Search NASA⌕ Search

SEARCH · Search NASA

Results for “Maximum light use efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

High-efficiency solar thermophotovoltaic system using a nanostructure-based selective emitter

Herein, we present the design, fabrication, optimization, and experimental results of a high-efficiency planar solar thermophotovoltaic (STPV) system utilizing a micro-textured absorber and a nanostructure multilayer metal-dielectric coated selective emitter fabricated on a tungsten (W) substrate. Light absorptance of more than 90% was achieved at visible and near-infrared wavelengths using the microtextured absorbing surface. The nanostructure selective emitter consists of two thin-film optical coatings of silicon nitride (Si3N4) and a layer of W in between to increase the surface emissivity in spectral regimes matching the quantum efficiency of the thermophotovoltaic (TPV) cells. Gallium antimonide (GaSb)-based TPV cells are used in our STPV design. The experiment was conducted at different operating temperatures using a high-power continuous wave laser diode stack as a simulated source of concentrated incident radiation. Our experimental setup measured a maximum electrical output power density of 1.71 W/cm 2 at 1676 K STPV temperature, and the overall power conversion efficiency of 8.4% after normalizing the output power density to the emitter area. This is the highest STPV system efficiency reported so far for any experimental STPV device. The incident optical laser power on the absorber side was 131 W. This is equivalent to a solar concentration factor of ~2100, which is within the practical limit and readily achievable with Fresnel lens setup.

14 SOLAR ENERGY↗
DOE OSTI2022

Experimental Studies of Low-Load Limit in a Stoichiometric Micro-Pilot Diesel Natural Gas Engine

While operating at light loads, diesel pilot-ignited natural gas engines with lean premixed natural gas suffer from poor combustion efficiency and high methane emissions. This work investigates the limits of low-load operation for a micro-pilot diesel natural gas engine that uses a stoichiometric mixture to enable methane and nitrogen oxide emission control. By optimizing engine hardware, operating conditions, and injection strategies, this study focused on defining the lowest achievable load while maintaining a stoichiometric equivalence ratio and with acceptable combustion stability. A multi-cylinder diesel 6.7 L engine was converted to run natural gas premix with a maximum diesel micro-pilot contribution of 10%. With a base diesel compression ratio of 17.3:1, the intake manifold pressure limit was 80 kPa(absolute). At a reduced compression ratio of 15:1, this limit increased to 85 kPa, raising the minimum stable load. Retarding the combustion phasing, typically used in spark-ignition engines to achieve lower loads, was also tested but found to be limited by degraded diesel ignition at later timings. Reducing the pilot injection pressure improved combustion stability, as did increasing pilot quantity at the cost of lower substitution ratios. The lean operation further reduced load but increased NOx and hydrocarbon emissions. At loads below the practical dual-fuel limit, a transition to lean diesel operation will likely be required with corresponding implications for the aftertreatment system.

03 NATURAL GAS↗
DOE OSTI2025

In Situ MOVPE Smoothing of Acoustically Spalled GaAs for Substrate Reuse

High material costs, especially for substrates, have limited the widespread adoption of III-V photovoltaics. A potential to reduce this cost is to reuse the III-V substrate via acoustic spalling, however this technique can leave a rough surface, hindering subsequent device performance. This research investigates the potential of using metalorganic vapor-phase epitaxy growth as a buffer layer to smooth the surface of acoustically spalled germanium and gallium arsenide (GaAs) substrates for improved III-V photovoltaic cell yield and performance, while retaining the maximum number of reuses of a substrate. Three potential smoothing layers were explored: lightly doped C:GaAs, highly doped Se:GaInP, and lightly doped Se:GaInP. C:GaAs showed the most promise as a smoothing layer, while Se:GaInP tended to conform to the underlying morphology, potentially increasing roughness in some areas. Utilizing 5 ..mu..m of C:GaAs as a planarizing buffer increased the average efficiency (without an antireflection coating) from an as-spalled baseline from 2.1% to 4.9% and performing a 5-min 30 degrees C 8:1:1 H2SO4:H2O2:H2O etch prior to a 5 ..mu..m of C:GaAs as a planarizing buffer further increased efficiency to 11.1%.

