Surface ionization hysteresis phenomena
Temperature field influence on hysteresis in Cs surface ionization on metal surfaces, observing adsorption phase fine structure and ion current density increase
Wilson, R. G.↗
SEARCH · Search NASA
Results for “HYSTERESIS”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Effect of contact angle hysteresis on moving liquid film integrity
A study was made of the formation and breakdown of a water film moving over solid surfaces (teflon, lucite, stainless steel, and copper). The flow rate associated with film formation was found to be higher than the flow rate at which film breakdown occurred. The difference in the flow rates for film formation and film breakdown was attributed to contact angle hysteresis. Analysis and experiment, which are in good agreement, indicated that film formation and film breakdown are functions of the advancing and receding angles, respectively.
Simon, F. F.↗
Stability of certain periodic solutions of a forced system with hysteresis
Many physical systems exhibit the phenomenon of nonlinear hysteresis when the amplitude of oscillation exceeds some small limit. It was shown that under certain conditions there are periodic motions of such a system with small forcing which are near the largest periodic motion of the corresponding unforced system. Conditions for the stability of these periodic motions are derived.
Drew, J. H.↗
Periodic solutions of a forced system with hysteresis.
Hysteresis damping arising in an oscillatory system due to the phenomenon of slip damping analyzed by Goodman and Klumpp (1956) is considered. An idealized physical model is proposed, and the existence of certain periodic motions is investigated in a system with small forcing which are near the largest periodic motion in a corresponding unforced system. Periodic solutions of the forced system are obtained.-
Drew, J. H.↗
Effect of contact angle hysteresis on moving liquid film integrity.
A study was made of the formation and breakdown of a water film moving over solid surfaces (teflon, lucite, stainless steel, and copper). The flow rate associated with film formation was found to be higher than the flow rate at which film breakdown occurred. The difference in the flow rates for film formation and film breakdown was attributed to contact angle hysteresis. Analysis and experiment, which are in good agreement, indicated that film formation and film breakdown are functions of the advancing and receding angles, respectively.
Simon, F. F.↗
Calculation of the magnetic field in the active zone of a hysteresis clutch
The initial distribution of magnetic induction in the armature stationary was calculated relative to the polar system of a hysteresis clutch. Using several assumptions, the problem is reduced to calculating the static magnetic field in the ferromagnetic plate with finite and continuous magnetic permeability placed in the air gap between two identical, parallel semiconductors with rack fixed relative to the tooth or slot position.
Ermilov, M. A.↗
On the hysteresis of the sea surface and its applicability to wave height predictions
Because of the low dissipation rate of wave energy on the ocean's surface, the wave height at some location and time must be dependent upon wind fields in existence there at previous times and upon swell propagated there from other regions. To study these relationships, significant wave height (SWH) measurements from the Geos-3 radar altimeter are used in conjunction with anemometer windspeed measurements from weather ships, L, C, and R. During the passage of large cyclonic disturbances near the fixed locations of these vessels in the North Atlantic in February 1976, distinct hysteresis profiles that characterize the sea's memory during generation and dissipation conditions are observed. Examples are given that demonstrate the influences of cyclone intensity, movement, velocity, and shape on the configuration of these profiles.
Parsons, C. L.↗
Gas flow across a wet screen - Analogy to a relief valve with hysteresis
The flow of gas through a wet fine-mesh screen is analyzed in terms of the capillary forces of the liquid wetting the screen and the pressure difference across the screen thickness driving the gas flow. Several different types of time-dependent flow are shown to be possible. The most interesting type is one in which the pressure difference opens small channels in the liquid, which are then closed rapidly by the wetting action of the liquid. The opening and closing exhibit hysteresis, and the flow is highly oscillatory.
Nachman, A.↗
Internal hysteresis experienced on a high pressure syn gas compressor
A vibration instability phenomenon experienced in operating high pressure syn gas centrifugal compressors in two ammonia plants is described. The compressors were monitored by orbit and spectrum analysis for changes from baseline readings. It is found that internal hysteresis was the major destabilizing force; however, the problem was further complicated by seal lockup at the suction end of the compressor. A coupling lockup problem and a coupling fit problem, which frettage of the shaft, are also considered as contributors to the self excited vibrations.
Zeidan, F. Y.↗
Vortex flow hysteresis
An experimental study was conducted to quantify the hysteresis associated with various vortex flow transition points and to determine the effect of planform geometry. The transition points observed consisted of the appearance (or disappearance) of trailing edge vortex burst and the transition to (or from) flat plate or totally separated flows. Flow visualization with smoke injected into the vortices was used to identify the transitions on a series of semi-span models tested in a low speed tunnel. The planforms tested included simple deltas (55 deg to 80 deg sweep), cranked wings with varying tip panel sweep and dihedral, and a straked wing. High speed movies at 1000 frames per second were made of the vortex flow visualization in order to better understand the dynamics of vortex flow, burst and transition.
