Search NASA⌕ Search

SEARCH · Search NASA

Results for “LATHES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Stress-induced α″ phase in a beta Ti–19Nb–1.5Mo–4Zr–8Sn alloy

Highlights: • Morphologies/distributions of α″ produced by stretching/rolling are similar. • Under small deformation, α″ martensite consists of parallel lamellar structures. • Under larger deformations, martensite has ladder-like pattern and parallel ellipsoids. • With the increase of deformation hardness decreases firstly and then increases. - Abstract: The morphological evolution of the stress-induced α″ martensite with increases in the stretching and rolling deformation degrees as well as the related orientation relationship were investigated in a β titanium alloy (Ti–19Nb–1.5Mo–4Zr–8Sn)·For a stretching deformation of 1%, the α″ martensite exhibited a packet morphology consisting of parallel lamellar structures. On the other hand, in the 2%-rolled sample, the α″ martensite exhibited a long lath-like distribution, which was accompanied by a few small pieces. With an increase in the deformation degree, the α″ martensite gradually exhibited a ladder-like structure consisting of long and short α″ laths or ellipsoids. The existence of these self-accommodating martensitic variants decreased the elastic energy. The parallel α″ laths present within a single packet were found to have the same orientation. The interface between the α″ and β phases was coherent, and their lattice constant relationships were identified as √2a{sub β}≈b{sub α″}≈c{sub α″} and a{sub β} ≈ a{sub α″}. Further, with the increase in the deformation degree, the hardness of the alloy first decreased and then increased; this was the case both the stretched as well as the rolled samples.

36 MATERIALS SCIENCE↗

Crystallization of plagioclase in mare basalts

A detailed study has been made of the morphology, zoning and major- and minor-element chemistry of plagioclase in mare basalt 12021 and for comparison, in several other mare basalts. Two types of plagioclase can be distinguished based on growth rate as expressed by the formation of hollow as opposed to lath-shaped crystals. The liquidus plagioclase is the most sodic part of the hollow crystals and is more sodic than the lath-shaped crystals. Hollow grains show oscillatory zoning, whereas the lath-shaped grains show normal zoning. The ratios FeO/(FeO + MgO) and K2O/(K2O + Na2O) increased in both types of plagioclase as they grew, and these ratios can be used as a guide to the crystallization history of the plagioclase. The FeO/(FeO + MgO) ratios are similar to those of coprecipitating pyroxene. The data presented here suggest the onset of plagioclase nucleation is primarily controlled by magma composition, and the point at which the magma becomes supersaturated with plagioclase.

Crawford, M. L.↗

Wax Reinforces Honeycomb During Machining

Method of machining on conventional metal lathe devised for precise cutting of axisymmetric contours on honeycomb cores made of composite (matrix/fiber) materials. Wax filling reinforces honeycomb walls against bending and tearing while honeycomb being contoured on lathe. Innovative method of machining on lathe involves preparation in which honeycomb is placed in appropriate fixture and the fixture is then filled with molten water-soluble wax. Number of different commercial waxes have been tried.