14 SOLAR ENERGY↗
DOE OSTI2025

One Pot Synthesis of Cyan Emitting CdZnSSe Quantum Dots for Human Centric Lighting

A one pot synthesis of blue and green emissive CdZnSSe quantum dots (QDs) from thio- and selenoureas and Cd and Zn carboxylates is optimized using high throughput robotic optimization. A large set of spectral data (N = 192) is used to train machine learning models that accurately predict the photoluminescence emission wavelength (λmax) and full-width half-maximum, and the relative photoluminescence quantum yield (PLQY) from the S:Se and Zn:Cd stoichiometries and reaction time. ZnS shells are deposited on the crude QD heterostructures using 4-tert-butylbenzyl mercaptan, a more reactive source of sulfide that enables shell growth below the temperature where ion diffusion in the QD can broaden its optical spectrum (≤275 °C). These optimized procedures provide gram quantities of blue-green emitting QDs (PLQY = 85–99%) in a single reaction vessel. A solid state lighting device (4260 K) that incorporates cyan emissive QDs achieved a higher luminous efficacy of 179 lm/W and melanopic daylight efficiency ratio (0.71) than existing commercial human centric lighting devices.

Jordan, Abraham J↗
DOE OSTI2025

Plasmon-enhanced ultralow-threshold solid-state triplet fusion upconversion

Triplet fusion upconversion has potential applications in solar cells, photoredox catalysis, additive manufacturing and bioimaging. However, solid-state upconversion systems have struggled to measure up to their solution-phase counterparts, often requiring enormous optical power densities to operate at the maximum efficiency. Here we substantially improve the performance of upconversion films through excitation with surface plasmons that propagate along a planar silver-film interface, leading to an absorption enhancement that reduces the intensity threshold I th by a factor of 19 and enhances the external quantum efficiency by a factor of 17. From this, we achieve I th values as low as 3.4 mW cm −2 and an external quantum efficiency up to 0.094%. To demonstrate real-world viability, we couple the upconversion film to plasmons generated by the near-field of excitons in an organic light-emitting diode. As a result, this scheme is then used to fabricate a white-emitting organic light-emitting diode where blue emission sources from plasmon-excited upconversion, achieving a high colour rendering index of 86.2 and setting precedent for blue emission in the absence of high-energy polarons or triplets.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Ion acceleration from microstructured targets irradiated by high-intensity picosecond laser pulses

Structures on the front surface of thin foil targets for laser-driven ion acceleration have been proposed to increase the ion source maximum energy and conversion efficiency. While structures have been shown to significantly boost the proton acceleration from pulses of moderate-energy fluence, their performance on tightly focused and high-energy lasers remains unclear. Here, we report the results of laser-driven three-dimensional (3D)-printed microtube targets, focusing on their efficacy for ion acceleration. Using the high-contrast (~10 12) PHELIX laser (150 J, 10 21 W / cm 2 ), we studied the acceleration of ions from 1-μm-thick foils covered with micropillars or microtubes, which we compared with flat foils. The front-surface structures significantly increased the conversion efficiency from laser to light ions, with up to a factor of 5 higher proton number with respect to a flat target, albeit without an increase of the cutoff energy. An optimum diameter was found for the microtube targets. Our findings in this work are supported by a systematic particle-in-cell modeling investigation of ion acceleration using 2D simulations with various structure dimensions. Simulations reproduce the experimental data with good agreement, including the observation of the optimum tube diameter, and reveal that the laser is shuttered by the plasma filling the tubes, explaining why the ion cutoff energy was not increased in this regime.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2026

