Search NASA⌕ Search

SEARCH · Search NASA

Results for “LAGRANGE EQUATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Aeroelastic Studies of a Rectangular Wing with a Hole: Correlation of Theory and Experiment

Two rectangular wing models with a hole have been designed and tested in the Duke University wind tunnel to better understand the effects of damage. A rectangular hole is used to simulate damage. The wing with a hole is modeled structurally as a thin elastic plate using the finite element method. The unsteady aerodynamics of the plate-like wing with a hole is modeled using the doublet lattice method. The aeroelastic equations of motion are derived using Lagrange's equation. The flutter boundary is found using the V-g method. The hole's location effects the wing's mass, stiffness, aerodynamics and therefore the aeroelastic behavior. Linear theoretical models were shown to be capable of predicting the critical flutter velocity and frequency as verified by wind tunnel tests.

Conyers, Howard J.↗

Modeling the Benchmark Active Control Technology Wind-Tunnel Model for Application to Flutter Suppression

This paper describes the formulation of a model of the dynamic behavior of the Benchmark Active Controls Technology (BACT) wind-tunnel model for application to design and analysis of flutter suppression controllers. The model is formed by combining the equations of motion for the BACT wind-tunnel model with actuator models and a model of wind-tunnel turbulence. The primary focus of this paper is the development of the equations of motion from first principles using Lagrange's equations and the principle of virtual work. A numerical form of the model is generated using values for parameters obtained from both experiment and analysis. A unique aspect of the BACT wind-tunnel model is that it has upper- and lower-surface spoilers for active control. Comparisons with experimental frequency responses and other data show excellent agreement and suggest that simple coefficient-based aerodynamics are sufficient to accurately characterize the aeroelastic response of the BACT wind-tunnel model. The equations of motion developed herein have been used to assist the design and analysis of a number of flutter suppression controllers that have been successfully implemented.

Waszak, Martin R.↗

Modeling the Benchmark Active Control Technology Wind-Tunnel Model for Active Control Design Applications

This report describes the formulation of a model of the dynamic behavior of the Benchmark Active Controls Technology (BACT) wind tunnel model for active control design and analysis applications. The model is formed by combining the equations of motion for the BACT wind tunnel model with actuator models and a model of wind tunnel turbulence. The primary focus of this report is the development of the equations of motion from first principles by using Lagrange's equations and the principle of virtual work. A numerical form of the model is generated by making use of parameters obtained from both experiment and analysis. Comparisons between experimental and analytical data obtained from the numerical model show excellent agreement and suggest that simple coefficient-based aerodynamics are sufficient to accurately characterize the aeroelastic response of the BACT wind tunnel model. The equations of motion developed herein have been used to aid in the design and analysis of a number of flutter suppression controllers that have been successfully implemented.

Waszak, Martin R.↗

Analysis of preflutter and postflutter characteristics with motion-matched aerodynamic forces

The development of the equations of dynamic equilibrium for a lifting surface from Lagrange's equation is reviewed and restated for general exponential growing and decaying oscillatory motion. Aerodynamic forces for this motion are obtained from the three-dimensional supersonic kernel function that is newly generalized to complex reduced frequencies. Illustrative calculations were made for two flutter models at supersonic Mach numbers. Preflutter and postflutter motion isodecrement curves were obtained. This type of analysis can be used to predict preflutter behavior during flutter testing and to predict postflutter behavior for use in the design of flutter suppression systems.

Cunningham, H. J.↗

Dynamics of the AMCD ring

The derivation of the force-free equations of motion of a spinning flexible ring via Lagrange's equations is presented. Closed-form expressions for the natural frequencies are obtained for the most general motion of the ring. Numerical results for rings of different radii and spin rates are presented.

