Search NASA⌕ Search

SEARCH · Search NASA

Results for “MATERIALS EROSION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Monitoring Potential Transport of Radioactive Contaminants in Shallow Ephemeral Channels: FY2019

Desert Research Institute (DRI) conducted a field assessment of the potential for contaminated soil to be transported from the Smoky Site Contamination Area (CA) because of storm runoff. This activity supported U.S. Department of Energy (DOE) Environmental Management Nevada Program (EM NV) efforts to establish post-closure monitoring plans for the Smoky Site Soils Corrective Action Unit (CAU) 550. The work was intended to confirm the likely mechanism of transport and determine the meteorological conditions that might cause the movement of contaminated soils, as well as determine the particle size fraction most closely associated with transported radionuclide-contaminated soils. These data will facilitate the design of the appropriate post-closure monitoring program. In 2011, DRI installed a meteorological monitoring station on the west side of the Smoky Site CA and a hydrologic (runoff) monitoring station within the CA, near the east side. The meteorological station collected air temperature, wind speed, wind direction, relative humidity, precipitation, solar radiation, barometric pressure, soil temperature, and soil water content data. The maximum, minimum, and average or total values (as appropriate) for each of these parameters were recorded for each 10-minute interval. The maximum, minimum, and average water depth in the flume installed at the hydrologic station were also recorded for each 10-minute interval. This report presents the data collected from these stations during fiscal year (FY) 2019. During the FY2019 reporting period, the warmest months were June, July, and August and the coldest were December and February. The highest monthly solar radiation (i.e., sunshine) values were recorded in June, July, and August, whereas December through February had the lowest solar radiation values. Monthly mean wind speeds were highest in the spring (April) and early summer (June). Winds were predominantly from the north, except in February, July, August, and September when winds were mostly from the west. The monthly average relative humidity ranged from 17 percent to approximately 60 percent. Humidity was lowest in the summer and highest in the winter. Monthly total precipitation ranged from 0.0 during August and September to 2.22 inches (in) (56.39 millimeters [mm]) in February. Total precipitation for FY2019 was 7.83 in (198.88 mm). During the reporting period, a single, nonzero, flow event was recorded at the flume. This occurred over two days between March 6 and 7, 2019, in response to 1.16 in (29.46 mm) of precipitation falling within 9.3 hours on March 6, 2019. This event produced a peak water depth of 0.39 in (0.99 centimeters [cm]) in the flume, and runoff was measured for approximately 23.5 hours. However, the maximum recorded flow depth was less than the limit for flow discharge and velocity that can be calculated for the six-inch (15 cm) throat of a Parshall flume. The runoff event produced insufficient flow velocities through the natural channel to cause local erosion and transport of bedload materials. No bedload samples were collected for radiological analysis. Observing meteorological and environmental conditions that lead to storm runoff will help identify the parameters and threshold conditions that should be incorporated into post-closure monitoring plans for this and similar Soils CAU sites. Routine monitoring of meteorological and hydrologic parameters at the Smoky Site CA has been discontinued at the request of EM NV, effective at the conclusion of FY2019. Environmental data acquisition was completed and the meteorological and runoff monitoring stations were removed from the Smoky Site on October 15, 2019.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Comprehensive new insights on the potential use of SiC as plasma-facing materials in future fusion reactors

Abstract The performance of silicon carbide as an alternative plasma facing material (PFM) was studied at various irradiation conditions relevant to ion energies and fluxes of a fusion reactor. This analysis involves detailed modeling of subsurface plasma/material interactions, sputtered particle transport above the surface and redeposition, and related changes in material composition and microstructure induced by steady-state and Edge Localized Mode ion fluxes. Transition of a crystalline SiC surface to semi-crystalline and amorphous phases was analyzed based on advanced modeling of DIII-D tokamak experiments where SiC was irradiated in single- and multiple- L-mode and H-mode discharges. This analysis shows that displacement damage, particle deposition/redeposition, and D accumulation on the SiC divertor surface can lead to significant microstructural changes that result in enhanced sputtering erosion in comparison with the original crystalline material. However, the resulting total net erosion rate for a full-coverage, advanced tokamak, SiC coated divertor may well be acceptably low. Moreover, the C sputtering yield from the evolved SiC surface can be seven times lower than from a pure graphite surface; this would imply significantly reduced tritium co-deposition rates in a D-T tokamak reactor, compared with a pure carbon surface. It was also determined that chemical sputtering of both C and Si should not result in any noticeable effect on the net erosion, for attached plasma regimes. Our results thus show encouraging results overall for use of SiC as a PFM in tokamaks.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Application of an Erosion Wear Model to Predict Wear of Hammer Milling Components