Oversizing and Part-Load Problems

Oversizing, the common engineering practice of specifying devices with capacity exceeding the actual load requirement, is a widespread practice across virtually all building technologies end-use categories, including HVAC, electrical systems, lighting, appliances, and plug loads. This practice, driven by factors like design uncertainty, institutional pressures, and risk aversion, results in wasted capital investment, control difficulties, and excessive energy consumption due to inefficient part-load operation. Part-load operation, where devices run below maximum capacity, is the dominant operating mode in most energy systems and presents a complex design challenge. Solutions to match output to load fall into three broad categories: constraining the output, adjusting the device’s internal behavior, and linking output to energy storage or other waste-heat reuse applications. The energy implications of part-load are critical, as efficiency often drops sharply as load decreases across a wide diversity of devices. To quantify the extent of this problem, we derive a dimensionless Part-Load Metric (PLM) based on device efficiency and its frequency distribution of operating hours at various output levels. The PLM quantifies the deviation of a device's actual efficiency from its maximum design efficiency. This metric also serves as a measure of "capital inefficiency," enabling engineers to compare the impact of different part-load solutions and providing a unified framework for evaluating performance across various devices and systems.

Meier, Alan↗
DOE OSTI2025

Thermomechanical Modeling and Analysis of a High-Temperature Light Trapping Planar Cavity Receiver

Solar energy harnessed through concentrating solar power (CSP) systems offers a promising path to sustainable energy production, with the efficiency and longevity of these systems relying on key components like solar receivers. This study analyzes the thermomechanical behavior of an innovative enclosed light-trapping solar receiver optimized for particle heating applications. The receiver utilizes sheet metal alloys to form enclosed cavities that reflect and trap incoming solar flux, as well as enclosed channels that contain fluidized particle beds absorbing solar heat. Finite element analysis (FEA) is applied to predict the receiver's thermomechanical performance under extreme solar flux conditions. Temperature distributions from a thermal model simulating a multi-panel assembly at steady state are input into the FEA thermomechanical model for stress analysis. A key aspect of the analysis focuses on evaluating creep-fatigue damage, with a design target of achieving a 30- year service life. Various stress relief techniques are also proposed to extend the receiver's service life. The results highlight the significant impact of the particle-to-wall heat transfer coefficients (HTCs), ranging from 800 W/m2*K to 1400 W/m2*K. The 800 W/m2*K case shows a maximum von Mises stress of 164 MPa, while the 1400 W/m2*K case reduces it to 150 MPa. The creep life increases from 4,000 hrs in the 800 W/m2*K case to over 100,000 hrs in the 1400 W/m2*K case with Inconel 740H used, indicating that higher HTCs reduce stress and extend lifespan. This research advances the design of high-efficiency, low-stress solar receivers for particle-based thermal energy storage in CSP and industrial heating applications.

concentrating solar power↗
DOE OSTI2021

A transmissive concentrator photovoltaic module with cells directly cooled by silicone oil for solar cogeneration systems

Hybrid concentrator photovoltaic-thermal systems can cogenerate electricity and heat by beam-splitting incoming concentrated light onto photovoltaic cells and a thermal receiver to increase total conversion efficiency and potentially reduce system cost. To demonstrate this, we have designed and prototyped a transmissive spectrum-splitting concentrator photovoltaic module that maximizes solar energy conversion by utilizing the entire solar spectrum. Visible light is collected using infrared-transmissive triple-junction photovoltaic cells to achieve an in-band module efficiency of 43.3% for light of wavelength λ < 873 nm, while 44.2% of out-of-band light with λ > 873 nm is transmitted through for collection by a thermal receiver. During testing on a dual-axis tracked parabolic concentrator dish at up to 166 suns, cell temperatures were maintained at 119 °C or below via a novel active cooling method. This cooling system strictly flows silicone oil directly across both sides of the cells, without inhibiting optical transmission, as verified through experimentation and simulation. The module was validated outdoors for 572 sun·hrs, and achieved a maximum thermal receiver temperature of 180 °C. 86.1% of incident solar power is collected at 166 suns average concentration collectively among the electrical, cooling, and thermal receiver subsystems. The remaining 13.9% is lost to mirror reflectivity, dish shadowing, receiver reflection, and thermal losses. The ability to directly cool the cells with an inert silicone oil offers the potential for reduced system cost relative to previous transmissive hybrid concentrator photovoltaic-thermal systems, including microfluidic-cooled designs. This solar cogeneration capability is valuable in a wide range of commercial and industrial applications.

