Search NASA⌕ Search

SEARCH · Search NASA

Results for “Metallic systems”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Behavior of Combined Dielectric-Metallic Systems in a Charged Particle Environment

The charging and discharging characteristics of an electrically isolated solar array segment were studied in order to simulate discharges seen during geomagnetic substorms. A solar array segment was floated while bombarded with monoenergetic electrons at various angles of incidence. The potentials of the array surface and of the interconnects were monitored using Trek voltage probes to maintain electrical isolation. A back plate was capacitively coupled to the array to provide information on the characteristics of the transients accompanying the discharges. Several modes of discharging of the array were observed at relatively low differential and absolute potentials (a few kilovolts). A relatively slow discharge response in the array was observed, discharging over one second with currents of nanoamps. Two types of faster discharges were also seen which lasted a few hundredths of a millisecond and with currents on the order of microamps. Some results indicate an electron emission process associated with the arcs.

Gordon, W. L.↗

Joining of Zirconium Diboride-Based Ceramic Composites to Metallic Systems for High-Temperature Applications

Three types of hot-pressed zirconium diboride (ZrB2)-based ultra-high-temperature ceramic composites (UHTCC), ZrB2-SiC (ZS), ZrB2-SiC-C (ZSC), and ZrB2-SCS9-SiC (ZSS), were joined to Cu-clad-Mo using two Ag-Cu brazes (Cusil-ABA and Ticusil, T(sub L) approx.1073-1173 K) and two Pd-base brazes (Palco and Palni, T(sub L) approx.1493-1513 K). Scanning Electron Microscopy (SEM) coupled with energy-dispersive spectroscopy (EDS) revealed greater chemical interaction in joints made using Pd-base brazes than in joints made using Ag-Cu based active brazes. The degree of densification achieved in hot pressed composites influenced the Knoop hardness of the UHTCC and the hardness distribution across the braze interlayer. The braze region in Pd-base system displayed higher hardness in joints made using fully-dense ZS composites than in joints made using partially-dense ZSS composites and the carbon-containing ZSC composites. Calculations indicate a small negative elastic strain energy and an increase in the UHTCC's fracture stress up to a critical clad layer thickness . Above this critical thickness, strain energy in the UHTCC is positive, and it increases with increasing clad layer thickness. Empirical projections show a reduction in the effective thermal resistance of the joints and highlight the potential benefits of joining the UHTCC to Cu-clad-Mo.

Asthana, R.↗

Thermodynamic properties of some metal oxide-zirconia systems

Metal oxide-zirconia systems are a potential class of materials for use as structural materials at temperatures above 1900 K. These materials must have no destructive phase changes and low vapor pressures. Both alkaline earth oxide (MgO, CaO, SrO, and BaO)-zirconia and some rare earth oxide (Y2O3, Sc2O3, La2O3, CeO2, Sm2O3, Gd2O3, Yb2O3, Dy2O3, Ho2O3, and Er2O3)-zirconia system are examined. For each system, the phase diagram is discussed and the vapor pressure for each vapor species is calculated via a free energy minimization procedure. The available thermodynamic literature on each system is also surveyed. Some of the systems look promising for high temperature structural materials.

Jacobson, Nathan S.↗

Quantifying Losses and Assessing the Photovoltage Limits in Metal–Insulator–Semiconductor Water Splitting Systems

Metal–insulator–semiconductor (MIS) photo-electrocatalysts offer a pathway to stable and efficient solar water splitting. Initially motivated as a strategy to protect the underlying semiconductor photoabsorber from harsh operating conditions, the thickness of the insulator layer in MIS systems has recently been shown to be a critical design parameter which can be tuned to optimize the photovoltage. Here we analyze the underlying mechanism by which the thickness of the insulator layer impacts the performance of MIS photo-electrocatalysts. A concrete example of an Ir/HfO 2 /n-Si MIS system is investigated for the oxygen evolution reaction. The results of combined experiments and modeling suggest that the insulator thickness affects the photovoltage i) favorably by controlling the flux of charge carriers from the semiconductor to the metal electrocatalyst and ii) adversely by introducing nonidealities such as surface defect states which limit the generated photovoltage. It is important to quantify these different mechanisms and suggest avenues for addressing these nonidealities to enable the rational design of MIS systems that can approach the fundamental photovoltage limits. The analysis described in this contribution as well as the strategy toward optimizing the photovoltage are generalizable to other MIS systems.

