Search NASA⌕ Search

SEARCH · Search NASA

Results for “Microstructure characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2016

Thickness and microstructure characterization of TGO in thermal barrier coatings by 3D reconstruction

Yttria-stabilized zirconia (YSZ) thermal barrier coatings (TBCs) are prepared by plasma spraying. Thermally grown oxide (TGO) would be formed between YSZ topcoat and bond coat after 50 h thermal service for YSZ TBCs. The electron back scattered diffraction (EBSD) results reveal that the TGO layer is composed of α-Al{sub 2}O{sub 3} and cubic Al{sub 2}NiO{sub 4} layers. Measured values of TGO thickness from the 2D-SEM image are greater than or equal to its real thickness due to the fact that the TGO layer is much rolling so that up and down surfaces of the TGO can't be completely perpendicular to the cross-section direction confirmed by 3D-SEM. Furthermore, 3D-SEM results reveal that the real thickness of TGO layer is 3.10 μm instead of 7.1 μm. In addition, 3D-EBSD confirmed that α-Al{sub 2}O{sub 3} layer in TGO is composed of single layer of grains and Al{sub 2}NiO{sub 4} layer consist of multilayer of grains while α-Al{sub 2}O{sub 3} layer is mixed with single layer and multilayer of α-Al{sub 2}O{sub 3} grains from observation of the 2D-EBSD image. It provides a new method to characterize real thickness and microstructure of TGO, which is also applied to other film materials. - Highlights: •This work provides a new method to measure the real thickness of TGO. •YSZ TBCs were prepared by plasma spraying. •TGO is formed in TBCs by simulating thermal service at 1100 °C for 50 h. •Real thickness and microstructure of TGO were investigated by 3D reconstruction.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructural Characterization of High Dose Irradiated HT9

The present report provides a short summary of the recent efforts to irradiate various HT9 heats and compositions to a high damage level (>500 peak dpa) and characterize the changes to the microstructure. The majority of the data reported here will focus on characterizing the “INL” HT9 heat. This particular heat was chosen due to its high volume fraction of tempered martensite (>90%) in the microstructure. The results show that very little swelling is present in INL HT9 up to doses up to 600 peak dpa. Voids are only observed in the near surface region. Some carbides are also observed to accompany the irradiation. Comparison of void swelling with published neutron irradiation shows good agreement. Additional investigations into the response of delta ferrite grains show a very different distribution of voids and significantly higher void swelling compared to the tempered martensite grains.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2014

Microstructure characterization and mechanical behaviors of a hot forged high Nb containing PM-TiAl alloy

In this work, the effects of deformation on the microstructure and mechanical behaviors of TiAl alloy were investigated. Deformed microstructure observation was characterized by scanning electron microscopy, electron back scattered diffraction technique, transmission electron microscopy and DEFORM-3D software. Results indicated that the core area of the TiAl pancake was characterized by completely dynamically recrystallized microstructures, however some residual lamellar colonies can be observed near the edge area, which are primarily caused by a temperature drop and inhomogenous plastic flow. The main softening mechanism is dynamic recrystallization of γ grains. The as-forged alloy exhibited excellent mechanical properties at both room temperature and high temperature. Tensile test results showed that the ultimate tensile strength of the alloy increased from 832 MPa at room temperature to 853 MPa at 700 °C, while the elongation increased from 2.7% to 17.8%. Even at the temperature of 850 °C, the ultimate tensile strength maintained 404 MPa, and the elongation increased to 75%. The as-forged alloy also exhibited remarkable low-temperature superplasticity at 850 °C, with an elongation of 120%. - Highlights: • The core area of the TiAl pancake was characterized by DRX microstructure. • The elongation at RT is higher than that of other high Nb-containing TiAl alloys. • The forged alloy exhibited low-temperature superplasticity at 850 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Microstructure and water absorption of ancient concrete from Pompeii: An integrated synchrotron microtomography and neutron radiography characterization

