Search NASA⌕ Search

SEARCH · Search NASA

Results for “In-operando”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Revealing the growth kinetics of atmospheric corrosion pitting in aluminum via in situ microtomography

Abstract Understanding the mechanistic relationship between the environment, microstructure, and local kinetics of atmospheric corrosion damage remains a central challenge. To address this challenge, this study used laboratory-based X-ray tomography to directly observe attack in-operando over an extended period, enabling insights into the evolving growth kinetics and morphology of individual pits over months of exposure. Damage progression associated with nine pits in a 99.9% pure aluminum wire exposed to chloride salts in humid air was characterized. Most pits grew at a nominally linear rate up until pit death, which occurred within 12–24 h of nucleation. Exceptions to this were observed, with three pits exhibiting bimodal growth kinetics and growing for 40 or more hours. This was explained by secondary droplets that formed near the pits, increasing the cathode area. A corrosion-driven drying mechanism likely contributed to pit death in both cases. Pits first grew into the material followed by lateral expansion.

36 MATERIALS SCIENCE↗

Towards developing robust solid lubricant operable in multifarious environments

Abstract Conventional solid lubricants such as MoS 2 , graphite, or diamond-like carbon films demonstrate excellent tribological performance but only in specific environments due to their inherent materials properties. This limitation prohibits using these solid lubricants in environments that change dynamically. This study presents the results of a novel solid lubricant that was developed using a combination of solution-processed 2D-molybdenum disulfide and graphene-oxide (GO) that can be deposited on to stainless steel substrates using a simple spray-coating technique and show exceptional performance in multifarious environments namely, ambient (humid) atmosphere, dry nitrogen, and vacuum. The tribological performance of the coatings was evaluated using a ball-on-disc sliding test and demonstrated an excellent wear/friction performance in all environments and coating survived even after 44 km of linear sliding. Transmission electron microscopy and Raman spectroscopy analysis of the tribolayers suggested in-operando friction-induced re-orientation of MoS 2 layers that were protected by GO layers and, an absence of MoO x peaks indicate a strong resistance to intercalation with moisture and oxygen. The simplicity and robustness of the hybrid MoS 2 –GO solid lubricant in mitigating wear-friction behavior of steel-on-steel tribopair in a multifarious environment is a game-changing and is promising for various applications.

36 MATERIALS SCIENCE↗

Identification of the active complex for CO oxidation over single-atom Ir-on-MgAl2O4 catalysts

Supported single atoms provide the best utilization of noble metals and provide an opportunity to design new heterogeneous catalysts. However, identification of the active single atoms structure is required for understanding the reaction mechanism and guiding catalyst design. We used in-situ infrared spectroscopy, in-operando x-ray adsorption spectroscopy and quantum chemical calculations to show that Ir(CO)/MgAl2O4 is the active single atom complex for low temperature CO oxidation and Ir(CO)(O) is the most stable intermediate. In contrast to poisoning of nanoparticles by CO, the formation of Ir(CO) on single atoms results in a different reaction mechanism and high activity for low temperature CO oxidation. This is due to the ability of single atoms to coordinate with multiple ligands, where CO, in Ir(CO)(O), acts as a facilitator by lowering the reaction barrier between gas phase CO and adsorbed O (Eley-Rideal mechanism).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Revealing the electronic structure of the current-induced metastable state in 1T-TaS 2

Among the key features for next-generation memory devices is the need for high-contrast switching between metallic and insulating states with fast switching speed and long lifetime. However, materials exhibiting such properties are rare, and their electronic structure is often poorly understood. Here, by combining state-of-the-art devices with angle-resolved photoemission spectroscopy, we study the emergence of a metastable metallic state from the insulating ground state in the charge-density wave (CDW) material 1T-TaS 2 after applying short current pulses. Analysis of the electronic structure suggests a picture in which 1T-TaS 2 transforms from a band insulator in the commensurate CDW ground state to a correlated metal in the metastable state. Moreover, the optically induced metastable state reveals a strong similarity to the current-induced one. This work provides an extensive characterization of metastable order in 1T-TaS 2 and proves how studying electronic properties under in-operando conditions is a critical step for next-generation devices.

