.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Fabrication and characterization of nanoscale magnesium diboride and tetraboride for propulsion and hydrogen storage applications

Abstract: Boron-loaded propellants have the potential to dramatically increase the performance of solid fuel ramjets, ducted rockets, and hybrid rocket engines. However, difficult ignition of boron decreases the combustion efficiency of these propellants. One approach to solving this problem involves the use of magnesium diboride, MgB2, which ignites easier than boron. Magnesium tetraboride, MgB4, potentially offers greater energetic performance as B has a higher energy density than Mg. However, the effect of the higher boron/metal ratio on the ignition and combustion is unclear. Nanoscale MgB2 particles and quasi 2D structures are promising propellant ingredients, but the oxidation and combustion properties of nanoscale MgB4 remain unknown. Nanoscale magnesium borides are also of interest as precursors for the synthesis of magnesium borohydride, Mg(BH4)2, a promising hydrogen storage material, but hydrogenation of MgB4 has not been studied yet. The objectives of the present work included synthesis, purification, and high-energy ball milling of MgB2 and MgB4 powders as well as investigation of their hydrogen uptake, thermal decomposition, oxidation, and combustion. The powders were fabricated by combustion synthesis and by heating in a tube furnace. The latter method was superior in the synthesis of MgB4. Oxide impurities in the synthesized powders were removed by acid leaching. Nanoscale powders were obtained by ball-mill exfoliation. The hydrogen intake of the obtained magnesium borides was examined at 700 bar and 300 ℃ and did not reveal any advantage of MgB4 over MgB2. Their thermal decomposition and oxidation were investigated with thermogravimetric analysis (TGA), while their combustion was studied using laser ignition and high-speed video recording. TGA has confirmed prior observations of multistep decomposition of magnesium borides, where each step involves formation of a boride with a higher B/Mg ratio and evaporation of formed magnesium. The oxidation rates of the borides are much higher than that of boron at temperatures over 1200 °C for MgB2 and over 900 °C for MgB4. The burning rates of non-milled MgB₂ and MgB₄ powders were much higher than for the used submicron boron. Milling the MgB₂ and MgB₄ powders further increased their burning rates. The milled MgB4 burned 7.5 times faster than submicron boron.

Combustion of metals, Solid fuels, Propellants, Hy↗
DOE OSTI2021

A Rapid Compression Machine Study of 2-Phenylethanol Autoignition at Low-To-Intermediate Temperatures

To meet the increasing anti-knocking quality demand of boosted spark-ignition engines, fuel additives are considered an effective approach to tailor fuel properties for satisfying the performance requirements. Thus, screening/developing bio-derived fuel additives that are best-suited for advanced spark-ignition engines has become a significant task. 2-Phenylethanol (2-PE) is an attractive candidate that features high research octane number, high octane sensitivity, low vapor pressure, and high energy density. Recognizing that the low temperature autoignition chemistry of 2-PE is not well understood and the need for fundamental experimental data at engine-relevant conditions, rapid compression machine (RCM) experiments are therefore conducted herein to measure ignition delay times (IDTs) of 2-PE in air over a wide range of conditions to fill this fundamental void. These newly acquired IDT data at low-to-intermediated temperatures, equivalence ratios of 0.35–1.5, and compressed pressures of 10–40 bar are then used to validate the 2-PE model developed by Shankar et al. (2017). It is found that this literature model greatly overpredicts the current RCM data. The comparison of experimental and simulated results also provides insights into 2-PE autoignition behaviors at varying conditions. Further chemical kinetic analyses demonstrate that the absence of the O2-addition pathway of β-R. radical in the 2-PE model of Shankar et al. (2017) could account for the model discrepancies observed at low-to-intermediated temperatures.

Fang, Ruozhou (ORCID:0000000348315100)↗
DOE OSTI2024

The Case for Reducing Emissions from Heavy-Duty Off-Road Applications via Ducted Fuel Injection

Designers of heavy-duty diesel engines use a variety of techniques to improve efficiency and reduce pollutant emissions. Ducted fuel injection (DFI), high fuel injection pressures, optimized injection orifices, multiple injection sites, and oxygenated fuels are a few techniques used by designers to improve fuel/charge-gas mixtures within the combustion chamber to improve efficiency and emissions results. Ducted fuel injection (DFI) has been proven to substantially reduce soot for low- and mid-load conditions in heavy duty engines, without significantly increasing nitrogen oxides (NO x ). This study investigates the performance of DFI utilizing conventional diesel fuel and the potential the technique has for future research utilizing varieties of test fuels and operating parameter values. Optimization for high engine efficiency and low emissions will help facilitate DFI deployment for substantial environmental benefits in heavy-duty sectors where electrification and/or carbon-free fuels aren’t feasible.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2026

AOI 5 Improved Efficiency of Medium- and Heavy-Duty Natural Gas and Propane (LPG) Engines

Spark-ignited heavy-duty (HD) natural gas engines typically experience efficiency losses at part-load operation due to throttling requirements needed to maintain stoichiometric combustion. A substantial portion of medium- and heavy-duty engine operation occurs in this low-load region, resulting in increased brake-specific carbon dioxide emissions and reduced overall efficiency. This project designed, developed and demonstrated cylinder deactivation (CDA) technology on an HD natural gas engine to mitigate these losses. CDA enables selective deactivation of cylinders, reducing pumping losses while maintaining required torque output and meeting vehicle noise, vibration, and harshness (NVH) targets. The project objectives were successfully achieved, demonstrating up to 12% improvement in fuel consumption over the next generation HD NG engine on key low loaded HD cycles and maintained compliance with 0.02 g/hp-hr NO x emissions with comparable or better vibrations to current product. These results confirm that CDA technology can substantially improve the fuel efficiency and environmental performance of heavy-duty natural gas engines, reinforcing their potential as a low-carbon bridge solution in the transition toward zero-emission transportation technologies.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