Search NASASearch

SEARCH · Search NASA

Results for “Graphite matrix”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Primary igneous carbon in ureilites - Petrological implications

The ureilite meteorites are carbonaceous olivine-pyroxene achondrites. They typically contain up to 4 wt.% carbon (carbonaceous matrix) as graphite, diamond, and lonsdaleite. Shock degradation has effectively obliterated primary textures in the carbonaceous matrix of previously described ureilites, a factor that has hampered efforts to explain the origin of this material. In contrast, the Antarctic ureilite ALHA78019 displays perfectly preserved primary textures in the carbonaceous matrix characterized by euhedral graphite blades intergrown with Fe-Ni metal and sulfide (diamonds are absent). This petrographic feature suggests that most graphite in ureilites originated by crystallization from a C-rich metallic phase. Assuming that fO2 is controlled by C-CO-CO2 reactions, the compositions of silicates and metals in ureilites imply a two-stage redox history. The noble gases and rare earths of ureilites are discussed in light of this model.

Berkely, J. L.

Effects of matrix toughness on fatigue response of graphite fiber composite laminates

The effect of the matrix toughness on the fatigue response of graphite-fiber-composite laminates was investigated by comparing the fatigue-response results, obtained using the test method of Bakis et al. (1989), for two graphite-epoxy specimens subjected to constant-amplitude fully-reversed loading, namely, (0/ +45/90/ -45)s4 AS4/PEEK samples with drilled center holes and T300-5208 samples. It was found that, although similar matrix damage modes were observed in the two materials, several significant differences occurred in the S-N data and in stiffness data taken over the lives of the two materials, especially at high cyclic stresses.

Simonds, Robert A.

The correlation of low-velocity impact resistance of graphite-fiber-reinforced composites with matrix properties

Summarized are basic studies that were conducted to correlate the impact resistance of graphite-fiber-reinforced composites with polymer matrix properties. Three crosslinked epoxy resins and a linear polysulfone were selected as composite matrices. As a group, these resins possess a significantly large range of mechanical properties. The mechanical properties of the resins and their respective composites were measured. Neat resin specimens and unidirectional and crossply composite specimens were impact tested with an instrumented dropweight tester. Impact resistances of the specimens were assessed on the basis of loading capability, energy absorption, and extent of damage.

Bowles, K. J.

The correlation of low-velocity impact resistance of graphite-fiber-reinforced composites with matrix properties

Summarized are basic studies that were conducted to correlate the impact resistance of graphite-fiber-reinforced composites with polymer matrix properties. Three crosslinked epoxy resins and a linear polysulfone were selected as composite matrices. As a group, these resins possess a significantly large range of mechanical properties. The mechanical properties of the resins and their respective composites were measured. Neat resin specimens and unidirectional and crossply composite specimens were impact tested with an instrumented dropweight tester. Impact resistances of the specimens were assesseed on the basis of loading capability, energy absorption, and extent of damage.

Bowles, Kenneth J.

Influence of electron radiation and temperature on the cyclic, matrix dominated response of graphite-epoxy

The effects of electron radiation and elevated temperature on the matrix-dominated cyclic response of standard T300/934 and a chemically modified T300/934 graphite-epoxy are characterized. Both materials were subjected to 1.0 x 10 to the 10th rads of 1.0 MeV electron irradiation, under vacuum, to simulate 30 years in geosynchronous orbit. Cyclic tests were performed at room temperature and elevated temperature (121 C) on 4-ply unidirectional laminates to characterize the effects associated with irradiation and elevated temperature. Both materials exhibited energy dissipation in their response at elevated temperature. The irradiated modified material also exhibited energy dissipation at room temperature. The combination of elevated temperature and irradiation resulted in the most severe effects in the form of lower proportional limits, and greater energy dissipation. Dynamic-mechanical analysis demonstrated that the glass transition temperature, T(g), of the standard material was lowered 39 C by irradiation, wereas the T(g) of the modified material was lowered 28 C by irradiation. Thermomechanical analysis showed the occurrence of volatile products generated upon heating of the irradiated materials.

Reed, Susan M.

