Results for “OPTICAL REFLECTIVITY” — Page 4

DOE OSTI2024

Cooling Mixed A-Site Halide Perovskites: Impact of Temperature on Optical and Structural Properties

The widespread utilization of perovskite-based photovoltaics requires probing both the structural and optical properties under extreme operating conditions to gain a holistic understanding of the material behavior under stressors. Here, in this study, we investigate the temperature-dependent behavior of mixed A-site cation lead triiodide perovskite thin films (85% methylammonium and 15% formamidinium) in the range from 300 to 20 K. Through a combination of optical and structural techniques, we find that the tetragonal-to-orthorhombic phase transition occurs at similar to 110 K for this perovskite composition, as indicated by the change in the diffraction pattern. With decreasing temperature, the quantum yield increases with a concurrent elongation of the carrier lifetimes, indicating suppression of nonradiative recombination pathways. Interestingly, in contrast to single A-site cation perovskites, an additional optical transition appears in the absorption spectrum when the phase transition is approached, which is also reflected in the emission spectrum. We propose that the splitting of the optical absorption and emission is due to local segregation of the mixed cation perovskite during the phase transition.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Glassy carbon formation from pyrolysis of polymeric coatings on fiber-optic sensors

Deploying fiber-optic sensors in nuclear reactors requires a detailed understanding of radiation effects on the fiber materials and the transmitted signals. Previous work has shown large wavelength shifts in the reflected spectra obtained from polymer-coated fiber-optic temperature sensors exposed to high neutron fluences. The sensor drift resulting from these wavelength shifts cannot be explained by radiation effects on fused silica glass. These shifts are hypothesized to be caused by the conversion of the polymeric fiber coating to a glassy carbon via radiolysis and/or pyrolysis and subsequent radiation-induced compaction. Here, thermal degradation of these polymeric coatings was studied to provide insight into the potential origins of the sensor drift phenomenon. Acrylate- and polyimide-coated fibers were heated under various temperatures (250–1300 °C) and environments (oxidative and inert), and the resulting coating products were characterized via mass-loss data, scanning electron microscope imaging, and Raman spectroscopy. Results suggest that the polymer decomposition product of both coating types, at least under inert conditions, is indeed a glassy carbon. Analytical models that account for radiation-induced glassy carbon coating compaction show significant compressive fiber strains and predicted wavelength shifts that agree well with experimental measurements, providing additional evidence that supports the hypothesized origins of the sensor drift.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Nonthermal Plasma-Stimulated C–N Coupling from CH 4 and N 2 Depends on the Presence of Surface CH x and Plasma-Phase CN Species

Formation of C–N containing compounds from plasma-catalytic coupling of CH 4 and N 2 over various transition metals (Ni, Pd, Cu, Ag, and Au) is investigated using a multimodal spectroscopic approach, combining polarization-modulation infrared reflection–absorption spectroscopy (PM-IRAS) and optical emission spectroscopy (OES). Through sequential experiments utilizing CH 4 and N 2 nonthermal plasmas, we minimize plasma-phase reactions and identify key intermediates for C–N coupling on metal surfaces. Results show that simultaneous CH 4 and N 2 exposure with plasma stimulation produces surface C–N species. However, N 2 –CH 4 sequential exposure does not lead to C–N species formation, while CH 4 –N 2 sequential exposure reveals the presence of CH x surface species and CN radical species as key precursors to C–N species formation. From further analysis using X-ray photoelectron spectroscopy and liquid chromatography–mass spectrometry, the influence of exposure conditions on the degree of nitrogen incorporation and the nature of C–N species formed were revealed. The work highlights the importance of surface chemistry and exposure conditions in surface C–N coupling with plasma stimulation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Unraveling the Mechanism of Interfacial Charge Transfer and Photoresponsivity of WS 2 Quantum Dots/MoS 2 (0D–2D) Heterostructure-Based Transistors