Towell, Timothy W.↗

Multiple Mechanisms of Uranium Immobilization by Cellulomonas sp. Strain ES6

Removal of hexavalent uranium (U(VI)) from aqueous solution was studied using a Gram-positive facultative anaerobe, Cellulomonas sp. strain ES6, under anaerobic, non-growth conditions in bicarbonate and PIPES buffers. Inorganic phosphate was released by cells during the experiments providing ligands for formation of insoluble U(VI) phosphates. Phosphate release was most probably the result of anaerobic hydrolysis of intracellular polyphosphates accumulated by ES6 during aerobic growth. Microbial reduction of U(VI) to U(IV) was also observed. However, the relative magnitudes of U(VI) removal by abiotic (phosphate-based) precipitation and microbial reduction depended on the buffer chemistry. In bicarbonate buffer, X-ray absorption fine structure (XAFS) spectroscopy showed that U in the solid phase was present primarily as a non-uraninite U(IV) phase, whereas in PIPES buffer, U precipitates consisted primarily of U(VI)-phosphate. In both bicarbonate and PIPES buffer, net release of cellular phosphate was measured to be lower than that observed in U-free controls suggesting simultaneous precipitation of U and PO3-4 . In PIPES, U(VI) phosphates formed a significant portion of U precipitates and mass balance estimates of U and P along with XAFS data corroborate this hypothesis. High-resolution transmission electron microscopy (HRTEM) and energy dispersive X-ray spectroscopy (EDS) of samples from PIPES treatments indeed showed both extracellular and intracellular accumulation of U solids with nanometer sized lath structures that contained U and P. In bicarbonate, however, more phosphate was removed than required to stoichiometrically balance the U(VI)/U(IV) fraction determined by XAFS, suggesting that U(IV) precipitated together with phosphate in this system. When anthraquinone-2,6-disulfonate (AQDS), a known electron shuttle, was added to the experimental reactors, the dominant removal mechanism in both buffers was reduction to a non-uraninite U(IV) phase. Uranium immobilization by abiotic precipitation or microbial reduction has been extensively reported; however, the present work suggests that strain ES6 can remove U(VI) from solution simultaneously through precipitation with phosphate ligands and microbial reduction, depending on the environmental conditions. Cellulomonadaceae are environmentally relevant subsurface bacteria and here, for the first time, the presence of multiple U immobilization mechanisms within one organism is reported using Cellulomonas sp. strain ES6.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Carbon Redistribution and Carbide Precipitation in a High-Strength Low-Carbon HSLA-115 Steel Studied on a Nanoscale by Atom Probe Tomography

HSLA-115 is a newly developed Cu-bearing high-strength low-carbon martensitic steel for use in Naval structural applications. This research provides, for the first time, a comprehensive compositional analysis of carbon redistribution and associated complex phase transformations in an isothermal aging study of HSLA-115 at 823 K (550 °C). Specifically, we characterize carbon segregation at lath boundaries, grain-refining niobium carbonitrides, cementite, and secondary hardening M2C carbides, in addition to copper precipitation, by 3D atom probe tomography (APT). Segregation of carbon (3 to 6 at. pct C) is observed at martensitic lath boundaries in the as-quenched and 0.12-hour aged microstructures. On further aging, carbon redistributes itself forming cementite and M2C carbides. Niobium carbonitride precipitates do not dissolve during the austenitizing treatment and are inherited in the as-quenched and aged microstructures; these are characterized along with cementite by synchrotron X-ray diffraction and APT. Sub-nanometer-sized M2C carbide precipitates are observed after the formation of Cu precipitates, co-located with the latter, indicating heterogeneous nucleation of M2C. The temporal evolution of the composition and morphology of M2C carbides at 823 K (550 °C) is described using APT; their precipitation kinetics is intertwined with Cu precipitates, affecting the bulk mechanical properties of HSLA-115. Phase compositions determined by APT are compared with computed compositions at thermodynamic equilibrium using ThermoCalc.

36 MATERIALS SCIENCE↗

Effect of Al-Si Coating on Weld Microstructure and Properties of 22MnB5 Steel Joints for Hot Stamping

22MnB5 hot stamping steels are gradually being used in tailor-welded blank applications. In this experiment, 1-mm-thick Al-Si coated and de-coated 22MnB5 steels were laser-welded and then hot-stamped. The chemical compositions, solidification process, microstructure and mechanical properties were investigated to reveal the effect of Al-Si coating and heat treatment. In the welded condition, the coated joints had an Al content of approximately 2.5 wt.% in the fusion zone and the de-coated joints had 0.5 wt.% Al. The aluminum promoted the δ-ferrite formation as the skeletal structure during solidification. In the high-aluminum weld, the microstructure consisted of martensite and long and band-like δ-ferrite. Meanwhile, the low-aluminum weld was full of lath martensite. After the hot stamping process, the δ-ferrite fraction increased from 10 to 24% in the coated joints and the lath martensite became finer in the de-coated joints. The tensile strengths of the coated joints or de-coated joints were similar to that before hot stamping, but the strength of the coated joints was reduced heavily after hot stamping compared to the de-coated joints and base material. The effect of δ-ferrite on the tensile properties became stronger when the fusion zone was soft and deformed first in the hot-stamped specimens. The coated weld showed a brittle fracture surface with many cleavage planes, and the de-coated weld showed a ductile fracture surface with many dimples in hot-stamped conditions.

