Search NASA⌕ Search

SEARCH · Search NASA

Results for “HINGED ROTOR BLADE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

70 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Multi-objective/loading optimization for rotating composite flexbeams

With the evolution of advanced composites, the feasibility of designing bearingless rotor systems for high speed, demanding maneuver envelopes, and high aircraft gross weights has become a reality. These systems eliminate the need for hinges and heavily loaded bearings by incorporating a composite flexbeam structure which accommodates flapping, lead-lag, and feathering motions by bending and twisting while reacting full blade centrifugal force. The flight characteristics of a bearingless rotor system are largely dependent on hub design, and the principal element in this type of system is the composite flexbeam. As in any hub design, trade off studies must be performed in order to optimize performance, dynamics (stability), handling qualities, and stresses. However, since the flexbeam structure is the primary component which will determine the balance of these characteristics, its design and fabrication are not straightforward. It was concluded that: pitchcase and snubber damper representations are required in the flexbeam model for proper sizing resulting from dynamic requirements; optimization is necessary for flexbeam design, since it reduces the design iteration time and results in an improved design; and inclusion of multiple flight conditions and their corresponding fatigue allowables is necessary for the optimization procedure.

Hamilton, Brian K.↗
NASA NTRS1987

A study of some approximations in the modeling of a coupled rotor/fuselage aeromechanical system

Equations of motion for a three-bladed hingeless rotor coupled to a gimbal-supported fuselage are developed. A brief derivation of the equations is presented, including the assumptions made, the ordering scheme, and a discussion of both the source of the aerodynamic axial load term and the reason for differences due to hinge sequence. The solution of the equations is discussed, including linearization, the use of multiblade coordinates to eliminate periodic coefficients, and specialization to a root-sprung model. The treatment of the blade root offset by using an ordering scheme to neglect higher-order terms is found to affect results in pitch and roll. A small aerodynamic loading term in the blade axial direction has a significant effect at large collective pitch settings, as does the choice of a flap-lag or a lag-flap transformation sequence for blade motion. The results for a hingeless rotor also differ significantly from those for the root-sprung model when the nonrotating natural frequencies are matched.

Blelloch, P. A.↗
NASA NTRS1980

Effects of primary rotor parameters on flapping dynamics

The effects of flapping dynamics of four main rotor design features that influence the agility, stability, and operational safety of helicopters are studied. The parameters include flapping hinge offset, flapping hinge restraint, pitch-flap coupling, and blade lock number. First, the flapping equations of motion are derived that explicitly contain the design parameters. The dynamic equations are then developed for the tip-path plane, and the influence of individual and combined variations in the design parameters determined. The steady state flapping response is examined with respect to control input and aircraft angular rate which leads to a feedforward control law for control decoupling through cross feed, and a feedback control law to decouple the steady state flapping response. The condition for achieving perfect decoupling of the flapping response due to aircraft pitch and roll rates without using feedback control is also found for the hover case. It is indicated that the frequency of the regressing flapping mode of the rotor system can become low enough to require consideration in the assessment of handling characteristics.

Chen, R. T. N.↗
NASA NTRS1985

Reflection plane tests of a wind turbine blade tip section with ailerons

Tests were conducted in the NASA Langley 30 by 60 foot Wind Tunnel on a full scale 7.31 m (24 ft) long tip section of a wind turbine rotor blade. The blade tip section was built with ailerons on the trailing edge. The ailerons, which spanned a length of 6.1 m (20 ft), were designed so that two types could be evaluated: the plain and the balanced. The ailerons were hinged on the suction surface at the 0.62 X chord station behind the leading edge. The purpose of the tests was to measure the aerodynamic characteristics of the blade section for: an angle of attack range from 0 deg to 90 deg aileron deflections from 0 deg to -90 deg, and Reynolds numbers of 0.79 and 1.5 x 10 to the 6th power. These data were then used to determine which aileron configuration had the most desirable rotor control and aerodynamic braking characteristics. Tests were also run to determine the effects of vortex generators, leading edge roughness, and the gaps between the aileron sections on the lift, drag, and chordwise force coefficients of the blade tip section.

