SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Results of work done on active controls on the modified YF-17 flutter model are summarized. The basic derivation of a suitable control law is discussed. It is shown that discrepencies found between analysis and wind tunnel tests originate from the lack of proper implementation of the desired control law. Program capabilities are described.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Advances in sensors and avionics computation power suggest real-time structural load measurements could be used in flight control systems for improved safety and performance. A conventional transport flight control system determines the moments necessary to meet the pilot's command, while rejecting disturbances and maintaining stability of the aircraft. Control allocation is the problem of converting these desired moments into control effector commands. In this paper, a framework is proposed to incorporate real-time structural load feedback and structural load constraints in the control allocator. Constrained optimal control allocation can be used to achieve desired moments without exceeding specified limits on monitored load points. Minimization of structural loads by the control allocator is used to alleviate gust loads. The framework to incorporate structural loads in the flight control system and an optimal control allocation algorithm will be described and then demonstrated on a nonlinear simulation of a generic transport aircraft with flight dynamics and static structural loads.
This paper presents the gust load alleviation (GLA) study of the aspect ratio 13.5 Common Research Model (CRM) wind-tunnel model. This study details the design of the GLA controller in preparation for wind-tunnel testing in the Transonic Dynamics Tunnel at NASA Langley Research Center. An aeroservolastic (ASE) model was first reduced using a model reduction method that takes advantage of the sinusoidal steady-state response. Then, the reduced model was used to design an extended-state Kalman filter which estimates the states and the sinusoidal gust input. The GLA control was then derived using the optimal control solution to a multi-objective cost function. The results of the GLA controller indicate a 75.6% reduction in wing-root strain while maintaining robust stability margins. The final paper will include performance under sub-optimal conditions, e.g., sensor noise, uncertainty in gust frequency, etc..
This paper presents the gust load alleviation (GLA) study of the aspect ratio 13.5 Common Research Model (CRM) wind-tunnel model. This study details the design of the GLA controller in preparation for wind-tunnel testing in the Transonic Dynamics Tunnel at NASA Langley Research Center. An aeroservolastic (ASE) model is first reduced using a model reduction method that takes advantage of the sinusoidal steady-state response. Then, the reduced model is used to design an extended-state Kalman filter which estimates the states and the sinusoidal gust input. The GLA control is then derived using the optimal control solution to a multi-objective cost function. The results of the GLA controller indicate a 69.07% reduction in wing-root strain without sensor noise and 68.45% reduction with sensor noise, while maintaining robust stability margins. An adaptive GLA controller is developed for uncertain gust frequency and shows a 71.03% reduction in wing root strain compared to the non-adaptive control reduction of just 39.19%.
Two control schemes designed to alleviate gust-induced vibration are analytically investigated for a helicopter with four articulated blades. One is an individual blade pitch control scheme. The other is an adaptive blade pitch control algorithm based on linear optimal control theory. In both controllers, control inputs to alleviate gust response are superimposed on the conventional control inputs required to maintain the trim condition. A sinusoidal vertical gust model and a step gust model are used. The individual blade pitch control, in this research, is composed of sensors and a pitch control actuator for each blade. Each sensor can detect flapwise (or lead-lag or torsionwise) deflection of the respective blade. The acturator controls the blade pitch angle for gust alleviation. Theoretical calculations to predict the performance of this feedback system have been conducted by means of the harmonic method. The adaptive blade pitch control system is composed of a set of measurements (oscillatory hub forces and moments), an identification system using a Kalman filter, and a control system based on the minimization of the quadratic performance function.
Atmospheric turbulence adversely affects operation of commercial and military aircraft and is a design constraint. The airplane structure must be designed to survive the loads imposed by turbulence. Reducing these loads allows the airplane structure to be lighter, a substantial advantage for a commercial airplane. Gust alleviation systems based on accelerometers mounted in the airplane can reduce the maximum gust loads by a small fraction. These systems still represent an economic advantage. The ability to reduce the gust load increases tremendously if the turbulent gust can be measured before the airplane encounters it. A lidar system can make measurements of turbulent gusts ahead of the airplane, and the NASA Airborne Coherent Lidar for Advanced In-Flight Measurements (ACLAIM) program is developing such a lidar. The ACLAIM program is intended to develop a prototype lidar system for use in feasibility testing of gust load alleviation systems and other airborne lidar applications, to define applications of lidar with the potential for improving airplane performance, and to determine the feasibility and benefits of these applications. This paper gives an overview of the ACLAIM program, describes the lidar architecture for a gust alleviation system, and describes the prototype ACLAIM lidar system.
