Search NASA⌕ Search

SEARCH · Search NASA

Results for “Isolated Rotor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

An experimental and analytical investigation of stall effects on flap-lag stability in forward flight

Experiments have been performed with a 1.62 m diameter hingeless rotor in a wind tunnel to investigate flap-lag stability of isolated rotors in forward flight. The three-bladed rotor model closely approaches the simple theoretical concept of a hingeless rotor as a set of rigid, articulated flap-lag blades with offset and spring restrained flap and lag hinges. Lag regressing mode stability data was obtained for advance ratios as high as 0.55 for various combinations of collective pitch and shaft angle. The prediction includes quasi-steady stall effects on rotor trim and Floquet stability analyses. Correlation between data and prediction is presented and is compared with that of an earlier study based on a linear theory without stall effects. While the results with stall effects show marked differences from the linear theory results, the stall theory still falls short of adequate agreement with the experimental data.

Nagabhushanam, J.↗
NASA NTRS1997

The Development of a Tool for Semi-Automated Generation of Structured and Unstructured Grids about Isolated Rotorcraft Blades

The grid generation used to model rotorcraft configurations for Computational Fluid Dynamics (CFD) analysis is highly complicated and time consuming. The highly complex geometry and irregular shapes encountered in entire rotorcraft configurations are typically modeled using overset grids. Another promising approach is to utilize unstructured grid methods. With either approach the majority of time is spent manually setting up the topology. For less complicated geometries such as isolated rotor blades, less time is obviously required. This paper discusses the capabilities of a tool called Rotor blade Optimized Topology Organizer and Renderer(ROTOR) being developed to quickly generate block structured grids and unstructured tetrahedral grids about isolated blades. The key algorithm uses individual airfoil sections to construct a Non-Uniform Rational B-Spline(NURBS) surface representation of the rotor blade. This continuous surface definition can be queried to define the block topology used in constructing a structured mesh around the rotor blade. Alternatively, the surface definition can be used to define the surface patches and grid cell spacing requirements for generating unstructured surface and volume grids. Presently, the primary output for ROTOR is block structured grids using 0-H and H-H topologies suitable for full-potential solvers. This paper will discuss the present capabilities of the tool and highlight future work.

Shanmugasundaram, Ramakrishnan↗
NASA NTRS1996

Turbulent Inflow Measurements

In the present research, tilt rotor aeroacoustics have been studied experimentally and computationally. Experimental measurements were made on a 1/12.5 scale model. A dimensional analysis showed that the model was a good aeroacoustic approximation to the full-scale aircraft, and scale factors were derived to extrapolate the model measurements to the full-scale XV-15. The experimental measurements included helium bubble flow visualization, silk tuft flow visualization, 2-component hot wire anemometry, 7-hole pressure probe measurements, vorticity measurements, and outdoor far field acoustic measurements. The hot wire measurements were used to estimate the turbulence statistics of the flow field into the rotors, such as length scales, velocity scales, dissipation, and turbulence intermittency. To date, these flow measurements are the only ones in existence for a hovering tilt rotor. Several different configurations of the model were tested: (1) standard configurations (single isolated rotor, two rotors without the aircraft, standard tilt rotor configuration); (2) flow control devices (the 'plate', the 'diagonal fences'); (3) basic configuration changes (increasing the rotor/rotor spacing, reducing the rotor plane/wing clearance, operating the rotors out of phase). Also, an approximation to Sikorsky's Variable Diameter Tilt Rotor (VDTR) configuration was tested, and some flow measurements were made on a semi-span configuration of the model. Acoustic predictions were made using LOWSON.M, a Mathematica code. This hover prediction code, from HOVER.FOR, used blade element theory for the aerodynamics, and Prandtl's Vortex theory to model the wake, along with empirical formulas for the effects of Reynolds number, Mach number, and stall. Aerodynamic models were developed from 7-hole pressure probe measurements of the mean velocity into the model rotors. LOWSON.M modeled a rotor blade as a single force and source/sink combination separated in the chordwise direction, at an effective blade radius. Spanwise, Mach-weighted integrals were used to find the equivalent forces and equivalent source strengths.

