Liquid oxygen seal investigation status report
Fluorocarbon plastic materials for liquid oxygen seal gasket - Saturn launch vehicle
FLUOROCARBON↗
SEARCH · Search NASA
Results for “GASKET”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Cyclic strain induced creep - A separable connector design problem
Cyclic loading induced creep in metals for connector gaskets
CONNECTOR↗
Cryogenic Flange and Seal Evaluation
The assembly of flanges, seals, and pipes are used to carry cryogenic fluid from a storage tank to the vehicle at launch sites. However, after a certain amount of cycles these raised face flanges with glass-filled Teflon gaskets have been found to have torque relaxation and are as a result susceptible to cryogenic fluid leakage if not re-torqued. The intent of this project is to identify alternate combinations of flanges and seals which may improve thermal cycle performance and decrease re-torque requirements. The general approach is to design a test fixture to evaluate leak characteristics between spiral and concentric serrations and to test alternate flange and seal combinations. Due to insufficient time, it was not possible to evaluate these different types of combinations for the combination that improved thermal cycle performance the most. However, the necessary drawings for the test fixture were designed and assembled along with the collection of the necessary parts.
fluid↗
Measuring very low radiation doses in PTFE for nuclear forensic enrichment reconstruction
Every country that has made nuclear weapons has used uranium enrichment to do so. Despite the centrality of this technology to international security, there is still no reliable physical marker of past enrichment in the open literature that can be used to perform forensic verification of historically produced weapons on gas centrifuges. We show that the extremely low radioactivity from uranium alpha emissions during enrichment leaves detectable and irreversible calorimetric signatures in the common enrichment gasket material PTFE, allowing for historical reconstruction of past enrichment activities at a sensitivity better than one weapon’s quantity of highly enriched uranium. Fast scanning calorimetry also enables the measurement of recrystallization enthalpies of sequentially microtomed slices, confirming the magnitude and the type of radiation exposure while also providing detection of tampering and a method for analyzing field samples useful for treaty verification. Furthermore, this work opens the door for common items to be turned into precise dosimeters to detect the past presence of radioactivity, nuclear materials, and related activities with high confidence.
98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗
Materials Engineering for High Performance and Durability Proton Exchange Membrane Water Electrolyzers
Proton exchange membrane water electrolyzers (PEMWEs) are expected to play a crucial role in the global green energy transition during the 21st century. They provide a versatile and sustainable solution for generating hydrogen with very high purity in combination with renewable energies, such as solar and wind. Despite their promise, PEMWEs face several critical problems, including high costs, performance limitations, and durability challenges, particularly at low iridium (Ir) loading on the anode. Advancing next-generation PEMWEs requires extensive work on materials engineering of all cell components, including the catalyst layer (CL), membrane, porous transport layer (PTL), bipolar plate (BPP), and gasket. This task must be performed with the complementary contribution of different modeling and characterization techniques. This review presents a critical perspective from academia, research centers, and industry, mapping main developments, remaining gaps, and strategic pathways to advance PEMWE technology. A focus is devoted to key aspects, such as operation at low Ir loading, membrane durability, multiscale transport layers, porous and non-porous flow fields, multiphysics modeling, and multipurpose characterization techniques, which are thoroughly discussed. By unifying these topics, this review provides readers with the essential knowledge to grasp current developments and tackle tomorrow's challenges in PEMWE engineering.
36 MATERIALS SCIENCE↗
An Interfacial Engineering Approach toward Operation of a Porous Solid Electrolyte CO 2 Electrolyzer
Waste CO 2 can be repurposed as a carbon feedstock for synthesizing valuable chemicals via CO 2 electrolysis. Porous solid electrolyte (PSE) CO 2 electrolysis has been demonstrated as an economically viable method to produce high purity products. This work applies an interfacial engineering approach to determine key factors to improve performance in PSE CO 2 electrolyzers. We standardize the assembly by binding the ionic resin into an ionomer wafer and utilize Computational Fluid Dynamics (CFD) to design gaskets for uniform fluid flow. Here, we employ the distribution of relaxation times (DRT) method to determine that anionic-conducting interfaces are the primary contributor to energy losses. To address this, we demonstrate that enhancing the contact between the cathode and the anion exchange membrane (AEM) and the AEM-ionic resin interface allows for low overpotential in deionized water operation.
