Search NASA⌕ Search

SEARCH · Search NASA

Results for “Irradiation Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Postirradiation examination from separate effects irradiation testing of uranium nitride kernels and coated particles

An overview of postirradiation examination results for uranium nitride kernels and uranium nitride coated particles irradiated in the High Flux Isotope Reactor are presented. This is the first postirradiation examination of the MiniFuel irradiation vehicle that was recently developed to rapidly accumulate burnup during separate effects irradiation testing. In general, the burnup and fuel temperatures measured postirradiation were consistent with the design calculations. The burnup measured by mass spectrometry ranged from 5.9 to 10 MWd/kgU and was achieved after only 68 effective full-power days of irradiation. The dilatometric evaluation of passive silicon carbide thermometry indicated that the fuel was irradiated at temperatures ranging from 410 to 460 °C. Because the irradiation temperatures and burnup were low, the UN kernels showed minimal fission gas release that was within the range of the expected recoil (athermal) release. While it is possible to measure fuel swelling using x-ray computed tomography, the observed swelling was too small to quantify in this case. Extensive microstructural characterization of the irradiated fuel was performed in this study, and no significant irradiation induced changes were observed.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Resumption of SFR Overpower Testing and Post-Transient Examination of the THOR-C-2 Irradiation Test

Transient overpower testing for fuel safety research and development has resumed at Idaho National Laboratory. The THOR-C-2 commissioning test has been performed and post-transient examination has been performed revealing the intended creep rupture failure near the top of the fuel zone. This paves the way for future testing on previously irradiated fuels that will support fuel development and qualification.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Resumption of SFR Overpower Testing and Post-Transient Examination of the THOR-C-2 Irradiation Test

Transient overpower testing for fuel safety research and development has resumed at Idaho National Laboratory. The THOR-C-2 commissioning test has been performed and post-transient examination has been performed revealing the intended failure near the top of the fuel zone. This paves the way for future testing on previously irradiated fuels that will support fuel development and qualification.

advanced reactors↗
DOE OSTI2016

Production of LEU fully ceramic microencapsulated fuel for irradiation testing

The Advanced Fuels Campaign of the US DOE Fuel Cycle Research/Development program is currently engaged in production of FCM fuel for irradiation testing in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL). FCM fuel production is a serial process with 3 major steps namely kernel, TRISO, and compact production. The first step in the kernel process is production of air-dried UO{sub 3} gel spheres with suspended carbon particles. These spheres, roughly 2 mm in size, are then calcined to produce a mixture of UO{sub 2} and carbon. This calcination step may be performed in either argon, hydrogen, or mixtures of these gases. Once the calcination step is complete, temperature is increased (>1400 Celsius degrees) to convert this mixture to UO{sub 2} + UC{sub x}. Once dense oxide-carbide kernels are available, the inert environment is switched to a nitrogen containing one to facilitate carbothermic reduction of kernels and production of UN. Essentially, the oxygen and carbon in the oxide-carbide kernels react with one another to produce CO and are replaced with nitrogen inside the lattice. The TRISO step in fuel production is incorporation of a porous carbon buffer layer, a dense inner pyrolytic carbon layer (IPyC), a SiC layer, and finally and outer pyrolytic carbon layer (OPyC) onto the UN kernels. The coating layer deposition step is carried out inside a graphite furnace using a fluidized bed chemical vapor deposition (CVD) process. In essence, a mixture of reactant and inert gasses flow from the bottom through a bed of particles that are in turn fluidized by the gas stream. The particles undergo CVD and once a different coating layer is to be incorporated, the furnace temperature is adjusted and the reactant gases are changed. The final step in the series of fuel production activities is the consolidation of UN TRISO particles inside the SiC matrix to produce cylindrical pellets. It entails 3 critical areas: SiC powder mixing, over-coating of particles, and high-temperature densification. Optimal execution of the powder mixing step is vital to achieve a fully dense SiC matrix at the end of the process. The SiC matrix is consolidated using a special form of liquid phase sintering (LPS) involving nano-powder feedstock that is designated as the NITE process. The SiC nano-powder slurry is sprayed directly onto the particle surface using a piezoelectric nozzle. Once the over-coated particles are available, final consolidation step at high temperatures (1875 Celsius degrees) is carried out.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Separate effects irradiation testing of miniature fuel specimens

