SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Low dose reactor irradiation effect on temperature dependence of dynamic modulus and internal friction of as-deposited pyrolytic graphite
A device developed for the direct measurement of wall shear stress generated by flows is described. Simple and symmetric in design with optional small moving mass and no internal friction, the features employed in the design eliminate most of the difficulties associated with the traditional floating element balances. The device is basically small and can be made in various sizes. Vibration problems associated with the floating element skin friction balances were found to be minimized due to the design symmetry and optional damping provided. The design eliminates or reduces the errors associated with conventional floating element devices: such as errors due to gaps, pressure gradient, acceleration, heat transfer, and temperature change. The instrument is equipped with various sensing systems and the output signal is a linear function of the wall shear stress. Dynamic measurements could be made in a limited range and measurements in liquids could be performed readily. Measurement made in the three different tunnels show excellent agreement with data obtained by the floating element devices and other techniques.
The bulk behavior of dispersed, fluidized, or undispersed stationary granular systems cannot be fully understood in terms of adhesive/cohesive properties without understanding the role of electrostatic forces acting at the level of the grains themselves. When grains adhere to a surface, or come in contact with one another in a stationary bulk mass, it is difficult to measure the forces acting on the grains, and the forces themselves that induced the cohesion and adhesion are changed. Even if a single gain were to be scrutinized in the laboratory, it might be difficult, perhaps impossible, to define the distribution and character of surface charging and the three- dimensional relationship that charges (electrons, holes) have to one another. The hypothesis that we propose to test in microgravity (for dielectric materials) is that adhesion and cohesion of granular matter are mediated primarily by dipole forces that do not require the presence of a net charge; in fact, nominally electrically neutral materials should express adhesive and cohesive behavior when the neutrality results from a balance of positive and negative charge carriers. Moreover, the use of net charge alone as a measure of the electrical nature of grain-to-grain relationships within a granular mass may be misleading. We believe that the dipole forces arise from the presence of randomly-distributed positive and negative fixed charge carriers on grains that give rise to a resultant dipole moment. These dipole forces have long-range attraction. Random charges are created whenever there is triboelectrical activity of a granular mass, that is, whenever the grains experience contact/separation sequences or friction. Electrostatic forces are generally under-estimated for their role in causing agglomeration of dispersed grains in particulate clouds, or their role in affecting the internal frictional relationships in packed granular masses. We believe that electrostatic, in particular dipole-mediated processes, are pervasive and probably affect, at some level, everything from astrophysical-scale granular systems such as interstellar nebulae, protoplanetary dust and debris disks, planetary-scale systems such as debris palls from meteorite impact, volcanic eruptions, and aeolian dust storms, all the way to industrial-scale systems in mining, powder and grain processing, pharmaceuticals, and smoke-stack technologies. NASA must concern itself with the electrostatic behavior of dust and sand on Mars because of its potentially critical importance to human exploration. The motion and adhesion of martian surface materials will affect the design and performance of spacesuits, habitats, processing plants, solar panels, and any externally exposed equipment such as surface rovers or communication and weather stations. Additionally, the adhesion of dust and sand could greatly enhance contact with the potentially toxic components of the martian soil.
A new skin friction balance with moving belt has been developed for measurement of the surface shear stress component in the direction of belt motion. The device is described in this paper with typical measurement results. This instrument is symmetric in design with small moving mass negligible internal friction. It is 3.8 cm high, 3.8 cm long and 2.1 cm wide, with the sensing surface 0.7 cm wide and 1.5 cm long, and it can be made in various sizes. The unique design of this instrument has reduced some of the errors associated with conventional floating-element balances. The instrument can use various sensing systems and the output signal is a linear function of the wall shear stress. Measurements show good agreement with data obtained by the floating element balances and flat plate prediction techniques. Dynamic measurements have been made in a limited range. The overall uncertainty of measurement is estimated to be +/- 2 percent.
Equations describing the friction forces generated during landing operations on ships at sea were formulated. These forces depend on the platform reaction and the coefficient of friction. The platform reaction depends on the relative sink rate and the shock absorbing capability of the landing gear. The friction coefficient varies with the surface condition of the landing platform and the angle of yaw of the aircraft relative to the landing platform. Landings by VTOL aircraft, equipped with conventional oleopneumatic landing gears are discussed. Simplifications are introduced to reduce the complexity of the mathematical description of the tire and shock strut characteristics. Approximating the actual complicated force deflection characteristic of the tire by linear relationship is adequate. The internal friction forces in the shock strut are included in the landing gear model. A set of relatively simple equations was obtained by including only those tire and shock strut characteristics that contribute significantly to the generation of landing gear forces.
Comparisons are made among solutions to zonal-mean equations obtained with parameterized friction and radiative cooling and those forced from specified heat and momentum sources. Budget equations are defined for zonally averaged steady state responses in a thin spherically rotating atmosphere. The heat sources and sinks and mean meridional circulation that maintain observed annual and zonal mean temperatures are identified with a diagnostic calculation. Estimates are made of the surface sensible heating, atmospheric latent heating and vertical flux eddy divergences. The heat and moisture sources and sinks are varied to obtain the steady state responses. The Hadley circulation is fairly insensitive to changes in the strength of the eddy momentum flux when sufficient internal friction is present. Varying the width of the total precipitation of the intertropical convergence zone with fixed eddy fluxes and extratropical heat sources yields conditions similar to El Nino. Finally, a minimum speed is found for the jet stream after varying the horizontal eddy momentum fixing latent and eddy heat sources.
Internal friction and dynamic modulus of gold, copper, silver and platinum
Internal friction and dynamic modulus of gold, copper, silver and platinum
Crystal dislocation, internal friction, and dynamic modulus of face centered cubic metals after deformation
Measurements of electrical conductivity, ultrasonic surface wave attenuation, and internal friction loss were made on aluminum alloys 7079-T6, 2219-T31, and 2219-T81 as a function of the onset of stress corrosion.
Pulse method for rapid determination of internal friction and dynamic modulus of materials
Stress graphitizing and boron codeposition effect on dynamic mechanical properties of pyrolytic carbon, noting increase in internal friction and dynamic modulus
Internal friction, Young modulus and resistivity measurements for stage I interstitials in electron irradiated tungsten
Love wave amplitude data satisfying earth model with intrinsic internal friction at depths assumed due to single thermally activated relaxation
Shear load, cohesion and internal friction measurements of low bulk density particulate silicates of complex shape, noting significance for lunar comparison
Dopant effect on dislocation mobility in elastically loaded silicon crystal using internal friction and modulus defect measurements
Seismic wave attenuation mechanisms emphasizing partial melting, grain boundary relaxation and high temperature internal friction background
Studying Lunar Orbiter photographs of boulder tracks left on lunar surface to determine soil cohesion and angle of internal friction