To assess the efficacy of a mixed-dimensional van der Waals (vdW) heterostructure in modulating the optoelectronic responses of nanodevices, the charge transport properties of the transition-metal dichalcogenide (TMD)-based heterostructure comprising zero-dimensional (0D) WS 2 quantum dots (QDs) and two-dimensional (2D) MoS 2 flakes are critically analyzed. Herein, a facile strategy was materialized in developing an atomically thin phototransistor assembled from mechanically exfoliated MoS 2 and WS 2 QDs synthesized using a one-pot hydrothermal route. The amalgamated photodetectors exhibited a high responsivity of ∼8000 A/W at an incident power of 0.05 nW of white light, surpassing that of the pristine MoS 2 devices. Furthermore, the detectivity of pristine MoS 2 , which was on the order of 10 10 , increased to 10 12 Jones for the WS 2 QDs/MoS 2 heterostructure photodetector, outperforming other WS 2 -based materials. The quasiparticle band gap and density of states (DOS) are further analyzed to elucidate the photophysics of the WS 2 QD/MoS 2 hybrid assembly. The difference in the work function between MoS 2 and WS 2 QDs gives rise to an electric field across the 0D–2D interface, facilitating effective charge separation and migration and contributing to the enhancement of photoresponsivity. The analysis of optical responses using density functional theory (DFT) revealed stronger absorption and less reflection over a broader spectrum of wavelengths for the heterostructure compared to the pristine materials. The estimated optical conductivity aligns well with the experimentally predicted maximum photoresponsivity under visible light, which is attributed to the high absorbance of 2D MoS 2 . In conclusion, combining diverse spectroscopic and imaging techniques with quantum simulation provides insights that clarify the pertinence of 0D–2D TMDs in designing phototransistors.

WS2 QDs/MoS2 heterostructure↗

DOE OSTI2024

Acoustic and optical phonon frequencies and acoustic phonon velocities in Si-doped AlN thin films

We report the results of the study of the acoustic and optical phonons in Si-doped AlN thin films grown by metal–organic chemical vapor deposition on sapphire substrates. The Brillouin–Mandelstam and Raman light scattering spectroscopies were used to measure the acoustic and optical phonon frequencies close to the Brillouin zone center. The optical phonon frequencies reveal non-monotonic changes, reflective of the variations in the thin film strain and dislocation densities with the addition of Si dopant atoms. The acoustic phonon velocity decreases monotonically with increasing Si dopant concentration, reducing by ∼300 m/s at the doping level of 3 × 1019 cm−3. The knowledge of the acoustic phonon velocities can be used for the optimization of the ultra-wide bandgap semiconductor heterostructures and for minimizing the thermal boundary resistance of high-power devices.

Physics↗

DOE OSTI2026

High-resolution bandpass x-ray imaging with crystal reflectors: Overcoming geometric aberrations

The imaging problem of a specular reflector is revisited. Retaining terms through the second order in the reflector surface expansion, we derive the form of the aberration-limiting aperture for arbitrary magnification, assuming no bandwidth limitations. A permissible relative aperture size of the reflector is limited by a set relative aberration tolerance and scales with the tangent of the central glancing angle of incidence. These limiting aberrations become practically insignificant near backscattering. The results extend to x-ray diffracting crystals in symmetric Bragg geometry shaped as an ellipsoid of revolution. This geometry permits polychromatic imaging for hard x-rays over a bandwidth defined by the accepted range of Bragg angles, thereby suppressing aberrations of higher orders. We assess ellipsoidal crystal imagers using ray tracing simulations for two high-magnification designs with Bragg angles far from and close to backscattering. Finally, in both cases, the ellipsoidal crystals produce images of higher quality compared to those formed by equivalent toroidal crystal imagers.