George, Albert R.↗
NASA NTRS1983

Acoustic measurements of a full-scale coaxial hingeless rotor helicopter

Acoustic data were obtained during a full-scale test of the XH-59A Advancing Blade Concept Technology Demonstrator in the 40- by 80-Foot Wind Tunnel. The XH-59A is a research helicopter with two coaxial rotors and hingeless blades. Performance, vibration, and noise at various forward speeds, rotor lift coefficients and rotor shaft angles of attack were investigated. The noise data were acquired over an isolated rotor lift coefficient range of 0.024 to 0.162, an advance ratio range of 0.23 to 0.45 corresponding to tunnel wind speeds of 89 to 160 knots, and angles of attack from 0 deg to 10 deg. Acoustic data are presented for seven microphone locations for all run conditions where the model noise is above the background noise. Model test configuration and performance information are also listed. Acoustic waveforms, dBA, and 1/3-octave spectra as functions of operating condition for selected data points and microphones are presented. In general, the noise level is shown to increase with rotor lift coefficient except under certain operating conditions where significant impulsive blade/vortex interactions increase noise levels.

Peterson, R. L.↗
NASA NTRS1991

Computation of rotor aerodynamic loads with a constant vorticity contour free wake model

An analytical method is presented which facilitates the study of isolated rotors with an improved approach to wake simulation. Vortex filaments are simulated along contours of constant sheet strength for the sheet of vorticity resulting from each rotor blade. Curved vortex elements comprise the filaments which can be distorted by the local velocity field. Called the Constant Vorticity Contour wake model, the approach permits the simulation of the blades' wakes corresponding to the full span of the rotor blade. The discretization of the wake of the rotor blade produces spacing and structure that are consistent with the spatial and temporal variations in the loading. A vortex-lattice aerodynamic model of the blade is also included which introduces a finite-element structural model of the blade and consideration of the force and moment trim analysis. Results of the present version of the simulation, called RotorCRAFT, are found to correlate well with H-34 flight-test data.

Quackenbush, Todd R.↗
NASA NTRS1981

Performance and loads data from a wind tunnel test of a full-scale, coaxial, hingeless rotor helicopter

A full-scale XH-59A advancing blade concept helicopter was tested in Ames Research Center's 40 by 80 foot wind tunnel. The helicopter was tested with the rotor on and off, rotor hub fairings on and off, interrotor shaft fairing on and off, rotor instrumentation module on and off, and auxiliary propulsion thrust on and off. An advance ratio range of 0.25 and 0.45 with the rotor on and from 60 to 180 knots with the rotor off was investigated. Data on aerodynamic forces and moments, rotor loads, rotor control positions and vibration for the XH-59A as well as the aerodynamic performance of the isolated rotor are presented.

Felker, F. F., III↗
NASA NTRS1987

Six-Degree-of-Freedom Vibration Suppressor

New system, total-rotor-isolation system (TRIS) employs liquid-inertia vibration-eliminator (LIVE) units, designed to isolate all six degrees of freedom of aircraft-fuselage dynamic response from continuously changing airloads developed by rotor. Vibration suppressor uses liquid mercury to damp vibrations. Results of flight tests indicated at least 95-percent reduction in vibration levels from rotor hub to pilot's seat.

Halwes, Dennis R.↗
NASA NTRS2008

Rotor Performance at High Advance Ratio: Theory versus Test

Five analytical tools have been used to study rotor performance at high advance ratio. One is representative of autogyro rotor theory in 1934 and four are representative of helicopter rotor theory in 2008. The five theories are measured against three sets of well documented, full-scale, isolated rotor performance experiments. The major finding of this study is that the decades spent by many rotorcraft theoreticians to improve prediction of basic rotor aerodynamic performance has paid off. This payoff, illustrated by comparing the CAMRAD II comprehensive code and Wheatley & Bailey theory to H-34 test data, shows that rational rotor lift to drag ratios are now predictable. The 1934 theory predicted L/D ratios as high as 15. CAMRAD II predictions compared well with H-34 test data having L/D ratios more on the order of 7 to 9. However, the detailed examination of the selected codes compared to H-34 test data indicates that not one of the codes can predict to engineering accuracy above an advance ratio of 0.62 the control positions and shaft angle of attack required for a given lift. There is no full-scale rotor performance data available for advance ratios above 1.0 and extrapolation of currently available data to advance ratios on the order of 2.0 is unreasonable despite the needs of future rotorcraft. Therefore, it is recommended that an overly strong full-scale rotor blade set be obtained and tested in a suitable wind tunnel to at least an advance ratio of 2.5. A tail rotor from a Sikorsky CH-53 or other large single rotor helicopter should be adequate for this exploratory experiment.