Savino, J. M.↗
NASA NTRS1992

Vibration reduction in helicopter rotors using an active control surface located on the blade

A feasibility study of vibration reduction in a four-bladed helicopter rotor using individual blade control (IBC), which is implemented by an individually controlled aerodynamic surface located on each blade, is presented. For this exploratory study, a simple offset-hinged spring restrained model of the blade is used with fully coupled flap-lag-torsional dynamics for each blade. Deterministic controllers based on local and global system models are implemented to reduce 4/rev hub loads using both an actively controlled aerodynamic surface on each blade as well as conventional IBC, where the complete blade undergoes cyclic pitch change. The effectiveness of the two approaches for simultaneous reduction of the 4/rev hub shears and hub moments is compared. Conventional IBC requires considerably more power to achieve approximately the same level of vibration reduction as that obtained by implementing IBC using an active control surface located on the outboard segment of the blade. The effect of blade torsional flexibility on the vibration reduction effectiveness of the actively controlled surface was also considered and it was found that this parameter has a very substantial influence.

Millott, T. A.↗
NASA NTRS1982

Response Characteristics of a Linear Rotorcraft Vibration Model

A fully coupled vibration model, consisting of a rotor with only flapping degrees of freedom plus pylon and fuselage pitching motion, was used in a parametric study undertaken to investigate the response characteristics of a simplified helicopter. Among the parameters studied were uncoupled body frequency, blade stiffness, hinge offset, advance ratio, and mast height. Results from the harmonic balance solution of the equations of motion show how each of these quantities affects the response of the model. The results also indicate that there is a potential for reducing vibration response through the judicious definition of the design parameters.

Kunz, Donald L.↗
NASA NTRS1990

Precise Hinge Has Low Friction

Precise hinge rotates with minimal friction and without "slop". Axis of rotation at central axis of concentric, self-retaining assembly. Blades in same plane, and both edges of blades and apexes of grooves lie along same line, allowing free rotation without either binding or slop. Blades on rotor engage grooves on stator. Blades pivot about edges through arc defined by slotted openings in stator housing.

Collins, Earl R., Jr.↗
NASA NTRS1990

The effects of structural flap-lag and pitch-lag coupling on soft inplane hingeless rotor stability in hover

A 1.62-m-diameter rotor model was tested in hover to examine the effects of structural flap-lag and pitch-lag coupling on isolated rotor blade lead-lag stability. Flap-lag coupling was introduced by inclining the principal axes of the blade structure up to 60 degrees. Pitch-lag coupling was obtained either alone or in combination with flap-lag coupling through the use of skewed flexural hinges. The principal results confirm the predictions of theory, and show that both structural flap-lag and pitch-lag coupling when used separately are beneficial to blade stability. Moreover, when the couplings are combined, the lead-lag damping is significantly greater than it would be if the individual contributions were superimposed. Pitch-flap coupling is shown to have only a minor effect on blade lead-lag damping. Differences between theory and experiment observed at zero blade pitch and flexure angles during the initial testing were determined in a second test to be caused by stand flexibility. Other differences between theory and experiment warrant further investigation.

Bousman, William G.↗
NASA NTRS2002

Maneuvering Rotorcraft Noise Prediction: A New Code for a New Problem

This paper presents the unique aspects of the development of an entirely new maneuver noise prediction code called PSU-WOPWOP. The main focus of the code is the aeroacoustic aspects of the maneuver noise problem, when the aeromechanical input data are provided (namely aircraft and blade motion, blade airloads). The PSU-WOPWOP noise prediction capability was developed for rotors in steady and transient maneuvering flight. Featuring an object-oriented design, the code allows great flexibility for complex rotor configuration and motion (including multiple rotors and full aircraft motion). The relative locations and number of hinges, flexures, and body motions can be arbitrarily specified to match the any specific rotorcraft. An analysis of algorithm efficiency is performed for maneuver noise prediction along with a description of the tradeoffs made specifically for the maneuvering noise problem. Noise predictions for the main rotor of a rotorcraft in steady descent, transient (arrested) descent, hover and a mild "pop-up" maneuver are demonstrated.