Oz, H.↗

A combined algorithm for minimum time slewing of flexible spacecraft

The use of Pontryagin's Maximum Principle for the large-angle slewing of large flexible structures usually results in the so-called two-point boundary-value problem (TPBVP), in which many requirements (e.g., minimum time, small flexible amplitude, and limited control powers, etc.) must be satisfied simultaneously. The successful solution of this problem depends largely on the use of an efficient numerical computational algorithm. There are many candidate algorithms available for his problem (e.g., quasilinearization, gradient, and shooting, etc.). In this paper, a proposed algorithm, which combines the quasilinearization method with a time shortening technique and a shooting method, is applied to the minimum-time, three-dimensional, and large-angle maneuver of flexible spacecraft, particularly the orbiting Spacecraft Control Laboratory Experiment (SCOLE) configuration. Theoretically, the nonlinear TPBVP can be solved only through the shooting method to find the 'exact' switching times for the bang-bang controls. However, computationally, a suitable guess for the missing initial costates is crucial because the convergence range of the unknown initial costates is usually narrow, especially for systems with high dimensions and when a multi-bang-bang control strategy is needed. On the other hand, the problems of near minimum time attitude maneuver of general rigid spacecraft and fast slewing of flexible spacecraft have been examined by the authors through a numerical approach based on the quasilinearization algorithm with a time shortening technique. Computational results have demonstrated its broad convergence range and insensitivity to initial costate choices. Consequently, a combined approach is naturally suggested here to solve the minimum time slewing problem. That is, in the computational process, the quasilinearization method is used first to obtain a near minimum time solution. Then, the acquired converged initial costates from the quasilinearization approach are transformed (tailored) to and used as the initial costate guess for starting the shooting method. Finally, the shooting method takes over the remaining calculations until the minimum-time solution converges. The nonlinear equations of motion of the SCOLE are formulated by using Lagrange's equations, with the mast modeled as a continuous beam subject to three-dimensional deformations. The numerical results will be presented and some related computational issues will also be discussed.

Bainum, P. M.↗

Dynamic modeling and control of multibody mechanical systems which are structurally flexible

This paper concerns the dynamic modeling and control of multibody, open-chained, structurally flexible, mechanical systems where the bodies are connected by revolute joints. The equations of motion are formulated based on a matrix form of Lagrange's equations for inertial quasi-coordinates. Each body is treated as a substructure of the system. For the purposes of simulation and control, the equations of motion are separated into two sets of equations using a perturbation approach: one to describe large rigid-body motions of the articulated system and the other to describe small linear motions of the bodies about the large motions. A biologically natural control strategy is used for vibration suppression and tracking the prescribed motion.

Quinn, R. D.↗

Aeroelastic Analysis of a Trimmed Generic Hypersonic Vehicle

The aeroelastic equations of motion governing a hypersonic vehicle in free flight are derived. The equations of motion for a translating and rotating flexible body using Lagrange's equations in terms of quasi-coordinates are presented. These equations are simplified for the case of a vehicle with pitch and plunge rigid body degrees of freedom and small elastic displacements. The displacements are approximated by a truncated series of the unrestrained mode shapes, which are obtained using equivalent plate theory. Subsequently, the nonlinear equations of motion are linearized about the trim state, which is obtained using a rigid body trim model and steady hypersonic aerodynamics. The appropriate flutter derivatives are calculated from piston theory. Results describing mode shapes, trim behavior, and aeroelastic stability of a generic hypersonic vehicle are presented.

Nydick, I.↗

On the flight dynamics of aeroelastic vehicles

The nonlinear equations of motion for an elasic airplane are developed from first principles. Lagrange's Equation and the Principle of Virtual Work are used to generate the equations of motion and strip theory is then employed to obtain closed form integral expressions for the generalized forces. The inertial coupling is minimized by appropriate choice of the body reference axes and by making use of free vibration modes of the body. In addition, particular attention is paid to the simplifying assumptions used during the development of the equations of motion. A unique aspect of this modeling process is that since the generalized aerodynamic forces are determined from closed form, analytic expressions, this method can be used to gain insight into the effects of parameter variations not easily obtained from numerical models. A numerical example is also presented in which the modeling method is applied to a representative elastic aircraft. The model is used to address the effects of aerodynamic coupling which occurs between the rigid body degrees of freedom and the elastic degrees of freedom. Finally, model simplification is addressed and two methods are evaluated. The resulting frequency responses are compared.

Schmidt, D. K.↗

Dynamic modeling of multi-jointed mechanical systems for space applications

The dynamic formulation, modeling and motion simulation of multijointed open-chained mechanical systems as applied to space-based robotic systems are presented. Equations of motion are formulated in a unique manner based on a form of Lagrange's equations for quasi-coordinates (Boltzmann-Hamel equations). In order that kinematic joint constraints can be satisfied for the situation where some joints have less than three degrees of freedom, the equations are transformed into forms in terms of relative angular velocities and Euler angles. Rigid multibody examples are presented which show that the method can provide a dynamic model of systems of varying complexity.