A workable analytical erosion model that relates critical hammermill process parameters (hammermill geometry and rotational speed) to critical material attributes of inorganic mineral species in feedstock (density, size, and aspect ratio) and substrate (hardness, toughness, and fatigue ductility) was applied to model wear (more specifically, change in the shape of hammers) in hammer milling operations. Results of the model were compared to experimental observations of the shape of hammers used in the INL Stage 1 Vermeer hammermill. Results showed good agreement between predicted and measured shape of the hammer, and that a quality-by-design (QbD) approach can be developed to predict component reliability based on scientific engineering principles in lieu of trial-and-error approaches.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Erosion and cathodic arc plasma of Nb–Al cathodes: composite versus intermetallic

Many properties of cathodic arcs from single-element cathodes show a correlation to the cohesive energy of the cathode material. For example, the burning voltage, the erosion rate, or, to a lesser extent, plasma properties like electron temperatures or average ion energy and charge states. For multi-element cathodes, various phases with different cohesive energies can initially be present in the cathode, or form due to arc exposure, complicating the evaluation of such correlations. To test the influence of morphology and phase composition of multi-element cathodes on cathodic arc properties, a Nb–Al cathode model system was used that includes: pure Nb and Al cathodes; intermetallic Nb 3 Al, Nb 2 Al and NbAl 3 cathodes; and three composite Nb–Al cathodes with atomic ratios corresponding to the stoichiometric ratios of the intermetallic phases. Pulsed cathodic arc plasmas from these cathodes were examined using a mass-per-charge and energy-per-charge analyzer, showing that charge-state-resolved ion energy distributions of plasmas from the intermetallic and corresponding composite cathodes are nearly identical. An examination of converted layers of eroded cathodes using x-ray diffraction and scanning electron microscopy indicates the formation of a surface layer with similar phase composition for intermetallic and their corresponding composite cathode types. The average arc voltages do not follow the trend of cohesive energies of Nb, Al and intermetallic Nb–Al phases, which have been calculated using density functional theory. Possible reasons for this effect are discussed based on the current knowledge of multi-element arc cathodes and their arc plasma available in literature.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of temperature on abrasion erosion in particle based concentrating solar powerplants

The use of solid particles as a heat transfer medium is being explored for concentrated solar power plants (CSP) to increase their efficiency by achieving operating temperature >700 °C. During operation, these hot particles are expected to move along the various components within the collector system, resulting in material degradation from a combination of high-temperature oxidation and erosion. In the present study, the performance of candidate materials was evaluated through a series of abrasion erosion experiments at room temperature as well as at 800 °C. Wear in metallic and refractory type materials was investigated using CarboBead® HSP 40/70 particles inside a resistance heated kiln. Furthermore, cross-sectional scanning electron microscopy (SEM) and energy dispersive x-ray spectroscopy (EDS) analysis on the specimens tested at 800 °C determined that the specific wear rate in Inconel 740H and stainless steel 316 metallic specimens was influenced by the thermally grown oxide morphology. High chromium Inconel 740H specimens exhibited greater resistance to wear with a steady state specific wear rate of 1.92E-4 mm 3 N -1 m –1 compared to 5.7E-3 mm 3 N -1 m –1 for Stainless Steel 316.