We report that qualification of new nuclear fuels is necessary for their deployment and requires a thorough understanding of fuel behavior under irradiation. Traditionally, nuclear fuels have been qualified by performing exhaustive integral tests under a limited range of prototypic conditions designed for their specific reactor application. While some integral fuel testing is essential, basic data on behavior and property evolution under irradiation can be obtained from separate effects tests. These irradiations could offer reduced cost, reduced complexity, and in the case of accelerated testing, reduced time to achieve a given burnup. Furthermore, it may be desirable to design test irradiations capable of deconvoluting the myriad effects of burnup, temperature gradients, and other factors inherent to integral irradiation tests. Oak Ridge National Laboratory has developed an experimental capability to perform separate effects irradiation testing of miniature fuel specimens in the High Flux Isotope Reactor (HFIR): the “MiniFuel” irradiation vehicle. The small size (<4 mm 3 ) of the fuel specimens simplifies the design, analysis, and post-irradiation examination. By reducing the fuel mass, the total heat generated inside the experiment vehicle can be dominated by gamma heating in the structural materials instead of fission heating in the fuel. This essentially decouples the fuel temperature from the fission rate, allowing for highly accelerated testing (3X-18X the burnup rate of a typical light water reactor for 235 U enrichments varying from 0.22 wt% to 8 wt%) and an extremely flexible experiment design that can accommodate a wide range of fuel temperatures (~100 °C to >1200 °C), compositions, enrichments, and even geometries without requiring detailed analyses for each fuel variant. In conclusion, this paper summarizes the experiment design concept, evaluates potential applications for specific fuel forms, and briefly describes the first set of experiments on uranium nitride kernels that have been assembled and are currently being irradiated in the HFIR.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

2024 NSUF User Development Workshop on Irradiation Testing

Monday, May 20 – Thursday, May 23, 2024 at Center for Advanced Energy Studies at Idaho National Laboratory, Idaho Falls, Idaho. This pilot workshop was hosted to expand the NSUF user community and introduce irradiation testing of nuclear fuel and materials to new researchers, and to build long-term relationships between the NSUF program office, NSUF partner facilities, and NSUF university-affiliated users to provide better utilization of NSUF resources in addressing United States energy challenges.

Starks, Alexis↗
NASA NTRS1976

High intensity solar irradiation testing of UV optics

The Orbiting Solar Observatory-I (OSO-8 in orbit) incorporates two high resolution solar pointing spectrometers operating from 1000 A to 4000 A. Energy from the sun enters a Cassegrainian telescope and is focused on a slit while the solar disk is scanned to one arc-second resolution. The stability of the secondary mirrors reflectance was of concern since they would be exposed to intense focused solar energy up to 27 suns. A test program was initiated to simulate this energy input on sample UV mirrors of the MgF2 and LiF types and to evaluate their performance after irradiation. Tests were conducted to simulate the solar spectrum at high intensities (25 suns) and at a single wavelength near Lyman-alpha, but with twenty times the solar intensity at Lyman-alpha. Post-test measurements after every exposure were made at wavelengths from 1025 A to 1849 A. After 75 simulated 'orbits', reflectance changes due to temperature effects were noted to be less than 10%. Reductions in reflectance under high intensity solar radiation were generally greater than 10%. Polymerization of surface contaminations on the LiF mirrors reduced reflectances at short wavelengths by 40%.