There is renewed interest in using advanced techniques to characterize ancient Roman concrete due to its exceptional durability and low-carbon footprint. In the present work, samples were drilled from the “Hospitium” in Pompeii and were analyzed by synchrotron microtomography (μCT) and neutron radiography to study how the microstructure, including the presence of induced cracks, affects their water adsorption. The water distribution and absorptivity were quantified by neutron radiography. The 3D crack propagation, pore size distribution and orientation, tortuosity, and connectivity were analyzed from μCT results using advanced imaging methods. Porosity was also measured by mercury intrusion porosimetry (MIP) as a reference. Ductile fracture patterns were observed once cracks were introduced. Compared to Portland cement mortar/concrete, the Pompeii samples had relatively high porosity, low connectivity, and a similar coefficient of capillary penetration. In addition, permeability was predicted from models based on percolation theory and pore structure data to evaluate the fluid transport properties. Understanding the microstructure of ancient Pompeii concrete is important because it could inspire the development of modern concrete with high durability.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Microstructural Characterization of Alloy 617 Crept into the Tertiary Regime

The microstructure of Alloy 617 was characterized following creep tests interrupted at total creep strains ranging from 2-20%. A range of creep temperatures (750-1000oC) and initial creep stresses (10-145 MPa) produced creep test durations ranging from 1 to 5800 hours. Image analysis of optical photomicrographs on longitudinal sections of the gage length was used to document the fraction of creep porosity as a function of creep parameters. Creep porosity was negligible below tertiary creep strains of 10% and increased with tertiary creep strain, thereafter. For a given temperature and total creep strain, creep porosity increased with decreasing creep stress. Creep porosity increased linearly with duration of the creep experiment. TEM performed on the gage sections did not reveal significant creep cavity formation on grain boundaries at the sub-micron level. It was concluded that the onset of tertiary creep did not result from creep cavitation and more likely arose due to the formation of low energy dislocation substructures with increasing tertiary strain.

Alloy 617↗
DOE OSTI2022

Microstructural Characterization of the Second High Fluence Baffle-Former Bolt Retrieved from a Westinghouse Two-loop Downflow Type PWR

As one of the pressurized water reactor (PWR) internal components, baffle-former bolts (BFBs) are subjected to significant mechanical stress and neutron irradiation from the reactor core during the plant operation. Over the long operation period, these conditions lead to potential degradation and reduced load-carrying capacity of the bolts. In support of evaluating long-term operational performance of materials used in core internal components, the Oak Ridge National Laboratory (ORNL), through the Department of Energy (DOE), Light Water Reactor Sustainability (LWRS) Program, Materials Research Pathway (MRP) has harvested two high fluence BFBs from a commercial Westinghouse two-loop downflow type PWR. The two bolts of interest, i.e. bolts # 4412 and 4416, were withdrawn from service in 2011 as part of a preventative replacement plan. No identification of cracking or potential damage was found for these bolts during their removal in 2011. However, the bolts required a lower torque for removal from the baffle structure than the original torque specified during installation. Irradiation displacement damage levels in the bolts range from 15 to 41 displacements per atom. The goal of this project is to perform detailed microstructural and mechanical property characterization of BFBs following in-service exposures. The information from these bolts will be integral to the LWRS program initiatives in evaluating end of life microstructure and properties. Furthermore, valuable data will be obtained that can be incorporated into model predictions of long-term irradiation behavior and compared to results obtained in high flux experimental reactor conditions. In this report, we present our latest study in FY22 on microstructural characterizations of the second high fluence baffle-former bolt, i.e., bolt # 4412. Analytical electron microscopy and atom probe tomography characterization were performed. The radiation-induced defects in the material add to the large wealth of knowledge for neutron-induced defects in 304/316 grades of stainless steels, specifically for radiation-induced precipitation after high fluence commercial PWR irradiation. The main findings are summarized as follows: 1) The cavity size was considerably larger in the bolt thread section than in the bolt head, with the bolt thread section having a bimodal distribution of cavities greater than ~6 nm in diameter and less than ~3 nm in diameter. The bolt head only had the small-sized cavities. In addition, there was a denuded zone of large cavities near grain boundaries in the thread section of the bolt. 2) Radiation-induced precipitation in the BFB #4412 was highly complex, with the volume fraction, size, and number density of Ni/Si and Cu-rich precipitates depending strongly on the radiation temperature/dose. In many cases, co-precipitates of adjoined clusters were found with Ni/Si-rich precipitates sandwiched between Cu-rich clusters and Mo/Cr/P-rich clusters. 3) Solute segregation out of solution was highest for most solutes in the thread section of the bolt #4412 with the exception of Cu, which experienced more separation out of solution into Curich clusters in the bolt head section. This highlights the difference in the mechanisms for precipitation of Ni/Si clusters, which have the Ni 3 Si phase composition, and precipitation of Cu-rich clusters. 4) There appear to be multiple simultaneous influences that affect the microstructural variation along the length of the bolt that overcomes the ~2X difference in irradiation dose between the bolt head and the bolt thread. The irradiation temperature, thermal/fast neutron ratio variation, potential strain gradient, and exposure to PWR coolant water that each section of the bolt sees may have more influence on the microstructural evolution than the total irradiation dose. The bolt thread and shank, with higher temperature, higher relative fast neutron flux, higher strain, and exposure to coolant but lower dose, underwent more enhanced cavity formation, precipitation, and solute segregation than the bolt head section.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2018

