Search NASA⌕ Search

SEARCH · Search NASA

Results for “Mars EDL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

MARS 2020 Backshell Radiative Heating Measurement and Shock Tube Verification

In February 2021, the Perseverance rover was brought to the surface of Mars by the Mars 2020 mission. A feature of the Mars 2020 capsule was instrumentation to measure its entry, descent and landing (EDL) with the so-called Mars EDL Instrumentation 2 (MEDLI2) [1]. The MEDLI2 introduced, among other things, backshell instrumentation, including a broadband radiometer. The radiometer was mounted on the leeside of the vehicle next to thermocouple plugs and a heat flux gauge. The data returned by the leeside MEDLI2 heat flux gauge is largely analogous to that measured by the COMARS gauge flown on the ExoMars Schiaparelli [2] entry in that it is measuring heat flux in an area that is entirely dominated by radiative heating. The COMARS measurement provided excellent validation of backshell radiative heating models for Mars entry, albeit at a limited number of points [3]. The MEDLI2 heat flux gauge measurement effectively confirmed the quality of the prediction, extended over the full trajectory, as will be presented in this paper. The MEDLI2 radiometer,however, was blocked by ablation products and suffered a loss of half of its signal. The second backshell heat flux gauge installed on the windside of the vehicle was also well predicted, although the heating had both radiative and convective contributions. It was desired to reproduce the conditions of the Mars 2020 entry via ground testing in the Electric Arc Shock Tube (EAST) at NASA Ames. Tests to verify stagnation line heating were previously reported in EAST, confirming the presence of shock layer radiation as the major discrepancy in heatshield temperature modelling [4]. Therefore, tests for stagnation line heating were not repeated. Instead, the shock tube informed bias method [5, 6] was used to identify test conditions that may produce similarity to streamlines that pass around the backside of the vehicle and are responsible for the radiation observed at the two heat flux gauge locations. This method was used to identify a range of velocities and densities in the shock tube that are relevant for confirming the radiative environment encountered. This paper reports the results obtained in the 10 cm diameter EAST shock tube, corresponding to later trajectory points at ambient pressures of 1.1-2.0 Torr and velocities from 1.2-3.5 km/s. The test series employed two primary diagnostics: emission spectroscopy and tunable diode laser absorption spectroscopy (TDLAS). The emission spectroscopy performed broadband measurements of the radiative emission of the 4.3 and 2.7 m bands of CO2 at flight similar conditions, obtaining both spectral and spatial data corresponding to the relaxation behind the shock front. The TDLAS measured the absorption of several lines of CO and CO2 and obtains species number densities and temperatures as a function of time behind the shock front. This paper will review highlights of this test series and analyses of the emission and absorption data. While the datasets generally show good agreement with predictions, a few discrepancies and items for additional investigation are identified and will be discussed

Brett A Cruden↗
NASA NTRSDate not supplied

Scale-Resolving Simulations of a Supersonic Retro-Propulsion Concept For Mars Entry, Descent, and Landing

Supersonic retro-propulsion (SRP) is a deceleration technology that could enable largerpayloads and potentially humans to be brought from space to the surface of Mars safely.Accurate and reliable CFD predictions are needed to help design future Mars entry, descent,and landing (EDL) vehicles due to the cost and limitations of wind tunnel tests. TypicalCFD approaches struggle at points along the Mars EDL trajectory with high enough altitude(low enough ambient pressure) that the SRP motor plumes are over-expanded. This workdemonstrates how high-order scale-resolving simulations on Cartesian AMR grids can provideaccurate and reliable time-averaged aerodynamic loads on the vehicle for this challengingflow regime. Greater than second order convergence in the time-averaged integrated axialforce𝐶𝐴is obtained across the three finest mesh resolutions simulated, and the estimateduncertainty is smaller than the unsteady standard deviation – demonstrating the accuracy andreliability of the method. Although costly, this approach can yield higher confidence in𝐶𝐴thanpreviously obtained in a reasonable turnaround time and is within reach for a few points in thetrajectory (i.e. Mach 2.4, 2.52, and 2.78). Further computational performance and numericalmethods improvements are needed to reduce the cost enough to bring this method into the EDLengineering design cycle.

