Search NASA⌕ Search

SEARCH · Search NASA

Results for “MAGNESIUM FLUORIDE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

72 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS2015

High-Reflectivity Multi-Layer Coatings for the CLASP Sounding Rocket Project

We are planning an international rocket experiment Chromospheric Lyman-Alpha Spectro-Polarimeter (CLASP) is (2015 planned) that Lyman alpha line (Ly alpha line) polarization spectroscopic observations from the sun. The purpose of this experiment, detected with high accuracy of the linear polarization of the Ly alpha lines to 0.1% by using a Hanle effect is to measure the magnetic field of the chromosphere-transition layer directly. For polarization photometric accuracy achieved that approximately 0.1% required for CLASP, it is necessary to realize the monitoring device with a high throughput. On the other hand, Ly alpha line (vacuum ultraviolet rays) have a sensitive characteristics that is absorbed by the material. We therefore set the optical system of the reflection system (transmission only the wavelength plate), each of the mirrors, subjected to high efficiency of the multilayer coating in accordance with the role. Primary mirror diameter of CLASP is about 30 cm, the amount of heat about 30,000 J is about 5 minutes of observation time is coming mainly in the visible light to the telescope. In addition, total flux of the sun visible light overwhelmingly large and about 200 000 times the Ly alpha line wavelength region. Therefore, in terms of thermal management and 0.1% of the photometric measurement accuracy achieved telescope, elimination of the visible light is essential. We therefore, has a high reflectivity (greater than 50%) in Ly alpha line, visible light is a multilayer coating be kept to a low reflectance (less than 5%) (cold mirror coating) was applied to the primary mirror. On the other hand, the efficiency of the polarization analyzer required chromospheric magnetic field measurement (the amount of light) Conventional (magnesium fluoride has long been known as a material for vacuum ultraviolet (MgF2) manufactured ellipsometer; Rs = 22%) about increased to 2.5 times were high efficiency reflective polarizing element analysis. This device, Bridou et al. (2011) is proposed "that is coated with a thin film of the substrate MgF2 and SiO2 fused silica." As a result of the measurement, Rs = 54.5%, to achieve a Rp = 0.3%, high efficiency, of course, capable of taking out only about spolarized light. Other reflective optical elements (the secondary mirror, the diffraction grating-collector mirror), subjected to high-reflection coating of Al + MgF2 (reflectance of about 80%), less than 5% in the entire optical system by these (CCD Science was achieved a high throughput as a device for a vacuum ultraviolet ray of the entire system less than 5% (CCD of QE is not included).

sounding rocket↗
NASA NTRS2016

Optical Evaluation of DMDs with UV-Grade FS, Sapphire, MgF2 Windows and Reflectance of Bare Devices

Digital Micro-mirror Devices (DMDs) have been identified as an alternative to microshutter arrays for space-based multi-object spectrometers (MOS). Specifically, the MOS at the heart of a proposed Galactic Evolution Spectroscopic Explorer (GESE) that uses the DMD as a reprogrammable slit mask. Unfortunately, the protective borosilicate windows limit the use of DMDs in the UV and IR regimes, where the glass has insufficient throughput. In this work, we present our efforts to replace standard DMD windows with custom windows made from UV-grade fused silica, Low Absorption Optical Sapphire (LAOS) and magnesium fluoride. We present reflectance measurements of the antireflection coated windows and a reflectance study of the DMDs active area (window removed). Furthermore, we investigated the long-term stability of the DMD reflectance and recoating device with fresh Al coatings.

