Search NASA⌕ Search

SEARCH · Search NASA

Results for “ORIFICES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

A theoretical study of the acoustic impedance of orifices in the presence of a steady grazing flow

Oscillatory fluid flow in the vicinity of a circular orifice with a steady grazing flow is analyzed. A simplified system of partial differential equations is obtained by starting with the momentum and continuity equations and by assuming that the flow can be represented as an oscillatory motion superimposed on the (known) steady flow. It is found that the equations are linear in the region where grazing-flow effects dominate; a solution and the resultant orifice impedance are given for this region. It is tentatively concluded that orifice resistance is directly proportional to grazing-flow velocity and that the orifice inductive end correction is not a function of grazing flow.

Rice, E. J.↗

Flow through aligned sequential orifice type inlets

Chocked flow rate and pressure profile data were taken and studied for configurations consisting of four axially aligned, sequential orifice inlets of 0.5 length diameter ratio with separation distances of 0.66 and 32 diameters. A flow coefficient - reduced temperature plot represents the flow rate data for the two cases. At a separation distance of 32 diameters the pressure profiles dropped sharply at the entrance and partially recovered within each orifice - the exception being at low temperatures, where fluid jetting through the last orifice occurred. At a separation distance of 0.66 diameter fluid jetting was prevalent at the lower inlet temperatures. These results are in qualitative agreement with data for four axially aligned, sequential Borda inlets and for tubes with single sharp edge orifice or Borda inlets to L/D's of 105 and with a water flow visualization study.

Hendricks, R. C.↗

Influence of surface static-pressure orifices on boundary-layer transition

An investigation of the interaction of a laminar boundary layer and surface static-pressure orifices was conducted on a natural laminar flow airfoil. The effects of both favorable and adverse pressure gradients were studied at Reynolds numbers based on airfoil chord from approximately 500,000 to 6,000,000 with Mach number varying accordingly from about 0.03 to 0.42. The smaller the diameter of the orifice, the less likely it will cause premature transition. Locating the orifices in a chord-wise row aligned with the flow appears to have an additive, adverse effect on transition. Tube length-to-orifice diameter ration does not seem to have a consistent influence on transition.

Somers, D. M.↗

Orifice-induced pressure error studies in Langley 7- by 10-foot high-speed tunnel

For some time it has been known that the presence of a static pressure measuring hole will disturb the local flow field in such a way that the sensed static pressure will be in error. The results of previous studies aimed at studying the error induced by the pressure orifice were for relatively low Reynolds number flows. Because of the advent of high Reynolds number transonic wind tunnels, a study was undertaken to assess the magnitude of this error at high Reynolds numbers than previously published and to study a possible method of eliminating this pressure error. This study was conducted in the Langley 7- by 10-Foot High-Speed Tunnel on a flat plate. The model was tested at Mach numbers from 0.40 to 0.72 and at Reynolds numbers from 7.7 x 1,000,000 to 11 x 1,000,000 per meter (2.3 x 1,000,000 to 3.4 x 1,000,000 per foot), respectively. The results indicated that as orifice size increased, the pressure error also increased but that a porous metal (sintered metal) plug inserted in an orifice could greatly reduce the pressure error induced by the orifice.

Plentovich, E. B.↗

Optimization of circular orifice jets mixing into a heated cross flow in a cylindrical duct

To examine the mixing characteristics of circular jets in an axisymmetric can geometry, temperature measurements were obtained downstream of a row of cold jet injected into a heated cross stream. The objective was to obtain uniform mixing within one duct radius downstream of the leading edge of the jet orifices. An area weighted standard deviation of the mixture fraction was used to help quantify the degree of mixedness at a given plane. Non-reacting experiments were conducted to determine the influence of the number of jets on the mixedness in a cylindrical configuration. Results show that the number of orifices significantly impacts the mixing characteristics of jets injected from round hole orifices in a can geometry. Optimum mixing occurs when the mean jet trajectory aligns with the radius which divides the cross sectional area of the can into two equal parts at one mixer radius downstream of the leading edge of the orifice. The optimum number of holes at momentum-flux ratios of 25 and 52 is 10 and 15 respectively.