14 SOLAR ENERGY↗
DOE OSTI2023

Impact of Anatomical Fractionation of Corn Stover on Hammer Mill Throughput and Energy Consumption

The goal of this Case Study was to quantify the impacts of variable moisture and ash on hammer mill throughput and energy consumption and on loss of very wet stover that causes failures in the first stage grinder and that are not able to be fed to conversion, as compared to a status quo Base Case system. Also considered was convertible carbohydrate content (minimum total carbohydrate specification), maximum ash content and the delivered feedstock cost impacts of not being able to feed stover that did not meet the total carbohydrate specification to the conversion reactor. Laboratory data on the impacts of moisture content and tissue fraction on throughput and energy consumption in a stage 2 hammer mill were received from FCIC Subtask 5.1: Preprocessing, Corn Stover Preprocessing (Neal Yancey and Sergio Hernandez, INL). Additional air classifier throughput, energy consumption and separation efficiency data were obtained from FCIC Subtask 5.1 (Neal Yancey, INL) for the new air classifier, which has three exit streams (lights, middle and heavies). These data were utilized to develop the necessary response surface equations to perform throughput analysis using discrete event simulation. Because the ash contents and particle sizes had not been analyzed in the laboratory at the time of the model runs, we assumed that the ash distributed proportionally with total mass into the lights and heavies in an air classifier having two exit streams (lights and heavies) and that the lights fraction from the air classifier was not removed.

ash content↗
DOE OSTI2021

Triphenylamine/benzothiadiazole-based compounds for non-doped orange and red fluorescent OLEDs with high efficiencies and low efficiency roll-off

Long-wavelength materials are key for development of pure-color and white organic light-emitting devices (OLEDs). An organic molecule, combining hybridized local electron and charge-transfer (HLCT) states and aggregation-induced emission (AIE), not only breaks the 5% external quantum efficiency (EQE) limit but also overcomes emission quenching. Herein, we designed and synthesized four novel donor–acceptor compounds of TBAN, TBT, TBAT, and TABAT using triphenylamine (TPA) as the donor, benzothiadiazole (BT) as the acceptor, and anthracene (AN) as a bridge. We found that the emission peaks of TBAN, TBT, TBAT and TABAT are located at 596, 615, 580 and 546 nm, respectively. We successfully applied them to non-doped OLEDs, and the resulting devices exhibited excellent performance. For example, the optimal TBAN-based OLEDs showed a maximum luminance of 74 820 cd m –2 , a current efficiency of 12.1 cd A –1 and a maximum EQE of 5.7% with low roll-off. Additionally, the device with TBAN as both the emitter and hole-transport material also exhibited high efficiency that is comparable to that of an NPB-based device. Furthermore, this work demonstrates that it is feasible to obtain excellent orange and red emitters by employing BT- and TPA-based D–A architectures.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Graph Neural Networks for low-energy event classification & reconstruction in IceCube

IceCube, a cubic-kilometer array of optical sensors built to detect atmospheric and astrophysical neutrinos between 1 GeV and 1 PeV, is deployed 1.45 km to 2.45 km below the surface of the ice sheet at the South Pole. The classification and reconstruction of events from the in-ice detectors play a central role in the analysis of data from IceCube. Reconstructing and classifying events is a challenge due to the irregular detector geometry, inhomogeneous scattering and absorption of light in the ice and, below 100 GeV, the relatively low number of signal photons produced per event. To address this challenge, it is possible to represent IceCube events as point cloud graphs and use a Graph Neural Network (GNN) as the classification and reconstruction method. The GNN is capable of distinguishing neutrino events from cosmic-ray backgrounds, classifying different neutrino event types, and reconstructing the deposited energy, direction and interaction vertex. Based on simulation, we provide a comparison in the 1 GeV–100 GeV energy range to the current state-of-the-art maximum likelihood techniques used in current IceCube analyses, including the effects of known systematic uncertainties. For neutrino event classification, the GNN increases the signal efficiency by 18% at a fixed background rate, compared to current IceCube methods. Alternatively, the GNN offers a reduction of the background (i.e. false positive) rate by over a factor 8 (to below half a percent) at a fixed signal efficiency. For the reconstruction of energy, direction, and interaction vertex, the resolution improves by an average of 13%–20% compared to current maximum likelihood techniques in the energy range of 1 GeV–30 GeV. The GNN, when run on a GPU, is capable of processing IceCube events at a rate nearly double of the median IceCube trigger rate of 2.7 kHz, which opens the possibility of using low energy neutrinos in online searches for transient events.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