Quijada, Manuel A.↗
NASA NTRS2015

Solar Lyman-Alpha Polarization Observation of the Chromosphere and Transition Region by the Sounding Rocket Experiment CLASP

We are planning an international rocket experiment Chromospheric Lyman-Alpha Spectro-Polarimeter (CLASP) is (2015 planned) that Lyman α line (Ly(alpha) line) polarization spectroscopic observations from the sun. The purpose of this experiment, detected with high accuracy of the linear polarization of the Ly(alpha) lines to 0.1% by using a Hanle effect is to measure the magnetic field of the chromosphere-transition layer directly. For polarization photometric accuracy achieved that approx. 0.1% required for CLASP, it is necessary to realize the monitoring device with a high throughput. On the other hand, Ly(alpha) line (vacuum ultraviolet rays) have a sensitive characteristics that is absorbed by the material. We therefore set the optical system of the reflection system (transmission only the wavelength plate), each of the mirrors, subjected to high efficiency of the multilayer coating in accordance with the role. Primary mirror diameter of CLASP is about 30 cm, the amount of heat about 30,000 J is about 5 minutes of observation time is coming mainly in the visible light to the telescope. In addition, total flux of the sun visible light overwhelmingly large and about 200 000 times the Ly(alpha) line wavelength region. Therefore, in terms of thermal management and 0.1% of the photometric measurement accuracy achieved telescope, elimination of the visible light is essential. We therefore, has a high reflectivity (> 50%) in Lyα line, visible light is a multilayer coating be kept to a low reflectance (<5%) (cold mirror coating) was applied to the primary mirror. On the other hand, the efficiency of the polarization analyzer required chromospheric magnetic field measurement (the amount of light) Conventional (magnesium fluoride has long been known as a material for vacuum ultraviolet (MgF2) manufactured ellipsometer; Rs = 22%) about increased to 2.5 times were high efficiency reflective polarizing element analysis. This device, Bridou et al. (2011) is proposed "that is coated with a thin film of the substrate MgF2 and SiO2 fused silica." As a result of the measurement, Rs = 54.5%, to achieve a Rp = 0.3%, high efficiency, of course, capable of taking out only about s-polarized light. Other reflective optical elements (the secondary mirror, the diffraction gratingcollector mirror), subjected to high-reflection coating of Al + MgF2 (reflectance of about 80%), less than 5% in the entire optical system by these (CCD Science was achieved a high throughput as a device for a vacuum ultraviolet ray of the entire system less than 5% (CCD of QE is not included).

Narukage, Noriyuki↗
NASA NTRS2017

Enhanced Aluminum Reflecting and Solar-Blind Filter Coatings for the Far-Ultraviolet

The advancement of far-ultraviolet (FUV) coatings is essential to meet the specified throughput requirements of the Large UV/Optical/IR (LUVOIR) Surveyor Observatory which will cover wavelengths down to the 100 nm range. The biggest constraint in the optical thin film coating design is attenuation in the Lyman-Alpha Ultraviolet range of 100-130 nm in which conventionally deposited thin film materials used in this spectral region (e.g. aluminum [Al] protected with Magnesium fluoride [MgF2]) often have high absorption and scatter properties degrading the throughput in an optical system. We investigate the use of optimally deposited aluminum and aluminum tri-fluoride (AlF3) materials for reflecting and solar blind band-pass filter coatings for use in the FUV. Optical characterization of the deposited designs has been performed using UV spectrometry. The optical thin film design and optimal deposition conditions to produce superior reflectance and transmittance using Al and AlF3 are presented.

optical thin films↗
NASA NTRSDate not supplied

Enhanced Far Ultra-Violet Optical Properties of Physical Vapor Deposited Aluminum Mirrors Through Fluorination