09 BIOMASS FUELS↗
Magnetometry in a diamond anvil cell using nitrogen vacancy centers in a nanodiamond ensemble
The emerging field of optical magnetometry utilizing negative-charged nitrogen vacancy (NV – ) centers provides a highly sensitive lab bench technique for spatially resolved physical property measurements. Their implementation in high pressure diamond anvil cell (DAC) environments will become common as other techniques are often limited due to the spatial constraints of the sample chamber. Apparatus and techniques are described here permitting for more general use of magnetic field measurements inside a DAC using continuous wave optical detected magnetic resonance in NV – centers in a layer of nanodiamonds. A microstrip antenna delivers a uniform microwave field to the DAC and is compatible with simple metal gaskets, and the sensor layer of deposited nanodiamonds allows for simple determination of the magnetic field magnitude for B in the 1–100 G range. The ferromagnetic transition in iron at 18 GPa is measured with the apparatus, along with its hysteretic response.
75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
Raman scattering of rhenium for secondary pressure calibration
With the increasing number of 100 s GPa experiments in the diamond anvil cell (DAC), improved accuracy in secondary pressure calibrations to extreme pressures is essential. The rhenium equation of state has been proposed as a pressure calibrant via x-ray diffraction with potentially broad applications as it is commonly used as a gasket material in DAC experiments. In this work, we conducted Raman spectroscopy experiments on rhenium in the DAC and report the pressure shift of the E2g mode, a refined high-pressure C44 and mode-Grüneisen parameter above 200 GPa. We used flat, beveled, and toroidal diamond anvils under quasi-hydrostatic and non-hydrostatic conditions. By measuring the E2g mode from the culet edge to the center, we analyzed pressure distribution based on culet type and distance from the anvil center. The shift in the E2g mode can be expressed as a function of pressure, and diamond edge measurements appear reliable across all anvil types. Comparing the center and edge pressures reveals anvil cupping, offering insights into predicting or preventing anvil failure during materials properties measurements at extreme conditions.
Diamond anvil cells↗
Experimental and computational studies on high-entropy carbide MoNbTaVWC 5 under high pressures
High-entropy carbide, MoNbTaVWC 5 , was synthesized from oxide precursors of the constituent metals, mixed with graphite powder in a microwave-generated hydrogen plasma at 26.66 kPa and 2100 °C. Ambient x-ray diffraction analysis confirms the full conversion of oxide precursors into a single-phase, face-centered cubic structure with a lattice parameter a = 4.3309 Å. Nanoindentation measured a hardness of 24.5 ± 1.3 GPa and an elastic modulus of 386 ± 22 GPa. The synthesized sample, mixed with a copper pressure marker, was studied by the radial x-ray diffraction technique with beryllium gasketing in a diamond anvil cell up to 70 GPa. The experimentally measured pressure–volume curve and shear strength were compared with theoretical predictions using the special quasi-random structure technique and density functional theory. MoNbTaVWC 5 achieved a 12% volume compression at 70 GPa and exhibited a high shear strength of 6.6 GPa. The present study demonstrates that the high-entropy carbide MoNbTaVWC 5 exhibits exceptional incompressibility and high strength under extreme conditions.
