Search NASA⌕ Search

SEARCH · Search NASA

Results for “Model Optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS2010

Analysis of Sting Balance Calibration Data Using Optimized Regression Models

Calibration data of a wind tunnel sting balance was processed using a candidate math model search algorithm that recommends an optimized regression model for the data analysis. During the calibration the normal force and the moment at the balance moment center were selected as independent calibration variables. The sting balance itself had two moment gages. Therefore, after analyzing the connection between calibration loads and gage outputs, it was decided to choose the difference and the sum of the gage outputs as the two responses that best describe the behavior of the balance. The math model search algorithm was applied to these two responses. An optimized regression model was obtained for each response. Classical strain gage balance load transformations and the equations of the deflection of a cantilever beam under load are used to show that the search algorithm s two optimized regression models are supported by a theoretical analysis of the relationship between the applied calibration loads and the measured gage outputs. The analysis of the sting balance calibration data set is a rare example of a situation when terms of a regression model of a balance can directly be derived from first principles of physics. In addition, it is interesting to note that the search algorithm recommended the correct regression model term combinations using only a set of statistical quality metrics that were applied to the experimental data during the algorithm s term selection process.

Ulbrich, N.↗
NASA NTRS1993

Bayesian image reconstruction - The pixon and optimal image modeling

In this paper we describe the optimal image model, maximum residual likelihood method (OptMRL) for image reconstruction. OptMRL is a Bayesian image reconstruction technique for removing point-spread function blurring. OptMRL uses both a goodness-of-fit criterion (GOF) and an 'image prior', i.e., a function which quantifies the a priori probability of the image. Unlike standard maximum entropy methods, which typically reconstruct the image on the data pixel grid, OptMRL varies the image model in order to find the optimal functional basis with which to represent the image. We show how an optimal basis for image representation can be selected and in doing so, develop the concept of the 'pixon' which is a generalized image cell from which this basis is constructed. By allowing both the image and the image representation to be variable, the OptMRL method greatly increases the volume of solution space over which the image is optimized. Hence the likelihood of the final reconstructed image is greatly increased. For the goodness-of-fit criterion, OptMRL uses the maximum residual likelihood probability distribution introduced previously by Pina and Puetter (1992). This GOF probability distribution, which is based on the spatial autocorrelation of the residuals, has the advantage that it ensures spatially uncorrelated image reconstruction residuals.

Pina, R. K.↗
DOE OSTI2026

An Optimized Parameterization of Sub‐Grid Scale Advection for Convection Permitting Models

Convection‐permitting models (CPMs) explicitly resolve deep convection yet under‐resolve the organized lateral exchanges among drafts and their environment that control entrainment/detrainment, precipitation efficiency, and mesoscale structure. In this work, we introduce the Optimized Advection Scheme (OAS), which introduces a small rotation of the Cartesian frame of reference for the horizontal winds relative to other variables used in advection that induces cross‐gradient transport to mimic under‐resolved convective mixing. The rotation angle is selected to minimize the Kullback–Leibler divergence between the simulated and satellite observed precipitation intensity distributions, yielding a physically consistent perturbation that is computationally inexpensive and portable. Optimized Advection Scheme is implemented in WRF and evaluated over Amazon (April 2014). It shifts precipitation–precipitable‐water joint distributions toward lighter rain, reduces overly intense rates, and improves mesoscale convective system (MCS) lifetime and propagation. Mechanistically, the added cross‐gradient transport promotes convective detrainment and environmental mixing, which cools and moistens the mid‐troposphere, weakens downward momentum transport, alleviates excessive downwelling shortwave biases, and warms the surface temperature. The optimized rotation angle yields comparable improvements at 4‐km and 1‐km grid spacing, demonstrating resolution‐independent benefits across the CPM gray zone. By targeting the dynamical root of under‐mixed convective circulations, rather than tuning model microphysics or closures, OAS delivers robust, scale‐aware improvements in precipitation statistics, cloud vertical structure, and characteristics of MCS (MCSs), offering a practical pathway to more reliable CPM simulations for weather and climate applications.