14 SOLAR ENERGY↗
DOE OSTI2025

Erosion of high-Z refractory coatings for helicon plasma source window

Proto-MPEX (Materials Plasma Exposure eXperiment), a linear plasma device (LPD), using a high power radio frequency (RF) (⩾100 kW, 13.56 MHz) helicon plasma source, has suffered RF sheath-induced window erosion. The sputtered impurities from the window surface transport toward the downstream target affecting plasma-material interaction studies. The rectified sheath voltage formed was high enough to cause window erosion by light ions due to its low-Z components (e.g. Si 3 N 4 and AlN). Hence, we are proposing impurity mitigation strategies, which involve the application of a Faraday screen to lower the rectified sheath voltage and the application of high-Z refractory coatings on the existing window plasma-facing surface. In this work, we report the erosion of two different coatings, i.e., tantalum oxide (Ta 2 O 5 ) and hafnium oxide (HfO 2 ) on a silicon nitride (Si 3 N 4 ) window material under conditions of low-energy deuterium (D) ion impact, well below the Ta 2 O 5 sputtering energy threshold (i.e. 250 eV). The test samples were RF-biased and exposed to a high D-ion fluence (∼10 26 m −2 ) in Plasma Interaction with Surface Component Experimental Station (PISCES-A) LPD. The experimentally measured sputtering yields of the high-Z refractory coatings below the sputtering energy threshold of Ta 2 O 5 indicate an increased erosion due to the plasma impurities, especially due to oxygen. Improving the vacuum level could reduce the oxygen impurities and increase the lifespan of the coated helicon window for plasma operation. Post-surface analysis indicates no preferential erosion of oxygen or enrichment of the high-Z surface component. This is likely due to an effective energy transfer from the impurity ion for sputtering of the high-Z component in the coating. With the reduced rectified sheath voltage at the window surface and improved vacuum conditions, the proposed high-Z refractory coatings offer a promising solution for reducing window erosion in future MPEX plasma operations at ORNL.

RF bias↗
DOE OSTI2021

Beryllium-driven structural evolution at the divertor surface

Erosion of the beryllium first wall material in tokamak reactors has been shown to result in transport and deposition on the tungsten divertor. Experimental studies of beryllium implantation in tungsten indicate that mixed W–Be intermetallic deposits can form, which have lower melting temperatures than tungsten and can trap tritium at higher rates. To better understand the formation and growth rate of these intermetallics, we performed cumulative molecular dynamics (MD) simulations of both high and low energy beryllium deposition in tungsten. In both cases, a W–Be mixed material layer (MML) emerged at the surface within several nanoseconds, either through energetic implantation or a thermally-activated exchange mechanism, respectively. While some ordering of the material into intermetallics occurred, fully ordered structures did not emerge from the deposition simulations. Targeted MD simulations of the MML to further study the rate of Be diffusion and intermetallic growth rates indicate that for both cases, the gradual re-structuring of the material into an ordered intermetallic layer is beyond accessible MD time scales(≤1 μs). However, the rapid formation of the MML within nanoseconds indicates that beryllium deposition can influence other plasma species interactions at the surface and begin to alter the tungsten material properties. Therefore, beryllium deposition on the divertor surface, even in small amounts, is likely to cause significant changes in plasma-surface interactions and will need to be considered in future studies.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Tungsten–carbon surface evolution and erosion modeling for a small angle slot divertor in DIII-D

