Search NASA⌕ Search

SEARCH · Search NASA

Results for “GNSS Receiver”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS2023

Level-1 Calibration Assessment of Spire’s LEMUR-2 GNSS-R Ocean Normalized Bistatic Radar Cross Section Estimates

An assessment of the ocean surface Level-1 Normalized Bistatic Radar Cross Section products provided by the two batch 1 ‘LEMUR-2’ GNSS-R receivers of Spire, Inc. is reported. The analysis uses datasets extending from DOY 345, 2020 to DOY 329, 2021. Initial assessments indicate a highly consistent overall inter-channel response with mean NBRCS differences estimated to be at the 1.00% level over a 7-12 m/s ECMWF reference wind speed range. Efforts to validate the observation systems’ aggregate response relative to ≈3 million co-located CYGNSS measurements suggest a highly complementary behavior with an overall NBRCS correlation of 79.03% highlighting the potential utility of ‘LEMUR-2’ measurements for ocean surface wind sensing and related applications. Non-physical NBRCS dependencies on various Level-1 calibration variables, also observed with GNSS-R previous systems, are nonetheless noted and are explored in detail.

Mohammad M. Al-Khaldi↗
NASA NTRS2018

Assessing the Altimetric Measurement from CYGNSS Data

The Cyclone Global Navigation Satellite System (CYGNSS) mission was designed to study hurricane intensification by measuring wind speeds in tropical cyclones. However, the delay-Doppler maps (DDM) that are produced can be used to estimate the sea surface height (SSH) at the specular reflection point on the ocean surface. Proofof-concept studies that DDMs are suitable to solve for SSH have been recently reported (Clarizia et al., 2016; Mashburn et al., 2018), based on data acquired by the demonstration satellite experiment Tech Demo Sat - 1 (TDS-1) carrying a GNSS-R receiver similar to the ones onboard CYGNSS. Although the precision of each 1sec averaged SSH is considerably lower than that of the existing satellite altimeters, by virtue of the dense coverage and frequent revisit time exhibited by the constellation of 8 microsats, the error may be smoothed down considerably by optimal interpolation (Li et al., 2016). Hence the CYGNSS dataset presents a potential opportunity to sample the tropical oceans, and investigate the sensitivity of the SSH measurements to mesoscale eddies. Our objective is to analyze the CYGNSS data and test a suite of retrieval algorithms, including that of Mashburn et al., 2018 to obtain SSH, to understand the error sources and possible corrections when available. Because of the limited antenna gain of the CYGNSS instrument, the power SNR for general wind conditions is expected to be too low to accurately track the reflection point contribution, resulting in altimetry errors of the order of several meters. Other significant error sources are the CYGNSS satellites orbit knowledge, the ionosphere, the troposphere, the mean sea surface and the tides; some of these errors can be reduced by using models. The corrected SSH data will be assimilated into the ROMS high-resolution ocean model to investigate their ability to reproduce mesoscale eddies in the tropical oceans.

Voronovich, Alexander↗
NASA NTRS2020

Feasibility of “Weak GPS” Real-Time Positioning/Timing at Lunar Distance

There are multiple Global Navigation Satellite Systems (GNSS’s), comprising over 100 navigation satellites in the Earth’s medium and high orbits. Most of these satellites have antennas that point Nadir to earth, and transmit navigation signals so vehicles on Earth’s surface and in its vicinity can perform trilateration and estimate its 3-dimenional (3D) positioning. The sidelobes of these antennas can occasionally point to the Moon. It is postulated that a lunar vehicle carrying a large enough receiving antenna can occasionally detects and receives four or more sidelobes of these weak GNSS signals, thus enabling the vehicle to perform 3D positioning using an onboard GNSS receiver. We propagate the orbits of the GNSS satellites from United States’ Global Positioning Satellite (GPS) constellation, the Europe’s Galileo constellation, and the Russia’s GLONASS constellation, a total of 81 satellites. We simulate the visibility of these satellites by a lunar vehicle in a Near Rectilinear Halo Orbit (NRHO), based on the assumption that the lunar vehicle is “in-view” of a GNSS satellite as long as it falls within the 40- degree beam-width of the satellite. We also simulate the 3D positioning performance as a function of satellites’ ephemeris errors and pseudo-range errors. The preliminary results show that the lunar vehicle can “see” 5 – 13 satellites, and achieve a 3D positioning error (one-sigma) of 200 – 300 meters based on reasonable ephemeris and pseudo- range error assumptions. We also consider the case of using relative positioning to mitigate the GNSS satellites’ ephemeris biases. That is, by assuming a reference receiver with accurately known positioning that is close to the lunar vehicle, and computing the relative position of the lunar vehicle relative to the reference.