CPM↗
NASA NTRS1977

Theoretic aspects of the identification of the parameters in the optimal control model

The identification of the parameters of the optimal control model from input-output data of the human operator is considered. Accepting the basic structure of the model as a cascade of a full-order observer and a feedback law, and suppressing the inherent optimality of the human controller, the parameters to be identified are the feedback matrix, the observer gain matrix, and the intensity matrices of the observation noise and the motor noise. The identification of the parameters is a statistical problem, because the system and output are corrupted by noise, and therefore the solution must be based on the statistics (probability density function) of the input and output data of the human operator. However, based on the statistics of the input-output data of the human operator, no distinction can be made between the observation and the motor noise, which shows that the model suffers from overparameterization.

Vanwijk, R. A.↗
NASA NTRS1977

Display analysis with the optimal control model of the human operator

Application of the optimal control model of the human operator to problems in display analysis is discussed. Those aspects of the model pertaining to the operator-display interface and to operator information processing are reviewed and discussed. The techniques are then applied to the analysis of advanced display/control systems for a Terminal Configured Vehicle. Model results are compared with those obtained in a large, fixed-base simulation.

Baron, S.↗
NASA NTRS1990

Influence of structural and aerodynamic modeling on optimization with flutter constraint

The influences of structural and aerodynamic modeling on multidisciplinary optimization in an aeroelastic environment are not well understood. Therefore, optimizations with flutter and frequency constraints were performed to investigate the effects these modeling factors have on various representative wings. To this end, the Automated Structural Optimization System (ASTROS) was used as a tool to minimize the weight of various fully built-up finite element wing models in subsonic and supersonic flow under given flutter and frequency constraints. First, the performance of the optimization module was tested against results from other codes on a straight and uniform wing widely used for optimization with flutter constraints. Then, fully built-up finite element models of various wings with different aspect ratios were investigated for the influence on the structural optimization for minimum weight of the following modeling factors: finite element selection, structural grid refinement; number of selected modes, retention of breathing modes; selection of reduced frequencies to be used in flutter analysis; aerodynamic panel size and placement; splining of the aerodynamic grid to the structural grid selection of extra points of the structural wing box for splining; and number of constraints to be retained. Knowledge of these influences as well as of the program behavior is important, since optimization can be made more efficient by the selection of reasonable initial models. Also, it was shown previously that modeling has an impact on the results of modal and aeroelastic analyses. Thus, if modeling errors can negatively affect the analyses, a minimum weight optimization can be jeopardized and result in an optimal design that is rather unreliable. In the following, selected results are presented and the influences of some modeling parameters on optimization are pointed out.

Striz, Alfred G.↗
DOE OSTI2024

Sensitivity analysis, surrogate modeling, and optimization of pebble-bed reactors considering normal and accident conditions

This research provides a valuable tool that streamlines the optimization process while significantly increasing its accuracy. This study creates a robust framework for reactor design optimization by incorporating comprehensive modeling using the Comprehensive Reactor Analysis Bundle, or BlueCRAB, within the Multiphysics Object-Oriented Simulation Environment (MOOSE). BlueCRAB is the United States Nuclear Regulatory Commission's code suite for non-light water reactor analysis and includes the Griffin, Pronghorn, and Bison applications. This not only improves the efficiency of the optimization process but also enhances the reliability of the results. Such a tool is essential for advancing the state-of-the-art in pebble-bed reactor technology and is critical for achieving the goals of Generation IV reactors, which aim for safe, sustainable, and economically viable nuclear energy solutions. This work presents and applies this workflow on pebble-bed reactors while considering both normal and off-normal conditions. A representative gas-cooled pebble-bed reactor at equilibrium core conditions serves as the nominal design specification for normal operation and is based on previous research. The depressurized loss-of-forced-cooling accident is deployed for off-normal conditions in this work. After defining design-related parameters and quantities of interest regarding reactor safety and performance, this multiphysics model is sampled using the MOOSE stochastic tools module. The result is a comprehensive dataset of configurations, enabling sensitivity analysis and the generation of surrogate models. Subsequently, the dataset and surrogate models are employed in two optimization studies aimed at maximizing fuel utilization and economic profit while adhering to safety and operational constraints. Performing the optimization process with fuel utilization as the metric leads to an improvement of approximately 10%, compared to engineering-judgment-based nominal conditions. The optimization on economic profit leads to an estimated increase of ~300 million USD over the lifetime of the reactor.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Optimization-Based Model Reduction Scheme for Renewable Energy Power Plants Using Standardized Testing Scenarios

