Search NASA⌕ Search

SEARCH · Search NASA

Results for “NIL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Numerical analysis of soot emissions from gasoline-ethanol and gasoline-butanol blends under gasoline compression ignition conditions

In the present work, computational fluid dynamics (CFD) simulations of a single-cylinder gasoline compression ignition (GCI) engine were performed to investigate the impact of blending two biofuels, ethanol and n-butanol, with gasoline on the trade-off between combustion phasing and soot emissions under low load conditions. Here, in order to represent market gasoline (RD5-87), a four-component toluene primary reference fuel (TPRF) + ethanol (ETPRF) surrogate (with 20% ethanol by mole; E20) was formulated using a neural network based octane predictor such that the surrogate had the same ethanol content, Research Octane Number (RON) and Octane Sensitivity (S). In addition, a novel skeletal kinetic mechanism for ETPRF and TPRF + n-butanol (BTPRF) blends, incorporating polycyclic aromatic hydrocarbon (PAH) chemistry, was developed. A three-dimensional (3D) engine CFD formulation employing the skeletal mechanism, adaptive mesh refinement (AMR), finite-rate chemistry approach, and hybrid method of moments (HMOM) was adopted to capture the in-cylinder combustion phenomena and soot emissions. The engine CFD model was validated against RD5-87 experimental data for a broad range of start-of-injection (SOI) timings (-21/-27/-36/-45 crank angle degrees (CAD) after top-dead center (aTDC)), with respect to in-cylinder pressure, heat release rate, combustion phasing, and soot emissions. The closed-cycle simulation results were analyzed to elucidate the non-monotonic trend of soot emissions versus SOI timing: SOI-36 > SOI-45 > SOI-21 > SOI-27. Thereafter, the validated CFD model was employed to simulate the combustion of a gasoline-ethanol blend with 45% (by mole) ethanol (E45) and a gasoline-butanol blend with 45% (by mole) n-butanol (B45) under the same operating conditions to study the effects of fuel composition and SOI timing on combustion phasing and soot emissions. The sooting propensity followed the trend: B45 > E20 > E45 at all SOI timings. Overall, it was observed that the autoignition propensity was primarily related to fuel chemistry. On the other hand, sooting propensity showed strong coupling with both fuel chemistry and physical properties, with greater impact of fuel physical properties at advanced SOI timings.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2026

Regional inertia dynamics of U.S. interconnections: An event-based measurement approach

Power grid inertia plays a vital role in frequency stability following large disturbances, yet its distribution across the U.S. grid is highly uneven. While interconnection-wide inertia benchmarks are useful, they can mask regional variability driven by resource mix, network coupling, and geographic separation. This paper extends event-driven inertia estimation to the regional scale using field measurements from the Frequency Monitoring Network (FNET/GridEye). Starting from balancing authority and independent system operator footprints, candidate regions are refined using a composite coherency score that combines frequency-trajectory shape similarity, timing spread, and lead/lag behavior to ensure dynamic consistency. A filtered sliding difference method (FSDM) is then used to construct regional frequency trajectories, detect disturbance onset, and compute robust regional rate-of-change of frequency (RoCoF). Regional, local, and interconnection inertia are estimated by combining RoCoF with event power imbalance, and additional indicators (regional-to-system inertia ratio and inertial-support arrival time) quantify regional-to-interconnection coupling and relative regional contributions. The method is demonstrated on eleven regions across the Eastern Interconnection (EI) and the Western Electricity Coordinating Council (WECC), with the Electric Reliability Council of Texas (ERCOT) used for validation. In ERCOT, estimates compared against energy management system (EMS) values achieve a mean absolute percentage error of 17.94%. WECC exhibits consistently shorter inertial-support arrival times (0.15–0.3 s) than EI (0.7–1.1 s), highlighting contrasting coupling and disturbance-propagation behavior. Overall, the results reveal pronounced spatial heterogeneity in inertia and coupling, underscoring the value of regional monitoring for both operational decision-making and long-term system planning.