Fillers for improved graphite fiber retention by polymer matrix composites

The results of a program designed to determine the extent to which elemental boron and boron containing fillers added to the matrix resin of graphite/epoxy composites prevent the release of graphite fibers when the composites are exposed to fire and impact conditions are described. The fillers evaluated were boron, boron carbide and aluminum boride. The conditions evaluated were laboratory simulations of those that could exist in the event of an aircraft crash and burn situation. The baseline (i.e., unfilled) laminates evaluated were prepared from commercially available graphite/epoxy. The baseline and filled laminates' mechanical properties, before and after isothermal and humidity aging, also were compared. It was found that a small amount of graphite fiber was released from the baseline graphite/epoxy laminates during the burn and impact conditions used in this program. However, the extent to which the fibers were released is not considered a severe enough problem to preclude the use of graphite reinforced composites in civil aircraft structure. It also was found that the addition of boron and boron containing fillers to the resin matrix eliminated this fiber release. Mechanical properties of laminates containing the boron and boron containing fillers were lower than those of the baseline laminates. These property degradations for two systems: boron (5 micron) at 2.5 percent filler loading, and boron (5 micron) at 5.0 percent filler loading do not appear severe enough to preclude their use in structural composite applications.

House, E. E.

Light weight polymer matrix composite material

A graphite fiber reinforced polymer matrix is layed up, cured, and thermally aged at about 750 F in the presence of an inert gas. The heat treatment improves the structural integrity and alters the electrical conductivity of the materials. In the preferred embodiment PMR-15 polyimides and Celion-6000 graphite fibers are used.

Bowles, Kenneth J.

Light weight polymer matrix composite material

A graphite fiber reinforced polymer matrix is layed up, cured, and thermally aged at about 750.degree. F. in the presence of an inert gas. The heat treatment improves the structural integrity and alters the electrical conductivity of the materials. In the preferred embodiment PMR-15 polyimides and Celion-6000 graphite fibers are used.

Bowles, Kenneth J.

Tensile properties of an ultrahigh-strength graphite fiber in an epoxy matrix

The fiber performance and reinforcement potential for fiber composites of a special PAN-based graphite fiber were evaluated by testing the fiber's tensile properties in an epoxy matrix. Representative strand samples were taken from 30 spools of single-end, 1500-filament fiber to make over 5000 fiber/epoxy strand specimens using the filament-winding process. Characteristics studied were fiber uniformity, strength and modulus distributions at room and liquid-nitrogen temperatures, stress-strain behavior, the effect of strain rate on fiber strength, and acoustic emission during tensile loading to failure. The fiber was found to have a 3570-MPa failure stress, a 1.7% failure strain, a 206-GPa modulus, and a density of 1.77 Mg/cu m at 23 C. Liquid-nitrogen temperature and various strain rates had no significant effect on fiber tensile properties.

Chiao, T. T.

Method of thermal strain hysteresis reduction in metal matrix composites

A method is disclosed for treating graphite reinforced metal matrix composites so as to eliminate thermal strain hysteresis and impart dimensional stability through a large thermal cycle. The method is applied to the composite post fabrication and is effective on metal matrix materials using graphite fibers manufactured by both the hot roll bonding and diffusion bonding techniques. The method consists of first heat treating the material in a solution anneal oven followed by a water quench and then subjecting the material to a cryogenic treatment in a cryogenic oven. This heat treatment and cryogenic stress reflief is effective in imparting a dimensional stability and reduced thermal strain hysteresis in the material over a -250.degree. F. to +250.degree. F. thermal cycle.

Dries, Gregory A.

Carborane Dopant Strengthens Pitch Char

Addition of small amount of soluble, organic boron compound to matrix precursor of carbon-fiber/carbon-matrix (carbon/carbon) composite increases strength and toughness of composite. Compound catalyzes graphitization of matrix, giving rise to greater degree of graphitization at lower processing temperature. Technique used to advantage in carbon/carbon materials requiring lower temperature processing, such as those with inhibited matrices or materials sensitive to changes in fiber properties.

D Kyle Brown

Experimental measurement of material damping for space structures

A procedure for the measurement of material damping is described. The free decay of free-free beams, when lofted into free fall in vacuum, was recorded. Tests were performed on aluminum, graphite/epoxy, and graphite/magnesium metal matrix materials. Specimens with a fundamental free-free frequency below the elaxation frequency showed a higher level of damping and of stress dependence than predicted. For 0 sub 8 laminates, a material damping ratio of 0.00055 was found for fequencies varying from 45 Hz to 237 Hz. The damping was neither stress nor frequency dependent. For 90 sub 8 laminates, the damping ratio ranged from 0.0055 to 0.0066 as frequency ranged from 42 Hz to 143 Hz. Damping ratios for 90 sub 8 specimens were independent of stress. Experimentally measured damping ratios for metal matrix specimens with unidirectional graphite fibers, magnesium matrix, and either titanium or magnesium foil, ranged from .00039 to .00099, depending upon the matrix material, frequency, and possibly the stress range involved.