Brentner, Kenneth S.↗
NASA NTRS1974

Application to rotary wings of a simplified aerodynamic lifting surface theory for unsteady compressible flow

A general method of predicting airloads is applied to helicopter rotor blades on a full three-dimensional basis using the general theory developed for a rotor blade at the psi = pi/2 position where flutter is most likely to occur. Calculations of aerodynamic coefficients for use in flutter analysis are made for forward and hovering flight with low inflow. The results are compared with values given by two-dimensional strip theory for a rigid rotor hinged at its root. The comparisons indicate the inadequacies of strip theory for airload prediction. One important conclusion drawn from this study is that the curved wake has a substantial effect on the chordwise load distribution.

Rao, B. M.↗
NASA NTRS1994

Low-Noise Rotorcraft Blades

Blades of helicopter rotors, tilt rotors, and like reshaped to reduce noise, according to proposal. Planform features combination of rearward and forward sweep. Forward sweep over large outer portion of blade constitutes primary noise-reduction feature. Relieves some of compressive effect in tip region, with consequent reduction of noise from compressive sources. Performance at high advance ratio improved. Cabin vibration and loading noise reduced by load-averaging effect of double-sweep planform. Aft-swept section provides balancing of aerodynamic and other dynamic forces on blade along 1/4-chord line of straight inboard section and along projection of line to outermost blade radius. Possible for hub-hinge forces and moments to remain within practical bounds. Provides stabilizing blade forces and moments to counteract any instability caused by forward sweep.

Brooks, Thomas F.↗
NASA NTRS1994

Vibration reduction in helicopter rotors using an actively controlled partial span trailing edge flap located on the blade

This report describes an analytical study of vibration reduction in a four-bladed helicopter rotor using an actively controlled, partial span, trailing edge flap located on the blade. The vibration reduction produced by the actively controlled flap (ACF) is compared with that obtained using individual blade control (IBC), in which the entire blade is oscillated in pitch. For both cases a deterministic feedback controller is implemented to reduce the 4/rev hub loads. For all cases considered, the ACF produced vibration reduction comparable with that obtained using IBC, but consumed only 10-30% of the power required to implement IBC. A careful parametric study is conducted to determine the influence of blade torsional stiffness, spanwise location of the control flap, and hinge moment correction on the vibration reduction characteristics of the ACF. The results clearly demonstrate the feasibility of this new approach to vibration reduction. It should be emphasized than the ACF, used together with a conventional swashplate, is completely decoupled from the primary flight control system and thus it has no influence on the airworthiness of the helicopter. This attribute is potentially a significant advantage when compared to IBC.

Millott, T. A.↗
NASA NTRS1982

Helicopter vibration suppression using simple pendulum absorbers on the rotor blade

A comprehensive anaytical design procedure for the installation of simple pendulums on the blades of a helicopter rotor to suppress the root reactions is presented. A frequency response anaysis is conducted of typical rotor blades excited by a harmonic variation of spanwise airload distributions as well as a concentrated load at the tip. The results presented included the effect of pendulum tuning on the minimization of the hub reactions. It is found that a properly designed flapping pendulum attenuates the root out-of-plane force and moment whereas the optimum designed lead-lag pendulum attenuates the root in-plane reactions. For optimum pendulum tuning the parameters to be determined are the pendulum uncoupled natural frequency, the pendulum spanwise location and its mass. It is found that the optimum pendulum frequency is in the vicinity of the excitation frequency. For the optimum pendulum a parametric study is conducted. The parameters varied include prepitch, pretwist, precone and pendulum hinge offset.