Disturbance events↗
DOE OSTI2024

The lipidomics reporting checklist a framework for transparency of lipidomic experiments and repurposing resource data

The rapid increase in lipidomic studies has led to a collaborative effort within the community to establish standards and criteria for producing, documenting, and disseminating data. Creating a dynamic checklist that condenses key information about lipidomic experiments into common terminology will enhance the field's consistency, comparability, and repeatability. Here, we describe the structure and rationale of the established Lipidomics Minimal Reporting Checklist to increase transparency in lipidomics research.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

A reduced-order model of concentration polarization in reverse osmosis systems with feed spacers

Feed spacers in reverse osmosis systems generate complex fluid flows that limit computational fluid dynamics (CFD) simulations to small length and time scales. That limits our ability to simulate mineral scaling and other membrane fouling phenomena, which occur over longer length and time scales. Thus motivated, we develop a reduced model that replaces the CFD simulation of the velocity field with an analytical model that mimics spacers. This focuses the remaining numerical effort on simulating the advection–diffusion equation governing solute transport. We motivate and validate the model with CFD simulations and bench-scale experiments of spacer filaments in three different arrangements, including cases of unsteady vortex shedding. We show that the model produces a roughly 10,000-fold speedup compared to CFD, and accurately reproduces CFD predictions of not only the average and maximum concentrations, but also the local concentration distribution along the membrane. Here, we also demonstrate the model for simulating a feed channel with a length-to-height ratio of 200. The model provides a simple testbed for exploratory studies of multispecies transport, precipitation, and membrane fouling phenomena for which simulating spacers is often prohibitive.

Computational fluid dynamics↗
DOE OSTI2021

Striking luminescence phenomena of carbon dots and their applications as a double ratiometric fluorescence probes for H2S detection

Here, we report some new observations on the luminescence of carbon dots (CDs) that are passivated with polyethylene glycol, and explored them, for the first time, as highly sensitive H2S detection probe. The as-prepared CDs have an ultraviolet (UV) emission at 350 nm and a green emission at 540 nm when excited at 270 nm, but they have only a green emission at 523 nm when excited at 365 nm. As Na2S is added to the CDs, the UV emission decreases gradually, while the green emission increases slightly, and interestingly a new emission appears at 455 nm is increased linearly in intensity with the increase of Na2S concentration. The blue emission at 455 nm is from the intrinsic core of CDs, and the green emissions at 540 or 523 nm are from their surface states, while the UV emission at 350 nm is from the anchored PEG. Both the emission intensity ratios of F-450/F-350 and F-455/F-523 show an excellent linear relationship with the Na2S concentration in the range of 0-800 mu M, and the detection limit estimated from both of them is approximately 7.0 nM, indicating our method is the most sensitive H2S CDs based detection method reported thus far. Furthermore, the detection was tested successfully for H2S imaging in live cells. We propose that the interactions of H2S with the CDs and the anchored ligands, as well as the energy transfer between the ligands and the CDs, are responsible for the luminescence responses for H2S detection. Our studies enrich the world of carbon dots with plenty of potential applications. (C) 2020 Elsevier Ltd. All rights reserved.

Bioimaging↗
DOE OSTI2021

Combustion chemistry in the twenty-first century: Developing theory-informed chemical kinetics models

Over the past 20 to 25 years theoretical chemistry (particularly theoretical chemical kinetics) has played an increasingly important role in developing chemical kinetics models for combustion. Theoretical methods of obtaining rate parameters are now competitive in accuracy with experiment, particularly for small molecules. Moreover, theoretical methods can deal with conditions that experiments frequently cannot. In addition to increased accuracy, theory has rejuvenated methods and discovered phenomena that were completely unappreciated, or at least underappreciated, in the 20th century. Our primary interest here is in molecular-level issues, i.e. in calculating rate and transport parameters. However, dealing with kinetics models that involve thousands of reactions and hundreds of species is important for practical applications and is relatively new to the 21st century. Theory, in a general sense, and theoretical methods development have a role to play here too. We discuss in this review all these topics in some detail with an emphasis on issues and methods that have emerged in the last 20 years or so. Even so, our review is selective, rather than comprehensive, out of necessity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Plasma-assisted chemical-looping combustion: Mechanistic insights into low temperature methane oxidation with CuO