Bragg reflection↗

DOE OSTI2026

Artificial Soiling Replication of Field Losses on Commercial Photovoltaic Modules

Here, this study demonstrates the capabilities of an indoor artificial soiling approach developed to closely replicate the natural, cyclic soil accumulation processes in the field-dust suspension, deposition, and sedimentation/cementation-for a subtropical climate. In this work, a near-field environment is replicated in an artificial soiling cubic chamber through controlled regulation of humidity, temperature, dust type, and dust concentration, based on site-specific historical climate data. Two different models (MA and MB) of full-size commercial photovoltaic modules from a single manufacturer, installed side by side in the mid-Atlantic United States, were retrieved and subjected to artificial soiling experiments and various characterization measurements, including short-circuit current, colorimetry, reflectance, X-ray fluorescence, laser diffraction, and optical microscopy. Both in the field and in our improved field-representative artificial soiling tests, the MA model experienced roughly twice the soiling loss as the MB model. To closely replicate the field soiling losses for a site-specific climate, it is critical to include: 1) The use of field-collected dust with identical dust chemistry and particle distribution instead of standardized ISO 12103 Arizona Road dusts, 2) the use of only a small amount of field-collected dust inside the chamber during the deposition process (e.g., 0.15 g), and 3) the preconditioning of the surface coating for the partial/full dose of UV stress as experienced in the field during sunlight exposure and the abrasion as experienced in the field during regular module cleaning activities, if/as needed. The field-representative artificial soiling method developed here could potentially be adopted for rank ordering of various antisoiling coatings developed by researchers and industry stakeholders.

14 SOLAR ENERGY↗

DOE OSTI2024

Hear It? – New Physics Calls For a Healthy Target!

Nowadays, when the attention of the physics community is drawn to muon collider prospects and neutrino projects, a target as the primary source of such exotic particles is a key component of a particle physics experiment. The extreme conditions placed on the target, though, decrease its functionality and threaten the future of high-power targetry. Subject to superb magnetic fields, extreme temperatures, and radiation damage, the target is constantly at risk of unexpected failures. The Target Health Monitor (THM) aims to enable the continuous analysis of the target state throughout the experiment. Based on the optical concept of Brewster s angle and the reflectivity variation with the compositional changes in the target material, the THM will record and evaluate the radiation-caused transmutations in the target to foresee its malfunction before it affects the experimental results. The first steps in validating our THM concept have been made this summer. Continuing reflectivity measurements of the prospective target materials, we anticipate proving the THM potential to monitor target health effectively.

Havryshchuk, Kateryna↗

DOE OSTI2024

Testing and Characterization to Develop a Mechanistic Explanation for Unsaturated Drift of Fiber Optic Sensors during High-Dose Irradiation

The primary limitation for any optical fiber-based sensor for nuclear reactor applications is radiation-induced attenuation (RIA) of the transmitted and/or reflected signals. Based on several recent studies, RIA is tolerable for some fused silica optical fibers with the proper choice of sensing wavelength and fiber dopants. For extreme temperature applications (> 1000°C), sapphire optical fibers have been proposed; however, recent optical transmission measurements performed on bulk sapphire samples showed prohibitively large RIA. For some sensors, radiation-induced dimensional changes in the fiber materials can also cause significant drift. Moreover, the drift that was observed in numerous experiments performed in the High Flux Isotope Reactor (HFIR), the Advanced Test Reactor, the Massachusetts Institute of Technology Reactor, and other international facilities far exceeded what would be expected based on compaction of fused silica glass. Clearly, additional work is needed to better understand the origins of both RIA and radiation-induced drift in both silica and sapphire optical fiber-based sensors before these sensors can be reliably deployed for nuclear applications. This work evaluated the underlying mechanisms that may be responsible for RIA and drift in silica and sapphire materials. First, detailed characterization was performed on bulk fused silica glass samples that were previously irradiated to different neutron fluences at different temperatures to better understand the structural changes that drive radiation-induced drift in the absence of coating effects that are discussed later. Results show that the non-monotonic compaction that occurs with increasing neutron fluence continues up to fast neutron fluences approaching 10 22 n/cm 2 , which has important implications for physics-based models that may be used to compensate for the sensor drift. Initial Raman spectroscopy and synchrotron x-ray diffraction provide insights into the nature of the structural changes. Next, detailed characterizations were performed on silica fibers with various coatings that were subjected to several different thermal treatments. The hypothesis is that the coatings convert to carbon-rich materials that compact under irradiation, putting a large compressive strain on the fiber. Out-of-pile testing confirms that both polyimide and acrylate fiber coatings convert to glassy carbon (GC) materials when heated under inert conditions, and the degree of order (i.e., graphitization) increases with increasing temperature. The results provide increasingly strong evidence that the combination of polymeric coatings and inert (or vacuum) conditions render fiber optic sensors susceptible to significant radiation-induced drift that would not otherwise exist in uncoated fibers. Finally, transmission electron microscopy was performed on bulk sapphire samples that were irradiated to two neutron fluences at different temperatures to gain insights into the potential mechanisms driving the prohibitive RIA at higher neutron fluences and temperatures. Contrary to previous hypotheses, results show that scattering from radiation-induced voids cannot explain the observed RIA. Similarly, models for scattering losses from dislocation loops also do not agree with the experimental results. Instead, fitting to the experimental data shows that increased absorption from aluminum vacancy centers is the most likely explanation for the the prohibitively large RIA that was observed at high irradiation temperature and dose. In addition, the voids that formed in these single-crystal samples were found to align along the basal plane (a-axis) as opposed to that seen in previous observations of c-axis alignment in polycrystalline samples, which could have important implications for anisotropic swelling and other phenomena that could affect sensor performance at high neutron fluence.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2024