Microstructural characterization and comparison of Ti-6Al-4V manufactured with different additive manufacturing processes

In this work, the microstructures of Ti-6Al-4V manufactured by different additive manufacturing (AM) processes have been characterized and compared. The microstructural features that were characterized are the α lath thickness, grain boundary α (GB-α) thickness, prior β grain size and α colony size. In addition, the microhardnesses were also measured and compared. The microstructure of shaped metal deposited (SMD) Ti-6Al-4V material showed the smallest variations in α lath size, whereas the material manufactured with laser metal wire deposition-0 (LMwD-0) showed the largest variation. The prior β grain size was found to be smaller in material manufactured with powder bed fusion (PBF) as compared with corresponding material manufactured with the directed energy deposition (DED) processes. Parallel bands were only observed in materials manufactured with DED processes while being non-present in material manufactured with PBF processes.

36 MATERIALS SCIENCE↗
NASA NTRS1998

A Novel Ultrasonic Method for Characterizing Microstructural Gradients in Tubular Structures

Ultrasonic velocity and time-of-flight (TOF) imaging that uses back surface reflections to gage volumetric material quality is highly suited for quantitative characterization of microstructural gradients including those due to pore fraction, density, fiber fraction, and chemical composition variations. However, a weakness of conventional pulse echo ultrasonic velocity and TOF imaging is that the image shows the effects of thickness as well as microstructural variations, unless the part is uniformly thick. This limits this imaging method's usefulness in practical applications. Prior studies have described a pulse echo TOF based ultrasonic imaging method that requires using a single transducer in combination with a reflector plate placed behind samples which, eliminates the effect of thickness variation in the image. In those studies, this method was successful at isolating ultrasonic variations due to material in plate like samples of silicon nitride, metal matrix composite, and polymer matrix composite. In this study, the method is engineered for inspection of more complex shaped structures- those having (hollow) tubular or curved geometry. The experimental inspection technique and results are described as applied to a polymer matrix composite "proof of concept" tube that contains machined patches of various depths and an as manufactured monolithic silicon nitride ceramic tube that might be used in "real world" applications.

Roth, Don J.↗
DOE OSTI2018

Microstructure Characterization of Fiber Laser Welds of S690QL High-Strength Steels