Astronomical instrumentation for measurements in the Far Ultra-Violet (FUV, 90-200 nm) typically use aluminum (Al) thin films due to their high reflectance over this wavelength range. However, the native aluminum oxide layer that forms on Al upon exposure to the atmosphere is strongly absorbing in this wavelength range, requiring that the films be protected with a dielectric that inhibits oxidation. Typically, magnesium fluoride (MgF 2 ) or lithium fluoride (LiF) coatings are used as protective layers, but each has shortcomings. For example, MgF 2 has an absorption cutoff at 115 nm reducing performance in a critical part of the FUV spectrum of observational interest. A viable option to access these lower wavelengths could be the use of the LiF overcoat as it has a lower absorption cutoff at 102.5 nm, but it is hygroscopic and thus susceptible to degradation in humid conditions. An approach to reduce the hygroscopic nature of LiF would be to implement a passivation process during the deposition of both Al+LiF coatings. Our team at GSFC has developed a new reactive Physical Vapor Deposition (rPVD) process that consists of a fluorination process with XeF 2 gas combined with our traditional PVD process. We have found that this new rPVD coating process offers a protected version of Al+LiF with a more environmentally stable and more transparent LiF layer, along with unprecedent reflectivity. The process starts with a bare optically smooth substrate that is coated with Al in an ultra-high vacuum (UHV) chamber by the conventional PVD process. Then, the bare Al mirror is immediately exposed to a reactive XeF 2 gas before and after the application of the flash PVD evaporated LiF layer. We have also been investigating the use of this rPVD coating process for potential efficiency enhancements of Si-based gratings. Since it is known that the XeF 2 vapor is a strong Si etchant, we are investigating if the native SiO 2 layer on Si is sufficient to protect the groove profile of e-beam-ruled Si gratings from degradation. We will report on the characterization of various Al+LiF witness mirror coatings (both on borosilicate and Si) performed under various deposition conditions using the XeF 2 passivation process. These tests include XPS to determine film stoichiometry and AFM/SEM to measure surface roughness and any etching on the Si substrate. We will also report on FUV reflectance and spectroscopic ellipsometry to characterize optical constants of these passivated films in the UV/Visible/NIR spectral ranges.

Engineering (General)↗
NASA NTRSDate not supplied

Enhanced Far Ultra-Violet Optical Properties of Physical Vapor Deposited Aluminum Mirrors Through Fluorination

Astronomical instrumentation for measurements in the Far Ultra-Violet (FUV, 90-200 nm) typically use aluminum (Al) thin films due to their high reflectance over this wavelength range. However, the native aluminum oxide layer that forms on Al upon exposure to the atmosphere is strongly absorbing in this wavelength range, requiring that the films be protected with a dielectric that inhibits oxidation. Typically, magnesium fluoride (MgF 2 ) or lithium fluoride (LiF) coatings are used as protective layers, but each has shortcomings. For example, MgF 2 has an absorption cutoff at 115 nm reducing performance in a critical part of the FUV spectrum of observational interest. A viable option to access these lower wavelengths could be the use of the LiF overcoat as it has a lower absorption cutoff at 102.5 nm, but it is hygroscopic and thus susceptible to degradation in humid conditions. An approach to reduce the hygroscopic nature of LiF would be to implement a passivation process during the deposition of both Al+LiF coatings. Our team at GSFC has developed a new reactive Physical Vapor Deposition (rPVD) process that consists of a fluorination process with XeF 2 gas combined with our traditional PVD process. We have found that this new rPVD coating process offers a protected version of Al+LiF with a more environmentally stable and more transparent LiF layer, along with unprecedent reflectivity. The process starts with a bare optically smooth substrate that is coated with Al in an ultra-high vacuum (UHV) chamber by the conventional PVD process. Then, the bare Al mirror is immediately exposed to a reactive XeF 2 gas before and after the application of the flash PVD evaporated LiF layer. We have also been investigating the use of this rPVD coating process for potential efficiency enhancements of Si-based gratings. Since it is known that the XeF 2 vapor is a strong Si etchant, we are investigating if the native SiO 2 layer on Si is sufficient to protect the groove profile of e-beam-ruled Si gratings from degradation. We will report on the characterization of various Al+LiF witness mirror coatings (both on borosilicate and Si) performed under various deposition conditions using the XeF 2 passivation process. These tests include XPS to determine film stoichiometry and AFM/SEM to measure surface roughness and any etching on the Si substrate. We will also report on FUV reflectance and spectroscopic ellipsometry to characterize optical constants of these passivated films in the UV/Visible/NIR spectral ranges.