The low-temperature oxidation of CH 4 by CuO in a coaxial, fixed bed, double dielectric barrier discharge (DBD) reactor was investigated with time-dependent species measurements by an electron-ionization molecular beam mass spectrometer (EI-MBMS). In the experiment, 10% methane carried by noble gasses was flown at 50 sccm through 1 g CuO dispersed in quartz wool both under plasma and non-plasma conditions, while time-dependent gas-phase species profiles were collected. Plasma conditions were explored from 300 to 600 °C while the non-plasma conditions were set from 300 to 900 °C. Mechanistic insights into the oxidation of CH 4 by CuO with plasma discharge at lower temperatures (≤ 600 °C) were obtained by quantifying the fuel oxidation, intermediate species, and CO 2 production in comparison to the non-plasma conditions. Here, we observed significant enhancement of fuel oxidation from the plasma discharge between 400 and 500 °C. The CO 2 production at 500 °C with plasma was greater than that at 700 °C without plasma, reducing fuel oxidation temperature by 200+ °C. During tests, three distinct reaction stages were observed: a gas-phase transport limited stage, a surface reaction limited kinetic stage, and an oxygen ion diffusion limited stage. It was observed that plasma greatly improved the reactivity of the second stage at low temperature. In addition, no carbon deposits were observed on the resultant particles, even under the presence of plasma. M. species such as C 4 H 2 and C 6 H 6 not previously observed or predicted in CuO/CH 4 chemical looping were observed, with some species such as CH 3 OH only becoming detectable as total flowrate was increased from 50 to 1500sccm. A non-plasma reaction pathway for CH 4 based the observed species from the MBMS spectrum and previous predictions from reactive molecular dynamics simulations was created, providing a framework from which more complex plasma CuO mechanisms can be crafted from.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

The role of radical-radical chain-propagating pathways in the phenyl + propargyl reaction

Well-skipping radical-radical reactions can provide a chain-propagating pathway for formation of polycyclic radicals implicated in soot inception. Here we use controlled pyrolysis in a microreactor to isolate and examine the role of well-skipping channels in the phenyl (C 6 H 5 ) + propargyl (C 3 H 3 ) radical-radical reaction at temperatures of 800-1600 K and pressures near 25 Torr. The temperature and concentration dependence of the closed-shell (C 9 H 8 ) and radical (C 9 H 7 ) products are observed using electron-ionization mass spectrometry. The flow in the reactor is simulated using a boundary layer model employing a chemical mechanism based on recent rate coefficient calculations. Further, comparison between simulation and experiment shows reasonable agreement, within a factor of 3, while suggesting possible improvements to the model. In contrast, eliminating the well-skipping reactions from the chemistry mechanism causes a much larger discrepancy between simulation and experiment in the temperature dependence of the radical concentration, revealing that the well-skipping pathways, especially to form indenyl radical, are significant at temperatures of 1200 K and higher. While most C 9 H 7 forms by well-skipping at 25 Torr, an additional simulation indicates that the wellskipping channels only contribute around 3% of the C 9 H x yield at atmospheric pressure, thus indicating a negligible role of the well-skipping pathways at atmospheric and higher pressures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Formation of five-membered ring structures via reactions of o -benzyne