The use of fiber laser welding to join S690QL steels has attracted interest in the field of construction and assembly. Herein, 13-mm-thick S690QL welded joints were obtained without filler materials using the fiber laser. The as-welded microstructures and the impact energies of the joints were characterized and measured using electron microscopy in conjunction with high-resolution transmission electron images, X-ray diffraction, and impact tests. The results indicated that a single-sided welding technique could be used to join S690QL steels up to a thickness of 12 mm (fail to fuse the joint in the root) when the laser power is equal to 12 kW (scan speed 1 m/min). Double-side welding technique allows better weld penetration and better control of heat distribution. Observation of the samples showed that the fusion zone exhibited bainitic and martensitic microstructures with increased amounts of martensites (Ms) compared with the base materials. Also, the grains in the fusion zone increased in coarseness as the heat input was increased. The fusion zone exhibited increased hardness (397 HV{sub 0.2}) while exhibiting a simultaneous decrease in the impact toughness. The maximum impact energy value of 26 J was obtained from the single-side-welded sample, which is greater than those obtained from the double-side-welded samples (maximum of 18 J). Many more dislocations and plastic deformations were found in the fusion zone than the heat-affected zone in the joint, which hardened the joints and lowered the impact toughness. The microstructures characterized by FTEM–energy-dispersive X-ray spectrometer also exhibited laths of M, as well as stacking faults and dislocations featuring high-density, interfacial structure ledges that occur between the high-angle grain boundaries and the M and bainite.

36 MATERIALS SCIENCE↗
NASA NTRS2017

Microstructural Characterization and Modeling of SLM Superalloy 718

Superalloy 718 is an excellent candidate for selective laser melting (SLM) fabrication due to a combination of excellent mechanical properties and workability. Predicting and validating the microstructure of SLM-fabricated Superalloy 718 after potential post heat-treatment paths is an important step towards producing components comparable to those made using conventional methods. At present, obtaining accurate volume fraction and size measurements of gamma-double-prime, gamma-prime and delta precipitates has been challenging due to their size, low volume fractions, and similar chemistries. A technique combining high resolution distortion corrected SEM imaging and with x-ray energy dispersive spectroscopy has been developed to accurately and independently measure the size and volume fractions of the three precipitates. These results were further validated using x-ray diffraction and phase extraction methods and compared to the precipitation kinetics predicted by PANDAT and JMatPro. Discrepancies are discussed in context of materials properties, model assumptions, sampling, and experimental errors.

SEM↗
DOE OSTI2018

Microstructural Characterization of FeCrAl C26M Tubes

The present report summarizes the initial nanoindentation characterization of a FeCrAl alloy, C26M. Microstructural analysis using electron backscatter diffraction showed a highly textured system with the axial surface favoring orientations near the [110] and the longitudinal surface near the [111]. A large spread of grain sizes was observed from a few μm’s to 100 μm with an average grain size of ~70 μm. Nanoindentation with a Berkovich tip measured a similar hardness and modulus of ~4.4 GPa and ~240 GPa on the two surfaces, respectively. Mounting specimens in epoxy was found to be the cause of a lower stiffness and, consequently, a lower hardness and modulus value. Spherical nanoindentation was measured on the longitudinal surface of the tube to determine the nanoindentation modulus and nanoindentation yield strength. Using a 10 μm tip, the measured modulus was ~220 GPa and the yield strength was ~1.4 GPa. Indentation with a 100 μm tip resulted in a measured modulus value of ~220 GPa and yield strength of ~1.1 GPa. Some early characterization of the differences in spherical nanoindentation response of the axial and longitudinal surfaces showed a small difference between the two, but a more detailed analysis with a stiffer mounting configuration is needed to draw conclusions.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Report on initial development of a database of nuclear graphite characteristics based on microstructural characterization

This report outlines the current and future efforts to produce a comprehensive library of microstructures of nuclear graphite and carbon-based materials that are candidate materials for nuclear applications in the United States. This library must contain extensive characterizations of unirradiated graphite materials, a guide to some of the techniques used to characterize graphite, a compendium of characterization data of neutron-irradiated or oxidized material, and a compendium of microstructural information of carbon-based materials. These characterization efforts are being conducted at various length scales to understand these complex materials’ local structure and property relationships. Achieving this goal requires further developing or adapting advanced characterization techniques that capture graphite’s most relevant characteristics. Some of the general objectives of this project are to aid with the material selection, licensing, management, and core assessments of a graphite core by documenting the unirradiated microstructure of relevant grades or by characterizing the evolution of the microstructure under the reactor environment. Moreover, this project aims to provide additional information, guidelines for characterizing graphite, and a protocol to assess a nuclear graphite grade. This report also summarizes some of the initial results and some of the techniques commonly used to characterize nuclear graphite.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microstructural characterization of U-20Pu-10Zr-4Sb and U-20Pu-10Zr-4Sb-4Ln