Engineering (General)↗
NASA NTRSDate not supplied

Enhanced Far Ultra-Violet Optical Properties of Physical Vapor Deposited Aluminum Mirrors Through Fluorination

Astronomical instrumentation for measurements in the Far Ultra-Violet (FUV, 90-200 nm) typically use aluminum (Al) thin films due to their high reflectance over this wavelength range. However, the native aluminum oxide layer that forms on Al upon exposure to the atmosphere is strongly absorbing in this wavelength range, requiring that the films be protected with a dielectric that inhibits oxidation. Typically, magnesium fluoride (MgF 2 ) or lithium fluoride (LiF) coatings are used as protective layers, but each has shortcomings. For example, MgF 2 has an absorption cutoff at 115 nm reducing performance in a critical part of the FUV spectrum of observational interest. A viable option to access these lower wavelengths could be the use of the LiF overcoat as it has a lower absorption cutoff at 102.5 nm, but it is hygroscopic and thus susceptible to degradation in humid conditions. An approach to reduce the hygroscopic nature of LiF would be to implement a passivation process during the deposition of both Al+LiF coatings. Our team at GSFC has developed a new reactive Physical Vapor Deposition (rPVD) process that consists of a fluorination process with XeF 2 gas combined with our traditional PVD process. We have found that this new rPVD coating process offers a protected version of Al+LiF with a more environmentally stable and more transparent LiF layer, along with unprecedent reflectivity. The process starts with a bare optically smooth substrate that is coated with Al in an ultra-high vacuum (UHV) chamber by the conventional PVD process. Then, the bare Al mirror is immediately exposed to a reactive XeF 2 gas before and after the application of the flash PVD evaporated LiF layer. We have also been investigating the use of this rPVD coating process for potential efficiency enhancements of Si-based gratings. Since it is known that the XeF 2 vapor is a strong Si etchant, we are investigating if the native SiO 2 layer on Si is sufficient to protect the groove profile of e-beam-ruled Si gratings from degradation. We will report on the characterization of various Al+LiF witness mirror coatings (both on borosilicate and Si) performed under various deposition conditions using the XeF 2 passivation process. These tests include XPS to determine film stoichiometry and AFM/SEM to measure surface roughness and any etching on the Si substrate. We will also report on FUV reflectance and spectroscopic ellipsometry to characterize optical constants of these passivated films in the UV/Visible/NIR spectral ranges.

Engineering (General)↗
NASA NTRS1994

Millimeter and submillimeter rest frequencies for the MgF radical

The pure rotational spectrum of the MgF radical in its ground X(sup 2) Sigma(+) electronic state has been observed in the laboratory using millimeter/submillimeter direct absorption spectroscopy. Rotational transitions arising from the v = 0, 1, 2, and 3 vibrational modes of the main magnesium isotopic species, (24)MgF, have been recorded, as well as those arising from the v = 0 state of the Mg-25 and Mg-26 isotopomers. Rotational and fine-structure constants have been determined for these molecules, as well as hyperfine parameters for both the F-19 (I = 1/2) and Mg-25 (I = 5/2) nuclei. The rest frequencies presented here for MgF have an estimated accuracy of +/- 200 kHz, and will enable astronomical searches to be carried out for this fluoride radical. Magnesium fluoride may be present in the late-type carbon star IRC +10216, where AlF appears to be abundant.

Anderson, M. A.↗
NASA NTRS1974

Development of fine diameter mullite fiber

Results are presented of a program to develop and evaluate mullite fiber with a mean diameter under two microns. The two micron fiber is produced by a blowing process at room temperature from a low viscosity (10-25 poise) solution. The blown fiber was evaluated for dimensional stability in thermal cycling to 1371 C, and was equivalent to the 5 micron spun B and W mullite fiber. An additive study was conducted to evaluate substitutes for the boron. Three levels of chromium, lithium fluoride, and magnesium were added to the standard composition in place of boron and the fiber produced was evaluated for chemical and dimensional stability in thermal cycling to 1371 C. The magnesium was the most chemically stable, but the chrome additive imparted the best dimensional stability.