36 MATERIALS SCIENCE↗

Simulation Kinetics of Austenitic Phase Transformation in Ti+Nb Stabilized IF and Microalloyed Steels

In the present study, the influence of cooling rates (low to ultrafast) on diffusion controlled and displacive transformation of Ti-Nb IF and microalloyed steels has been thoroughly investigated. Mechanisms of nucleation and formation of non-equiaxed ferrite morphologies (i.e., acicular ferrite and bainitic ferrite) have been analyzed in details. The continuous cooling transformation behavior has been studied in a thermomechanical simulator (Gleeble 3800) using the cooling rates of 1-150 °C/s. On the basis of the dilatometric analysis of each cooling rate, continuous cooling transformation (CCT) diagrams have been constructed for both the steels to correlate the microstructural features at each cooling rate in different critical zones. In the case of the IF steel, massive ferrite grains along with granular bainite structures have been developed at cooling rates > 120 °C/s. On the other hand, a mixture of lath bainitic and lath martensite structures has been formed at a cooling rate of ~ 80 °C/s in the microalloyed steel. A strong dependence of the cooling rates and C content on the microstructures and mechanical properties has been established. The steel samples that were fast cooled to a mixture of bainite ferrite and martensite showed a significant improvement of impact toughness and hardness (157 J, for IF steel and 174 J for microalloyed steel) as compared to that of the as-received specimens (133 J for IF steel and 116 J for microalloyed steel). Thus, it can be concluded that the hardness and impact toughness properties are correlated well with the microstructural constituents as indicated by the CCT diagram. Transformation mechanisms and kinetics of austenitic transformation to different phase morphologies at various cooling rates have been discussed in details to correlate microstructural evolution and mechanical properties.

36 MATERIALS SCIENCE↗

Recrystallization Behavior and Super-Elasticity of a Metastable β-Type Ti-21Nb-7Mo-4Sn Alloy During Cold Rolling and Annealing

Based on the d-electron alloy design theory, a new metastable β-type titanium alloy for biomedical applications, Ti-21Nb-7Mo-4Sn (wt.%) was designed in this article. This theory predicted this alloy was a metastable single β-type titanium alloy with low elastic modulus at room temperature, and the β-phase transition (β to α″) would be easy to occur during the cold rolling. The evolution of microstructure and mechanical properties of this alloy during cold rolling plus annealing were investigated by means of x-ray diffraction, optical microscope, transmission electron microscope and mechanical properties test. The results indicate that only β phase can be identified in this alloy before cold rolling, while a large amount of lath martensite (α″ phase) appears after cold rolling due to stress-induced martensitic transformation, which is in accordance with the prediction of the d-electron alloy design theory. The recrystallization nucleation occurs preferentially in the martensite lath region during the subsequent annealing process, and this region forms a large number of nano-crystals and microcrystals, showing that cold rolling plus annealing can become a new process for refining grains. Compared with casting and cold rolling samples, the annealing materials at 923 K for 10 min have excellent comprehensive mechanical properties with lower elastic modulus (58 GPa) and higher elastic recovery rate (35.39%).

36 MATERIALS SCIENCE↗

Microstructure and Tensile Properties of the Fe-32%Ni-4%Co Alloy During Cryorolling and Subsequent Annealing

The Fe-32%Ni-4%Co alloy was cryorolled to produce thickness reductions of 10, 40, 60 and 90%; then, the strips with a final thickness of 0.52 mm were annealed at 893, 923 and 943 K for different soaking times. The x-ray diffraction measurements indicated that both thermally induced α′-martensite (α′-M) and deformation-induced α′-M were present in the tested alloy. The thermally induced α′-M was mainly lath-shaped, while the morphology of the deformation-induced α′-M gradually changed from lath-shaped to irregular-shaped according to transmission electron microscopy observations. After the 90% reduction due to cryorolling, the total volume fraction of α′-M reached 75.6%, and the average ultimate tensile strength (UTS{sub av.}) was significantly improved from 430.3 to 1306.8 MPa. Upon subsequent annealing at 923 K for 5 min, the tested alloy mainly consisted of a large number of fine grains and a few coarse grains (CGs). In addition, several deformed structures were also observed. As the annealing time increased to 10 and 30 min, the fraction of CGs increased, and a bimodal grain size distribution was obtained, while the deformed structures were still present. The temperature of the reverse phase transformation of α′-M → γ was lower than the recrystallization temperature, which may be the main reason for the bimodal grain distribution. With this bimodal grain structure, the alloy exhibited a combination tensile strength of 543.3 MPa and an average elongation of 34.1%.