Kroll, J. T.↗

Optimization of circular orifice jets mixing into a heated crossflow in a cylindrical duct

To examine the mixing characteristics of circular jets in an axisymmetric can geometry, temperature measurements were obtained downstream of a row of cold jet injected into a heated cross stream. The objective was to obtain uniform mixing within one duct radius downstream of the leading edge of the jet orifices. An area weighted standard deviation of the mixture fraction was used to help quantify the degree of mixedness at a given plane. Non-reacting experiments were conducted to determine the influence of the number of jets on the mixedness in a cylindrical configuration. Results show that the number of orifices significantly impacts the mixing characteristics of jets injected from round hole orifices in a can geometry. Optimum mixing occurs when the mean jet trajectory aligns with the radius which divides the cross sectional area of the can into two equal parts at one mixer radius downstream of the leading edge of the orifice. The optimum number of holes at momentum-flux ratios of 25 and 52 is 10 and 15 respectively.

Kroll, J. T.↗

Effect of the Reversal of Air Flow upon the Discharge Coefficient of Durley Orifices

Experiments were conducted to obtain information on the relationship between the coefficients for flow in two directions through thin plate orifices at low velocities. The results indicate that the ratio of the orifice discharge coefficient from standard orifice C(sub s)(sup 1) to the discharge coefficient from the reverse flow C(sub s) is always less than unity with increasing ratio of box area to orifice area. Even for areas as low as twenty, the ratios of the coefficients are not much less than unity. It is probable, however, that when the ratio of box area is less than twenty, the ratio of discharge coefficients would be greatly reduced. Specific results are given for the case of an apparatus for the laboratory testing of superchargers.

Ware, Marsden↗

Bubble Formation from Wall Orifice in Liquid Cross-Flow Under Low Gravity

Two-phase flows present a wide variety of applications for spacecraft thermal control systems design. Bubble formation and detachment is an integral part of the two phase flow science. The objective of the present work is to experimentally investigate the effects of liquid cross-flow velocity, gas flow rate, and orifice diameter on bubble formation in a wall-bubble injection configuration. Data were taken mainly under reduced gravity conditions but some data were taken in normal gravity for comparison. The reduced gravity experiment was conducted aboard the NASA DC-9 Reduced Gravity Aircraft. The results show that the process of bubble formation and detachment depends on gravity, the orifice diameter, the gas flow rate, and the liquid cross-flow velocity. The data are analyzed based on a force balance, and two different detachment mechanisms are identified. When the gas momentum is large, the bubble detaches from the injection orifice as the gas momentum overcomes the attaching effects of liquid drag and inertia. The surface tension force is much reduced because a large part of the bubble pinning edge at the orifice is lost as the bubble axis is tilted by the liquid flow. When the gas momentum is small, the force balance in the liquid flow direction is important, and the bubble detaches when the bubble axis inclination exceeds a certain angle.

Nahra, Henry K.↗

Bubble Formation at a Submerged Orifice in Reduced Gravity

The dynamic regime of gas injection through a circular plate orifice into an ideally wetting liquid is considered, when successively detached bubbles may be regarded as separate identities. In normal gravity and at relatively low gas flow rates, a growing bubble is modeled as a spherical segment touching the orifice perimeter during the whole time of its evolution. If the flow rate exceeds a certain threshold value, another stage of the detachment process takes place in which an almost spherical gas envelope is connected with the orifice by a nearly cylindrical stem that lengthens as the bubble rises above the plate. The bubble shape resembles then that of a mushroom and the upper envelope continues to grow until the gas supply through the stem is completely cut off. Such a stage is always present under conditions of sufficiently low gravity, irrespective of the flow rate. Two major reasons make for bubble detachment: the buoyancy force and the force due to the momentum inflow into the bubble with the injected gas. The former force dominates the process at normal gravity whereas the second one plays a key role under negligible gravity conditions. It is precisely this fundamental factor that conditions the drastic influence on bubble growth and detachment that changes in gravity are able to cause. The frequency of bubble formation is proportional to and the volume of detached bubbles is independent of the gas flow rate in sufficiently low gravity, while at normal and moderately reduced gravity conditions the first variable slightly decreases and the second one almost linearly increases as the flow rate grows. Effects of other parameters, such as the orifice radius, gas and liquid densities, and surface tension are discussed.