36 MATERIALS SCIENCE↗

Scalable Variable Charge Molecular Dynamics Simulations of Metal-Oxide Systems

Interfaces between metals and oxides are an important feature in many technologically relevant materials, e.g., oxidation of metal surfaces, oxide-dispersion strengthened (ODS) alloys, dielectric components, and thermal barrier coatings among others. Experimental studies of such interfaces are challenging since the majority are buried within the bulk, making computational modeling an attractive alternative. Molecular dynamics (MD) simulations operate at the length scales relevant to many interface-mediated mechanisms, but the requisite interatomic potentials for metal-oxide systems require computationally expensive variable charge schemes to account for the disparate bonding types, thus often limiting their effectiveness. Here we introduce several improvements to the charge transfer interatomic potential (CTIP) model which enable greater computational efficiency for large scale MD simulations. Then, using a new CTIP parametrization for the Ni-O system, we demonstrate its capabilities to capture critical atomic scale mechanisms associated with metal-oxide interfaces. Long time scale simulations (>10 ns) are used to investigate high temperature oxidation and oxide precipitation from the melt, and large length scale simulations (> 1 million atoms) are used to study the interaction of dislocations with oxide particles. We have implemented the new CTIP model in the widely used, open-source MD code LAMMPS.

Gabriel Plummer↗

Lick optical spectra of quasar HS 1946+7658 at 10 kilometers per second resolution Lyman-alpha forest and metal absorption systems

We present optical spectra of the most luminous known quasi stellar object (QSO) HS 1946+7658 (z(sub em) = 3.051). Our spectra have both full wavelength coverage, 3240-10570 A, and in selected regions, either high signal-to-noise ratio, SNR approximately equals 40-100, or unusually high approximately 10 km/sec resolution, and in parts of the Ly alpha forest and to the red of Ly alpha emission they are among the best published. We find 113 Ly alpha systems and six metal-line systems, three of which are new. The metal systems at z(sub abs) = 2.844 and 3.050 have complex velocity structure with four and three prominent components, respectively. We find that the system at z(sub abs) = 2.844 is a damped Ly alpha absorption (DLA) system, with a neutral hydrogen column density of log N(H I) = 20.2 +/- 0.4, and it is the cause of the Lyman limit break at lambda approximately equals 3520 A. We believe that most of the H I column density in this system is in z(sub abs) = 2.8443 component which shows the strongest low-ionization absorption lines. The metal abundance in the gas phase of the system is (M/H) approximately equals -2.6 +/- 0.3, with a best estimate of (M/H) = -2.8, with ionizaion parameter log gamma = -2.75, from a photoionization model. The ratios of the logarithmic abundances of C, O, Al, and Si are all within a factor of 2 of solar, which is important for two reasons. First, we believe that the gas abundances which we measure are close to the total abundances, because the ratio of aluminum to other elements is near cosmic, and Al is a refractory element which depletes very readily like chromium, in the interstellar medium. Second, we do not see the enhancement of O with respect to C of (O/C) approximately equals 0.5-0.9 reported in three partial Lyman limit systems by Reimers et al. (1992) and Vogel & Reimers (1993); we measure (O/C) = -0.06 for observed ions and (O/C) approximately equals 0.2 after ionization corrections, which is consistent with solar abundances. We see C II*(lambda 1335) offset by 15 km/sec with respect to C II(lambda 1334), presumably because the gas density varies from 2 to 8 cm(exp -3) with changing velocity in the DLA system. These densities imply that the damped component is 6-25 pc thick, which is reasonable for a single cloud in a cold spiral disk. They also imply that the cloud is relatively highly ionized with more C III than C II, more O III than O I, and log N(H I) = 20.72, which is 3 times the H I column. The system at z(abs) = 1.7382 is also believed to be damped with N(H I) approximately equals 10(exp 21) cm(exp -2), because we see Cr II, but its Ly alpha line will never be seen because it is below the Lyman limit of the other DLA system. We see a 2.6 sigma lack of Ly alpha forest lines well away from the QSO redshift, which may be a chance fluctuation. We also see a correlation between column density N(H I) and Doppler parameter b for 96 unsaturated Ly Alpha forest absorption lines, and although this correlation persists in the 36 Ly alpha lines which lie in regions where the SNR approximately equals 8-16, we agree with Rauch et al. (1993) that it is probably a bogus effect of low supernova remnant (SNR). The same applies to lines with very low b values: in regions where SNR less than or equal to 8 we see many Ly alpha lines which appear to have 10 less than or equal to b less than or equal to 20, but when 8 less than or equal to SNR less than or equal to 16 we see only one line with b less than or equal to 15 km/sec, and two others which we believe have b less than or equal to 20, with values of 20 and 16 km/sec. Traditional Ly alpha line samples which include all lines which have W/sigma(W) greater than or equal to 4 are not adequate to explore the distribution of the properties of individual clouds, because we need much higher (W/sigma(W)) and SNR to avoid the strong biases.