Testing and Characterization to Develop a Mechanistic Explanation for Unsaturated Drift of Fiber Optic Sensors during High-Dose Irradiation

The primary limitation for any optical fiber-based sensor for nuclear reactor applications is radiation-induced attenuation (RIA) of the transmitted and/or reflected signals. Based on several recent studies, RIA is tolerable for some fused silica optical fibers with the proper choice of sensing wavelength and fiber dopants. For extreme temperature applications (> 1000°C), sapphire optical fibers have been proposed; however, recent optical transmission measurements performed on bulk sapphire samples showed prohibitively large RIA. For some sensors, radiation-induced dimensional changes in the fiber materials can also cause significant drift. Moreover, the drift that was observed in numerous experiments performed in the High Flux Isotope Reactor (HFIR), the Advanced Test Reactor, the Massachusetts Institute of Technology Reactor, and other international facilities far exceeded what would be expected based on compaction of fused silica glass. Clearly, additional work is needed to better understand the origins of both RIA and radiation-induced drift in both silica and sapphire optical fiber-based sensors before these sensors can be reliably deployed for nuclear applications. This work evaluated the underlying mechanisms that may be responsible for RIA and drift in silica and sapphire materials. First, detailed characterization was performed on bulk fused silica glass samples that were previously irradiated to different neutron fluences at different temperatures to better understand the structural changes that drive radiation-induced drift in the absence of coating effects that are discussed later. Results show that the non-monotonic compaction that occurs with increasing neutron fluence continues up to fast neutron fluences approaching 10 22 n/cm 2 , which has important implications for physics-based models that may be used to compensate for the sensor drift. Initial Raman spectroscopy and synchrotron x-ray diffraction provide insights into the nature of the structural changes. Next, detailed characterizations were performed on silica fibers with various coatings that were subjected to several different thermal treatments. The hypothesis is that the coatings convert to carbon-rich materials that compact under irradiation, putting a large compressive strain on the fiber. Out-of-pile testing confirms that both polyimide and acrylate fiber coatings convert to glassy carbon (GC) materials when heated under inert conditions, and the degree of order (i.e., graphitization) increases with increasing temperature. The results provide increasingly strong evidence that the combination of polymeric coatings and inert (or vacuum) conditions render fiber optic sensors susceptible to significant radiation-induced drift that would not otherwise exist in uncoated fibers. Finally, transmission electron microscopy was performed on bulk sapphire samples that were irradiated to two neutron fluences at different temperatures to gain insights into the potential mechanisms driving the prohibitive RIA at higher neutron fluences and temperatures. Contrary to previous hypotheses, results show that scattering from radiation-induced voids cannot explain the observed RIA. Similarly, models for scattering losses from dislocation loops also do not agree with the experimental results. Instead, fitting to the experimental data shows that increased absorption from aluminum vacancy centers is the most likely explanation for the the prohibitively large RIA that was observed at high irradiation temperature and dose. In addition, the voids that formed in these single-crystal samples were found to align along the basal plane (a-axis) as opposed to that seen in previous observations of c-axis alignment in polycrystalline samples, which could have important implications for anisotropic swelling and other phenomena that could affect sensor performance at high neutron fluence.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