Harris, Franklin D.↗
NASA NTRS1997

Flow Field Around a Hovering Rotor

A lifting surface hover code developed by the Analytical Method Inc. (AMI) was used to compute the average and unsteady velocity flow field of an isolated rotor without ground effect. The predicted velocity field compares well with experimental data obtained by hot-wire anemometry and by Laser Doppler Velocimetry. A subroutine 'DOWNWASH' was written to predict the velocity field at any given point in the wake for a given blade position.

Tung, C.↗
NASA NTRS1988

Survey of Army/NASA rotorcraft aeroelastic stability research

Theoretical and experimental developments in the aeroelastic and aeromechanical stability of helicopters and tilt-rotor aircraft are addressed. Included are the underlying nonlinear structural mechanics of slender rotating beams, necessary for accurate modeling of elastic cantilever rotor blades, and the development of dynamic inflow, an unsteady aerodynamic theory for low frequency aeroelastic stability applications. Analytical treatment of isolated rotor stability in hover and forward flight, coupled rotor-fuselage stability are considered. Results of parametric investigations of system behavior are presented, and correlations between theoretical results and experimental data from small- and large-scale wind tunnel and flight testing are discussed.

Ormiston, Robert A.↗
NASA NTRS1990

The effects of structural flap-lag and pitch-lag coupling on soft inplane hingeless rotor stability in hover

A 1.62-m-diameter rotor model was tested in hover to examine the effects of structural flap-lag and pitch-lag coupling on isolated rotor blade lead-lag stability. Flap-lag coupling was introduced by inclining the principal axes of the blade structure up to 60 degrees. Pitch-lag coupling was obtained either alone or in combination with flap-lag coupling through the use of skewed flexural hinges. The principal results confirm the predictions of theory, and show that both structural flap-lag and pitch-lag coupling when used separately are beneficial to blade stability. Moreover, when the couplings are combined, the lead-lag damping is significantly greater than it would be if the individual contributions were superimposed. Pitch-flap coupling is shown to have only a minor effect on blade lead-lag damping. Differences between theory and experiment observed at zero blade pitch and flexure angles during the initial testing were determined in a second test to be caused by stand flexibility. Other differences between theory and experiment warrant further investigation.

Bousman, William G.↗
NASA NTRS2014

Open Rotor Tone Shielding Methods for System Noise Assessments Using Multiple Databases

Advanced aircraft designs such as the hybrid wing body, in conjunction with open rotor engines, may allow for significant improvements in the environmental impact of aviation. System noise assessments allow for the prediction of the aircraft noise of such designs while they are still in the conceptual phase. Due to significant requirements of computational methods, these predictions still rely on experimental data to account for the interaction of the open rotor tones with the hybrid wing body airframe. Recently, multiple aircraft system noise assessments have been conducted for hybrid wing body designs with open rotor engines. These assessments utilized measured benchmark data from a Propulsion Airframe Aeroacoustic interaction effects test. The measured data demonstrated airframe shielding of open rotor tonal and broadband noise with legacy F7/A7 open rotor blades. Two methods are proposed for improving the use of these data on general open rotor designs in a system noise assessment. The first, direct difference, is a simple octave band subtraction which does not account for tone distribution within the rotor acoustic signal. The second, tone matching, is a higher-fidelity process incorporating additional physical aspects of the problem, where isolated rotor tones are matched by their directivity to determine tone-by-tone shielding. A case study is conducted with the two methods to assess how well each reproduces the measured data and identify the merits of each. Both methods perform similarly for system level results and successfully approach the experimental data for the case study. The tone matching method provides additional tools for assessing the quality of the match to the data set. Additionally, a potential path to improve the tone matching method is provided.