Buyevich, Yu A.↗

Effects of Gravity on Bubble Formation at a Plate Orifice

A model of the dynamic regime of gas injection through a submerged plate orifice into an ideally wetting liquid is developed in the circumstance when successively detached bubbles may be regarded as independent objects. Two major factors favor bubble detachment: the buoyancy force and a force due to the momentum inflow into the bubble with injected gas. In normal and moderately reduced gravity, the first factor dominates. At relatively low flow rates, a growing bubble is modeled as a spherical segment touching the orifice perimeter during the whole period of its evolution till detachment. If the flow rate exceeds a critical value, another stage of bubble evolution occurs in which an almost spherical gas envelope is connected with the orifice by a nearly cylindrical gaseous stem that lengthens as the bubble rises above the plate. The bubble continues to grow until the gas supply through the stem is completely cut off, after which back flow of gas into the stem from the bubble becomes possible. In microgravity, the second factor prevails, and the latter stage is always present irrespective of the flow rate. However, the gas envelope rises and the stem lengthens very slowly. This difference in the underlying physical mechanisms provides for key properties of bubble growth and detachment being drastically different in appreciable and sufficiently reduced gravity. The frequency of bubble formation slightly decreases with and the detachment volume is almost proportional to the gas flow rate in the first case, in accordance with familiar relations. In the second case, the first variable is proportional to the flow rate whereas the second one is independent of it. Effects of other parameters, such as the orifice radius, gas and liquid densities, and surface tension are discussed.

Webbon, Bruce W.↗

An Experimental Study Synthetic Jets from Rectangular Orifices

Results of an experimental investigation on isolated synthetic jets in crossflow from rectangular orifices of different aspect ratio and orientation are presented. Three aspect ratios, AR = 4, 8, and 16, with pitch a = 90deg., were investigated, Additionally, the AR = 8 case was pitched at 20 deg.. The yaw angle, , was varied through 0 deg., 10 deg., 45 deg. and 90 deg.. All orifices had same exit area and the data were compared with synthetic as well as steady jet from a circular orifice of same area. Hotwire measurements were performed to obtain all three components of mean velocity and turbulent stresses. Data were acquired for momentum-flux ratio up to J = 50. Distributions of time- and phase-averaged data were obtained on the cross sectional plane at x/D = 0.5, 5 and 10, as well as on the axial plane of the symmetry. Qualitative flowfield similarity between synthetic and steady jets is observed. However, high-momentum 'cap' above the low-momentum 'dome', characteristic of steady jets, does not necessarily appear in the synthetic jet. The position and shape of the high-momentum region depend on the distance from the orifice, pitch, yaw as well as momentum-flux ratio. Consequently, the location of the minimum velocity in the 'dome' measured at the plane of symmetry, y(submin), is adopted as a reference for penetration estimate and trajectory comparison. For AR = 16, the dome is the largest in area with maximum velocity deficit. However, the penetration is somewhat higher for AR = 4. Increase in yaw reduces the spatial extent of the dome and the penetration height but augments the velocity deficit. At low J the dome is connected to the boundary layer and traces of the cap of high momentum fluid are visible above it. Increase in J lifts the dome and reorganizes the high-momentum fluid around its perimeter, eventually bringing it underneath. Phase-averaged data document dynamic topological changes within the cycle. Phase-averaged streamwise velocity contours on the cross-sectional plane exhibit behavior commensurate with that seen in time-averaged data at various J.