Abstract We modeled tungsten–carbon mixed surface evolution, sputtering erosion, and transport for the tungsten coated region of a small angle slot (SAS) divertor design for the DIII-D tokamak. This divertor concept aims to achieve a closed slot dissipative plasma to minimize heat load and surface erosion, and to study high- Z material performance. Our advanced simulations use coupled ITMC-DYN material mixing/response and 3D full kinetic REDEP/WBC erosion/redeposition code packages, with divertor plasma solution from the SOLPS-ITER package with 4 MW power input. The SAS design geometry and resulting in-slot plasma parameters cause significant differences in predicted sputter/transport from a conventional divertor. For 2% C/D incident plasma ratio, an equilibrium mixed C/W surface is attained at ∼30 s of discharge, from wall sputtered carbon transported to the 10 cm long tungsten divertor region. Tungsten remains exposed to the plasma, but the evolved surface composition varies with different C/D ratios. Tungsten is primarily sputtered from the mixed surface by impinging carbon ions in the +1 to +4 charge states, with some self-sputtering. Redeposition of sputtered tungsten to the divertor is significant, ∼80% along the higher plasma temperature attached plasma SAS entrance region, but this is less than the typically near-unity values for a conventional divertor. Plasma-incident carbon is highly backscattered (∼50%) from the mixed surface, with little redeposition (<10%); this helps maintain tungsten in the surface sputter zone. Carbon is mainly sputtered from the mixed surface by D + ions, also with low redeposition (∼10%–30%). Finally, the modeling shows non-zero but low sputtered tungsten current from the divertor to the core plasma direction. These results appear favorable for effective testing of a tungsten-containing SAS divertor in DIII-D, and extrapolation of mixed-material evolution/response findings to the analogous low- Z /high- Z , Be/W, ITER plasma facing system.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Predicting tungsten erosion and leakage properties for the new V-shaped small angle slot divertor in DIII-D

Impurity transport modeling of the new tungsten (W)-coated, V-shaped small angle slot (SAS) divertor in the DIII-D tokamak was conducted using the SOLPS-ITER plasma edge code package and the DIVIMP impurity tracking code. The inboard baffle of the current SAS divertor will be shifted closer to the outboard baffle, creating a V-corner at the slot vertex. In addition, the outboard baffle will be coated with 10–15 μm of W for experiments studying high-Z sourcing and leakage in a closed divertor. Modeling of the 'SAS-VW' divertor predicts that these changes to the inner baffle will reduce W gross erosion by 40× relative to the existing SAS divertor when the outer strike point (OSP) is at the V-corner and the ion B × ∇B drift is towards the divertor, driven primarily by significant cooling near the slot vertex. Most W erosion in SAS-VW is expected to occur near the slot entrance, which may pose a higher risk to core contamination than W eroded deeper in the slot. Furthermore, adding a new sheath-based prompt redeposition model increases the sensitivity of redeposition estimates to near-target plasma conditions and may provide more accurate predictions of net erosion. Moving the OSP outboard from the slot vertex ~4 cm onto the W-coated region yields a 40× increase in the gross erosion rate and a 50% decrease in the core leakage fraction. Thus slight variations in strike point location may counteract the potential benefits of the tightly-baffled V slot on minimizing erosion. This impurity transport modeling provides useful guidance for future experiments on the SAS-VW divertor focused on high-Z erosion/redeposition, scrape-off layer transport, and core leakage.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Simulating Oxidation of Carbon Surfaces by Atomic Oxygen Coupled with a Finite Rate Oxidation Model

Oxidation is a prominent factor in degradation of carbon based ablative materials at high temperatures, resulting in mass loss and material recession through chemical and mechanical erosion. In this paper, a finite rate carbon oxidation model coupled with surface recession is implemented in the Porous Ablation and Thermal Response (Panther) software to investigate carbon oxidation by atomic oxygen over a range of temperatures and pressures. Panther is utilized to investigate the finite rate oxidation model proposed by Swaminathan-Gopalan et al. at conditions of higher pressure and flux relative to the experiments it was built on.

Kirmanoglu, Kaan K.↗
DOE OSTI2025

Effects of oxidation and impurities in lithium surfaces on the emitting wall plasma sheath

The use of lithium as a surface coating in fusion devices improves the plasma performance, but the change in the wall properties affects the secondary electron emission properties of the material. Lithium oxidizes easily, which drives the emission yield well above unity. We present here simulations demonstrating the change in the sheath structure from monotonic to the nonmonotonic space-charge limited sheath using an energy-dependent data-driven emission model, which self-consistently captures both secondary emission and backscattering populations. Increased secondary electron emission from the material has ramifications for the degradation and erosion of the wall. The results show that the oxidation leads to an increased electron energy flux into the wall and a reduced ion energy flux. The net transfer of energy to the surface is significantly greater for the oxidized case than for the pure lithium case. High backscattering rates of low-energy particles lead to a high re-emission rate at the wall.