Long, W. G.↗
NASA NTRS1995

Effects of the LDEF orbital environment on the reflectance of optical mirror materials

Specimens of eight different optical mirror materials were flown in low earth orbit as part of the Long Duration Exposure Facility (LDEF) manifest to determine their ability to withstand exposure to the residual atomic oxygen and other environmental effects at those altitudes. Optical thin films of aluminum, gold, iridium, osmium, platinum, magnesium fluoride-overcoated aluminum and reactively deposited, silicon monoxide-protected aluminum, all of which were vacuum deposited on polished fused silica substrates, were included as part of Experiment S0010, Exposure of Spacecraft Coatings. Two specimens of polished, chemical vapor deposited (CVD) silicon carbide were installed in sites available in Experiment A0114, Interaction of Atomic Oxygen with Solid Surfaces at Orbital Altitudes, which included trays in two of the spacecraft bays, one on the leading edge and the other on the trailing edge. One of the silicon carbide samples was located in each of these trays. This paper will compare specular reflectance data from the preflight and postflight measurements made on each of these samples and attempt to explain the changes in light of the specific environments to which the experiments were exposed.

Herzig, Howard↗
NASA NTRS1992

Radiation monitoring container device (16-IML-1)

In this experiment, layers of radiation detectors and biological specimens, bacterial spores (Bacillus subtillis), shrimp eggs (Altemia salina), and maize seeds (Zea mays) are sandwiched together in the Radiation Monitoring Container. The detectors, sheets of plastic materials, record the nuclear track of cosmic radiation. The dosimeter package contains conventional detectors made of materials such as lithium fluoride or magnesium-silica-terbium. The thermoluminescent materials (TLD) will, when moderately heated, emit luminescent photons linearly depending upon the dose of radiation received. The experiment, enclosed in a box-like container, is mounted on the aft end cone of the Spacelab, the area where the shielding is somewhat less than other locations.

Nagaoka, S.↗
NASA NTRS2018

E-Beam Generated Plasma Etching for Developing High-Reflectance Mirrors for Far-Ultraviolet Astronomical Instrument Applications

Astronomical space telescopes to study astrophysical phenomena from the far-ultraviolet (FUV) to the near infrared (NIR) will require mirror coatings with high reflectance over this entire spectral region. While coatings for the optical and NIR part of the spectrum are fairly well developed with proven performance, the FUV presents significant challenges. The U.S. Naval Research Laboratory (NRL) has developed a processing system based on an electron beam-generated plasma that provides for controlled fluorination and/or etching of surfaces with near monolayer precision and minimal changes to surface morphology. In this paper, we report recent results of samples treated in the NRL Large Area Plasma Processing System (LAPPS) where restoration of the high intrinsic reflectance in the FUV spectral range have been observed of aluminum (Al) mirrors protected with a magnesium di-fluoride (MgF2) overcoat. This paper will also extend these studies to other Al mirrors protected with aluminum tri-fluoride (AlF3) in order to realize the high intrinsic reflectance Al down to FUV wavelengths (100−200 nm), while still maintaining the high reflectance in the optical and NIR spectral regions. Laboratory test data and optical diagnostic techniques used to verify surface scattering and durability of selected coatings will be presented. Finally, we will discuss the scalability of the LAPPS etching process in order to realize these high-reflectivity coatings on mirror segments as large as those proposed for the Large Ultraviolet, Optical, and Infrared (LUVOIR) astronomical telescope system (1+meter class).