Crawley, E. F.

Experiment M0003-10: Advanced composites

The Advanced composites Sub-experiment includes numerous metal matrix composites, primarily graphite fiber reinforced aluminum and magnesium, and several classes of graphite fiber reinforced organic matrix (epoxy, polysulfone, polyimide) composites with and/or without thermal control or protective coatings. The experiment included over 500 flight samples, mounted on the leading and trailing edges of LDEF, and a full complement of the laboratory control samples. Preliminary results are presented reviewing changes in the visual appearance of the samples, atomic oxygen erosion of the organic matrix composites, contamination effects, and the effects of micrometeorite impacts and thermal fatigue on the metal matrix composites.

Steckel, Gary L.

Rheological characterization of addition polyimide matrix resins and prepregs

Although graphite-reinforced polyimide matrix composites offer outstanding specific strength and stiffness, together with high thermal oxidative stability, processing problems connected with their rheological behavior remain to be addressed. The present rheological studies on neat polyimide resin systems encountered outgassing during cure. A staging technique has been developed which can successfully handle polyimide samples, and novel methods were applied to generate rheological curves for graphite-reinforced prepregs. The commercial graphite/polyimide systems studied were PRM 15, LARC 160, and V378A.

Maximovich, M. G.

Replacement of MDA with more oxidatively stable diamines in PMR-polyimides

Studies are performed to investigate the effect of substituting 4,4'-oxydianiline and 1,1-bis(4-aminophenyl)-1-phenyl-2,2,2-trifluoroethane for the 4,4'-methylenedianiline in PMR polyimide matrix resin. Graphite fiber reinforced composites are fabricated from unsized Celion 6000 and PMR-polyimide matrix resins having formulated molecular weights in the range of 1500 to 2400. The composite processing characteristics are investigated and the initial room temperature and 316 C (600 F) composite mechanical properties are determined. Comparative 316 C composite weight losses and 316 C mechanical properties retention after prolonged 316 C air exposure are also determined.

Alston, W. B.

Graphite/copper alloy interfacial energies determined using the sessile drop method

Graphite surfaces are not wet by pure copper. This lack of wetting is responsible for a debonding phenomenon that was found in continuous graphite fiber/copper matrix composites materials subjected to elevated temperatures. By suitably alloying copper, its capability to wet graphite surfaces can be enhanced. In situ measurements of graphite/copper alloy wetting angles were made using the sessile drop method. Interfacial energy values were calculated based upon these measurements.

Devincent, Sandra M.

Differences in interfacial bond strengths of graphite fiber-epoxy resin composites

The effect of epoxy-size and degree of cure on the interfacial bonding of an epoxy-amine-graphite fiber composite system is examined. The role of the fiber-resin interface in determining the overall mechanical properties of composites is poorly understood. A good interfacial adhesive bond is required to achieve maximum stress transfer to the fibers in composites, but at the same time some form of energy absorbing interfacial interaction is needed to achieve high fracture toughening. The incompatibility of these two processes makes it important to understand the nature and basic factors involved at the fiber-resin interface as stress is applied. The mechanical properties including interlaminar shear values for graphite fiber-resin composites are low compared to glass and boron-resin composites. These differences have been attributed to poor fiber-matrix adhesion. Graphite fibers are commonly subjected to post-treatments including application of organic sizing in order to improve their compatibility with the resin matrix and to protect the fiber tow from damage during processing and lay-up. In such processes, sized graphite fiber tow is impregnated with epoxy resin and then layed-up i nto the appropriate configuration. Following an extended ambient temperature cure, the graphite-resin composite structure is cured at elevated temperature using a programmed temperature sequence to cure and then cool the product.

Needles, H. L.

Hybrid composites that retain graphite fibers on burning

A laboratory scale program was conducted to determine fiber release tendencies of graphite reinforced/resinous matrix composites currently used or projected for use in civil aircraft. In the event of an aircraft crash and burn situation, there is concern that graphite fibers will be released from the composites once the resin matrix is thermally decomposed. Hybridizing concepts aimed at preventing fiber release on burning were postulated and their effectiveness evaluated under fire, impact, and air flow during an aircraft crash.

House, E. E.