Huber, Maximilian [Lawrence Berkeley National Labo↗

Nanoscale Li, Na, and K ion-conducting polyphosphazenes by atomic layer deposition

A key trailblazer in the development of thin-film solid-state electrolytes has been lithium phosphorous oxynitride (LiPON), the success of which has led to recent progress in thin-film ion conductors. Here we compare the structural, electrochemical, and processing parameters between previously published LiPON and NaPON ALD processes with a novel ALD process for the K analogue potassium phosphorous oxynitride (KPON). In each ALD process, alkali tert-butoxides and diethylphosphoramidate are used as precursors. To understand the ALD surface reactions, this work proposes a reaction mechanism determined by in-operando mass spectrometry for the LiPON process as key to understanding the characteristics of the APON (A = Li, Na, K) family. As expected, NaPON and LiPON share similar reaction mechanisms as their structures are strikingly similar. KPON, however, exhibits similar ALD process parameters but the resulting film composition is quite different, showing little nitrogen incorporation and more closely resembling a phosphate glass. Due to the profound difference in structure, KPON likely undergoes an entirely different reaction mechanism. Furthermore, this paper presents a comprehensive summary of ALD ion conducting APON films as well as a perspective that highlights the versatility of ALD chemistries as a tool for the development of novel thin film ion-conductors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Design and optimization of a modular setup for measurements of three-dimensional spin polarization with ultrafast pulsed sources

ULTRASPIN is an apparatus devoted to the measurement of the spin polarization (SP) of electrons ejected from solid surfaces in a UHV environment. It is designed to exploit ultrafast light sources (free electron laser or laser high harmonic generation) and to perform (photo)electron spin analysis by an arrangement of Mott scattering polarimeters that measure the full SP vector. The system consists of two interconnected UHV vessels: one for surface science sample cleaning treatments, e-beam deposition of ultrathin films, and low energy electron diffraction/AES characterization. The sample environment in the polarimeter allows for cryogenic cooling and in-operando application of electric and magnetic fields. The photoelectrons are collected by an electrostatic accelerator and transport lens that form a periaxial beam that is subsequently directed by a Y-shaped electrostatic deflector to either one of the two orthogonal Mott polarimeters. The apparatus has been designed to operate in the extreme conditions of ultraintense single-X-ray pulses as originated by free electron lasers (up to 1 kHz), but it allows also for the single electron counting mode suitable when using statistical sources such as synchrotron radiation, cw-laser, or e-gun beams (up to 150 kcps).

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Toyota beamline (BL33XU) at SPring-8

The Toyota beamline (BL33XU) at SPring-8 is an undulator beamline developed to assist in the study of various automotive-related materials. The light source is a tapered in-vacuum undulator that provides a variable energy band width as well as a high brilliance X-ray beam. Two different optical arrangements are available: Optics 1 and Optics 2. Optics 1 is dedicated to time-resolved X-ray absorption spectroscopy (XAFS), and consists of two channel-cut crystal monochromators and four water-cooled flat Si mirrors. The Si(111) and Si(220) monochromator crystals cover an energy range of 4.0–46.0 keV and are driven by high-speed AC servo motors. These monochromators, in conjunction with the tapered undulator, enable high-quality XAFS data acquisition with a temporal resolution of 10 ms. Optics 2 is optimized for X-ray diffraction, scattering and imaging and includes a recently installed double crystal monochromator, two water-cooled flat Si mirrors and Kirkpatrick-Baez (KB) focusing mirrors. The monochromator incorporates parallel mounted Si(111) and Si(311) crystals and covers an energy range of 4.5–70 keV. The beamline provides two experimental stations: Exp. Hutch 2 and Exp. Hutch 3. The gas supply system and mass spectrometers installed in Exp. Hutch 2 allow in-operando measurements under various atmospheres. The scanning three-dimensional X-ray diffraction (scanning 3DXRD) microscopy instrumentation developed and installed in Exp. Hutch 3 enables non-destructive orientation and stress mapping of 1 mm-thick steel specimens using a high energy microbeam.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Microscopic piezoelectric behavior of clamped and membrane (001) PMN-30PT thin films