Greyerbiehl, J. M.↗
DOE OSTI2016

Irradiation test about oxidation-resistant graphite in WWR-K research reactor - 18533

Graphite materials are used for the in-core components of High Temperature Gas-cooled Reactor (HTGR). It is desirable to enhance oxidation resistance of graphite to keep much safety margin. SiC coating is the candidate method for this purpose. JAEA and four Japanese graphite companies, Toyo Tanso, Ibiden, Tokai Carbon and Nippon Techno-Carbon are studying to develop oxidation-resistant graphite for the in-core components. Neutron irradiation test with two capsules was carried out by WWR-K research reactor of Institute of Nuclear Physics of the Republic of Kazakhstan (INP) through the International Science and Technology Center (ISTC) partner project. The total irradiation cycles of WWR-K operation was 10 cycles and the total duration was 200 days. Irradiation temperature about 1473 K would be attained. The maximum fast neutron fluence (E>0.18 MeV) for the gas-swept capsule irradiated at a central irradiation hole was preliminary calculated as 1.2x10{sup 25} m{sup -2}, and for the sealed capsule at a peripheral irradiation hole as 4.2x10{sup 24} m{sup -2}. Dimension and weight of the irradiated specimens were measured, and outer surface of the specimens were observed by optical microscope. For the irradiated oxidation resistant graphite, out-of-pile oxidation test will be carried out at an experimental laboratory. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2020

Irradiation Tests of Superconducting Detectors and Comparison with Simulations

For the future satellite mission at the second sun–earth Lagrangian point (L2), we need to mitigate phonon propagation created by cosmic rays to superconducting detectors. We simulate phonon propagation in silicon substrate and show that putting a metal layer on the substrate or making hole in the substrate reduces the propagation. We also show a function which shows the response of a TES bolometer on a substrate. To validate these theoretical expectations, we make irradiation tests using two types of superconducting detectors: transition edge sensor bolometers and kinetic inductance detectors. From the tests, we show that putting metal can reduce correlations between detectors and number of hit events from charged particles.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

Accelerated Fuel Qualification of Fast Modular Reactor Fuel in a Thermal Reactor: Modeling and Simulation Paired with Irradiation Testing

The accelerated fuel qualification (AFQ) methodology is applied by simulating accelerated fuel tests of the General Atomics Electromagnetic Systems’ fuel system for its 44-MW(electric) gas-cooled, fast-spectrum fast modular reactor (FMR). This fuel is comprised of UO 2 pellets in SiGA® cladding, a silicon carbide ceramic matrix composite. Fast reactors, like the FMR, offer many benefits, including high fuel utilization and flexibility, but may require a lengthy material design process if tests are performed using fast neutron irradiation alone. A thermal neutron irradiation can instead be used to rapidly test how well key components of the current material models extend to high burnup. Thermal neutrons produce a different radial power distribution within the pin than fast neutrons. However, the temperature and burnup values for the two neutron types are comparable, and the differences between the simulated fuel responses are relatively small, demonstrating the weak sensitivity of the physics-based fuel model calculations on the neutron type and the irradiation rate. Furthermore, the deformation of the SiGA cladding saturates after about 1 displacement per atom for both neutron spectra. In an accelerated fuel test, the irradiation time required to reach the target fuel burnup can be reduced by a factor of 3 by using a small rodlet with a 45% smaller pellet diameter while maintaining the same linear power. Therefore, the time for data collection up to high burnup can be significantly reduced while maintaining the same temperature profile, which largely determines the material response. Tests of fuel rodlets of standard and compact size will be carried out in the Idaho National Laboratory’s Advanced Test Reactor (ATR), including full size and compact rodlets with varying gap sizes. By applying physics-based mechanistic modeling and simulation in accordance with the AFQ methodology, this type of compact rodlet testing in a thermal test reactor captures the necessary phenomena to test fuel material models up to high burnup and to simulate the expected impact of fast neutron radiation on the fuel in FMR operations. Finally, this approach to testing fast reactor fuels in existing thermal test reactors, paired with advanced physics-based mechanistic modeling and simulation, is expected to be applicable to a range of advanced fuels and will decrease the overall fuel qualification timeframe from decades to years.