Fusion reactors↗
DOE OSTI2020

Controls on the 36 Cl/Cl input ratio of paleo-groundwater in arid environments: New evidence from 81 Kr/Kr data

In this study, measurements of the long-lived 81 Kr and 36 Cl radioisotopes in groundwater from the Negev Desert (Israel) were used to assess the 36 Cl/Cl input ratios and Cl – contents for paleorecharge into the Nubian Sandstone Aquifer (NSA). The reconstructed Cl – content of the recharge flux was on the order of 300–400 mg/L. An initial 36 Cl/Cl ratio of 50 × 10 –15 was assessed for the groundwater replenishment in the Negev Desert since the late Pleistocene, in agreement with the 36 Cl/Cl ratios in recent local rainwater. This is despite possible changes in the climatic conditions and the 36 Cl production rates in the atmosphere over this timeframe. This similarity in values is explained by the major role played by the erosion and weathering of near-surface materials in the desert environment that dominate the hydrochemistry of rains, floods, and the consequent groundwater recharge. Spatial variation in the reconstructed initial 36 Cl/Cl ratio is accounted for by the differences in the mineral aerosol sources for specific recharge areas of the NSA. Accordingly, regional variations in the 36 Cl/Cl input in groundwater reservoirs surrounding the Mediterranean Sea indicate various processes that govern the 36 Cl/Cl system. Finally, the results of this study highlight the great advantage of integrating 81 Kr age information in evaluating the initial 36 Cl/Cl and Cl – input, which is essential for the calibration of 36 Cl radioisotope as an available long-term dating tool for a given basin.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

The effectiveness of D 2 pellet and gas injection in reducing intra-ELM tungsten erosion and heat flux in the DIII-D small angle slot divertor

Edge localized modes (ELMs) in H-mode plasmas can melt and erode plasma-facing components (PFCs) and lead to impurities in the core, reducing confinement. This study analyzes the use of D 2 pellet and gas injection for ELM mitigation on the DIII-D tokamak during the 2022 Small Angle Slot V-shaped Tungsten (W) (SAS-VW) divertor campaign, reducing W erosion and heat flux during ELMs. D α (656 nm) and WI (400.9 nm) filterscopes and Langmuir probes provide photon emission and electron density/temperature to estimate W atom erosion using the S/XB method, while surface eroding thermocouples measured ELM peak heat flux at the outer strike point (OSP). Thomson Scattering measurements of pedestal T e and n e provided input to predict W divertor erosion and heat flux during ELMs via the Free-Streaming plus Recycling Model (FSRM). While a greater D 2 mass injection rate decreased the ELM peak heat flux, the impact on W erosion was not monotonic. The average ‘large’ intra-ELM W erosion was lower for plasma shots with D 2 mass injection compared to the plasma shots without any D 2 mass injection in the SAS-VW divertor. However, plasma shots did not see significant changes in ‘large’ intra-ELM W divertor erosion as the D 2 mass injection rate increased. On average, the FSRM overestimated SAS-VW experimental intra-ELM W erosion by a factor of 6.9, but the overestimation is reduced to a factor of 3.6 with the implication of C deposition effects. Generally, experimentally measured and predicted quantities were worse for plasma shots with a lower D 2 mass injection rate and corresponding higher plasma carbon (C) impurity percentage (f C ). The discrepancies are postulated to be due to C/W material mixing, for which a simple analytic mixed-material model is presented. These results highlight the importance of incorporating and improving the robustness of a mixed-material layer model in the analysis of PFC erosion on present and future tokamak devices.