LUVOIR↗
NASA NTRS1961

Development of Ceramic Fibers for Reinforcement in Composite Materials

Refinements of the vertical arc fiberizing apparatus resulted in its ability to fiberize very different refractory glasses having wide ranges of properties. Although the apparatus, was originally designed as a laboratory research tool for the evaluation of many compositions daily, up to one quarter pound of fibers of a single composition could be produced in an 8-hour day. Fibers up to six and a half feet long were produced with the apparatus. Studies were conducted of two methods of fiberizing refractory glasses requiring rapid freezing from the melt. The first method consisted of fiberizing droplets of molten glass passing through an annular nozzle. The second method consisted of reconstructing the annular nozzle in. the shape of a horseshoe to achieve a shorter delay in blasting a molten droplet from the tip of a rod. Both methods were judged feasible for producing fibers of glasses requiring rapid freezing. The first method would be more amenable to volume fiber production. Studies of induction heating for fiber formation did not lead to its designation as a very efficient heating method. Problems. remain to be solved, in the design of a suitable susceptor for a higher heating rate, in protecting the susceptor from oxidation with an inert gas, in contamination of the melt from a refractory crucible, and in the protective radiation shielding of the induction concentrator coil. It is not considered practical to continue studies of this heating method. In the course of this program 151 refractory glass compositions were evaluated for fiber, forming characteristics. Of the various types of materials studied, the following showed promise in producing acceptable refractory fibers: sIlica- spinel (magnesium aluminate), silica- spinel-zirconia, silica-zirconia, silica-zinc spinel, aluminum phosphate glasses, and fluoride glasses. Compositions which did not produce acceptable fibers were high zirconia materials, barium spinels, and calcium aluminates. Improvements in the. testing apparatus for single fiber tensile strength increased the precision. of tests conducted on nine fibers. The highest mean tensile strength, a value of 295,000 pounds per square inch, was obtained with R-141 fibers. Treatment of R-74 fibers with anhydrous Linde A-1100 silane finish improved its mean fiber tensile strength by 25 percent. The lapse of time after fiber formation had no measurable effect on tensile strength. A static heating test conducted with various high melting fibers indicated that Fiberfrax and R-108 underwent no significant changes in bulk volume or resiliency on exposure to 2750 degrees Fahrenheit (1510 degrees Centigrade) in an oxidizing atmosphere. For fiber-resin composition fabrication, ten fiber materials were selected on the bases of high fiber yield, fusion temperature, and type of composition. Fiberfrax, a commercial ceramic fiber, was included for comparison. A new, more effective method of removing pellets from blown fibers was developed. The de-pelletized fibers were treated with a silane finish and felted into ten-inch diameter felts prior to resin impregnation. Composites containing 30 percent by weight of CTL 91-LD phenolic resin were molded under high pressure from the impregnated felts and post-cured to achieve optimum properties. Flexural strength, flexural modules of elasticity, and punch shear strength tests were conducted on the composite specimens. The highest average flexural strength obtained was 19,958 pounds per square inch with the R-74-fiber-resin composite. This compares very favorably with the military specification of 13,000 pounds per square inch flexural strength for randomly oriented fiber reinforced composites. The highest punch shear strength (11,509 pounds per square inch) was obtained with the R-89 fiber-resin composite. The effects of anhydrous fiber finishes on composite strength were not clearly indicated. Plasma arc tests at a heat flux of 550 British Thermal Units per square foot per second on eight composite materials indicated ablation rates generally equivalent to Fiberglas-Micarta No. 259-2. The composite reinforced with R-99 fibers had an average ablation rate of 0.008 inch per second and appears quite promising on the basis of these tests. Preliminary studies for processing fibers into yarn and fabric were conducted with R-99 fibers. The use of certain organic gums aided in 2 fabricating by hand several relatively strong yarns and a crude fabric swatch. This indicated the practicality of developing techniques for processing these fibers into yarn and fabric without significant damage to the fibers.