36 MATERIALS SCIENCE↗

Effect of Tempering Temperature on the Precipitation Behavior and Mechanical Properties of a Martensite Ferritic Steel

In this investigation, the precipitation of boron-containing M{sub 23}C{sub 6} in the CB2 steel during tempering was investigated. Scanning electron microscopy, energy-dispersive x-ray spectroscopy, transmission electron microscopy and differential scanning calorimetry were used to analyze the influence of temperature on the microstructure and properties of CB2-tempered martensite ferritic steel. The steel was normalized at 1100 °C for 2 h and then tempered at six different temperatures between 690 and 790 °C for 2 h. During air-cooling following austenitization, the precipitation of M{sub 3}C particles occurred in flakes forming with their diameter and thickness of 100 and 20 nm, respectively. The boron-containing M{sub 23}C{sub 6} was formed on the lath boundary after the dissolution of M{sub 3}C within the boundary. When the tempering temperature increased from 690 to 790 °C, the average diameter of boron-containing M{sub 23}C{sub 6} increased from 132 to 198 nm. Owing to the rapid growth of the precipitates, the phenomenon of lath widening as well as the recovery of microstructure would take place at high temperature. With an increase in the temperature, the tensile and yield strengths decreased gradually, while the plasticity increased and the boron-containing M{sub 23}C{sub 6} grew rapidly. Furthermore, when the tempering temperature exceeded 750 °C, the plasticity of CB2 steel was significantly improved.

36 MATERIALS SCIENCE↗

Effect of Cobalt on the Microstructure and Corrosion Behavior of Martensitic Age-Hardened Stainless Steel

To evaluate the influence of cobalt on the microstructure and pitting behavior of martensitic age-hardened stainless steel (MASS), the microstructures and electrochemical behaviors were characterized by optical microscopy, scanning electron microscopy, transmission electron microscopy, x-ray photoelectron spectroscopy, potentiodynamic curve, electrochemical impedance spectroscopy, and Mott–Schottky analysis. Results indicated that adding cobalt reduced the grain size of the original austenite, refined the lath martensite, inhibited the precipitation of Cu-rich phases, and increased the content of reversed austenite. Compared with the cobalt-free steel, the cobalt-containing steel has a higher pitting potential, lower corrosion current density, and higher pitting resistance. The primary components of the passive film grown on the cobalt-free steel included (Cr, Fe) oxides, such as Cr{sub 2}O{sub 3}, Cr(OH){sub 3}, FeOOH, and Fe{sub 2}O{sub 3}. The cobalt-containing steel included the aforementioned components as well as Co, which was attributed to the formation of the passive film in the forms of CoFe{sub 2}O{sub 4}, Co(OH){sub 2}, and CoO. In addition, the synergy of the refined lath martensite and the precipitation of the Cu-rich phase induced an increase in corrosion resistance in MASS containing cobalt.

36 MATERIALS SCIENCE↗

Microstructural Evolution and Toughness of the Various HAZs in 1300-MPa-Grade Ultrahigh-Strength Structural Steel

The effect of heat input on the microstructure and toughness of simulated subregions was investigated by welding thermal simulations and Charpy impact tests. The results indicate that the microstructures of the simulated coarse and fine grain heat affected zone (CGHAZ and FGHAZ) gradually changed from lath martensite to a mixture of lath martensite/lath bainite and finally to granular bainite with the increase in heat input. The microstructure of the simulated intercritical heat affected zone (ICHAZ) was mainly composed of granular bainite and blocky martensite regardless of heat input. When the heat input increased, the toughness of the simulated CGHAZ and ICHAZ continuously decreased. Nevertheless, the simulated FGHAZ still displayed good toughness (53.16 J) due to its fine structure. The occurrence of martensite-austenite (M-A) constituents was the main reason for the decrease in crack initiation energy of the simulated CGHAZ and ICHAZ at high values of heat input, and the toughness deteriorated as the size of M-A constituents increased. It should be noted that high-misorientation packet and block boundaries can effectively deviate or arrest the propagation of microcracks. When the heat input was in the approximate range of 8.63-14.95 kJ cm{sup −1}, all of the simulated subregions exhibited good toughness.