Fan, Xiao-Ming↗

The Application of DFT to Systems Containing Metal Atoms

The application of density functional theory (DFT) to a series of metal containing systems will be described. The focus will be on the calculation of accurate bond energies, especially metal-ligand successive bond energies. The DFT results will be compared with experiment and other levels of theory. If time permits, metal clusters will also be discussed.

Ricca, Alessandra↗

High-energy-rate magnetohydraulic metal forming system

In the magnetohydraulic metal forming system, a sonic shock wave is generated in a liquid medium by a coil energized by an electrical discharge. These waves transfer energy from a metal diaphragm, actuated by a pulsed magnetic field, to a metal workpiece. In the development a study was made of the pressure pulse phenomenon in a liquid medium.

Source record↗

Reusable Metallic Thermal Protection Systems Development

Metallic thermal protection systems (TPS) are being developed to help meet the ambitious goals of future reusable launch vehicles. Recent metallic TPS development efforts at NASA Langley Research Center are described. Foil-gage metallic honeycomb coupons, representative of the outer surface of metallic TPS were subjected to low speed impact, hypervelocity impact, rain erosion, and subsequent arcjet exposure. TPS panels were subjected to thermal vacuum, acoustic, and hot gas flow testing. Results of the coupon and panel tests are presented. Experimental and analytical tools are being developed to characterize and improve internal insulations. Masses of metallic TPS and advanced ceramic tile and blanket TPS concepts are compared for a wide range of parameters.

Blosser, Max L.↗

Additively Manufactured Metals in Oxygen Systems Project

Metals produced by additive manufacturing methods, such as Powder Bed Fusion Technology, are now mature enough to be considered for qualification in human spaceflight oxygen systems. The mechanical properties of metals produced through AM processes are being systematically studied. However, it is unknown whether AM metals in oxygen applications may present an increased risk of flammability or ignition as compared to wrought metals of the same metallurgical composition due to increased porosity. Per NASA-STD-6001B materials to be used in oxygen system applications shall be based on flammability and combustion test data, followed by a flammability assessment. Without systematic flammability and ignition testing in oxygen there is no credible method for NASA to accurately evaluate the risk of using AM metals in oxygen systems.

Tylka, Jonathan↗

Development of techniques for processing metal-metal oxide systems

Techniques for producing model metal-metal oxide systems for the purpose of evaluating the results of processing such systems in the low-gravity environment afforded by a drop tower facility are described. Because of the lack of success in producing suitable materials samples and techniques for processing in the 3.5 seconds available, the program was discontinued.