Bulk single-crystal relaxor-ferroelectrics, like Pb(Mg 1/3 Nb 2/3 )O- 3 -PbTiO 3 (PMN-PT), are widely known for their large piezoelectricity. This is attributed to polarization rotation, which is facilitated by the presence of various crystal symmetries for compositions near a morphotropic phase boundary. Relaxor-ferroelectric thin films, which are necessary for low-voltage applications, suffer a reduction in their piezoelectric response due to clamping by the passive substrate. To understand the microscopic behavior of this adverse phenomenon, we employ the AC electric field driven in-operando synchrotron x-ray diffraction on patterned device structures to investigate the piezoelectric domain behavior under an electric field for both a clamped (001) PMN-PT thin film on Si and a (001) PMN-PT membrane released from its substrate. In the clamped film, the substrate inhibits the field-induced rhombohedral (R) to tetragonal (T) phase transition resulting in a reversible R to Monoclinic (M) transition with a reduced longitudinal piezoelectric coefficient d 33 < 100 pm/V. Releasing the film from the substrate results in recovery of the R to T transition and results in a d 33 > 1000 pm/V. Here, using diffraction with spatial mapping, we find that lateral constraints imposed by the boundary between the active and inactive materials also inhibit the R to T transition. Phase-field calculations on both clamped and released PMN-PT thin films simulate our experimental findings. Resolving the suppression of thin film piezoelectric response is critical to their application in piezo-driven technologies.

36 MATERIALS SCIENCE↗

Low temperature recovery of OFF-state stress induced degradation of AlGaN/GaN high electron mobility transistors

Thermal annealing is a widely used strategy to enhance semiconductor device performance. However, the process is complex for multi-material multi-layered semiconductor devices, where thermoelastic stresses from lattice constant and thermal expansion coefficient mismatch may create more defects than those annealed. We propose an alternate low temperature annealing technique, which utilizes the electron wind force (EWF) induced by small duty cycle high density pulsed current. To demonstrate its effectiveness, we intentionally degrade AlGaN/GaN high electron mobility transistors (HEMTs) with accelerated OFF-state stressing to increase ON-resistance ∼182.08% and reduce drain saturation current ∼85.82% of pristine condition at a gate voltage of 0 V. We then performed the EWF annealing to recover the corresponding values back to ∼122.21% and ∼93.10%, respectively. The peak transconductance, degraded to ∼76.58% of pristine at the drain voltage of 3 V, was also recovered back to ∼92.38%. This recovery of previously degraded transport properties is attributed to approximately 80% recovery of carrier mobility, which occurs during EWF annealing. We performed synchrotron differential aperture x-ray microscopy measurements to correlate these annealing effects with the lattice structural changes. We found a reduction of lattice plane spacing of (001) planes and stress within the GaN layer under the gate region after EWF annealing, suggesting a corresponding decrease in defect density. Application of this low-temperature annealing technique for in-operando recovery of degraded electronic devices is discussed.

Physics↗

Recent applications of hard x-ray photoelectron spectroscopy

Recent applications of hard x-ray photoelectron spectroscopy (HAXPES) demonstrate its many capabilities in addition to several of its limitations. Examples are given, including measurement of buried interfaces and materials under in situ or in operando conditions, as well as measurements under x-ray standing-wave and resonant excitation. Physical considerations that differentiate HAXPES from photoemission measurements utilizing soft x-ray and ultraviolet photon sources are also presented.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Spatiotemporal characterization of the field-induced insulator-to-metal transition

Watching a metal filament grow Resistive switching is a process in which the electrical resistance of a sample changes abruptly in response to a voltage pulse, often by orders of magnitude. This process is at the heart of many neuromorphic computing approaches but visualizing it in both space and time is tricky. del Valle et al . monitored the resistive switching in three different vanadium oxide compounds by measuring time- and space-resolved optical reflectivity (see the Perspective by Hilgenkamp and Gao). A characteristic conducting filament was quickly nucleated on the inhomogeneities in the sample and then propagated due to Joule heating. —JS

Science & Technology - Other Topics↗

Morphological Evolution and Dealloying During Corrosion of Ni20Cr (wt.%) in Molten FLiNaK Salts