Bahr, Christopher J.↗
NASA NTRS1988

Rotorcraft aeroelastic stability

Theoretical and experimental developments in the aeroelastic and aeromechanical stability of helicopters and tilt-rotor aircraft are addressed. Included are the underlying nonlinear structural mechanics of slender rotating beams, necessary for accurate modeling of elastic cantilever rotor blades, and the development of dynamic inflow, an unsteady aerodynamic theory for low-frequency aeroelastic stability applications. Analytical treatment of isolated rotor stability in hover and forward flight, coupled rotor-fuselage stability in hover and forward flight, and analysis of tilt-rotor dynamic stability are considered. Results of parametric investigations of system behavior are presented, and correlation between theoretical results and experimental data from small and large scale wind tunnel and flight testing are discussed.

Ormiston, Robert A.↗
NASA NTRS1996

Tilt Rotor Aircraft Aeroacoustics

A fleet of civil tilt rotor transports offers a means of reducing airport congestion and point-to-point travel time. The speed, range, and fuel economy of these aircraft, along with their efficient use of vertiport area, make them good candidates for short-to-medium range civil transport. However, to be successfully integrated into the civilian community, the tilt rotor must be perceived as a quiet, safe, and economical mode of transportation that does not harm the environment. In particular, noise impact has been identified as a possible barrier to the civil tilt rotor. Along with rotor conversion-mode flight, and blade-vortex interaction noise during descent, hover mode is a noise problem for tilt rotor operations. In the present research, tilt rotor hover aeroacoustics have been studied analytically, experimentally, and computationally. Various papers on the subject were published as noted in the list of publications. More recently, experimental measurements were made on a 1/12.5 scale model of the XV-15 in hover and analyses of this data and extrapolations to full scale were also carried out. A dimensional analysis showed that the model was a good aeroacoustic approximation to the full-scale aircraft, and scale factors were derived to extrapolate the model measurements to the full-scale XV-15. The experimental measurements included helium bubble flow visualization, silk tuft flow visualization, 2-component hot wire anemometry, 7-hole pressure probe measurements, vorticity measurements, and outdoor far field acoustic measurements. The hot wire measurements were used to estimate the turbulence statistics of the flow field into the rotors, such as length scales, velocity scales, dissipation, and turbulence intermittency. Several different configurations of the model were tested: (1) standard configurations (single isolated rotor, two rotors without the aircraft, standard tilt rotor configuration); (2) flow control devices (the 'plate', the 'diagonal fences'); (3) basic configuration changes (increasing the rotor/rotor spacing, reducing the rotor plane/wing clearance. operating the rotors out of phase). Also, an approximation to Sikorsky's Variable Diameter Tilt Rotor (VDTR) configuration was tested, and some flow measurements were made on a semi-span configuration of the model. Acoustic predictions were made using LOWSON.M, a Mathematica code Mean aerodynamic models were developed based on hover performance predictions from HOVER.FOR. This hover prediction code used blade element theory for the aerodynamics, and Prandtl's Vortex theory to model the wake, along with empirical formulas for the effects of Reynolds number, Mach number, and stall. Aerodynamic models were developed from 7-hole pressure probe measurements of the mean velocity into the model rotors.

George, Albert R.↗
NASA NTRS1987

Method for the determination of the three-dimensional aerodynamic field of a rotor-stator combination to compressible flow

Using the lifting surface theory and the acceleration potential method for the flow field of an axial turbocompressor stage, a recursive and a direct method are presented that make use of the eigenfunction solutions of the isolated rotor and stator to solve for the rotor-stator interaction problem. The net pressure distribution on the rotor and stator blades is represented by modified Birnbaum series, whose coefficients are determined using a matrix procedure and satisfying the boundary conditions on the surface of the blades. The relation between the matrix operators of the recursive and the direct methods is also shown. Expressions have been given for the blade circulation, the axial and tangential forces on the blade, the rotor power required, and the induced upwash velocity of the stage.