This paper presents an optimization-based model reduction scheme for renewable energy (RE) power plants consisting of inverter-based resources (IBRs) operating in grid-following (GFL) or grid-forming (GFM) modes. More importantly, the datasets feeding the optimization-based model reduction scheme are generated and re-used through the standardized grid-interactive testing scenarios. Particularly, the proposed scheme makes use of the power plant point of common coupling (PCC) measurements of various quantities specified by standardized tests (e.g., voltage and frequency ride through) as per IEEE 2800, to estimate the parameters of the reduced-order model such that its dynamic performance aligns with the original detailed power plant model. The proposed model reduction approach does not require the parameters of individual IBRs and using standardized test data as input to the formulated optimization problem simplifies the reduced-order modelling scheme. Extensive case studies following standardized test scenarios verified the remarkable accuracy of the proposed approach.

Yallamilli, Ram S. [Purdue University]↗
NASA NTRS1984

Problems in large-scale structural optimization

A general design optimization model for large complex systems is defined. Major features of the model that challenge various optimization algorithms are discussed. Requirements of a model optimization algorithm are identified. Objectives of the study of various algorithms are defined and a basis for conducting such a study is developed. Primal as well as transformation methods are analytically studied and a unified viewpoint of various methods is presented. Several numerical examples are solved using different methods to study their performance. Conclusions drawn from the study are presented and discussed. Areas of future research in nonlinear programming as well as structural optimization are identified and discussed.

Arora, J. S.↗
NASA NTRS1981

Aircraft control-display analysis and design using the optimal control model of the human pilot

The use of the optimal control model (OCM) of the human pilot as a design tool is discussed. A novel procedure for the assignment and selection of model parameters in the absence of experimental data is proposed. A technique for partitioning a weakly coupled, multiaxis task into approximate state-uncoupled, single-axis tasks is introduced. The resulting modeling technique is utilized in the design and analysis of an aircraft flight-director system. This flight-director design technique differs from previous related work using the OCM in that considerable effort is devoted to ensuring that the OCM-designed director exhibits the desirable frequency-domain characteristics associated with experimentally verified classical designs (e.g., K/s 'effective vehicle' characteristics, noninteracting controls). The implications of the technique in the design of automatic flight control systems which employ the human pilot as a performance assessor and failure detector are briefly discussed.

Hess, R. A.↗
NASA NTRS2008

Modeling and Optimization for Morphing Wing Concept Generation II: Morphing Wing Modeling and Structural Sizing Techniques - Part 1

This report documents a series of investigations to develop an approach for structural sizing of various morphing wing concepts. For the purposes of this report, a morphing wing is one whose planform can make significant shape changes in flight - increasing wing area by 50% or more from the lowest possible area, changing sweep 30 or more, and / or increasing aspect ratio by as much as 200% from the lowest possible value. These significant changes in geometry mean that the underlying load-bearing structure changes geometry. While most finite element analysis packages provide some sort of structural optimization capability, these codes are not amenable to making significant changes in the stiffness matrix to reflect the large morphing wing planform changes. The investigations presented here use a finite element code capable of aeroelastic analysis in three different optimization approaches -a "simultaneous analysis" approach, a "sequential" approach, and an "aggregate" approach.

Skillen, Michael D.↗
NASA NTRS1972

Optimum Three Impulse Trajectory Generator with Patched Conic Trajectory Model

Optimal multi-impulse trajectories were investigated as a nominal about which asymptotic expansion was used to obtain approximations of optimal low thrust trajectories. The work consisted of the analysis and description of an optimal 3-impulse trajectory program. A patched-conic trajectory model was specifically designed for compatibility with the subsequent addition of the low thrust expansion approximation.