36 MATERIALS SCIENCE↗
Effect of pressure cycling and compression rate on the bcc-hcp transition in an FeNi alloy
Here, we investigate the body-centered cubic (bcc) to hexagonal close-packed (hcp) phase transition in Fe-10wt. %Ni alloy, combining pressure cycling and fast compression with time-resolved synchrotron x-ray diffraction in a dynamic diamond anvil cell. Three pressure cycles were conducted with compression rates ranging from 0.1 to nearly 10 3 GPa/s. During the first cycle with the slowest compression, the observed orientations in the bcc and hcp phases are consistent with the Burgers mechanism, followed by c-axis rotation of the hcp phase consistent with {$10$ $\bar{1}2$} twinning. During the following cycles with fast compression at 10 2 –10 3 GPa/s, the hcp phase exhibits negligible c-axis rotation with a nearly constant c/a ratio of ∼1.61 up to ∼30 GPa, indicating suppression of plastic deformation (especially, twinning) due to sample confinement from the gasket. Notably, the onset pressure of the transition decreases with additional pressure cycling and faster compression, which normally leads to over-pressurization. This suggests that defects or shear induced from the pressure cycling reduces the transition kinetics even during fast compression. These insights into the deformation and transition behavior in an FeNi alloy under multiple dynamic loading cycles can offer guidance for future design of advanced structural alloys and improve our understanding of planetary core processes.
FeNi alloy↗
Elastic properties of the W 0.75 R e 0.25 alloy at high pressure up to 183 GPa
The high pressure equation of state for the W 0.75 R e 0.25 alloy is experimentally determined up to 183 GPa with synchrotron angle-dispersive powder x-ray diffraction in the diamond-anvil cell and to ∼925 GPa with density-functional theory. W-Re alloys are used in many industrial high-temperature applications and as a confining gasket material in high-pressure diamond-anvil cell research. The inclusion of 25 wt. % Re achieves the highest performance in terms of strength and ductility while also maintaining the body-centered-cubic (bcc) crystal structure, yet to date there has been no investigation into its elastic behavior at high pressure. We present the experimentally and theoretically determined volumetric and elastic pressure response and systematically compare these results to other W-Re alloys, finding that the bulk modulus of W-Re alloys varies nonlinearly with Re content and W 0.75 Re 0.25 becomes less incompressible than W at 85 GPa. Published by the American Physical Society 2025
Alloys↗
STUDIES ON PIPELINE POLYETHYLENES IN HYDROGEN GAS ENVIRONMENTS USING IN-SITU AND EX-SITU CHARACTERIZATION METHODS
Polymeric materials are commonplace in the natural gas infrastructure as distribution pipes, coatings, seals, and gaskets. Under the auspices of the U.S. Department of Energy HyBlend program, one of the means to reduce greenhouse gas emissions is with replacing natural gas, either partially or completely, with hydrogen. This approach makes it imperative that we conduct near-term and long-term materials compatibility research in these relevant environments. Insights into the effects of hydrogen and hydrogen gas blends on polymer integrity can be gained through both ex-situ and in-situ analytical methods. Our work represented here highlights a study of the behavior of pipeline polyethylene (PE) materials, including HDPE (Dow 2490 and GDB50) and MDPE (Ineos and legacy Dupont Aldyl A), when exposed to hydrogen by means of in-situ X-ray scattering and ex-situ Raman spectroscopy techniques. Samples were tested in ex-situ hydrogen and argon gas environments and in-situ hydrogen environments to identify differences due to permeation and solubility of these gases. These methods complemented each other because Raman spectroscopy could capture permanent effects after materials were removed from gaseous environments, and in-situ X-ray scattering analysis collected real-time data to elucidate the impact of the gas environment on polymer microstructure. Data collected revealed that the aforementioned polymers did not show significant changes in crystallinity and microstructure under the exposure conditions tested. Our findings from these studies will help establish real-time effects caused by hydrogen gas transport through pipeline polyethylenes by way of its influence on polymer structure and chemistry, which is directly related to pipeline mechanical strength and longevity of service.