On the design and performance of InGaN/Si double-junction photocathodes

Via a combined theoretical and experimental study, we have investigated the synthesis and performance characteristics of InGaN/Si double-junction photoelectrochemical (PEC) water splitting devices, which promise a theoretical solar-to-hydrogen conversion efficiency ~30% under AM 1.5G one-sun illumination. The double-junction photocathodes consist of a p + -InGaN top light absorber and a Si bottom p-n junction, which are connected through a nanowire tunnel junction. The effect of indium composition of the top light absorber as well as the impact of p-type Mg dopant incorporation on the PEC performance was studied. Experimentally, the sample with 32% indium composition showed a maximum photocurrent density of ~9 mA/cm 2 at 0.4 mV vs reverse hydrogen electrode (RHE) with applied bias photon-to-current efficiency (ABPE) of ~9.5%. An optimum p-type doping level ~1 × 10 17 cm -3 was also identified, which results in the best device performance as a result of optimum surface band bending as well as vertical charge carrier (hole) transport. These results also show a good agreement with our theoretical analysis. This work provides significant insights in advancing the design and development of high efficiency PEC devices for artificial photosynthesis using industry ready materials, e.g., Si and GaN, to achieve large-scale, low-cost onsite hydrogen fuel production.

42 ENGINEERING↗
DOE OSTI2024

N-Terminal domain homologs of the orange carotenoid protein increase quenching of cyanobacterial phycobilisomes

Stress exerted by excess captured light energy in cyanobacteria is prevented by the photoprotective activity of the orange carotenoid protein (OCP). Under high light, the OCP converts from an orange, inactive form (OCP O ) into the red form (OCP R ) that binds to and quenches the phycobilisome (PBS). Structurally, the OCP consists of 2 domains: the N-terminal effector domain and a C-terminal regulatory domain. Structural analysis of the OCP-PBS complex showed that the N-terminal domains of an OCP dimer interact with the PBS core. These N-terminal OCP domains have single-domain protein paralogs known as helical carotenoid proteins (HCPs). Using PBS quenching assays, we show that the HCP4 and HCP5 homologs efficiently quench PBS fluorescence in vitro, surpassing the quenching ability of the OCP. This is consistent with computational quantum mechanics/molecular mechanics results. Interestingly, when using a maximum quenching concentration of OCP with PBSs, HCP5 addition further increases PBS quenching. Our results provide mechanistic insight into the quenching capacity and roles of HCP4 and HCP5 in cyanobacteria, suggesting that they are more than simply functionally redundant to the OCP.

Sheppard, Damien I.↗
DOE OSTI2023

Water alternative gas (WAG) optimization for a heterogeneous Brazilian pre-salt carbonate reservoir

Water alternating gas (WAG) is a cyclical process that involves alternating water and gas injections with the primary goal to improve sweep efficiency by maintaining initial high pressure, slowing water and gas breakthrough, and lowering oil viscosity. The objective of this work is to apply and optimize a WAG strategy on a carbonate field with light oil, compare it to the initially planned water-flooding strategy, and investigate the capability of WAG to improve field production. In this research, a compositional reservoir simulator was used to model a WAG process by injecting produced gas into the reservoir, using the same well structure as an optimized water-flooding strategy. Subsequently, a WAG strategy was created, optimizing the number and locations of wells, to facilitate a comparative analysis of the two recovery methods. The WAG optimization involved a detailed assessment of variables such as bottom hole pressure (BHP), WAG cycle duration, maximum gas oil ratio (GOR), and well positioning, to achieve a high net present value (NPV). The study focuses on the application of WAG optimization modeling in unconventional reservoirs, specifically pre-salt carbonate reservoirs, and investigates its implications on production strategy and forecast, emphasizing its potential for maximizing NPV and oil recovery in a recently producing field. The results showed that WAG improved reservoir performance when compared to water injection and produced a greater amount of oil. This solution showed potential to be tested under uncertainties (reservoir heterogeneity, faults, fractures, karsts, vugs, etc.) as future steps.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Design of a Nanophotonic Hybrid Coupler