Cheung, Kar-Ming↗
NASA NTRS2017

Systems and Methods for Determining Inertial Navigation System Faults

An inertial navigation system (INS) includes a primary inertial navigation system (INS) unit configured to receive accelerometer measurements from an accelerometer and angular velocity measurements from a gyroscope. The primary INS unit is further configured to receive global navigation satellite system (GNSS) signals from a GNSS sensor and to determine a first set of kinematic state vectors based on the accelerometer measurements, the angular velocity measurements, and the GNSS signals. The INS further includes a secondary INS unit configured to receive the accelerometer measurements and the angular velocity measurements and to determine a second set of kinematic state vectors of the vehicle based on the accelerometer measurements and the angular velocity measurements. A health management system is configured to compare the first set of kinematic state vectors and the second set of kinematic state vectors to determine faults associated with the accelerometer or the gyroscope based on the comparison.

Bharadwaj, Raj Mohan↗
NASA NTRS2021

Comparison of SAR and CYNSS surface water extent metrics over the Yucatan Lake wetland site

Wetlands have a major role in the carbon cycle, outgassing large quantities of carbon dioxide and methane through processes that are directly and strongly influenced by the duration and timing of inundation. Therefore, understanding the seasonal pattern of inundation can be a component for regional to global scale carbon models. Measurement of inundation extent also establishes a benchmark for the current status of wetland areas, useful in assessing the future impacts of climate change. The incorporation of frequent measurements of inundation extent into large-scale hydrological models would permit the evaluation of more detailed seasonal and longer-term floodplain dynamics and their associated management implications.The Cyclone GNSS (CYGNSS) constellation of satellites launched in 2016, and carries receivers capable of receiving data from L-band GNSS reflections. Delay Doppler maps (DDM) are generated on board and telemetered to the ground, along with a small number of raw data takes that can be used for special processing on the ground for evaluation purposes. It has been previously shown that these data can be sensitive to inundation.The NASA ISRO Synthetic Aperture Radar, currently planned for launch in January 2023, has both an L-band and S-band SAR for earth imaging. The L-band SAR, which will image the Earth's land mass twice every 12 days, has a requirement for measuring wetland inundation extent at the 1 ha scale. One of the sites that will be used to validate this requirement is Yucatan Lake, Louisiana. This oxbow lake and surrounding area located adjacent to the Mississippi river experiences periodic and extensive flooding in the surrounding forest areas.In 2019, NASA's UAVSAR fully polarimetric airborne L-band SAR conducted a flight campaign to image a dozen sites in the SE USA at approximately 12-day intervals and both in the morning and evening, to simulate the type of data NISAR will obtain. One site imaged during this campaign was the Yucatan Lake area, spanning water stages from low to high flood conditions.It has been demonstrated previously that GNSS reflectometry such as that measured by CYGNSS may be used to characterize surface inundation. It has also been known for decades that L-band SAR may be used to characterize not only the presence of open water, but also the presence of subcanopy inundation in forested areas. In this paper we will present results comparing data from these two types of instruments.

Lavalle, Marco↗
NASA NTRS2017

The Sensitivity of Ground-Reflected GNSS Signals to Near-Surface Soil Moisture, as Recorded by Spaceborne Receivers

Spatial and temporal variations in near-surface soil moisture are important to measure for climate studies, numerical weather forecasts, and drought monitoring. Several previous studies have shown success in using ground-reflected Global Navigation Satellite System (GNSS) signals as a form of bistatic radar to sense soil moisture. However, the ability of this type of data to sense soil moisture variations from space is still a nascent field of study. In the past two years, three satellites have been launched that were either designed to capture ground-reflected GNSS signals or have been modified to record these signals. The data provided by these satellites are giving scientists an unprecedented opportunity to investigate their ability to detect changes in Earth’s land surface, including but certainly not limited to near-surface soil moisture. This paper will present spaceborne observations of ground-reflected GNSS signals and evaluate their sensitivity to near-surface soil moisture. This sensitivity will be compared to empirical and theoretical sensitivities of monostatic L-band radar measurements to soil moisture. We will also comment on possibilities for retrieval algorithm development, using techniques employed for monostatic radar as a guide.