Johnson, P. C.↗

Semi-Empirical Interatomic Potential for Large-Scale Molecular Dynamics Simulation of Metal-Oxide Systems

Classical molecular dynamics (MD) simulation can be applied to systems containing billions of atoms during times up to microseconds. However, utilization of a large-scale MD simulation requires reliable but computationally cheap interatomic potentials. In the case of metallic systems, embedded atom method (EAM) and Finnis-Sinclair (FS) potentials are the reasonable choices, but their development for multicomponent alloys is a challenge. Addition of oxygen atoms makes the problem of developing semi-empirical potentials even more difficult because the long-range Coulomb interaction cannot be neglected, and different atoms have different charges which vary during MD relaxation such that a charge equilibration procedure should be applied every MD step. As results researchers tend to avoid simulating metal-oxide systems. In this talk, a new Finnis-Sinclair (FS) Ni-Co-Cr potential will be presented. Special attention will be paid to reproducing of the element melting temperatures and clustering. Next, a charge transfer ionic potential (CTIP) developed to simulate the NiO properties will be presented. This potential utilizes the Ni FS potential and accounts for the Coulomb interaction in the vicinity of oxygen atoms. Fitting of the CTIP parameters and FS potential functions describing the interaction with oxygen atoms to the available experimental and ab initio data will be discussed. Results of MD simulation of interaction of NiO particles with dislocations in Ni will be shown.

molecular dynamics simulation↗

Dynamic Beam Shape Sensing and Control in an Open Architecture Metal AM System for Microstructure Manipulation

Most commercially available metal additive manufacturing (AM) systems are closed-architecture, meaning that the system manufacturer limits the ability of the user to directly control the process conditions and can modify the specified inputs using proprietary methods. Unfortunately, this approach severely limits or confounds the ability for users to perform research on fundamental aspects of additive manufacturing. ARCTOS Technology Solutions (ARCTOS) produces an open-architecture laser powder bed fusion (PBF) additive manufacturing system that allows the user to fully control all aspects of the process control and monitoring. The purpose of this project is to help develop beam shaping capabilities and controls within the ARCTOS open-architecture system for control of microstructure evolution during metal AM.

36 MATERIALS SCIENCE↗

Microreactor-liquid metal battery system in energy markets: An evaluation of potential costs, technology, and policy impacts

Microreactors represent an emerging innovation in the nuclear industry; yet have been overshadowed by their high capital costs. With the Inflation Reduction Act of 2022 (IRA), new opportunities have emerged to improve the economics of microreactor systems. This work examines liquid metal batteries (LMB) as a value-adding technology as part of microreactor-LMB systems within three U.S. electricity markets: ERCOT, PJM, and MISO. Our investigation considers key uncertainties: the cost of microreactors, the performance of LMBs, and the eligible tax credit levels. To this end, we use a dispatch optimization to trace not only the changes in system economics but also to provide a granular picture of energy delivery within the systems. We find that even with favorable costs for microreactors, significant regional variations in the project sizing and returns exist across the markets. Our heuristic method identifies their non-electric application potentials beyond electricity and technical requirements to maximize returns. The results suggest that 12–39 % of reactor heat could be cost-effectively diverted to produce more valuable by-products in U.S. markets. Including the impacts of tax credits, we establish the outcomes of each provision with varying rates. Coupling an LMB to a microreactor consistently improves the net present value of a microreactor compared to its standalone operation. In conclusion, for reasonable assumed conditions, we quantify a heterogeneous impact of round-trip efficiency (RTE) and extended LMB service life across the three markets—a one-year extension in LMB service life is roughly equivalent to a 2.11 % improvement in RTE for ERCOT, 1.16 % for PJM, and 1.04 % for MISO.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗

Getter Capsules for Heat-Transport Systems

Metal absorbs hydrogen dissolved in heat-transfer fluids. Blockages by hydrogen gas in refrigerators, heat pipes, and other two-phase heat-transport systems eliminated by use of degassing metals or alloys called getters. Getter contained in getter capsule placed in series or in parallel with heat-transport loop. Gas-removal technique more specific and more reliable in solving problem of gas blockage than older procedures.

Seidenberg, Benjamin↗