S&M↗
NASA NTRS2012

MSL DSENDS EDL Analysis and Operations

This paper presents the operations experience of the JPL EDL (Entry, Descent, and Landing) trajectory simulation team, focusing on events in the week before landing and EDL itself. A brief description of the EDL trajectory simulation tool used for targeting and simulation verification analysis will be presented, including a high level discussion of the required modeling. Initialization and output interfaces used for landing hazard analysis will also be covered, along with discussion of real-time EDL event detection using radiometric Doppler data.

Entry, descent, and landing (EDL)↗
NASA NTRS2015

Aerodynamic Models for the Low Density Supersonic Declerator (LDSD) Supersonic Flight Dynamics Test (SFDT)

An overview of pre-flight aerodynamic models for the Low Density Supersonic Decelerator (LDSD) Supersonic Flight Dynamics Test (SFDT) campaign is presented, with comparisons to reconstructed flight data and discussion of model updates. The SFDT campaign objective is to test Supersonic Inflatable Aerodynamic Decelerator (SIAD) and large supersonic parachute technologies at high altitude Earth conditions relevant to entry, descent, and landing (EDL) at Mars. Nominal SIAD test conditions are attained by lifting a test vehicle (TV) to 36 km altitude with a large helium balloon, then accelerating the TV to Mach 4 and and 53 km altitude with a solid rocket motor. The first flight test (SFDT-1) delivered a 6 meter diameter robotic mission class decelerator (SIAD-R) to several seconds of flight on June 28, 2014, and was successful in demonstrating the SFDT flight system concept and SIAD-R. The trajectory was off-nominal, however, lofting to over 8 km higher than predicted in flight simulations. Comparisons between reconstructed flight data and aerodynamic models show that SIAD-R aerodynamic performance was in good agreement with pre-flight predictions. Similar comparisons of powered ascent phase aerodynamics show that the pre-flight model overpredicted TV pitch stability, leading to underprediction of trajectory peak altitude. Comparisons between pre-flight aerodynamic models and reconstructed flight data are shown, and changes to aerodynamic models using improved fidelity and knowledge gained from SFDT-1 are discussed.

Van Norman, John W.↗
NASA NTRS2016

Aerodynamic Models for the Low Density Supersonic Decelerator (LDSD) Test Vehicles

An overview of aerodynamic models for the Low Density Supersonic Decelerator (LDSD) Supersonic Flight Dynamics Test (SFDT) campaign test vehicle is presented, with comparisons to reconstructed flight data and discussion of model updates. The SFDT campaign objective is to test Supersonic Inflatable Aerodynamic Decelerator (SIAD) and large supersonic parachute technologies at high altitude Earth conditions relevant to entry, descent, and landing (EDL) at Mars. Nominal SIAD test conditions are attained by lifting a test vehicle (TV) to 36 km altitude with a helium balloon, then accelerating the TV to Mach 4 and 53 km altitude with a solid rocket motor. Test flights conducted in June of 2014 (SFDT-1) and 2015 (SFDT-2) each successfully delivered a 6 meter diameter decelerator (SIAD-R) to test conditions and several seconds of flight, and were successful in demonstrating the SFDT flight system concept and SIAD-R technology. Aerodynamic models and uncertainties developed for the SFDT campaign are presented, including the methods used to generate them and their implementation within an aerodynamic database (ADB) routine for flight simulations. Pre- and post-flight aerodynamic models are compared against reconstructed flight data and model changes based upon knowledge gained from the flights are discussed. The pre-flight powered phase model is shown to have a significant contribution to off-nominal SFDT trajectory lofting, while coast and SIAD phase models behaved much as predicted.

Van Norman, John W.↗
NASA NTRS2017

Mars Science Laboratory Heatshield Flight Data Analysis

NASA Mars Science Laboratory (MSL), which landed the Curiosity rover on the surface of Mars on August 5th, 2012, was the largest and heaviest Mars entry vehicle representing a significant advancement in planetary entry, descent and landing capability. Hypersonic flight performance data was collected using MSLs on-board sensors called Mars Entry, Descent and Landing Instrumentation (MEDLI). This talk will give an overview of MSL entry and a description of MEDLI sensors. Observations from flight data will be examined followed by a discussion of analysis efforts to reconstruct surface heating from heatshields in-depth temperature measurements. Finally, a brief overview of MEDLI2 instrumentation, which will fly on NASAs Mars2020 mission, will be presented with a discussion on how lessons learned from MEDLI data affected the design of MEDLI2 instrumentation.