DOE OSTI2024

Systems and methods for optical measurement of cross-wind

Various technologies pertaining to optical measurement of cross-wind are described herein. A beam of light is emitted along a trajectory through a shooting space from a location of a shooter to a target using a laser. The beam is reflected by the target, and the beam is received at two optical detectors. Due to changes in the index of refraction of air along the path of the beam, an envelope signal atmospherically encoded on the beam is received at each of the two apertures at different times. A signal analyzer receives a signal from each of the detectors and outputs data indicative of an average speed of the cross-wind along the trajectory in the shooting space based upon a time delay between the signals.

Bagwell, Brett↗

DOE OSTI2026

Heliostat sizing methodology for concentrating solar thermal industrial process heat projects

This study presents a method to obtain a heliostat size that minimizes the levelized cost of heat (LCOH) of a heliostat-based concentrating solar thermal system for applications of solar heating for industrial processes at operating temperatures from 565 to 1550°C. The method extends prior work by embedding a routine for system design that obtains near-optimal subsystem sizes, increasing the fidelity of drive cost functions, and adding an optical performance model to supplement the previously developed cost models, which we update to reflect current pricing trends. An illustrative business case is developed for Daggett, California, targeting specified annual thermal energy outputs of 50 to 400 GWh th . Optical performance is modeled using verified estimates from the literature. A surrogate heliostat cost model, derived from commercial heliostat designs and scaled for production volume, installation, and operations and maintenance costs, is used to develop cost functions. Results show that heliostat size strongly affects the LCOH, producing a characteristic U-shaped trend with a robust near-optimal window of 7-20 m 2 ; the heliostat size producing the lowest project cost in our study grows slightly as the project size increases, and is reduced as the operating temperature increases. The findings in this study are consistent with the general trend of smaller heliostats being deployed at existing projects for high-temperature industrial process heat and reflect the significant reduction in power electronics and other per-heliostat costs. The methodology we propose is general and can be tailored to revised cost curves as the technology continues to evolve.

14 SOLAR ENERGY↗

DOE OSTI2026

Effective medium approximation for the refractive index of stratified metal oxide composites synthesized by atomic layer deposition

Atomic layer deposition (ALD) is a unique method for synthesizing conformal layers with precise composition. It is especially useful for the synthesis of mixed metal oxides for functional materials. One application of interest is the use of ALD for tailoring the refractive index of coatings. In homogeneously distributed composites of metal oxides, the refractive properties can be approximated as the average of the indices of the components. This is known as an effective medium approximation (EMA) and can be used to design the macroscopic properties of composites. ALD produces layered, anisotropic films, so the validity of an EMA in describing these films is not clear. Here, we use optical simulations and experimental characterization of stratified composites of TiO 2 and Al 2 O 3 to study the application of an EMA to the transmission and reflection behavior of ALD-prepared mixed metal oxide thin films. We found that when the characteristic layer thickness is smaller than roughly 10 nm, the optical spectra of theoretical and experimental ALD films match the equivalent theoretical spectra for a material with a refractive index calculated from a simple, compositionally weighted EMA. Hence, this EMA could describe the transmission and reflectance spectra in ALD-derived TiO2–Al 2 O 3 nanolaminates when the films were sufficiently stratified even without thorough characterization of the real layers in the films. As a result, we demonstrated that ALD can be used to prepare effectively homogenous mixed metal oxide films with a predictable, tailorable refractive index of any value between those of the TiO 2 and Al 2 O 3 component materials.

