Search NASA⌕ Search

SEARCH · Search NASA

Results for “Nickel alloy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS2005

Prediction of Fretting Crack Location and Orientation in a Single Crystal Nickel Alloy

Fretting is a structural damage mechanism arising between two nominally clamped surfaces subjected to an oscillatory loading. A critical location for fretting induced damage has been identified at the blade/disk and blade/damper interfaces of gas turbine engine turbomachinery and space propulsion components. The high- temperature, high-frequency loading environment seen by these components lead to severe stress gradients at the edge-of-contact that could potentially foster crack growth leading to component failure. These contact stresses drive crack nucleation in fretting and are very sensitive to the geometry of the contacting bodies, the contact loads, materials, temperature, and contact surface tribology (friction). Recently, a high-frequency, high-temperature load frame has been designed for experimentally investigating fretting damage of single crystal nickel materials employed in aircraft and spacecraft turbomachinery. A modeling method for characterizing the fretting stresses of the spherical fretting contact stress behavior in this experiment is developed and described. The calculated fretting stresses for a series of experiments are then correlated to the observed fretting damage. Results show that knowledge of the normal stresses and resolved shear stresses on each crystal plane can aid in predicting crack locations and orientations.

Matlik, J. F.↗
DOE OSTI2025

Sound velocities and thermal equation of state of fcc -iron-nickel alloys at high pressure and high temperature: Implications for the cores of Moon and several planets

Fcc-Fe-Ni alloy is believed to be the most dominant solid constitute of moderate-sized terrestrial planetary cores. Investigating the physical properties, especially the density and sound velocity of Fe-Ni alloys and comparing them with seismic observations is an indispensable approach to constructing compositional models for planetary interiors. In this study, we conducted sound velocity measurements on Fe-Ni alloys with 10 wt.% and 20 wt.% Ni up to ∼13.5 GPa and 1073 K, using the ultrasonic interferometry technique in a multi-anvil apparatus in conjunction with synchrotron radiation. By fitting the experimental data to finite strain equations, the bulk and shear moduli and their pressure and temperature derivatives are derived, yielding K S0 =145.8(14) GPa, G 0 = 73.2(7) GPa, K S0 ’ = 5.89(24), G 0 ’ = 2.89(8), (∂K S /∂T) P = -0.0181(12) GPa/K and (∂G/∂T) P = -0.0393(10) GPa/K for fcc-Fe 80 Ni 20 . An examination of the density-velocity relationship shows that compressional wave velocity is insensitive to temperature within the current pressure and temperature range, while shear wave velocity exhibits a large reduction with increasing temperature. Here, extrapolation of the sound velocities following the finite strain theories suggests that much slower Vs should be expected at pressure and temperature conditions corresponding to those of the lunar core. Possible core density and velocity profiles for other moderate planets and satellites, such as Mars, Mercury, and Ganymede are also calculated.

Equation of state↗
DOE OSTI2020

Gel‐Derived Amorphous Bismuth–Nickel Alloy Promotes Electrocatalytic Nitrogen Fixation via Optimizing Nitrogen Adsorption and Activation

Abstract To achieve the electrochemical nitrogen reduction reaction (NRR) for efficient and sustainable NH 3 production, catalysts should exhibit high selectivity and activity with optimal adsorption energy. Herein we developed a three‐dimensional (3D) amorphous BiNi alloy toward a significantly enhanced NRR compared with its crystalline and metal counterparts. Ni alloying enables the chemisorption of nitrogen and the lower free‐energy change for the *NNH formation, and the 3D alloy electrocatalyst exhibits high catalytic activity for NH 3 production with a yield rate of 17.5 μg h −1 mg cat −1 and Faradaic efficiency of 13.8 %. The enhanced electron transfer and increased electrochemical surface area were revealed in the interconnected porous scaffold, affording it sufficiently efficient and stable activity for potential practical applications. This work offers new insights into optimizing the adsorption energy of reactants and intermediates combined with tuning the crystallinity of NRR electrocatalysts.

Fang, Zhiwei↗
DOE OSTI2020

Gel-Derived Amorphous Bismuth–Nickel Alloy Promotes Electrocatalytic Nitrogen Fixation via Optimizing Nitrogen Adsorption and Activation

To achieve the electrochemical nitrogen reduction reaction (NRR) for efficient and sustainable NH 3 production, catalysts should exhibit high selectivity and activity with optimal adsorption energy. Herein we developed a three-dimensional (3D) amorphous BiNi alloy toward a significantly enhanced NRR compared with its crystalline and metal counterparts. Ni alloying enables the chemisorption of nitrogen and the lower fre-energy change for the *NNH formation, and the 3D alloy electrocatalyst exhibits high catalytic activity for NH 3 production with a yield rate of 17.5 μg h -1 mg cat -1 and Faradaic efficiency of 13.8 %. The enhanced electron transfer and increased electrochemical surface area were revealed in the interconnected porous scaffold, affording it sufficiently efficient and stable activity for potential practical applications. Furthermore, this work offers new insights into optimizing the adsorption energy of reactants and intermediates combined with tuning the crystallinity of NRR electrocatalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Computational Design of Interlayers for Thermally Stable Compositionally Graded Coatings on Nickel Alloys