Pierce, G. A.↗
NASA NTRSDate not supplied

Prediction of Quadrotor Acoustics Using RVLT Toolchain

The NASA Revolutionary Vertical Lift Technology (RVLT) Project toolchain is used to predict the acoustics of the NASA 6-passenger quadrotor concept vehicle. A qualitative study of the blade vertical loading to understand noise trends with tip speed and number of blades was performed. Trends of the individual rotor noise sources (thickness, loading, and broadband) are studied. Noise is predicted and analyzed for three flight conditions: approach (6-deg descent), level flight flyover, and takeoff. Three quadrotor designs are considered: tip speed=700 ft/sec, 3 blades (“700/3”), “550/3”, and “375/7”. The qualitative study shows that during approach multiple, strong BVIs occur on the advancing and retreating sides for “700/3” and “550/3”, but for “375/7” only weak BVIs are present. Consistent with this BVI scenario, the quadrotor noise results show that “700/3” has the highest loading noise (and EPNL) and “375/7” the lowest loading noise (and EPNL), with “550/3” falling in between. Broadband noise during approach and flyover is roughly the same for all three designs. Takeoff broadband noise is much lower, especially for “375/7”. The bulk of the results have been obtained with a rigid uniform blade model, with a flap hinge and a pitch bearing. For “550/3”, noise predictions with elastic nonuniform blades have been initiated and are ongoing.

Quadrotor↗
NASA NTRS2010

Low Speed and High Speed Correlation of SMART Active Flap Rotor Loads

Measured, open loop and closed loop data from the SMART rotor test in the NASA Ames 40- by 80- Foot Wind Tunnel are compared with CAMRAD II calculations. One open loop high-speed case and four closed loop cases are considered. The closed loop cases include three high-speed cases and one low-speed case. Two of these high-speed cases include a 2 deg flap deflection at 5P case and a test maximum-airspeed case. This study follows a recent, open loop correlation effort that used a simple correction factor for the airfoil pitching moment Mach number. Compared to the earlier effort, the current open loop study considers more fundamental corrections based on advancing blade aerodynamic conditions. The airfoil tables themselves have been studied. Selected modifications to the HH-06 section flap airfoil pitching moment table are implemented. For the closed loop condition, the effect of the flap actuator is modeled by increased flap hinge stiffness. Overall, the open loop correlation is reasonable, thus confirming the basic correctness of the current semi-empirical modifications; the closed loop correlation is also reasonable considering that the current flap model is a first generation model. Detailed correlation results are given in the paper.

Kottapalli, Sesi B. R.↗
NASA NTRS2011

Enhanced Correlation of SMART Active Flap Rotor Loads

This is a follow-on study to a 2010 correlation effort. Measured data from the SMART rotor test in the NASA Ames 40- by 80- Foot Wind Tunnel are compared with CAMRAD II calculations. As background, during the wind tunnel test, unexpectedly high inboard loads were encountered, and it was hypothesized at that time that due to changes in the flexbeams over the years, the flexbeam properties used in the analysis needed updating. Boeing Mesa, recently updated these properties. This correlation study uses the updated flexbeam properties. Compared to earlier studies, the following two enhancements are implemented: i) the inboard loads (pitchcase and flexbeam loads) correlation is included for the first time (reliable prediction of the inboard loads is a prerequisite for any future anticipated flight-testing); ii) the number of blade modes is increased to better capture the flap dynamics and the pitchcase-flexbeam dynamics. Also, aerodynamically, both the rolled-up wake model and the more complex, multiple trailer wake model are used, with the latter slightly improving the blade chordwise moment correlation. This sensitivity to the wake model indicates that CFD is needed. Three high-speed experimental cases, one uncontrolled free flap case and two commanded flap cases, are considered. The two commanded flap cases include a 2o flap deflection at 5P case and a 0o flap deflection case. For the free flap case, selected modifications to the HH-06 section flap airfoil pitching moment table are implemented. For the commanded 2o flap case, the experimental flap variation is approximately matched by increasing the analytical flap hinge stiffness. This increased flap hinge stiffness is retained for the commanded 0o flap case also, which is treated as a free flap case, but with larger flap hinge stiffness. The change in the mid-span and outboard loads correlation due to the updating of the flexbeam properties is not significant. Increasing the number of blade modes results in an effective, commanded flap hinge stiffness of 4X baseline, not 3X as reported earlier. The inboard loads correlation is reasonable, but needs further study. Overall, the free flap case correlation is reasonable, thus confirming the basic correctness of the current semi-empirical modifications; the correlation for the commanded 2o flap at 5P case and the 0o flap case is also reasonable.

Kottapalli, Sesi↗