42 ENGINEERING↗

DOE OSTI2025

Polymorphism and Phase Control in Dion–Jacobson 2D 3-(Aminomethyl)piperidinium-Based Metal Iodide Perovskites

Two-dimensional halide perovskites exhibit rich structural diversity and tunable optoelectronic properties, making them promising materials for energy, sensing, and photonic applications. In this work, we report the structural mapping of four distinct polymorphs, γ (P2 1 /c), β (P4/mbm), α (P4/mmm), and δ (Cmcm) in the two-dimensional iodoplumbate, iodostannate, and iodogermanate perovskite so-called Dion-Jacobson series (3AMP)MI4 (M = Sn, Pb, Ge), where 3AMP is 3-(aminomethyl)piperidinium. The phases exhibit systematic evolution in octahedral distortion, lattice symmetry, and metal–halide geometry, enabling structural control over optoelectronic properties. Notably, the α-phase of (3AMP)SnI 4 represents a rare, ambient-stable, high-symmetry structure for Sn-based perovskites, without a phase transition down to 100 K. Variable-temperature single-crystal diffraction, powder x-ray diffraction (PXRD), and calorimetry reveal metal- and temperature-dependent polymorph interconversions, including the emergence of long range supercell reflections in Pb-rich compositions at low temperature. Optical spectroscopy and photoelectron yield spectroscopy confirm band gap tunability and band alignment trends, highlighting symmetry-dependent shifts and anomalous band gap bowing in mixed-metal systems, verified by electronic structure calculations. Calculations additionally indicate that the higher symmetry phases have reduced electron and hole effective masses compared to the lower symmetry phases.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Dual-Image Color Normalization to Enable High-Performance Concentrating Solar Optical Metrology

Concentrating Solar Power (CSP) requires precision mirrors, and these in turn require metrology systems to measure their optical slope. In this project we studied a color-based approach to the correspondence problem, which is the association of points on an optical target with their corresponding points seen in a reflection. This is a core problem in deflectometry-based metrology, and a color solution would enable important new capabilities. We modeled color as a vector in the [R,G,B] space measured by a digital camera, and explored a dual-image approach to compensate for inevitable changes in illumination color. Through a series of experiments including color target design and dual-image setups both indoors and outdoors, we collected reference/measurement image pairs for a variety of configurations and light conditions. We then analyzed the resulting image pairs by selecting example [R,G,B] pixels in the reference image, and seeking matching [R,G,B] pixels in the measurement image. Modulating a tolerance threshold enabled us to assess both match reliability and match ambiguity, and for some configurations, orthorectification enabled us to assess match accuracy. Using direct-direct imaging, we demonstrated color correspondence achieving average match accuracy values of 0.004 h, where h is the height of the color pattern. We found that wide-area two-dimensional and linear one-dimensional color targets outperformed hybrid linear/lateral gradient targets in the cases studied. Introducing a mirror degraded performance under our current techniques, and we did not have time to evaluate whether matches could be reliably achieved despite varying light conditions. Nonetheless, our results thus far are promising.

14 SOLAR ENERGY↗

DOE OSTI2025

Models and Measurements Quantify Photon Recycling, Charge-Carrier Diffusion and Photon Scattering Contributions to Photoluminescence in InP Nanowire Arrays