Payne, M. H.↗
DOE OSTI2024

Surrogate Model Guided Optimization of Expensive Black-Box Multi-Objective Problems: A Posteriori Methods

Many engineering applications require the simultaneous optimization of multiple conflicting objective functions. Often, these objective functions are evaluated using highly accurate computer simulations that are computationally too expensive to be evaluated hundreds or thousands of times during optimization. Thus, the goal is to find good approximations of the Pareto front using as few of these expensive simulations as possible. Here, we describe an optimization approach based on surrogate models and diverse sampling strategies to accelerate the search for the Pareto solutions. We use a separate surrogate model for approximating each objective function and then we use the surrogate models to inform where additional expensive simulations should be run. The surrogate models are updated in an active learning framework whenever new information from the expensive simulations becomes available. The sampling strategies aim at balancing local improvements of the approximate Pareto front and global exploration to identify the extrema and fill in large gaps of the approximate Pareto front. We demonstrate on a large set of benchmark problems the effectiveness of the method for finding good approximations of the Pareto front.

MATHEMATICS AND COMPUTING↗
DOE OSTI2026

Uncertainty quantification and reliability assessment for intermodal freight transportation

Intermodal freight optimization models support cost-effective, low-emission, and timely goods movement by coordinating trucks, rail, and barges. These models determine optimal flows, routing, and modal switches while respecting infrastructure and operational constraints. However, their real-world utility is often undermined by pervasive uncertainties-such as fluctuating transportation costs and emissions, variable terminal capacities, and uncertain freight demand-that distort key performance outcomes, including total system cost, carbon footprint, and transit time reliability. This study presents a structured framework for quantifying uncertainty in intermodal freight transportation (IFT) optimization. The framework evaluates how input uncertainty affects system performance and reliability, a critical need for ensuring that model-based decisions remain robust under real-world variability, especially amid volatile fuel prices, shifting demand, and growing disruptions. It integrates three complementary methods: (1) Sobol-based global sensitivity analysis to identify influential parameters affecting cost, emissions, and transit time, (2) Monte Carlo-based capacity perturbation analysis to assess robustness under probabilistic facility disruptions, and (3) Monte Carlo filtering with Bayesian inference to detect threshold-based performance vulnerabilities. The results highlight diesel truck unit cost as the dominant driver of variability. To improve system resilience, planners should prioritize uncertainty in fuel-related parameters when designing intermodal strategies.

Intermodal freight transportation↗
DOE OSTI2024

Component innovations for lower cost mechanical vapor compression

Despite significant capital and operating costs, mechanical vapor compression (MVC) remains the preferred technology for challenging brine concentration applications. Here, this work seeks to assess the dependence of MVC costs on feedwater salinity and desired water recovery and to quantify the value of improved component performance or reduced component costs for reducing the levelized cost of water (LCOW) of MVC. We built a cost optimization model coupling thermophysical, heat and mass transfer, and technoeconomic models to optimize and identify low cost MVC system designs as a function of feedwater salinity and water recovery. The LCOW ranges over 3.6 to 6.1 $\$$/m 3 for seawater feed salinities of 25–150 g/kg and water recoveries of 40–80 %. We then perform sensitivity analysis on parameter inputs to isolate irreducible costs and determine high value component innovation targets. The LCOW was most sensitive to evaporator material costs and performance, including the overall heat transfer coefficient in the evaporator. Process and material innovations such as polymer-composite evaporator tubes that reduce evaporator costs by 25 % without reducing heat transfer performance by more than 10 % would result in MVC cost reductions of 8 %.

42 ENGINEERING↗
NASA NTRS1985

Box truss analysis and technology development. Task 1: Mesh analysis and control

An analytical tool was developed to model, analyze and predict RF performance of box truss antennas with reflective mesh surfaces. The analysis system is unique in that it integrates custom written programs for cord tied mesh surfaces, thereby drastically reducing the cost of analysis. The analysis system is capable of determining the RF performance of antennas under any type of manufacturing or operating environment by integrating together the various disciplines of design, finite element analysis, surface best fit analysis and RF analysis. The Integrated Mesh Analysis System consists of six separate programs: The Mesh Tie System Model Generator, The Loadcase Generator, The Model Optimizer, The Model Solver, The Surface Topography Solver and The RF Performance Solver. Additionally, a study using the mesh analysis system was performed to determine the effect of on orbit calibration, i.e., surface adjustment, on a typical box truss antenna.

Bachtell, E. E.↗