Antimony is being investigated as a potential additive to metallic fuel to control fuel-cladding chemical interactions (FCCI). The most detrimental elements involved in FCCI are fission product lanthanides, leading to brittle intermetallics and low melting eutectic phases. Previous investigations of Sb as an additive focused on U-10Zr, in wt. %, as the fuel. The current investigation expands that to include Pu in the fuel. Here, two alloys, U-20Pu-10Zr-4Sb and U-20Pu-10Zr-4Sb-4Ln (wt. %, Ln=53Nd-25Ce-16Pr-6La) have been investigated using scanning electron microscopy (SEM) and transmission electron microscopy (TEM) to characterize the fuel as-cast microstructure and the microstructure after introduction of lanthanides. Sb reacts with Zr initially, forming Zr 2 Sb and Zr 5 Sb 3 , with as much as 20 at. % interstitial Pu present. In the presence of lanthanides, Sb forms Ln 4 Sb 3 with the lanthanides, containing ~14 at. % Pu. The Pu is substitutional for the lanthanides in the crystal lattice.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2019

Microstructural characterization of plutonium oxalate and oxide particles by three-dimensional focused ion beam tomography

Focused ion beam (FIB) tomography was used to characterize three-dimensional (3D) internal microstructures of plutonium oxalate and oxide particles. Sequential two-dimensional (2D) sectioning and imaging using FIB and 3D image reconstruction were used to elucidate and distinguish internal pore microstructure and distribution in plutonium oxide particles calcined from plutonium oxalate precipitates. The results show that the plutonium oxide particles have a significant increase in pore volume fraction while retaining the exterior morphological shape of the corresponding oxalate precipitates. This technique enables the examination of the internal structure of radioactive microparticles for nuclear forensics that is not available with conventional microscopy.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Microstructural Characterization of A709 Commercial Heats with Precipitation Treatment

This report discusses work conducted at Idaho National Laboratory in fiscal year 2022 associated with the precipitates in Alloy 709 (A709). The purpose of this work is to support the development of the A709 Code Cases to qualify A709 in Section III, Division 5 of the American Society of Mechanical Engineers Boiler and Pressure Vessel Code. This would permit the use of A709 for elevated-temperature nuclear construction. This work encompassed two broad goals. The first goal was to understand the microstructure of the second commercial heat of plate A709 purchased through the Advanced Reactors Technologies Program in both the solution-annealed and precipitation-treated conditions. Transmission electron microscopy was utilized to characterize these microstructures. Direct comparisons were then made between the solution-annealed and precipitation-treated conditions as well as between the first and second commercial heats of plate A709. The second goal was to understand the impact of variations in the time and temperature of the precipitation treatment on the properties of A709. The precipitation treatment temperature was varied from 750°C to 800°C for times ranging from 3 hours to 30 hours. The hardness of each precipitation treatment variation was measured. All of the precipitation treatment variations investigated besides a specimen from the second commercial heat of plate A709 precipitation treated at 800? for 9 hours met the room-temperature hardness requirement specified in ASTM A213 and SA-213 for UNS S31025. The hardness measured for the specimen from the second commercial heat of plate A709 that was precipitation treated at 800? for 9 hours is considered an outlier. The next step is to look at the extremes of the precipitation treatment variations investigated and conduct elevated-temperature mechanical testing. The purpose of this testing would be to assess if these time and temperature variations have any impact on the mechanical performance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2018