Advanced test reactor (ATR)↗
DOE OSTI2026

Results of the AGR-5/6/7 UCO TRISO fuel irradiation test in the Advanced Test Reactor

AGR-5/6/7 was the last in a series of irradiation experiments sponsored by the U.S. Department of Energy in support of the development and qualification of TRISO coated particle fuel for use in a high-temperature gas-cooled reactor. This experiment was conducted to verify the performance of the reference-design TRISO-coated low-enriched UCO fuel for modular high-temperature gas-cooled reactor normal operating conditions and to explore fuel performance at temperatures substantially beyond those typical of normal operation. A total of 194 UCO fuel compacts in five capsules were irradiated in the Advanced Test Reactor for 360.9 effective full-power days, achieving final burnup ranging from 5.66% to 15.26% fissions per initial heavy metal atom and fast neutron fluence ranging from 1.62 × 10 25 to 5.55 × 10 25 n/m 2 (E > 0.18 MeV). Calculated time-averaged fuel temperatures ranged from 467 °C to 1432 °C, with a peak fuel temperature of 1536 °C. During the first five irradiation cycles (∼180 effective full-power days), 85m Kr fission gas release-rate-to-birth-rate ratios were 10 −7 –10 −6 , indicating no particle failures. Near the end of the sixth cycle, a substantial number of in-pile particle failures occurred in Capsule 1. The fission gas release from this capsule impacted the readings from the other four capsules and led to unreliable fission gas release measurements for all capsules during the last four cycles. A preliminary post-irradiation examination of Capsule 1 fuel and internal components revealed the in-pile particle failures resulted from operational issues with the capsule, not subpar performance of the fuel particles.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2015

Design of Irradiation Tests for Monolithic Fuel Qualification

The US fuel development team is focused on developing and qualifying the uranium-molybdenum monolithic fuel. Several previous irradiations have demonstrated the favorable behavior of the monolithic fuel. The overall irradiation program strategy was recently revamped to provide an opportunity to test, examine, and select the most advantageous fabrication processes for producing monolithic fuel. Specimens fabricated by the selected processes are planned to be irradiated in a series of tests in order to populate the data set needed for fuel qualification through the Nuclear Regulatory Commission. This paper summarizes the overall irradiation testing plan with an emphasis on the rigorous approach to design, analysis, and requirements for qualification tests. The recently designed Full Size Plate 1 irradiation test is also summarized as an example of this strategic approach to qualifying monolithic fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2016

AGR 3/4 Irradiation Test Final As Run Report, Revision 1

Several fuel and material irradiation experiments have been planned for the Idaho National Laboratory Advanced Reactor Technologies Technology Development Office Advanced Gas Reactor Fuel Development and Qualification Program (referred to as the INL ART TDO/AGR fuel program hereafter), which supports the development and qualification of tristructural-isotropic (TRISO) coated particle fuel for use in HTGRs. The goals of these experiments are to provide irradiation performance data to support fuel process development, qualify fuel for normal operating conditions, support development and validation of fuel performance and fission product transport models and codes, and provide irradiated fuel and materials for post irradiation examination and safety testing (INL 05/2015). AGR-3/4 combined the third and fourth in this series of planned experiments to test TRISO coated low enriched uranium (LEU) oxycarbide fuel. This combined experiment was intended to support the refinement of fission product transport models and to assess the effects of sweep gas impurities on fuel performance and fission product transport by irradiating designed-to-fail fuel particles and by measuring subsequent fission metal transport in fuel-compact matrix material and fuel-element graphite. The AGR 3/4 fuel test was successful in irradiating the fuel compacts to the burnup and fast fluence target ranges, considering the experiment was terminated short of its initial 400 EFPD target (Collin 2015). Out of the 48 AGR-3/4 compacts, 42 achieved the specified burnup of at least 6% fissions per initial heavy-metal atom (FIMA). Three capsules had a maximum fuel compact average burnup < 10% FIMA, one more than originally specified, and the maximum fuel compact average burnup was <19% FIMA for the remaining capsules, as specified. Fast neutron fluence fell in the expected range of 1.0 to 5.5 × 10 25 n/m 2 (E >0.18 MeV) for all compacts. In addition, the AGR-3/4 experiment was globally successful in keeping the temperature in the twelve capsules relatively flat in a range of temperatures suitable for the measurement of fission product diffusion in compact matrix and structural graphite materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2017