Mars↗
NASA NTRSDate not supplied

Enabling New and Innovative Low Cost Mars Science Missions with the Adaptable, Deployable, Entry and Placement Technology (ADEPT)

The Adaptive Deployable Entry and Placement Technology (ADEPT) offers a delivery capability for Small Sat or CubeSat orbiter(s), in-situ elements, or landers. ADEPT can deliver the same science payload to a destination with a stowed diameter a factor of 3-4 times smaller than an equivalent rigid aeroshell, alleviating volumetric constraints on the secondary payload accommodation or primary carrier spacecraft bus. The ADEPT system can support payload over a range of mass and geometries to offer a delivery capability for a single or constellation of spacecraft supporting the goals and objectives of “Low Cost Mars Science Missions.”

ADEPT↗
NASA NTRSDate not supplied

Status of Mars Retropropulsion Testing in the Langley Unitary Plan Wind Tunnel

Future Mars human landings will be enabled by a powered descent phase starting at supersonic conditions, something which has never been done before on a Mars mission. Significant aerosciences challenges exist due to jet interactions between the retrorocket engine plumes, freestream flow, and vehicle that will affect the aerodynamic behavior during powered descent. Historically, wind tunnel tests have been used to study the interactions with inert gas exhaust simulants in place of rocket engines. On the computational side, flowfield simulations have been completed at full-scale conditions, but the available ground and flight data are not appropriate for calibrating computational uncertainties for aerodynamic interference on proposed Mars descent vehicles, due to insufficient data, dissimilar vehicle geometries, and disparate operating conditions. A wind tunnel test has been designed to begin addressing powered descent aerodynamics risks for large-scale human Mars entry concepts and to identify gaps in computational predictive capabilities. The test will be conducted in the NASA Langley Unitary Plan Wind Tunnel and is designed with improvements in model design and data products over past tests. The test campaign will be run using sub-scale model geometries derived from NASA powered descent reference vehicles: a blunt low lift-to-drag vehicle and a more slender geometry that generates higher unpowered lift. Both models have been fabricated and are ready for testing. The blunt model is equipped with the flexibility to examine the effects of nozzle pointing direction, number, location, size, and area ratio. The main measurements are heatshield aerodynamic interference forces and moments with a custom flow-through balance, discrete and distributed heatshield pressure, and high-speed flowfield visualization. This paper covers the test objectives, facility, models and instrumentation, and planned test matrix.

Supersonic Retropropulsion↗
NASA NTRSDate not supplied

Computational Modeling of Mars Retropropulsion Concepts in the Langley Unitary Plan Wind Tunnel

Future human Mars missions will require powered descent starting at supersonic conditions, something which has never been done before at Mars. Computational powered descent flowfield simulations have been completed at full-scale Mars conditions, but the available ground test data are not appropriate for calibrating computational uncertainties for aerodynamic interference on proposed Mars descent vehicles. A test will be conducted in the NASA Langley Unitary Plan Wind Tunnel to begin addressing powered descent aerodynamics risks for large-scale human Mars entry concepts and to identify gaps in computational predictive capabilities. This paper covers pre-test computational flowfield predictions of two different models derived from full-scale reference vehicles: a blunt low lift-to-drag vehicle and a more slender geometry. Calculations of the blunt model include variations in nozzle configuration: nozzle location, size, area ratio, and pointing direction. There exist some significant differences between solvers, but some general trends are observed from simulations of the blunt model. First, aerodynamic axial force from the heatshield decreases with increasing thrust due to expanding plume blockage. Second, nozzles that point along the model axis result in lower aerodynamic axial force compared to nozzles that have a radial thrust component. Finally, placing the nozzles further away from the model nose preserves more heatshield axial force with increasing thrust compared to nozzles that are closer to the nose. For the slender model, the axial force from the heatshield is similar to the non-blowing axial force regardless of thrust magnitude, due to the nozzle arrangement on the heatshield. Once the test is completed, direct comparisons between the computations and test data will be made to determine computational uncertainties in a wind tunnel environment, to identify gaps in predictive capabilities, and to inform planning for future ground and flight test programs for Mars powered descent vehicles.