Quinn, R. D.↗

Rocket/launcher structural dynamics

The equations of motion describing the interactions between a rocket and a launcher were derived using Lagrange's Equation. A rocket launching was simulated. The motions of both the rocket and the launcher can be considered in detail. The model contains flexible elements and rigid elements. The rigid elements (masses) were judiciously utilized to simplify the derivation of the equations. The advantages of simultaneous shoe release were illustrated. Also, the loading history of the interstage structure of a boosted configuration was determined. The equations shown in this analysis could be used as a design tool during the modification of old launchers and the design of new launchers.

Ferragut, N. J.↗

Variations in the modal characteristics of a telescopically deploying beam

The equations of motion for a two-segment deploying telescopic beam are derived through application of Lagrange's equation. The outer tube of the beam is fixed at one end and the inner tube slides freely relative to the fixed segment. The resulting nonlinear, non-autonomous set of equations is linearized and simplified to the standard Euler-Bernoulli partial differential equations for an elastic beam by freezing the deployment process at various stages of deployment, and examining the small amplitude and natural modes of vibration of the resulting configuration. Application of the natural boundary conditions and compatibility of motion relations for the two segments in their common region of overlap leads to a transcendental characteristic equation in the frequency parameter Beta(L). Numerical solution of the equation for the characteristic roots determines the modal frequencies, and the corresponding mode shapes are obtained from the general solution of the Euler-Bernoulli equation tailored to the natural boundary conditions. Sample results of modal frequencies and shapes are presented for various stages of deployment and discussed. It is shown that for all intermediate stages of deployment (between 0 and 100 percent) the spectral distribution is drastically altered by the appearance of regions of very closely spaced modal frequencies. The sources of this modal agglomeration are explored.

Amos, Anthony K.↗

Users manual: Dynamics of two bodies connected by an elastic tether, six degrees of freedom forebody and five degrees of freedom decelerator

The equations of motion and a computer program for the dynamics of a six degree of freedom body joined to a five degree of freedom body by a quasilinear elastic tether are presented. The forebody is assumed to be a completely general rigid body with six degrees of freedom; the decelerator is also assumed to be rigid, but with only five degrees of freedom (symmetric about its longitudinal axis). The tether is represented by a spring and dashpot in parallel, where the spring constant is a function of tether elongation. Lagrange's equation is used to derive the equations of motion with the Lagrange multiplier technique used to express the constraint provided by the tether. A computer program is included which provides a time history of the dynamics of both bodies and the tension in the tether.

Doyle, G. R., Jr.↗

A recursive approach to the equations of motion for the maneuvering and control of flexible multi-body systems

Interest lies in a mathematical formulation capable of accommodating the problem of maneuvering a space structure consisting of a chain of articulated flexible substructures. Simultaneously, any perturbations from the 'rigid body' maneuvering and any elastic vibration must be suppressed. The equations of motion for flexible bodies undergoing rigid body motions and elastic vibrations can be obtained conveniently by means of Lagrange's equations in terms of quasi-coordinates. The advantage of this approach is that it yields equations in terms of body axes, which are the same axes that are used to express the control forces and torques. The equations of motion are nonlinear hybrid differential quations. The partial differential equations can be discretized (in space) by means of the finite element method or the classical Rayleigh-Ritz method. The result is a set of nonlinear ordinary differential equations of high order. The nonlinearity can be traced to the rigid body motions and the high order to the elastic vibration. Elastic motions tend to be small when compared with rigid body motions.

Kwak, Moon K.↗

Nonlinear dynamic response of wind turbine rotors

The nonlinear equations of motion for a rigid rotor restrained by three flexible springs representing the flapping, lagging and feathering motions are derived using Lagrange's equations for arbitrary angular rotations. These are reduced to a consistent set of nonlinear equations using nonlinear terms up to third order.

Chopra, I.↗

Dynamic analysis of satellites with deployable hinged appendages

The nonlinear equations of motion determining the planar dynamical behavior of an orbiting satellite deploying both one and two rigid appendages have been formulated using Lagrange's equations. The analysis accounts for large angle rotations, Coriolis effects, and the gravitational gradient, and the resulting coupled governing equations are integrated numerically. The analysis is applied to the Space Shuttle based deployment of rigid truss-like members, and results show that spacecraft inertia parameters, appendage mass and length, deployment velocity, and initial conditions all influence the system response. It is found that the resulting librational movement is related to the size of the deployment payload, and that gravitational forces lead to vehicle stabilization.

Oakes, Kevin F.↗