36 MATERIALS SCIENCE↗

Alpha – omega and omega – alpha phase transformations in zirconium under hydrostatic pressure: A 3D mesoscale study

Here, a three dimensional (3D) elastoplastic phase-field model is developed for modeling the hydrostatic pressure-induced alpha – omega phase transformation and the reverse phase transformation, i.e. omega – alpha, in zirconium (Zr). Plastic deformation and strain hardening of the material are also considered in the model. The microstructure evolution during both phase transformations is studied. The transformation start pressures at different temperatures are predicted and are plotted as a phase diagram. The effect of phase transformations on the mechanical properties of the material is also studied. The input data corresponding to pure Zr are acquired from experimental studies as well as by using the CALPHAD method. Our simulations show that three different omega variants form as laths. On release of pressure, reverse phase transformation initiates at lath boundaries. We observe that both phase transformations are martensitic in nature and also occur at the same pressure, i.e. little hysteresis. The transformation start pressures and the kinetics of the transformation predicted by our model are in good agreement with experimental results.

36 MATERIALS SCIENCE↗

Modeling the role of local crystallographic correlations in microstructures of Ti-6Al-4V using a correlated structure visco-plastic self-consistent polycrystal plasticity formulation

This paper presents a multi-level crystal plasticity-based simulation framework for modeling mechanical response and microstructure evolution of Ti-6Al-4V with α-lath/lamellar microstructures. Here, the model is a correlated structure visco-plastic self-consistent (CS-VPSC) formulation linking three scales: a single crystals micro-scale, a lath/lamellar colony meso-scale, and a lath/lamellar aggregate macro-scale. A selected hardening law for the evolution of critical resolved shear stress per slip system used in CS-VPSC is phenomenological. However, it adjusts the resistances of basal and prismatic slip systems based on the geometry of slip transfer between adjacent lamellae. Consistent with experimental evidences, the resolved shear stress on the pyramidal slip planes is dependent not only on the stress in the direction of slip but also on the two orthogonal shear stress components and the three normal stress components (non-Schmid effects). Electron backscatter diffraction (EBSD) data in conjunction with a procedure relying on α→β phase transformation is used to construct paired variants of α-laths/lamellae satisfying their local crystallographic correlations. The procedure fits volume fractions of individual laths/lamellae with the experimental EBSD data and selects a distribution of habit planes between adjacent variants with respect to the loading direction. The simulation framework is applied to interpret the deformation behavior in tension and compression along two sample directions of Ti-6Al-4V fabricated via laser powder bed fusion. Moreover, the model is used to simulate texture evolution during rolling of the material to large strains. It is demonstrated that the model is capable of predicting plastic anisotropy/asymmetry and the concomitant texture evolution. While the model reveals a significant effect of habit plane inclination with respect to the loading direction on yield stress, the comparison of the data and model predictions shows that a random distribution of habit planes fits the flow response. It is further inferred that the tension-compression asymmetry arises from the non-Schmid effects.

36 MATERIALS SCIENCE↗

Cryo-quenched Fe–Ni–Cr alloy decorative steel single crystals II: Alloy phases, structure, hardness, tensile, tribological, magnetic and electronic properties

We have previously reported (Boatner et al., J. Alloys Compd. 691 (2017) 666–671) on the discovery, formation, processing, and application of a new decorative ternary steel alloy and on its use in a wide range of practical applications including: custom and commercial knives, art objects, jewelry, electronics, and furniture. This decorative property results when polished single crystals of the 70 wt%Fe-15 wt%Ni-15 wt% Cr austenitic alloy are cryo-quenched into the martensitic phase resulting in the formation of a three-dimensional raised pattern of mixed austenitic/martensitic laths. These laths propagate across large dimensions of the material due to the absence of grain boundaries in the single crystal. The macroscopic optically reflective 3-D decorative pattern reproduces the structural symmetry inherent in the single-crystal orientation. This pattern results solely from the metallurgical phase properties of the ternary alloy and is completely distinct from the properties of Damascus steels or more modern so-called pattern-welded steels. Here we use X-ray diffraction, nanoindentation, hardness measurements/scratch testing, tribological measurements, and alloy resistivity and magnetization methods to obtain a more fundamental and comprehensive study of the effects of the austenitic/martensitic phase transition on the structural and physical properties of the 70 wt%Fe-15 wt%Ni-15 wt% Cr alloy. These results reveal new insight into irreversible phenomena that are associated with the inhibited phase transition on heating of the two-phase, mixed austenitic/martensitic structure that is formed subsequent to cryo-quenching the alloy crystal to 77 K.