Nanowire arrays present many unique advantages for solar-to-chemical energy conversion. One possible advantage is that photon recycling between neighboring nanowires has the potential to increase solar energy conversion efficiencies. Here, in this work, we explore three underlying mechanisms of optical and electronic coupling between neighboring nanowires─incident photon scattering, photon recycling, and charge-carrier transport from the photoexcited nanowire to the neighboring nanowire via the underlying substrate─using single nanowire-level microscopy and spectroscopy measurements. We present a comprehensive analysis of light absorption and emission of a single nanowire at open circuit, and subsequent re-absorption and re-emission by a neighboring nanowire. We developed a novel correlated single nanowire microspectroscopy and widefield imaging methodology to spatially resolve photon communication pathways between neighboring nanowires and selectively image re-emitted and reflected photons. We developed unique multiphysics models to couple wave optics and semiconductor photophysics to especially isolate contributions from photon recycling and electronic transport to photon emission from neighboring nanowires. By systematically varying the morphologies of the nanowires modeled, we identified pathways to maximize photon recycling between neighboring nanowires. We concluded that the measured photoluminescence is more strongly influenced by the diffusion of charge carriers as compared to photon recycling in materials with moderate-to-large charge-carrier mobilities (>10 cm 2 V –1 s –1 ), and that photon recycling dictates photoluminescence intensity only when the charge-carrier mobility is low (<1 cm 2 V –1 s –1 ). The experimental and simulation platforms developed herein for photon management strategies can be leveraged by the semiconductor photocatalysis community to enhance solar-to-chemical conversion efficiencies in semiconductor nanowire arrays.

25 ENERGY STORAGE↗

DOE OSTI2025

Chlorophyll- a dynamics in the lower Amazon River: insights from in situ and hyperspectral remote sensing using OCI-PACE

Chlorophyll-a concentration (Chla) is a key indicator of phytoplankton biomass and aquatic trophic status. However, satellite-derived Chla in sediment-rich waters, such as those found in the Lower Amazon River, remains challenging. The present study characterizes in situ Chla levels and their relationships with geographic, physical, and biogeochemical parameters in the Lower Amazon. Data collected between 2014 and 2017 across four hydrological seasons included measurements of Chla, remote sensing reflectance, and water quality parameters such as total suspended sediment, conductivity, water surface temperature, dissolved oxygen, pH, dissolved organic carbon and coloured dissolved organic matter. An empirical model was developed to estimate Chla using simulated hyperspectral bands from NASA’s PACE mission, achieving high performance (R 2 = 0.76; RMSE = 0.11 μg·L −1 ). Red bands proved particularly effective for Chla retrieval, while the addition of ultraviolet bands further enhanced model accuracy. The application of the developed model to satellite imagery yielded results consistent with in situ observations for the same hydrologic season. Seasonal variation and geographic location were major factors influencing Chla dynamics. This study provides a novel contribution to Chla estimation in optically complex, highly turbid waters and highlights the potential of the PACE mission to enhance global aquatic ecosystem monitoring. In conclusion, by offering freely available hyperspectral data with high radiometric resolution, PACE represents a significant advancement in the realm of remote sensing of aquatic environments.

Amazon River↗

DOE OSTI2025

A Machine Learning Framework for Modeling Ensemble Properties of Atomically Disordered Materials

Atomic disorder can strongly influence material properties such as charge transport, optical response, and catalytic activity. However, efficiently modeling these disorder effects remains challenging for first-principles methods due to the cost of sampling large configurational spaces and computing complex physical quantities. Recent advances of machine learning techniques, particularly graph neural networks (GNNs), has enabled the efficient and accurate predictions of complex material properties, offering promising tools for studying disordered systems. In this work, we present a general machine-learning-assisted computational framework that integrates equivariant GNNs with Monte Carlo simulations to compute the thermodynamic and ensemble-averaged functional properties of disordered materials. Using the surface-termination-disordered MXene monolayer Ti 3 C 2 T 2–x as a representative system, we find that electrical conductivity exhibits an emergent peak near the order–disorder phase transition temperature due to the interplay between electron scattering and doping. In contrast, optical conductivity remains largely insensitive to local atomic disorder and reflects the global surface chemical composition. These results highlight the role of atomic disorder in affecting material properties and demonstrate the potential of our approach for statistically modeling disorder effects in a wide range of materials such as high-entropy alloys and spin liquids.

MXene↗