Gates, L. E.↗
NASA NTRS1982

Venus - Chemical weathering of igneous rocks and buffering of atmospheric composition

Data from the Pioneer Venus radar mapper, combined with measurements of wind velocity and atmospheric composition, suggest that surface erosion on Venus varies with altitude. Calcium- and magnesium-rich weathering products are produced at high altitudes by gas-solid reactions with igneous minerals, then removed into the hotter lowlands by surface winds. These fine-grained weathering products may then rereact with the lower atmosphere and buffer the composition of the observed gases carbon dioxide, water vapor, sulfur dioxide, and hydrogen fluoride in some regions of the surface. This process is a plausible mechanism for the establishment in the lowlands of a calcium-rich mineral assemblage, which had previously been found necessary for the buffering of these species.

Nozette, S.↗
NASA NTRS2009

Production of Oxygen from Lunar Regolith by Molten Oxide Electrolysis

This paper describes the use of the molten oxide electrolysis (MOE) process for the extraction of oxygen for life support and propellant, and silicon and metallic elements for use in fabrication on the Moon. The Moon is rich in mineral resources, but it is almost devoid of chemical reducing agents, therefore, molten oxide electrolysis is ideal for extraction, since the electron is the only practical reducing agent. MOE has several advantages over other extraction methods. First, electrolytic processing offers uncommon versatility in its insensitivity to feedstock composition. Secondly, oxide melts boast the twin key attributes of highest solubilizing capacity for regolith and lowest volatility of any candidate electrolytes. The former is critical in ensuring high productivity since cell current is limited by reactant solubility, while the latter simplifies cell design by obviating the need for a gas-tight reactor to contain evaporation losses as would be the case with a gas or liquid phase fluoride reagent operating at such high temperatures. Alternatively, MOE requires no import of consumable reagents (e.g. fluorine and carbon) as other processes do, and does not rely on interfacing multiple processes to obtain refined products. Electrolytic processing has the advantage of selectivity of reaction in the presence of a multi-component feed. Products from lunar regolith can be extracted in sequence according to the stabilities of their oxides as expressed by the values of the free energy of oxide formation (e.g. chromium, manganese, Fe, Si, Ti, Al, magnesium, and calcium). Previous work has demonstrated the viability of producing Fe and oxygen from oxide mixtures similar in composition to lunar regolith by molten oxide electrolysis (electrowinning), also called magma electrolysis having shown electrolytic extraction of Si from regolith simulant. This paper describes recent advances in demonstrating the MOE process by a joint project with participation by NASA KSC and MSFC, and Ohio State University and MIT. Progress in measuring cell efficiency for oxygen production, development of non reacting electrodes, and cell feeding and withdrawal will be discussed.

Curreri, Peter A.↗
NASA NTRS1994

Formation and chemical reactivity of carbon fibers prepared by defluorination of graphite fluoride

Defluorination of graphite fluoride (CFX) by heating to temperatures of 250 to 450 C in chemically reactive environments was studied. This is a new and possibly inexpensive process to produce new carbon-based materials. For example, CF 0.68 fibers, made from P-100 carbon fibers, can be defluorinated in BrH2C-CH = CH-CH2Br (1,4-dibromo-2butene) heated to 370 C, and graphitized to produce fibers with an unusually high modulus and a graphite layer structure that is healed and cross-linked. Conversely, a sulfur-doped, visibly soft carbon fiber was produced by defluorinating CF 0.9 fibers, made from P-25, in sulfur (S) vapor at 370 C and then heating to 660 C in nitrogen (N2). Furthermore, defluorination of the CF 0.68 fibers in bromine (Br2) produced fragile, structurally damaged carbon fibers. Heating these fragile fibers to 1100 C in N2 caused further structural damage, whereas heating to 150 C in bromoform (CHBr3) and then to 1100 C in N2 healed the structural defects. The defluorination product of CFX, tentatively called activated graphite, has the composition and molecular structure of graphite, but is chemically more reactive. Activated graphite is a scavenger of manganese (Mn), and can be intercalated with magnesium (Mg). Also, it can easily collect large amounts of an alloy made from copper (Cu) and type 304 stainless steel to form a composite. Finally, there are indications that activated graphite can wet metals or ceramics, thereby forming stronger composites with them than the pristine carbon fibers can form.

Hung, Ching-Cheh↗