Ramachandra, Sridhar M.↗
NASA NTRS1987

Method for the determination of the three dimensional aerodynamic field of a rotor-stator combination in compressible flow

Using the lifting surface theory and the acceleration potential method for the flow field of an axial turbocompressor stage, a recursive and a direct method are presented that make use of the eigenfunction solutions of the isolated rotor and stator to solve for the rotor-stator interaction problem. The net pressure distribution on the rotor and stator blades is represented by modified Birnbaum series, whose coefficients are determined using a matrix procedure and satisfying the boundary conditions on the surface of the blades. The relation between the matrix operators of the recursive and the direct methods is also shown. Expressions have been given for the blade circulation, the axial and tangential forces on the blade, the rotor power required, and the induced upwash velocity of the stage.

Ramachandra, Sridhar M.↗
NASA NTRS2018

Measurements to Understand the Flow Mechanisms Contributing to Tandem-Rotor Outwash

Downwash and outwash characteristics of a model-scale tandem-rotor system in the presence of the ground were analyzed by identifying and understanding the physical mechanisms contributing to the observed flow field behavior. A building block approach was followed in simplifying the problem, separating the effects of the fuselage, effects of one rotor on the other, etc. Flow field velocities were acquired in a vertical plane at four aircraft azimuths of a small-scale tandem rotor system using the particle image velocimetry (PIV) technique for radial distances up to 4 times the rotor diameter. Results were compared against full-scale CH-47D measurements. Excellent correlation was found between the small- and full-scale mean flow fields (after appropriate normalization using rotor and wall jet parameters). Following the scalability analysis, the effect of rotor height on the outwash was also studied. Close to the aircraft, an increase in rotor height above ground decreased the outwash velocity at all aircraft azimuths. However, farther away, the longitudinal and lateral axes of the aircraft showed increasing and decreasing outwash velocities, respectively, with increasing rotor height. Measurements also indicated the presence of large-scale (of the size of the rotor height) shear-layer vortical structures along the ground that could be the source of low-frequency (approximately 1 Hz) flow variation observed in the full-scale measurements. Flow visualization studies and PIV measurements were also made on jets of different sizes to complement the observations made on rotors wherever possible. Baseline rotor measurements were made out-of-ground effect to understand the nature of inflow distribution for realistic rotor configurations and their modified characteristics in the presence of ground. Lastly, a feasibility study on applying high-fidelity CFD simulations for outwash study was conducted using Helios to model an isolated rotor configuration IGE at full scale Reynolds number. The results were encouraging and demonstrated the practical challenges associated with predicting rotor outwash.

Measurements↗
NASA NTRS2015

Measurements to Understand the Flow Mechanisms Contributing to Tandem-Rotor Outwash

Downwash and outwash characteristics of a model-scale tandem-rotor system in the presence of the ground were analyzed by identifying and understanding the physical mechanisms contributing to the observed flow field behavior. A building block approach was followed in simplifying the problem, separating the effects of the fuselage, effects of one rotor on the other, etc. Flow field velocities were acquired in a vertical plane at four aircraft azimuths of a small-scale tandem rotor system using the particle image velocimetry (PIV) technique for radial distances up to 4 times the rotor diameter. Results were compared against full-scale CH-47D measurements. Excellent correlation was found between the small- and full-scale mean flow fields (after appropriate normalization using rotor and wall jet parameters). Following the scalability analysis, the effect of rotor height on the outwash was also studied. Close to the aircraft, an increase in rotor height above ground decreased the outwash velocity at all aircraft azimuths. However, farther away, the longitudinal and lateral axes of the aircraft showed increasing and decreasing outwash velocities, respectively, with increasing rotor height. Measurements also indicated the presence of large-scale (of the size of the rotor height) shear-layer vortical structures along the ground that could be the source of low-frequency (approximately 1 Hz) flow variation observed in the full-scale measurements. Flow visualization studies and PIV measurements were also made on jets of different sizes to complement the observations made on rotors wherever possible. Baseline rotor measurements were made out-of-ground effect to understand the nature of inflow distribution for realistic rotor configurations and their modified characteristics in the presence of ground. Lastly, a feasibility study on applying high-fidelity CFD simulations for outwash study was conducted using Helios to model an isolated rotor configuration IGE at full-scale Reynolds number. The results were encouraging and demonstrated the practical challenges associated with predicting rotor outwash.

Ramasamy, Manikandan↗