The dealloying corrosion behavior of the FCC Ni20Cr (wt%) in molten LiF-NaF-KF (FLiNaK) salts at 600 °C under varying applied potentials was investigated. Using in-operando electrochemical techniques and a multi-modal suite of characterization methods, we connect electrochemical potential, thermodynamic stability, and electro-dissolution kinetics to the corrosion morphologies. Notably, under certain potential regimes, a micron-scale bicontinuous structure, characterized by a network of interconnected pores and ligaments riched with the composition of the more noble (MN) element, becomes prominent. At other potentials both MN and less noble (LN) elements dealloy but at different rates. The dealloying process consists of lattice and grain boundary diffusion of Cr to the metal/salt interface, interphase Cr oxidation, accompanied by surface diffusion of Ni to form interconnected ligaments. At higher potentials, the bicontinuous porous structure undergoes further surface coarsening. Concurrently, Cr(II), Cr(III), and Ni(II) begin to dissolve, with the dissolution of Ni occurring at a significantly slower rate. When solid-state transport of Cr is exceeded by the interfacial rates, dealloying depths are limited.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

18-ID (FXI) Beamline Radiation Shielding Analysis

The18-ID beamline is a Full Field X-ray Imaging (FXI) beamline capable of imaging 3D in-situ and in-operando dynamics of sample morphology and oxidation states at 30 nm spatial resolution. The source of this beamline is a high-flux hard x-ray damping wiggler (DW100). The radiation shielding analysis of this beamline is described in this report.

36 MATERIALS SCIENCE↗

Early Career: In-situ Monitoring of Dynamic Phenomena during Solidification

Solidification is critical to processes like casting and additive manufacturing and the manufacture of metallic alloy components we use in our everyday lives. State-of-the-art characterization techniques, now available at U.S. DOE User Facilities and in the laboratory, are not only enabling fundamental studies of metallic alloy solidification dynamics, but also in-operando, in-situ deformation, and manufacturing studies. Here we use x-ray, proton, and electron imaging to study solidification dynamics from the micro-scale to the macro-scale, at times ranging from microseconds to minutes. Our experimental results are used to inform, develop, and validate computational models at the same length and time-scales. Integrating in-situ characterization and modeling will yield the prediction and control of metallic alloy solidification dynamics and the creation of microstructures and properties by design with advanced manufacturing. Major research accomplishments during this period include: 1. Exploring dynamical microstructure selection by means of real-time synchrotron x-ray imaging of controlled directional solidification of aluminum alloys and quantitative phase field modeling. 2. In-situ and ex-situ electron microscopy of rapid solidification after laser melting of metallic alloys. 3. Exploring the impact of microstructural heterogeneities that develop during solidification on solid-state phase transitions, with an emphasis on phase growth, (meta)stability, and transition pathways in aluminum alloys. 4. Demonstrations of four-dimensional (three-dimensions plus time) x-ray microscopy during controlled directional solidification and the first quasi-static/dynamic transmission high energy electron microscopy of metallic alloy solidification dynamics. 5. Experiments and modeling of solidification structure evolution and forward modeling and testing of micromechanical behavior.

36 MATERIALS SCIENCE↗

Understanding Soot Development and Thermal Stratification in Combustion Engines through Hyperspectral Non-linear Optical Diagnostics Development

Progress towards next-generation internal combustion engine technologies is dramatically hindered by the complexity of both simulating and measuring key processes, such as thermal stratification and soot formation, in an operating prototype. In general, spectroscopic methods for in-operando probing become limitingly complex at the high pressures and temperature encountered in such systems, and numerical methods for simulating device performance become computationally expensive due to the turbulent flow field, detailed chemistry, and range of important length-scales involved. This report presents parallel experimental and theoretical advances to conquer these limitations. We report the development of high pressure and high temperature ultrafast coherent anti-Stokes Raman spectroscopy measurements, up to a pressure and temperature regime relevant to engine conditions. This report also presents theoretical results using a stochastic one-dimensional turbulence (ODT) model providing insight into the local thermochemical state and its consequences by resolving the full range of reaction-diffusion scales in a stochastic model.