Chew, C.↗
DOE OSTI2022

Jitter tracking anti-spoofing algorithm

A system and method to distinguish spoofing signals from true GNSS signals is disclosed. One aspect of the present invention combines measuring GNSS carrier signals with measuring jitter in a vehicle's position via a low-cost inertial measurement unit (IMU) to distinguish spoofing signals from true GNSS signals. The present invention employs natural and/or artificial jitter of a vehicle, that, when combined with a tightly coupled inertial navigation system (INS), allows the receiver to distinguish the spoofing GNSS signal from the true GNSS signal. This spoofer survivability algorithm may be implemented, for example, in the software of a GNSS (or GPS) navigation system.

Brashar, Connor↗
NASA NTRS2023

First Observations With A Gnss Antenna to Radio Telescope Interferometer

We describe the design of a radio interferometer composed of a Global Navigation Satellite Systems (GNSS) antenna and a Very Long Baseline Interferometry radio telescope. Our eventual goal is to use this interferometer for geodetic applications including local tie measurements. The GNSS element of the interferometer uses a unique software-defined receiving system and modified commercial geodetic-quality GNSS antenna. We ran three observing sessions in 2022 between a 25 m radio telescope in Fort Davis, Texas (FD-VLBA), a transportable GNSS antenna placed within 100 m, and a GNSS antenna placed at a distance of about 9 km. We have detected a strong interferometric response with a Signal-to-Noise Ratio (SNR) of over 1,000 from Global Positioning System and Galileo satellites. We also observed natural radio sources including Galactic supernova remnants and Active Galactic Nuclei located as far as one gigaparsec, thus extending the range of sources that can be referenced to a GNSS antenna by 18 orders of magnitude. These detections represent the first observations made with a GNSS antenna to radio telescope interferometer. We have developed a novel technique based on a Precise Point Positioning solution of the recorded GNSS signal that allows us to extend integration time at 1.5 GHz to at least 20 min without any noticeable SNR degradation when a rubidium frequency standard is used.

Geodesy↗
NASA NTRSDate not supplied

Predicting GPS Fidelity in Heavily Forested Areas

There is a compelling need to advance the safety of low altitude flight in forested areas. Signal scattering by trees can interfere with GNSS signal reception and can cause navigation loss within and adjacent to woodlands. An estimate of the signal loss vs. foliage depth is needed to quantify navigational degradation by trees at low altitudes. A previous report described a method which attempts to quantify satellite signal degradation caused by foliage by comparing carrier-to-noise ratio (C/N0) to foliage depth along geometric rays cast from the receiver location to the orbital position of GNSS satellites through a 3D matrix of terrain data. A characteristic curve of attenuation vs. foliage depth was found for both L1 and L2 signals at a single forested site. The current study replicates this result at three additional sites, describes refinements to the method, and explores inherent uncertainties that arise from radiofrequency fading and from receiver limitations for weak signals. For the sites surveyed, 60% and 90% of navigational signal is lost at 10m and 20m of foliage depth, respectively. Since this technique uses low-cost hardware and readily available data collection software, it can allow aviators to estimate GNSS position fidelity in flight ranges near trees.

GPS↗
NASA NTRSDate not supplied

Predicting GPS Fidelity in Heavily Forested Areas

There is a compelling need to advance the safety of low altitude flight in forested areas. Signal scattering by trees can interfere with GNSS signal reception and can cause navigation loss within and adjacent to woodlands. An estimate of the signal loss vs. foliage depth is needed to quantify navigational degradation by trees at low altitudes. A previous report described a method which attempts to quantify satellite signal degradation caused by foliage by comparing carrier-to-noise ratio (C/N0) to foliage depth along geometric rays cast from the receiver location to the orbital position of GNSS satellites through a 3D matrix of terrain data. A characteristic curve of attenuation vs. foliage depth was found for both L1 and L2 signals at a single forested site. The current study replicates this result at three additional sites, describes refinements to the method, and explores inherent uncertainties that arise from radiofrequency fading and from receiver limitations for weak signals. For the sites surveyed, 60% and 90% of navigational signal is lost at 10m and 20m of foliage depth, respectively. Since this technique uses low-cost hardware and readily available data collection software, it can allow aviators to estimate GNSS position fidelity in flight ranges near trees.