36 MATERIALS SCIENCE↗

Transmission electron microscopy characterization of the fuel-cladding chemical interactions in HT9 cladded U-10Zr fuel

Fuel cladding chemical interaction (FCCI) is a key phenomenon needs to be better understood to establish the design basis for U-10Zr metallic fuel performance. Characterizing the microstructure and chemical composition of FCCI at micron and sub-micron scale is critically important toward a more mechanistic understanding of FCCI phenomenon and its potential effects on cladding integrity and metallic fuel performance. This paper, by using transmission electron microscopy, investigated the FCCI region in HT9 cladded U-10Zr fuel irradiated to 5.7% FIMA burnup at a peak inner cladding temperature of 615 °C in Fast Flux Test Facility (FFTF). Four distinct layers are identified in the FCCI region. The migration of Fe into the fuel side leads to the formation of several U-Zr-Fe ternary phases, including ?-Fe0.5Zr0.32U0.18, e-Fe0.3Zr0.4U0.3, and ?-Fe0.06Zr0.23U0.71, mingled with UFe2, U6Fe, and U phase at various Fe penetration depth up to ~ 150 µm. On the cladding side, grain coarsening and significant lanthanides infiltration along grain boundaries are observed. Laves phase, (Fe,Cr)2(Mo,W), which typically does not exist in fresh HT9, is identified in a wide radial range in the cladding. The typical HT9 martensitic lath structure and pre-existing M23C6 precipitates disappear, partially or completely, depending on the radial distance from the fuel-cladding interface. Those microstructural and compositional changes could cause mechanical degradation in the HT9 cladding. The present characterization results will improve the understanding of FCCI phenomenon and facilitate the development of microstructure-informed FCCI modeling for metallic fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Effect of acicular ferrite formation on grain refinement in the coarse-grained region of heat-affected zone

The microstructure of acicular ferrite and its formation for the grain refinement of coarse-grained region of heat-affected zone of high strength low-alloy bainite steels were studied using three-dimensional reconstruction technique. Crystallographic grain size was analyzed by means of electron backscatter diffraction. It was revealed that the microstructure in the coarse-grained region of the heat-affected zone consisted of predominantly bainite packets and a small proportion of acicular ferrite. Acicular ferrite was of lath or plate-like rather than needle or rod-like morphology. Tempering of the coarse-grained region of heat-affected zone showed that the acicular ferrite was more stable than the bainite, indicating that the acicular ferrite was formed prior to bainite. The acicular ferrite laths or plates divided the prior austenite grains into smaller and separate regions, and confining the bainite transformed at lower temperatures in the smaller regions and hence leading to the grain refinement in the coarse-grained region of the heat-affected zone.

36 MATERIALS SCIENCE↗

The formation mechanisms of interlocked microstructures in low-carbon high-strength steel weld metals

Microstructural features and the formation mechanisms of interlocked microstructures of acicular ferrite in a low-carbon high-strength steel weld metal were investigated by means of computer-aided three-dimensional reconstruction technique and electron backscattered diffraction analysis. Multiple nucleation on inclusions, sympathetic nucleation or repeated nucleation, hard impingement, mutual intersection, and fixed orientation relationships of acicular ferrite grains were observed. They were all responsible for the formation of interlocked microstructures in the weld metal. During the process of isothermal transformation, the pre-formed acicular ferrite laths or plates partitioned austenite grains into many small and separate regions, and the growth of later formed acicular ferrite grains was confined in these small regions. Thus, the crystallographic grain size became smaller with the increasing holding time. Highlights: Black-Right-Pointing-Pointer Acicular ferrite is formed by multiple nucleation and sympathetic nucleation. Black-Right-Pointing-Pointer Hard impingement and intersection of ferrite grains occur at later stages. Black-Right-Pointing-Pointer The pre-formed ferrite laths partition austenite grains into smaller regions. Black-Right-Pointing-Pointer The growth of later formed ferrite grains is confined in the smaller regions.

36 MATERIALS SCIENCE↗