36 MATERIALS SCIENCE↗

EFRC-MUSE: Multi-Scale Fluid-Solid Interactions in Architected and Natural Materials

Phase interactions and fluid properties in geological and other environments are critical in applications ranging from hydrogen production and geologic storage and recovery, carbon dioxide storage and sequestration, and the sustainable use of water resources. The four goals of EFRC-MUSE: Multi-Scale Fluid-Solid Interactions in Architected and Natural Materials were based on the priority directions articulated in the Basic Research Needs documents, and the scientific needs in nanoscience. 1. Develop a fundamental understanding of confinement and surface interactions in mesoscale media with nanometer-sized pores on the phase behavior, thermodynamic and multiphase flow properties of multicomponent fluid mixtures. 2. Examine the impact of mineralogy and material heterogeneity on mechanical properties to better understand chemo-mechanical interactions in material failure. 3. Determine in-operando cross-scale structural and nanostructural material properties with fluids in confinement and flow under realistic condi

58 GEOSCIENCES↗

Phase Evolution and Textural Changes during the Direct Conversion and Storage of CO 2 to Produce Calcium Carbonate from Calcium Hydroxide

The increasing use of energy resources recovered from subsurface environments and the resulting carbon imbalance in the environment has motivated the need to develop thermodynamically downhill pathways to convert and store CO 2 as water-insoluble calcium or magnesium carbonates. While previous studies extensively explored aqueous routes to produce calcium and magnesium carbonates from CO 2 , there is limited scientific understanding of the phase evolution and textural changes during the direct gas–solid conversion routes to produce calcium carbonate from calcium hydroxide, which is one of the abundant constituents of alkaline industrial residues. With increasing interest in developing integrated pathways for capturing, converting, and storing CO 2 from dilute flue gases, understanding the composition of product phases as they evolve is essential for evaluating the efficacy of a given processing route. Therefore, in this study, we investigate the phase evolution and the corresponding textural changes as calcium hydroxide is converted to calcium carbonate under the continuous flow of CO 2 at an ambient pressure of 1 atm with continuous heating from 30 °C to 500 °C using in-operando wide angle X-ray scattering (WAXS), small angle X-ray scattering (SAXS), and ultrasmall angle X-ray scattering (USAXS) measurements.

Liu, Meishen↗

Advances in Neutron Radiography: Application to Additive Manufacturing Inconel 718

Reactor-based neutron radiography is a non-destructive, non-invasive characterization technique that has been extensively used for engineering materials such as inspection of components, evaluation of porosity, and in-operando observations of engineering parts. Neutron radiography has flourished at reactor facilities for more than four decades and is relatively new to accelerator-based neutron sources. Recent advances in neutron source and detector technologies, such as the Spallation Neutron Source (SNS) at the Oak Ridge National Laboratory (ORNL) in Oak Ridge, TN, and the microchannel plate (MCP) detector, respectively, enable new contrast mechanisms using the neutron scattering Bragg features for crystalline information such as average lattice strain, crystalline plane orientation, and identification of phases in a neutron radiograph. Additive manufacturing (AM) processes or 3D printing have recently become very popular and have a significant potential to revolutionize the manufacturing of materials by enabling new designs with complex geometries that are not feasible using conventional manufacturing processes. However, the technique lacks standards for process optimization and control compared to conventional processes. Residual stresses are a common occurrence in materials that are machined, rolled, heat treated, welded, etc., and have a significant impact on a component s mechanical behavior and durability. They may also arise during the 3D printing process, and defects such as internal cracks can propagate over time as the component relaxes after being removed from its build plate (the base plate utilized to print materials on). Moreover, since access to the AM material is possible only after the component has been fully manufactured, it is difficult to characterize the material for defects a priori to minimize expensive re-runs. Currently, validation of the AM process and materials is mainly through expensive trial-and-error experiments at the component level, whereas in conventional processes the level of confidence in predictive computational modeling is high enough to allow process and materials optimization through computational approaches. Thus, there is a clear need for non-destructive characterization techniques and for the establishment of processing- microstructure databases that can be used for developing and validating predictive modeling tools for AM.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