Search NASA⌕ Search

SEARCH · Search NASA

Results for “LABYRINTH”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Theory versus experiment for the rotordynamic coefficients of labyrinth gas seals. II - A comparison to experiment

An experimental test facility is used to measure the leakage and rotordynamic coefficients of teeth-on-rotor and teeth-on-stator labyrinth gas seals. The test results are presented along with the theoretically predicted values for the two seal configurations at three different radial clearances and shaft speeds to 16,000 cpm. The test results show that the theory accurately predicts the cross-coupled stiffness for both seal configurations and shows improvement in the prediction of the direct damping for the teeth-on-rotor seal. The theory fails to predict a decrease in the direct damping coefficient for an increase in the radial clearance for the teeth-on-stator seal.

Childs, D. W.↗
NASA NTRS1988

Design optimization and testing of a pump wear ring labyrinth seal

It has been demonstrated that design optimization of labyrinth seals using the present numerical model is quite beneficial. The results shown include important, but previously unknown effects on the leakage rate, especially that of step height. Further, complete details are given of a very effective seal designed using this technique for the SSME high pressure hydrogen turbopump. Measurements using turbine flow meters revealed that the optimized configuration gives 67 percent leakage reduction over the original design. These measurements also reveal important leakage effects of the axial straining of the stator, which begins during pump start-up.

Rhode, D. L.↗
NASA NTRS1988

3-D laser anemometer measurements in a labyrinth seal

The flow field inside a seven cavity labyrinth seal with a 0.00127 m clearance was measured using a 3-D laser Doppler anemometer system. Through the use of this system, the mean velocity vector and the entire Reynolds stress tensor distributions were measured for the first, third, fifth, and seventh cavities of the seal. There was one large recirculation region present in the cavity for the flow condition tested, Re = 28,000 and Ta = 7,000. The axial and radial mean velocities as well as all of the Reynolds stress term became cavity independent by the third cavity. The azimuthal mean velocity varied from cavity to cavity with its magnitude increasing as the flow progressed downstream.

Morrison, G. L.↗
NASA NTRS1989

Rotordynamic coefficients for labyrinth seals calculated by means of a finite difference technique

The compressible, turbulent, time dependent and three dimensional flow in a labyrinth seal can be described by the Navier-Stokes equations in conjunction with a turbulence model. Additionally, equations for mass and energy conservation and an equation of state are required. To solve these equations, a perturbation analysis is performed yielding zeroth order equations for centric shaft position and first order equations describing the flow field for small motions around the seal center. For numerical solution a finite difference method is applied to the zeroth and first order equations resulting in leakage and dynamic seal coefficients respectively.

Nordmann, R.↗
NASA NTRS1991

Static and Dynamic Pressure Distributions in a Short Labyrinth Seal

As part of a study into turbine blade tip destabilizing forces, a seals test rig was built in which spin rate, circular whirl rate, direction and amplitude of inlet swirl angle, and eccentricity can all be controlled over wide ranges, and measurements can be made at gap Reynolds numbers up to about 2 x 10(exp 4). This facility is described and preliminary data is presented for a one cavity labyrinth seal with a flat, stator mounted land. The impact of different flow coefficients for the first and second knives on the rotordynamic coefficients was found. While this effect is dominant for the direct forces, it should also be incorporated into calculations of cross forces where it has an impact under many conditions.

Millsaps, K. T.↗
NASA NTRS1991

Evaluation of Rotordynamic Coefficients of Look-through Labyrinths by Means of a Three Volume Bulk Flow Model

To describe the compressible, turbulent flow in a labyrinth seal, a three volume bulk flow model is presented. The conservation equations for mass, momentum, and energy are established in every control volume. A perturbation analysis is performed, yielding zeroth order equations for centric rotor position and first order equations describing the flow field for small rotor motions around the seal center. The equations are integrated numerically. From perturbation pressure, the forces on the shaft and the dynamic coefficients are calculated.

Nordmann, R.↗
NASA NTRS1994

Rotordynamic forces in labyrinth seals: Theory and experiment

A theoretical and experimental investigation of the aerodynamic forces generated by a single gland labyrinth seal executing a simultaneous spinning/whirling motion has been conducted. A lumped parameter model for a single gland seal with coupling to an upstream cavity with leakage is developed along with an appropriate solution technique. From this theory, it is shown that the presence of the upstream cavity can, in some cases, augment the cross-stiffness and direct damping by a factor of four. The parameters that govern the coupling are presented along with predictions on their influence. A simple uncoupled model is used to identify the mechanisms responsible for cross force generation. This reduced system is nondimensionalized and the physical significance of the reduced parameters is discussed. Closed form algebraic formulas are given for some simple limiting cases. It is also shown that the total cross-force predicted by the uncoupled model can be represented as the sum of an ideal component due to an inviscid flow with entry swirl and a viscous part due to the change in swirl created by friction inside the gland. The frequency dependent ideal part is solely responsible for the rotordynamic direct damping. The facility designed and built to measure these frequency dependent forces is described. Experimental data confirm the validity and usefulness of this ideal/viscous decomposition. A method for calculating the damping coefficients based on the force decomposition using only the static measurements is presented. Experimental results supporting the predicted cross force augmentation due to the effect of upstream coupling are presented.