Technology Implementation Plan: Irradiation Testing and Qualification for Nuclear Thermal Propulsion Fuel

This document is a notional technology implementation plan (TIP) for the development, testing, and qualification of a prototypic fuel element to support design and construction of a nuclear thermal propulsion (NTP) engine, specifically its pre-flight ground test. This TIP outlines a generic methodology for the progression from non-nuclear out-of-pile (OOP) testing through nuclear in-pile (IP) testing, at operational temperatures, flows, and specific powers, of an NTP fuel element in an existing test reactor. Subsequent post-irradiation examination (PIE) will occur in existing radiological facilities. Further, the methodology is intended to be nonspecific with respect to fuel types and irradiation or examination facilities. The goals of OOP and IP testing are to provide confidence in the operational performance of fuel system concepts and provide data to program leadership for system optimization and fuel down-selection. The test methodology, parameters, collected data, and analytical results from OOP, IP, and PIE will be documented for reference by the NTP operator and the appropriate regulatory and oversight authorities. Final full-scale integrated testing would be performed separately by the reactor operator as part of the preflight ground test.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Relevance of Tritium Breeder Irradiation Testing in a Fusion Prototypic Neutron Source

A fusion prototypic neutron source (FPNS) will play a fundamental role in testing and developing fusion materials that can withstand the harsh fusion environment. We conducted a thorough assessment to determine whether blanket materials would benefit from FPNS testing. Because of the cross sections for the various blanket materials, lithium-containing materials can generally be tested adequately using existing fission irradiation capabilities instead of waiting for or relying solely on future FPNS experiments. However, non-lithium blanket materials, such as beryllium multipliers and flow channel inserts, should be tested under a fusion neutron spectrum.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Irradiation Testing of Sensors - ASI Program Review 2022

This is a powerpoint presentation for the annual Advanced Sensors and Instrumentation (ASI) program webinar. The following is a summary of the presentation. Advanced instrumentation enables testing of nuclear fuels and materials in support of the US advanced nuclear technology industry. A number of promising sensor technologies are in the pipeline. The early part of sensor development can be done outside of the reactor environment, but full technical readiness requires experience gained from in-core performance testing. Customers usually have only one shot to conduct their irradiation experiments. Because of the high costs test sponsors are frequently reluctant to incorporate unproven technologies in reactor experiments. Therefore, it is vital to demonstrate newly-developed sensors in operational conditions, prior to incorporating them into long-term high-value experiments. Successful completion of these activities will create new monitoring capabilities in high-power test reactors (such as ATR) as well as specialty reactors such as TREAT.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
NASA NTRS1975

Design, fabrication, and operation of capsules for the irradiation testing of candidate advanced space reactor fuel pins

Fuel irradiation experiments were designed, built, and operated to test uranium mononitride (UN) fuel clad in tungsten-lined T-111 and uranium dioxide fuel clad in both tungsten-lined T-111 and tungsten-lined Nb-1% Zr. A total of nine fuel pins was irradiated at average cladding temperatures ranging from 931 to 1015 C. The UN experiments, capsules UN-4 and -5, operated for 10,480 and 10,037 hr, respectively, at an average linear heat generation rate of 10 kW/ft. The UO2 experiment, capsule UN-6, operated for 8333 hr at an average linear heat generation rate of approximately 5 kW/ft. Following irradiation, the nine fuel pins were removed from their capsules, externally examined, and sent to the NASA Plum Brook Facility for more detailed postirradiation examination. During visual examination, it was discovered that the cladding of the fuel pin containing dense UN in each of capsules UN-4 and -5 had failed, exposing the UN fuel to the NaK in which the pins were submerged and permitting the release of fission gas from the failed pins. A rough analysis of the fission gas seen in samples of the gas in the fuel pin region indicated fission gas release-to-birth rates from these fuel pins in the range of .00001.

Thoms, K. R.↗