The application of active controls technology to subsonic, long-range transport aircraft was investigated in three Advanced Transport Technology system studies. Relaxed stability requirements, maneuver and gust load alleviation, and active flutter suppression were the concepts considered. A different configuration was investigated for each of the three airframe manufacturers, and each had a somewhat different approach to the application of active controls technology. Consequently, the results varied in magnitude between the contractors, but several trends were noted. Relaxed stability requirements resulted in the largest benefits - reduced weight, increased return on investment, and decreased direct operating costs. Maneuver load alleviation, gust load alleviation, and flutter suppression resulted in much smaller benefits. Prior to application of active controls technology, a research and development program directed toward fulfilling data base requirements, establishing effective design techniques and criteria, improving systems maintainability and reliability, and demonstrating technology readiness must be completed.
The goal of this work is to conduct aeroservoelastic optimization of a high aspect ratio transport wingbox with distributed control surfaces along the trailing edge. The control surfaces are utilized for both quasi-steady maneuver load alleviation (MLA) and unsteady gust load alleviation (GLA). The optimizer dictates the sizing details of the wingbox, the steady and unsteady control surface rotations, and also the control surface layout. Layout design variables specifically dictate which control surfaces to retain, and which to remove. The objective function is to minimize the sum of the actuator weight and the structural weight, with several imposed constraints related to structural failure and actuator saturation. The optimizer’s preferences with regards to control surface layout for MLA are in strong contrast to GLA-driven designs. The GLA-driven design space also suffers from local minima not evident in the MLA space.
A study is made of the longitudinal response of a STOL airplane equipped with a vanecontrolled gust-alleviation system. Effects of various combinations of design parameters on the responses to horizontal and vertical gusts and to elevator inputs are presented. Almost complete gust alleviation may be obtained with this system when the center of gravity of the STOL airplane is at rearward locations, but pitch stability augmentation is required for satisfactory control characteristics.
A technique for gust load alleviation (GLA) flight testing that will approximate a turbulence-like excitation of the wing has been devised. An artificial excitation is produced by randomly deflecting inboard control surfaces on the wing, thereby producing incremental loads on the wing. This presentation covers the background and development of the flight test technique and analyses performed to date.
An analytical study was conducted to define the basic configuration of an active control system for helicopter vibration and gust response alleviation. The study culminated in a control system design which has two separate systems: narrow band loop for vibration reduction and wider band loop for gust response alleviation. The narrow band vibration loop utilizes the standard swashplate control configuration to input controller for the vibration loop is based on adaptive optimal control theory and is designed to adapt to any flight condition including maneuvers and transients. The prime characteristics of the vibration control system is its real time capability. The gust alleviation control system studied consists of optimal sampled data feedback gains together with an optimal one-step-ahead prediction. The prediction permits the estimation of the gust disturbance which can then be used to minimize the gust effects on the helicopter.
of a two part document. Part 2 is titled: "Aeroservoelastic Testing of Free Flying Wind Tunnel Models, Part 2: A Centerline Supported Fullspan Model Tested for Gust Load Alleviation." A team comprised of the Air Force Research Laboratory (AFRL), Northrop Grumman, Lockheed Martin, and the NASA Langley Research Center conducted three aeroservoelastic wind tunnel tests in the Transonic Dynamics Tunnel to demonstrate active control technologies relevant to large, flexible vehicles. In the first of these three tests, a semispan, aeroelastically scaled, wind tunnel model of a flying wing SensorCraft vehicle was mounted to a force balance to demonstrate gust load alleviation. In the second and third tests, the same wing was mated to a new, multi-degree of freedom, sidewall mount. This mount allowed the half-span model to translate vertically and pitch at the wing root, allowing better simulation of the full span vehicle's rigid body modes. Gust load alleviation (GLA) and Body freedom flutter (BFF) suppression were successfully demonstrated. The rigid body degrees-of-freedom required that the model be flown in the wind tunnel using an active control system. This risky mode of testing necessitated that a model arrestment system be integrated into the new mount. The safe and successful completion of these free flying tests required the development and integration of custom hardware and software. This paper describes the many systems, software, and procedures that were developed as part of this effort.