Cunningham, A. M., Jr.↗
Stability of dithered non-linear systems with backlash or hysteresis
A study is conducted of the effect of dither on the nonlinear element of a single-input single-outout feedback system. Nonlinearities are considered with memory (backlash, hysteresis), in the feedforward loop; a dither of a given amplitude is injected at the input of the nonlinearity. The nonlinearity is followed by a linear element with low-pass characteristic. The stability of the dithered system and an approximate equivalent system (in which the nonlinearity is a smooth function) are compared. Conditions on the input and on the dither frequency are obtained so that the approximate-system stability guarantees that of the given hysteretic system.
Desoer, C. A.↗
Low-Hysteresis Flow-Through Wind-Tunnel Balance
Improved flow-through wind-tunnel balance includes features minimizing both spurious force readings caused by internal pressurized flow and mechanical hysteresis. Symmetrical forces caused by internal flow cancelled.
Kunz, N.↗
A Hysteresis Model for Piezoceramic Materials
This paper addresses the modeling of nonlinear constitutive relations and hysteresis inherent to piezoceramic materials at moderate to high drive levels. Such models are, necessary to realize the, full potential of the materials in high performance control applications, and a necessary prerequisite is the development of techniques which permit control implementation. The approach employed here is based on the qualification of reversible and irreversible domain wall motion in response to applied electric fields. A comparison with experimental data illustrates that because the resulting ODE model is physics-based, it can be employed for both characterization and prediction of polarization levels throughout the range of actuator operation. Finally, the ODE formulation is amenable to inversion which facilitates the development of an inverse compensator for linear control design.
Smith, Ralph C.↗
Design of Mechanisms for Deployable, Optical Instruments: Guidelines for Reducing Hysteresis
This paper is intended to facilitate the development of deployable, optical instruments by providing a rational approach for the design, testing, and qualification of high-precision (i.e., low-hysteresis) deployment mechanisms for these instruments. Many of the guidelines included herein come directly from the field of optomechanical engineering, and are, therefore, neither newly developed guidelines, nor are they uniquely applicable to the design of high-precision deployment mechanisms. This paper is to be regarded as a guide to design and not a set of NASA requirements, except as may be defined in formal project specifications. Furthermore, due to the rapid pace of advancement in the field of precision deployment, this paper should be regarded as a preliminary set of guidelines. However, it is expected that this paper, with revisions as experience may indicate to be desirable, might eventually form the basis for a set of uniform design requirements for high-precision deployment mechanisms on future NASA space-based science instruments.
Lake, Mark S.↗
Thin-Film Ferro Electric-Coupled Microstripline Phase Shifters With Reduced Device Hysteresis
This work deals with the performance of coupled microstripline phase shifters (CMPS) fabricated using BaxSr 1 -xTiO 3 (BST) ferroelectric thin films. The CMPS were fabricated using commercially available pulsed laser deposition BST films with Ba:Sr ratios of 30:70 and 20:80. Microwave characterization of these CMPS was performed at upper Kuband frequencies, particularly at frequencies near 16 and 18 GHz. X-ray diffraction studies indicate that the 30:70 films exhibit almost a 1:1 ratio between the in-plane and out-of-plane lattice parameters, suggesting that their cubics create strain -free films suitable for producing CMPS devices with reduced hysteresis in the paraelectric state. The quality of performance of the CMPS was studied based on their relative phase shift and insertion loss within the DC bias range of 0 to 400 V (i.e., E-field ranges within 0 to 53 V/micron). The performance of the CMPS was tested as a function of temperature to investigate their operation in the paraelectric, as well as in the ferroelectric, state (i.e., above and below the Curie temperature, respectively). The novel behavior discussed here is based on the experimental observation of the CMPS. This behavior, observed for the aforementioned cation ratio, highlights the relevance of good crystalline structure for high-quality CMPS.
Miranda, Felix A.↗
Cavitation hysteresis.
Cavitation delay time variation with velocity, size, dissolved air content, liquid tension, flow history and surface characteristics
TIME DELAY↗
Cavitation hysteresis.
Cavitation delay time variation with velocity, size, dissolved air content, liquid tension, flow history and surface characteristics
TIME DELAY↗
Analytic solutions of limit cycles in a feedback-regulated converter system with hysteresis.
Mathematical model for voltage step-down DC to DC converter with hysteretic bistable trigger circuit regulating output voltage
Babaa, I. M. H.↗