This project aims to design and simulate a nanophotonic hybrid coupler for detecting vacuum ultraviolet (VUV) light with higher efficiency. VUV light is of significant interest because of its applications ranging from high energy physics to space science and electronic industry. However, current VUV photodetectors have very low efficiencies because most materials absorb in the VUV region (100-200 nm). To address this challenge, I have designed a plasmonic-dielectric coupler with wavelength shifting properties, enabling high Purcell enhancement and far-field confinement. The coupler consists of a cylindrical cSi resonator on top of a thin ZnO layer, and Ag and SiO2 are used as substrates. Simulations are done using the finite-difference time domain method to solve Maxwell’s equations, and specifically with Meep and Lumerical. The effectiveness of the coupler is characterized by the Purcell factor and far-field radiation. The Purcell factor reaches a maximum near 390 nm and is in the o rder of 10^4. Furthermore, the coupler also allows partial control of the directionality of the far-field radiation. With the presence of the resonator, the radiation is directed towards the coupled metalens. Overall, our design combines the advantages of plasmonic and dielectric couplers, along with the intrinsic wavelength shifting properties of materials to enhance VUV detection significantly, and such a device can be used in, for example, the DUNE project.

Zhou, Jiayang↗
DOE OSTI2020

Diazirine-based photo-crosslinkers for defect free fabrication of solution processed organic light-emitting diodes

The fabrication of solution deposited OLEDs is fraught with difficulties, largely due to the interlayer mixing and surface erosion during sequential deposition of the layers. We demonstrate that these problems can be circumvented by using photopolymerizable diazirine-based cross-linker capable of converting soluble organic materials into highly cross-linked insoluble networks. 3-Trifluoromethyl(aryl)diazirines photolyze readily upon the 10–15 min exposure of 365 nm UV irradiation to generate carbenes, which react with polymers or small molecules via C–H bond insertion producing highly cross-linked materials. This photo-generated cross-linking does not require any catalyst, initiator or short-wavelength UV light and is performed at room temperature, releasing molecular nitrogen as the only byproduct. To show the cross-linked polymer layers do not display inter-layer mixing, we deposited red-emitting regioregular poly(3-hexylthiophene-2,5-diyl) (P3HT) over cross-linked (10% cross-linker) blue emitting dioctyl polyfluorene (PFO) layer. The overlaid layers showed clear and well-defined boundary with no interlayer mixing. The surface morphology of the solution deposited layers was investigated by AFM to show that the cross-linked layers exhibited significant decrease in surface roughness. This is also shown on the example of the hole transporting material 4,4'-bis[N-(1-naphthyl)-N-phenylamino]-biphenyl (NPB) which displayed roughness average to decrease from 6.4 nm to 1.0 nm. The effect of decreased surface roughness on the performance of phosphorescent OLEDs was investigated by fabricating devices with configuration of ITO/PEDOT:PSS/NPB:(0%/5%/10%) cross-linker/MCP:6% Ir(mppy) 3 /TPBI/CsF/Al. Furthermore, following the diazirine-mediated cross-linking, the OLEDs displayed a decrease in turn-on voltage from 3.8 V to 3.0 V along with a six-fold enhancement of external quantum efficiency (EQE max ) from 1.1% to 6.8% and maximum luminous efficiency increase from 3.8 cd A -1 to 22.9 cd A -1 . These results demonstrate that the simple diazirine mediated photo-cross-linking using mild conditions compatible with organic layers is a promising strategy for improving the performance of the solution-processed OLEDs.

36 MATERIALS SCIENCE↗