GPS↗
NASA NTRSDate not supplied

Multipath Mitigation via Clustering for Position Estimation Refinement in Urban Environments

Position estimation using global navigation satellite systems (GNSS) suffers from poor accuracy within urban canyons due to significant signal disruption caused by tall buildings. This issue can be attributed to the GNSS signals reflecting off buildings resulting in severe multipath reflections which degrade the receiver's performance. In this paper, we introduce an innovative approach to filter GNSS satellite measurements to improve the accuracy of the estimated position by leveraging a clustering algorithm. This approach utilizes a predictive GNSS availability service to filter out non-line-of-sight measurements. Then, a subset of line-of-sight satellite measurement combinations are evaluated using a clustering algorithm. When combined, results show these techniques can reduce the mean horizontal error measured in an urban canyon by nearly an order of magnitude, from ~ 18 meters to ~ 2 meters when using a single point positioning solver.

GPS↗
NASA NTRSDate not supplied

Multipath Mitigation via Clustering for Position Estimation Refinement in Urban Environments

Position estimation using global navigation satellite systems (GNSS) suffers from poor accuracy within urban canyons due to significant signal disruption caused by tall buildings. This issue can be attributed to the GNSS signals reflecting off buildings resulting in severe multipath reflections which degrade the receiver's performance. In this paper, we introduce an innovative approach to filter GNSS satellite measurements to improve the accuracy of the estimated position by leveraging a clustering algorithm. This approach utilizes a predictive GNSS availability service to filter out non-line-of-sight measurements. Then, a subset of line-of-sight satellite measurement combinations are evaluated using a clustering algorithm. When combined, results show these techniques can reduce the mean horizontal error measured in an urban canyon by nearly an order of magnitude, from ~ 18 meters to ~ 2 meters when using a single point positioning solver.

GPS↗
NASA NTRS2016

GPS and Galileo Developments on Board the International Space Station With the Space Communications and Navigation (SCaN) Testbed

The Space Communications and Navigation (SCaN) is a facility developed by NASA and hosted on board the International Space Station (ISS) on an external truss since 2013.It has the objective of testing navigation and communication experimentations with a Software Defined Radio (SDR) approach, which permits software updates for testing new experimentations.NASA has developed the Space Telecommunications Radio System (STRS) architecture standard for SDRs used in space and ground-based platforms to provide commonality among radio developments to provide enhanced capability. The hardware is equipped with both L band front-end radios and the NASA space network communicates with it using S-band, Ku-band and Ka-band links.In May 2016 Qascom started GARISS (GPS and Galileo Receiver for the ISS), an activity of experimentation in collaboration with ESA and NASA that has the objective to develop and validate the acquisition and processing of combined GPS and Galileo signals on board the ISS SCaN testbed. This paper has the objective to present the mission, and provide preliminary details about the challenges in the design, development and verification of the waveform that will be installed on equipment with limited resources. GARISS is also the first attempt to develop a waveform for the ISS as part of an international collaboration between US and Europe. Although the final mission objective is to target dual frequency processing, initial operations will foresee a single frequency processing. Initial results and trade-off between the two options, as well as the final decision will be presented and discussed. The limited resources on board the SCaN with respect to the challenging requirements to acquire and track contemporaneously two satellite navigation systems, with different modulations and data structure, led to the need to assess the possibility of aiding from ground through the S-band. This option would allow assistance to the space receiver in order to provide knowledge of GNSS orbits and reduce the processing on board. Trade off and various options for telemetry and uplink data are presented and discussed. Finally, integration and validation of the waveform are one of the major challenges of GARISS: The Experiment Development System (EDS) and the the Ground Integration Unit (GIU) for VV will be used prior to conducting the experiment on the ISS. The EDS can be used in lab environment and allows prototyping and verification activities with the simulator, but does not include all hardware components. The GIU on the other side is the flight model which replicates the flying equipment, but has limited flexibility for testing.As conclusion, the project is now approaching the Preliminary Design Review (PDR) and indeed only preliminary results are available. This paper is an opportunity to present the GARISS mission as part of an International cooperation between ESA, NASA and Qascom. The preliminary results include GPS and Galileo processing from space signals, the challenges and trade off decisions, the high level STRS architecture and foreseen experimentation campaign. Detailed results from the test campaigns are expected in 2017.