Supersonic Retropropulsion↗
NASA NTRSDate not supplied

Development Status of Powered Descent for High-Mass Mars Entry, Descent, and Landing Systems

Retropropulsion, initiated at supersonic conditions, provides both deceleration and control authority as an enabling capability for the delivery of human-scale payloads to the surface of Mars. There are no other presently viable approaches to the descent phase of flight for vehicles of such scales. NASA continues to dedicate investment in the maturation of powered descent in atmospheric environments, for the express application to large-scale entry, descent, and landing systems. Efforts focus on parametric, subscale, inert gas ground testing, rigorous validation of computational modeling approaches against these data, and the implementation of highly efficient, scalable simulation tools. This paper summarizes the current maturity of retropropulsion in a free-flight, atmospheric environment for vehicles with significant aerodynamic surface area, as well as the current status of efforts within NASA for ground testing, computational simulation, and flight testing.

Mars↗
NASA NTRSDate not supplied

Post-Flight EDL Entry Guidance for the Mars 2020 Mission

Like its predecessor Mars Science Laboratory, the Mars 2020 mission successfully utilized a derivative of the Apollo Entry Terminal Point Controller guidance algorithm, whereby bank angle controls range flown along a trajectory. The flight performance of this algorithm in conjunction with a range-trigger for parachute deploy delivered the Perseverance rover to 1.7 km from the expected touchdown location within an ellipse of 7.5 x 5.2 km. This miss distance is largely attributed to atmospheric and aerodynamic modeling uncertainties between the design and as-flown trajectory. This algorithm for guided entry continues to provide a solid basis for Mars missions to improve upon.

Guidance↗
NASA NTRS2005

Mars Exploration Rover Entry, Descent, and Landing: A Thermal Perspective

Perhaps the most challenging mission phase for the Mars Exploration Rovers was the Entry, Descent, and Landing (EDL). During this phase, the entry vehicle attached to its cruise stage was transformed into a stowed tetrahedral Lander that was surrounded by inflated airbags through a series of complex events. There was only one opportunity to successfully execute an automated command sequence without any possible ground intervention. The success of EDL was reliant upon the system thermal design: 1) to thermally condition EDL hardware from cruise storage temperatures to operating temperature ranges; 2) to maintain the Rover electronics within operating temperature ranges without the benefit of the cruise single phase cooling loop, which had been evacuated in preparation for EDL; and 3) to maintain the cruise stage propulsion components for the critical turn to entry attitude. Since the EDL architecture was inherited from Mars Pathfinder (MPF), the initial EDL thermal design would be inherited from MPF. However, hardware and implementation differences from MPF ultimately changed the MPF inheritance approach for the EDL thermal design. With the lack of full inheritance, the verification and validation of the EDL thermal design took on increased significance. This paper will summarize the verification and validation approach for the EDL thermal design along with applicable system level thermal testing results as well as appropriate thermal analyses. In addition, the lessons learned during the system-level testing will be discussed. Finally, the in-flight EDL experiences of both MER-A and -B missions (Spirit and Opportunity, respectively) will be presented, demonstrated how lessons learned from Spirit were applied to Opportunity.

thermal↗
NASA NTRS2019

Atmospheric impacts on EDL maneuver targeting for the InSight mission and unguided Mars landers

Early in operational testing for the InSight mission to Mars, it was discovered that the final maneuver to target the entry-interface point (EIP) was unexpectedly sensitive, in both magnitude and direction, to planned atmosphere model updates that would be based on real-time measurements of the Martian atmosphere by Mars Reconnaissance Orbiter (MRO). Upon investigation, the team realized that the Phoenix mission also discovered this sensitivity during its operational testing. A further investigation identified that maneuver sensitivity to real-time atmosphere updates was a result of the fact that both the EFPA and ground target were being held fixed, constraining the maneuver in a way that forced the entry time to change in order to compensate for changes to the nominal trajectory from updating the atmosphere model. The final maneuver occurs 22 hours prior to entry, at which point it is very expensive to change entry time. The study also revealed that any unguided Mars entry, descent, and landing (EDL) mission would be impacted by this sensitivity if it used real-time atmosphere observations to model the nominal expected atmosphere used for maneuver targeting of the EIP. This paper discusses the results of that investigation and presents a number of mitigations as well as the consequences of ignoring the sensitivity.

Kipp, Devin↗