Millsaps, Knox T.↗
NASA NTRS1994

Calculation and measurement of the influence of flow parameters on rotordynamic coefficients in labyrinth seals

First experimental investigations performed on a new test rig are presented. For a staggered labyrinth seal with fourteen cavities the stiffness coefficient and the leakage flow are measured. The experimental results are compared to calculated results which are obtained by a one-volume bulk-flow theory. A perturbation analysis is made for seven terms. It is found out that the friction factors have great impact on the dynamic coefficients. They are obtained by turbulent flow computation by a finite-volume model with the Reynolds equations used as basic equations.

Kwanka, K.↗
NASA NTRS1997

Upstream Swirl Effects on the Flow Inside a Labyrinth Seal

The flow field inside a seven cavity tooth on rotor labyrinth seal was measured using a 3D laser Doppler anemometer system. The seal was operated at a Reynolds number of 24,000 and a Taylor number of 6,600 using water as the working fluid. Swirl vanes were placed upstream of the seal to produce positive, negative, and no preswirl. It was found that the axial and radial velocities were minimally effected. The tangential velocity, both in the clearance region and the seal cavities on the rotor, were greatly altered by the preswirl. By applying negative preswirl, the tangential velocity was suppressed, even in the seventh cavity. The turbulence levels decreased as the preswirl varied from negative to positive.

Morrison, Gerald L.↗
NASA NTRS2006

Mapping of Technological Opportunities-Labyrinth Seal Example

All technological systems evolve based on evolutionary sequences that have repeated throughout history and can be abstracted from the history of technology and patents. These evolutionary sequences represent objective patterns and provide considerable insights that can be used to proactively model future seal concepts. This presentation provides an overview of how to map seal technology into the future using a labyrinth seal example. The mapping process delivers functional descriptions of sequential changes in market/consumer demand, from today s current paradigm to the next major paradigm shift. The future paradigm is developed according to a simple formula: the future paradigm is free of all flaws associated with the current paradigm; it is as far into the future as we can see. Although revolutionary, the vision of the future paradigm is typically not immediately or completely realizable nor is it normally seen as practical. There are several reasons that prevent immediate and complete practical application, such as: 1) Some of the required technological or business resources and knowledge not being available; 2) Availability of other technological or business resources are limited; and/or 3) Some necessary knowledge has not been completely developed. These factors tend to drive the Total Cost of Ownership or Utilization out of an acceptable range and revealing the reasons for the high Total Cost of Ownership or Utilization which provides a clear understanding of research opportunities essential for future developments and defines the current limits of the immediately achievable improvements. The typical roots of high Total Cost of Ownership or Utilization lie in the limited availability or even the absence of essential resources and knowledge necessary for its realization. In order to overcome this obstacle, step-by-step modification of the current paradigm is pursued to evolve from the current situation toward the ideal future, i.e., evolution rather than revolution. A key point is that evolutionary stages are mapped to show step-by-step evolution from the current paradigm to the next major paradigm.

Clarke, Dana W., Sr.↗
NASA NTRS2010

Damping device for a stationary labyrinth seal

A stationary labyrinth seal system includes a seal housing having an annular cavity, a plurality of damping devices, and a retaining ring. The damping devices are positioned within the annular cavity and are maintained within the annular cavity by the retaining ring.

El-Aini, Yehia M.↗
NASA NTRS1977

Further investigation of the spontaneous and evoked activity of the primary neurons of statoreceptors (and other receptors) of the labyrinth of the bullfrog before, during and after an extended period of weightlessness, including alternative intervals of artificial gravity

Vestibular neuron activity was examined by studying nerve stimulation and evoked response. A cooling element, applied to the nerve consisted of a silver hook through which a coolant fluid flowed. Temperature changes were recorded via microtermistors on an eight channel brush recorder, together with response. Diffusion of the cooling effect was measured, recovery time was assessed, and the nerve was then studied hystologically and ultrastructurally. Problems in frog preparation were discussed along with problems in maintaining healthy specimens and bacteria controlled aquaria.

Source record↗
NASA NTRS1988

Numerical and experimental evaluation of a new low-leakage labyrinth seal

The effectiveness of a recently developed leakage model for evaluating new design features of most seals is demonstrated. A preliminary assessment of the present stator groove feature shows that it gives approximately a 20 percent leakage reduction with no shaft speed effects. Also, detailed distributions of predicted streamlines, axial velocity, relative pressure and turbulence energy enhance one's physical insight. In addition, the interesting measured effect of axial position of the rotor/stator pair on leakage rate and stator wall axial pressure distribution is examined.

Rhode, D. L.↗
NASA NTRS1987

Design improvement of a pump wear ring labyrinth seal

The investigation was successful in obtaining two improved designs for the impeller wear ring seal of the liquid hydrogen turbopump of interest. A finite difference computer code was extensively used in a parametric computational study in determining a cavity configuration with high flow resistance due to turbulence dissipation. These two designs, along with that currently used, were fabricated and tested. The improved designs were denoted Type O and Type S. The measurements showed that Type O and Type S given 67 and 30 percent reduction in leakage over the current design, respectively. It was found that the number of cavities, the step height and the presence of a small stator groove are quite important design features. Also, the tooth thickness is of some significance. Finally, the tooth height and an additional large cavity cut out from the stator (upstream of the step) are of negligible importance.

Rhode, David L.↗