The formation of five-membered ring structures is important for the generation of curved and bowl-shaped polycyclic aromatic hydrocarbons (PAHs) under combustion conditions. Here, we report the identification of the indenyl (C 9 H 7 ) radical – the simplest aromatic hydrocarbon radical carrying an adjacent five- and six-membered ring, as the major product of the o-benzyne (o-C 6 H 4 ) reaction with propargyl (C 3 H 3 ). Because real flames exhibit a complex chemistry, elucidation of a specific reaction is very challenging. Instead, we studied the o-C 6 H 4 + C 3 H 3 reaction in a resistively heated microtubular SiC reactor at controlled conditions of 1150 K and a pressure near 10–20 Torr. To this end, the reactants o-benzyne and propargyl were pyrolytically generated from benzoyl chloride and propargyl bromide. We identified the reactants and the indenyl radical isomer-selectively utilizing photoion mass-selected threshold photoelectron spectroscopy (ms-TPES). In conclusion, the experimentally observed predominant formation of indenyl radicals finally confirms the theoretical predictions of Matsugi and Miyoshi [Phys. Chem. Chem. Phys. 14 (2012), 9722–9728] and highlights a versatile route for the formation of five-membered rings and curved PAHs via reactions of o-benzyne that favor the formation of multiring species over aliphatically substituted aromatic species.

Molecular-weight growth↗
DOE OSTI2025

Soot formation and precursor chemistry in Counterflow flames of aviation fuel surrogates

To meet market demands, the aviation sector is interested in utilizing drop-in Synthetic Aviation Turbine Fuels (SATF), either as neat fuels or in blends with conventional Jet A. SATF currently approved in standard specifications may have lower aromatic content with significant fractions of normal, branched, and cyclo-alkanes. Fundamental studies on soot formation from aviation fuels (Jet A, SATF) and their surrogate components are essential to understand how fuel composition influences soot and soot precursor formation. Here, this study reports new measurements of polycyclic aromatic hydrocarbons (PAH) and soot in counterflow diffusion flames (CDFs) of aviation fuel surrogates. Both intrusive and non-intrusive diagnostics are employed to determine the profiles of temperature, gas phase species, PAHs (up to C16), and soot volume fraction (SVF) in CDFs of iso-octane and surrogate mixtures. These measurements shed light on the transition of soot precursors to primary soot particles. In addition to serving as a common surrogate component in Jet A surrogate mixtures, iso-octane is a template species for larger, less volatile branched alkanes found in SATF mixtures. The newly developed Lawrence Livermore National Laboratory (LLNL) PAH and soot model successfully captures temperature, precursor species, and SVF profiles for the mixtures and conditions discussed in this work. Finally, a high-fidelity surrogate for Jet A is proposed that matches targeted physical and chemical properties well, while leveraging the wide range of candidate fuel molecules available in the LLNL detailed chemical model. The proposed surrogate formulation is validated against newly acquired measurements of the surrogate and literature measurements of Jet A. These new experiments and simulations provide critical insights into the PAH and soot formation from aviation fuels. Reaction pathways which require further investigation are highlighted, such that future work may bridge the remaining quantitative gaps in predicting soot formation from aviation fuel surrogates and surrogate components.

Aviation fuels↗
DOE OSTI2021

Changes in Hydrogen Concentration and Defect State Density at the Poly-Si/SiOx/c-Si Interface Due to Firing

We determined the density of defect states of poly-Si/SiOx/c-Si junctions featuring a wet chemical interfacial oxide from lifetime measurements using the MarcoPOLO model to calculate recombination and contact resistance in poly-Si/SiOx/c-Si-junctions. In samples that did not receive any hydrogen treatment, the Dit,cSi is about 2 × 1012 cm-2 eV1 before firing and rises to 3–7 × 1012 cm2 eV1 during firing at measured peak temperatures between 620 °C and 863 °C. To address the question of why AlOx/SiNy stacks in contrast to pure SiNy layers for hydrogenation during firing provides better passivation quality, we have measured the hydrogen concentrations at the poly-Si/SiOx/c-Si interface as a function of AlOx layer thickness and compared these to J0 and calculated Dit,c-Si values. We observe an increase of the hydrogen concentration at the SiOx/c-Si interface upon firing as a function of the firing temperature that exceeds the defect concentrations at the interface several times. However, the AlOx layer thickness appears to cause an increase in hydrogen concentration at the SiOx/c-Si interface in these samples rather than exhibiting a hydrogen blocking property.

41 EE - Solar Energy Technologies Office (EE-4S)↗