To extend the service life of Ni-based superalloys, refractory metal coatings are often used. However, direct bonding between metals with dissimilar crystal structure promotes brittle intermetallic phase formation. This work presents a computational thermodynamic framework for high throughput design of functionally graded interlayers to suppress deleterious phases that may form at the interlayer. The Thermo-Calc software package was used to screen candidate metallic interlayer elements based on stability of solid-solution phases. Vanadium was identified as a promising interlayer due to its consistent suppression of intermetallic phases. Temperature-dependent phase diagram mapping between 600 and 1000 °C guided selection of a compositional pathway that significantly reduced intermetallic formation compared to directly joining the Ni-based and Nb refractory alloys. Time–temperature–transformation analysis was performed to assess whether equilibrium-predicted phases are kinetically accessible along regions of the graded path where non-solid-solution phases are not fully suppressed. The methodology was further applied to additional Ni-based alloy and coating systems, illustrating its transferability as an approach for rapid computational design of graded interlayers in dissimilar high-temperature materials.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Corrosion resistance of high nickel alloys in solar salt at 600 °C for up to 4000 h

This study focuses on the time dependent performance of the corrosion resistance of IN625, H230 and 740H alloys in the solar salt (60 wt% NaNO3, 40 wt% KNO3, at 600 °C) for up to 4000 h. Alloy IN625 showed the lowest mass change with parabolic oxidation kinetics that tends to stabilize with exposure time. Both 740H and H230 alloys deviated from the parabolic oxidation behavior beyond the 3000 h of exposure. Alloy 740H showed the highest mass loss due to the nonuniform surface oxidation and the high chromium dissolution rate. Internal oxidation was noticed with Alloy H230 due to the high tungsten concentrations.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Chromium versus Aluminum: Impact of Nickel Alloy Composition and Interfacial Kinetics on High-Temperature Passivating Oxide Formation

High-temperature corrosion resistance depends critically on the formation of a passivating surface oxide, which is highly sensitive to alloy composition and structure. Such details often elude experimental investigation, and simplified analytical models fail to provide a truly chemical view of passivating oxide evolution. Here, we explicitly compare the fundamental chemistry of Cr and Al as prototypical passivating elements in Ni alloys by directly simulating competing reaction and diffusion processes within the oxide film using kinetic Monte Carlo and density functional theory. We find that the origin and expression of passivating behavior during early-stage thermal oxidation are qualitatively different between the two alloy systems. Ni–Cr alloys feature a sudden onset of passivation associated with a sharp phase transition upon Cr enrichment that directly couples oxidation kinetics to phase transformation behavior. In contrast, Ni–Al alloys display more continuous oxide phase variation with Al enrichment, ultimately resulting in a lower composition threshold for passivation and a thinner passivating layer. In addition, we elucidate the nonobvious role of metal exchange within the alloy near the oxide boundary, which fundamentally alters film composition and passivating behavior. Furthermore, our results have key implications for engineering improved corrosion-resistant alloys, both in terms of compositional variation and processing.

Alloys↗
DOE OSTI2024

Modelling of cracking during beam oscillation laser welding of a creep-resistant nickel alloy

During high power laser welding of Inconel 740H, horizontal solidification cracks form at locations between approximately 70–80% of the weld depth. With the integration of circular beam oscillation, the laser energy density distribution and underlying thermo-mechanical conditions were altered. By coupling three-dimensional heat transfer, fluid flow, and stress modelling tools, the role that circular beam oscillation plays in the formation of the strain rates and stresses driving this cracking phenomenon was identified. While the addition of a circular oscillation pattern appeared to lower the stress levels along the solidification front, it did not eliminate the appearance of horizontal cracking. Only when the beam amplitudes reached 1.6 mm did solidification cracking disappear, but the weld depths were also significantly reduced.

Gao, Mingze↗
DOE OSTI2022

Multi material/functionally graded wire arc additive manufacturing of high strength steel valves clad with nickel alloy 625 used for oil extraction

This Phase 1 technical collaboration project (ORNL/TM-2022/2683) began on August 1st, 2020 and concluded on July 31st, 2022. The collaboration partner Schlumberger is a large business enterprise assisting oil companies to extract oil from land and subsea cost competitively and safely. It is based in Houston, Texas USA. In this work as study of additive deposition of AWS EF100S-G and AWS ERNiCrMo-3 wires via wire-arc process was conducted.

36 MATERIALS SCIENCE↗
NASA NTRS1968

Heat treatment procedure to increase ductility of degraded nickel alloy

Tests demonstrate the room temperature ductility of degraded Rene 41 can be increased to acceptable values by solution heat treatment at a temperature of 2050 degrees to 2150 degrees F /1 to 2 hours/ and cooling through a controlled temperature range followed by normal aging in air /16 hours at 1400 degrees F/.

Prager, M.↗
NASA NTRS1968

Method for removing surface-damaged layers from nickel alloys

Electrical discharge machining /EDM/ damaged layer can be effectively removed from Rene 41, Inconel 625, Inconel 718, and Monel K-500 by abrasive-grit blasting or electropolishing /at room temperature/ at a current density of 5A/inches squared in a water solution of phosphoric and sulfuric acids.

Fawley, R. W.↗
NASA NTRS1972

The role of grain size and shape in the strengthening of dispersion hardened nickel alloys

Thermomechanical processing was used to develop various microsstructures in Ni, Ni-2ThO2, Ni-20Cr, Ni-20CR-2ThO2, Ni-20Cr-10W-and Ni-20Cr-10W-2ThO2. The yield strength at 25 C increased with substructure refinement according to the Hall-Petch relation, and substructure refinement was a much more potent means of strengthening than was dispersion hardening. At elevated temperature (1093 C), the most important microstructural feature affecting strength was the grain aspect ratio (grain length, L, divided by grain width, 1. The yield strength and creep strength increased linearly with increasing L/1.

Wilcox, B. A.↗