space navigation↗
NASA NTRS2018

Survey of Localized Solar Flare Signatures in the Ionosphere with GNSS, VLF, and GOES Observations

Global navigation satellite system (GNSS) phase measurements of the total electron content (TEC) and ionospheric delay are sensitive to sudden increases in electron density in the layers of the Earth’s ionosphere. These sudden ionospheric disruptions, or SIDs, are due to enhanced X-ray and extreme ultraviolet radiation from a solar flare that drastically increases the electron density in localized regions. SIDs are solar flare signatures in the Earth’s ionosphere and can be observed with very low frequency (VLF ~ 3-30 kHz) monitors and dual-frequency GNSS (L1 = 1575.42 MHz, L2 = 1227.60 MHz) receivers that probe lower (D-region) to upper (F-region) ionospheric layers, respectively.

Blevins, Sandra↗
NASA NTRS2017

Autonomous Navigation Above the GNSS Constellations and Beyond: GPS Navigation for the Magnetospheric Multiscale Mission and SEXTANT Pulsar Navigation Demonstration

This talk will describe two first-of-their-kind technology demonstrations attached to ongoing NASA science missions, both of which aim to extend the range of autonomous spacecraft navigation far from the Earth. First, we will describe the onboard GPS navigation system for the Magnetospheric Multiscale (MMS) mission which is currently operating in elliptic orbits reaching nearly halfway to the Moon. The MMS navigation system is a key outgrowth of a larger effort at NASA Goddard Space Flight Center to advance high-altitude Global Navigation Satellite System (GNSS) navigation on multiple fronts, including developing Global Positioning System receivers and onboard navigation software, running simulation studies, and leading efforts to characterize and protect signals at high-altitude in the so-called GNSS Space-Service Volume (SSV). In the second part of the talk, we will describe the Station Explorer for X-ray Timing and Navigation Technology (SEXTANT) mission that aims to make the first in-space demonstration of X-ray pulsar navigation (XNAV). SEXTANT is attached to the NASA astrophysics mission Neutron-star Interior Composition ExploreR (NICER) whose International Space Station mounted X-ray telescope is investigating the fundamental physics of extremes in gravity, material density, and electromagnetic fields found in neutron stars, and whose instrument provides a nearly ideal navigation sensor for XNAV.

Winternitz, Luke↗
NASA NTRS2020

Improved Orbit Determination of the Cygnss Satellites and its Application to Gnss-R Ocean Altimetry

The accuracy of spaceborne ocean surface altimetry depends on precise knowledge of the altimeter satellite orbit. Previous studies of the potential utility of CYGNSS GNSS Reflectometry (GNSS-R) measurements for ocean altimetry have identified its orbit error as a limiting factor. To address this, a recent firmware upgrade to the CYGNSS satellites have enabled the downlink of additional GPS raw measurements from its navigation receiver and increased numerical precision in open-loop GNSS-R tracking information. In this paper, we present improvements to the accuracy of both the orbit determination and the ocean surface height retrievals as a result of these recent upgrades. JPL’s GipsyX software is used to process 120 days of GPS navigation measurements for one of the 8 CYGNSS satellites. Incorporating high fidelity dynamic models and antenna group delay correction, daily orbit overlaps throughout the period show mean RMS differences of 3 cm in height, 7 cm in cross-track, and 10 cm in along-track. Applying these new orbits reduced the standard deviation of retrieved surface height anomalies. When spatially averaged, the sea surface height anomalies were reduced from 1.0 m to 0.8 m. Further improvements are expected using new ionospheric corrections and re-tracking methods currently in development.

Conrad, Alex↗
NASA NTRS2012

Phased Array GNSS Antenna for the FORMOSAT-7/COSMIC-2 Radio Occultation Mission

Future GNSS remote sensing instruments such as the TriG receiver require more capable antennas than those flown on missions such as COSMIC. To maximize the number of ionospheric and atmospheric profiles, the TriG receiver will be capable of tracking legacy and new GPS signals such as L5, L2C and L1C; GLONASS CDMA and Galileo E1 and E5a. There has been an in-house effort at JPL to develop a set of antennas that would provide excellent Radio Occultations performance as well as navigation and ionospheric profiling. This effort is on-going but near completion for the manufacture and delivery of a set of flight antennas for the FORMOSAT-7/COSMIC-2 mission.

Turbiner, Dmitry↗