Microstructural characterization of laser metal powder deposited Alloy 718

Highlights: • In as-deposited condition γ′ and γ″ were found in the interdendritic regions. • JMatPro simulations confirmed accelerated precipitation in interdendritic regions. • Depletion of Niobium was still found in the dendritic core after heat treatment. • The depletion of Niobium were more noticeable when using a high heat input. • γ″ particles were less well-developed in the regions depleted of Niobium. - Abstract: A microstructural study of Laser Metal Powder Deposition (LMPD) of Alloy 718, using a low (40 J/mm) and high (100 J/mm) heat inputs (HIs) was performed. The microstructure was characterized in as-deposited condition as well as after a standard heat-treatment, using optical microscope (OM), scanning electron microscope (SEM) and Transmission Electron Microscope (TEM). Laves, MC-carbides, γ′ and γ″ are observed in the interdendritic areas of both conditions. However, the dendritic core only consists of γ-matrix. The high HI condition shows a slightly larger Primary Dendrite Arm Spacing (PDAS) as compared to the low HI condition. Additionally, the particle size of the Nb-rich constituents in the interdendritic regions (Laves-phase and Niobium carbide) is larger in the high HI sample. After heat-treatment, the Laves phase dissolves and is replaced by δ-phase in the interdendritic regions, while γ′, γ″ and MC-carbide remain in the interdendritic regions. However, the γ″ precipitates seems to be less developed in the dendritic core as compared to the interdendritic regions, especially in the high HI sample. This can be attributed to a heterogeneous distribution of Nb in the microstructure, with a lower Nb content in the dendritic core as compared to close to the interdendritic regions.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Microstructural Characterization of Irradiated U{sub 0.17}ZrH{sub 1.6} Using Ultrasonic Techniques

In recent years, there has been an increased level of effort to understand the changes in microstructure that occur due to irradiation of nuclear fuel. The primary driver for this increased effort is the potential for designing new fuels that are safer and more reliable, in turn enabling new and improved reactor technologies. Much of the data on microstructural change in irradiated fuels is generated through a host of post irradiation examination techniques such as optical microscopy (OM), scanning electron microscopy (SEM), and transmission electron microscopy (TEM) to determine grain structure, porosity, crack geometry, etc. in irradiated fuels. Such 'traditional' examination techniques were recently used to characterize a novel new fuel consisting of U{sub 0.17}ZrH{sub 1.6} pellets bonded to zircaloy-2 cladded with lead-bismuth eutectic before and after irradiation. In addition to the conventional suite of post-irradiation examination tools, several nondestructive interrogation techniques exist which bring the potential for in-situ assessment of microstructural changes. One such method, ultrasonic examination, was tested on each of the samples. This paper describes the results of this examination. Ultrasonic measurements have a long and successful history of use for nondestructive materials characterization, including nondestructive evaluation (NDE) of degradation and damage, microstructure characterization, and measurement of physical parameters for process control. Ultrasonic NDE is critical to the nuclear power industry's in-service inspection program for maintaining pressure boundary integrity, and is being actively investigated for PIE of fuels. Ultrasonic measurements, typically performed at 10 MHz or higher, performed post irradiation show that fuel microstructural parameters, such as porosity and grain size, can be correlated to ultrasonic velocity. The objective of this examination was to assess the feasibility of using ultrasonic measurements on irradiated fuel to determine sensitivity to microstructural changes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2014

Microstructure characterization of laser welded Ti-6Al-4V fusion zones

The as-welded microstructure of laser-welded Ti-6Al-4V is characterized as a function of CO2 key-hole mode laser welding speed. Martensitic α′ is the predominant phase, with some α and retained β. Phase transformation is affected by the cooling rate through laser welding speed. A higher welding speed of 1.6 to 2.0 m/min produced more martensite α′ and less retained β in the welds. 1.4 m/min welding speed produced small amounts of α, besides the martensite α′. A trace of δ titanium hydride phase seems to have formed in the weld fusion zone. Moiré fringes are a common feature in the TEM microstructure, due to abundance of multi-phase interfaces. Tensile twins and clusters of dislocations indicate that plastic deformation has happened in the as-welded microstructure, indicating the local stress levels to be approaching the yield stress on-cooling during laser welding.

36 MATERIALS SCIENCE↗