Carbon (C)↗
DOE OSTI2023

ELM sputter erosion modeling of a tungsten coated small angle slot divertor in DIII-D

We modeled plasma edge localized mode (ELM) sputter erosion for a Small Angle Slot divertor with a tungsten coated region (SAS-VW), designed for experiments in the DIII-D tokamak, and proposed for use in future advanced tokamaks. The simulations use a free-streaming, 1000 eV, C +6 and D +1 ELM impingement model, with SOLPS-ITER, ITMC-DYN, and REDEP/WBC code packages for background plasma, material response, and erosion/redeposition respectively. The results show ELM'ing plasma gross and net tungsten erosion fluxes of the mixed-material C/W surface peaking at the slot entrance region, and an order of magnitude higher than for non-ELMs. The per-pulse erosion, however, remains low, of order 0.5 nm, due to expected moderate ELM frequencies and duration in DIII-D. Here, the ELMs result in a ~25x higher peak sputtered W current leaving the divertor slot region, towards the core plasma, compared to the ELM-free plasma case. The time-integrated escape current, however, may not significantly affect core plasma high-Z contamination concerns, for a 1% ELM duty factor, but may be an issue for higher frequency ELMs. In general, the modeling results appear favorable for effective testing of the SAS-VW divertor in DIII-D, and extrapolation to innovative divertor designs in future ITER-like and DEMO fusion devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Organic carbon burial by river meandering partially offsets bank erosion carbon fluxes in a discontinuous permafrost floodplain

Abstract. Arctic river systems erode permafrost in their banks and mobilize particulate organic carbon (OC). Meandering rivers can entrain particulate OC from permafrost many meters below the depth of annual thaw, potentially enabling the production of greenhouse gases. However, the amount and fate of permafrost OC that is mobilized by river erosion is uncertain. To constrain OC fluxes due to riverbank erosion and deposition, we collected riverbank and floodplain sediment samples along the Koyukuk River, which meanders through discontinuous permafrost in the Yukon River watershed, Alaska, USA, with an average migration rate of 0.52 m yr−1. We measured sediment total OC (TOC) content, radiocarbon activity, water content, bulk density, grain size, and floodplain stratigraphy. Radiocarbon activity and TOC content were higher in samples dominated by silt as compared to sand, which we used to map OC content onto floodplain stratigraphy and estimate carbon fluxes due to river meandering. Results showed that the Koyukuk River erodes and re-deposits a substantial flux of OC each year due to its depth and high migration rate, generating a combined OC flux of a similar magnitude to the floodplain net ecological productivity. However, sediment being eroded from cutbanks and deposited as point bars had similar OC stocks (mean ± 1 SD of 125.3±13.1 kg OC m−2 in cutbanks versus 114.0±15.7 kg OC m−2 in point bars) whether or not the banks contained permafrost. We also observed radiocarbon-depleted biospheric OC in both cutbanks and permafrost-free point bars. These results indicate that a substantial fraction of aged biospheric OC that is liberated from floodplains by bank erosion is subsequently re-deposited in point bars rather than being oxidized. The process of aging, erosion, and re-deposition of floodplain organic material may be intrinsic to river–floodplain dynamics, regardless of permafrost content.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Towards an understanding of particle-scale flaws and microstructure evolution in cold spray via accumulation of single particle impacts

Cold spray coatings are the sum of countless individual bonding events between single particles impacting on top of one another at high velocities. Thus, the collective behavior of microparticles must be considered to elucidate the origins of coating flaws at the scale of the particles and larger, or the dynamic evolution of the overall coating microstructure. Laser-induced particle impact testing (LIPIT) has been extensively used to study single-particle impacts, and in this work is adapted to study the accumulation of numerous particles with knowledge of each individual particle's impact parameters (particle size, velocity). The method reproducibly deposits stacks of gold particles (>20 particles) with different characteristic spectra of impact velocity. The observation of impact-induced erosion lets us define a critical velocity for material-build-up that is higher than that for single-particle bonding. The quantitative single-particle data are analyzed in a correlative manner to the structure and flaws in the resulting stacks, providing some first statistical connections between, e.g., strain and recrystallization, or aberrant particle characteristics and defects. The results highlight opportunities for the study of many-particle phenomena in microparticle impact—from interaction of particles in cold spray to multi-step erosion processes—with a quantitative view of the behavior of single particles.

Erosion↗