Hydrogen materials compatibility, Natural gas pipe↗
Negative linear compressibility and complex phase behaviour in 7Li2CO3
High pressure data collected from polycrystalline isotopically enriched 7Li2CO3 using the Paris-Edinburgh press on the SNAP diffractometer. Single toroidal cBN anvils were used with a TiZr gasket. The sample was measured with and without a pressure medium.
high pressure↗
Ice-slurry production for solar-ice systems using supercooling with an in-stream crystallizer
Using ice slurry produced from supercooled water with an in-stream crystallizer opens a new path for solarice systems, increasing efficiency and reducing investment cost compared to ice-on-coil systems. Power needs are decoupled from the stored energy since the heat exchangers are not evenly distributed in the ice storage vessel but directly placed as the heat pump evaporator, which depends on the heat pump capacity and not on the ice storage volume. The novel ice storage design can serve as a heat source for a heat pump, where its evaporator is used to supercool water below 0 °C, or for refrigeration. The supercooled water at a temperature around −2 °C, maintained in a meta-stable liquid state, is triggered to nucleate in an in-stream crystallizer. The current design of the ice crystallizer allows for continuous operation of the system and scalability. Experimental results obtained with a gasketed plate heat exchanger used to supercool water and an in-stream crystallizer operated at a power of up to 6.5 kW are presented.
Thamm, Ann-Katrin↗
SMR Containment Cable and Electrical Penetration Assembly System
GAIN Project CRADA Number NFE-21-08839, entitled “SMR Containment Cable and EPA System” was initiated by the partnership of Oak Ridge National Laboratory (ORNL) and Engineered Solutions Group (ESG) to test an ESG-designed Electrical Penetration Assembly and Containment Cabling System Qualified for not only SMR technologies, but also Advanced Reactors design. An Electrical Penetration Assembly (EPA) is a component used to allow electrical power and signal conductors as well as optical fiber through the nuclear reactor’s containment structure while maintaining a pressure barrier. The EPA ensures the containment's integrity both during the normal operation and also accident conditions by providing a sealed passage for power and signals. This project was undertaken to fill the equipment gap of EPA and Cabling Systems that require much more severe environmental requirements than legacy plant applications present due to their smaller containment volumes that result in high energy densities compared to legacy designs. This high energy density results in severe accident environments and also more severe normal operating conditions.This document describes cost effective approaches to qualify a unique EPA for Small Modular Reactor (SMR) technologies as legacy LWR EPA technologies will likely have inherent material performance insufficiencies. The DBA profiles for SMRs (and some Advanced Reactor Technologies) are more severe than the legacy qualification requirements making the design of the qualification testing system challenging as the temperatures and pressures can approach the limits permitted by ASME Pressure Vessel Code, as well as accident temperatures exceeding the capability of polymeric gaskets and dielectrics. Small Modular Reactors are designed to have, as the name suggests, modularity which implies sized for factory fabrication and subsequent assembly at the power plant site. SMR containment is much smaller than a legacy Light Water Reactor containment. The containment walls are likely to be comprised of stainless steel. Qualifying Electrical Penetration Assemblies (EPAs) through these steel vessels are of interest in this work. Methods are presented here that discuss critical safety and cost effectiveness for these SMR EPA’s test systems.
22 GENERAL STUDIES OF NUCLEAR REACTORS↗
Bolt force to flatten warped flanges.
Bolt load necessary to flatten flange of pipe connector to achieve positive gasket compression for leakage prevention
STRESS AND LOAD↗
Pressure seal ring may be effective over wide temperature range
Positive pressure seal rings seal bolted flange joints in pressure vessels containing fluids whose temperatures can vary over a wide range. The seal rings mate with grooves in the flanges and compensate for the excessive thermal expansion or contraction of a gasketed joint.
Source record↗
Thin plastic sheet eliminates need for expensive plating
Gasket of a commercially available plastic material is interposed between the mating surfaces in axial joints where a hard and a soft metal are in intimate contact under stress conditions. This eliminates the fretting problem and is quicker and less expensive than the plating process.
Stremel, R. L.↗