Milanovic, Ivana M.↗

Experimental Investigation of Cavitation Induced Feedline Instability from an Orifice

This paper details the results of an experimental investigation into the cavitation instabilities created by a circular orifice conducted at the University of Alabama in Huntsville Propulsion Research Center. This experiment was conducted in concert with a computational simulation to serve as a reference point for the simulation. Testing was conducted using liquid nitrogen as a cryogenic propellant simulant. A 1.06 cm diameter thin orifice with a rounded inlet was tested in an approximately 1.25 kg/s flow with inlet pressures ranging from 504.1 kPa to 829.3 kPa. Pressure fluctuations generated by the orifice were measured using a high frequency pressure sensor located 0.64 tube diameters downstream of the orifice. Fast Fourier Transforms were performed on the high frequency data to determine the instability frequency. Shedding resulted in a primary frequency with a cavitation related subharmonic frequency. For this experiment, the cavitation instability ranged from 153 Hz to 275 Hz. Additionally, the strength of the cavitation occur red as a function of cavitation number. At lower cavitation numbers, the strength of the cavitation instability ranged from 2.4 % to 7 % of the inlet pressure. However, at higher cavitation numbers, the strength of the cavitation instability ranged from 0.6 % to 1 % of the inlet pressure.

Hitt, Matthew A.↗

Mass flow rate measurements in gas-liquid flows by means of a venturi or orifice plate coupled to a void fraction sensor

Two-phase flow measurements were carried out using a resistive void fraction meter coupled to a venturi or orifice plate. The measurement system used to estimate the liquid and gas mass flow rates was evaluated using an air-water experimental facility. Experiments included upward vertical and horizontal flow, annular, bubbly, churn and slug patterns, void fraction ranging from 2% to 85%, water flow rate up to 4000 kg/h, air flow rate up to 50 kg/h, and quality up to almost 10%. The fractional root mean square (RMS) deviation of the two-phase mass flow rate in upward vertical flow through a venturi plate is 6.8% using the correlation of Chisholm (D. Chisholm, Pressure gradients during the flow of incompressible two-phase mixtures through pipes, venturis and orifice plates, British Chemical Engineering 12 (9) (1967) 454-457). For the orifice plate, the RMS deviation of the vertical flow is 5.5% using the correlation of Zhang et al. (H.J. Zhang, W.T. Yue, Z.Y. Huang, Investigation of oil-air two-phase mass flow rate measurement using venturi and void fraction sensor, Journal of Zhejiang University Science 6A (6) (2005) 601-606). The results show that the flow direction has no significant influence on the meters in relation to the pressure drop in the experimental operation range. Quality and slip ratio analyses were also performed. The results show a mean slip ratio lower than 1.1, when bubbly and slug flow patterns are encountered for mean void fractions lower than 70%. (author)

42 ENGINEERING↗

Creating Small Gas Bubbles in Flowing Mercury Using Turbulence at an Orifice

Pressure waves created in liquid mercury pulsed spallation targets have been shown to create cavitation damage to the target container. One way to mitigate such damage would be to absorb the pressure pulse energy into a dispersed population of small bubbles, however, creating such a population in mercury is difficult due to the high surface tension and particularly the non-wetting behavior of mercury on gas-injection hardware. If the larger injected gas bubbles can be broken down into small bubbles after they are introduced to the flow, then the material interface problem is avoided. Research at the Oak Ridge National Labarotory is underway to develop a technique that has shown potential to provide an adequate population of small-enough bubbles to a flowing spallation target. This technique involves gas injection at an orifice of a geometry that is optimized to the turbulence intensity and pressure distribution of the flow, while avoiding coalescence of gas at injection sites. The most successful geometry thus far can be described as a square-toothed orifice having a 2.5 bar pressure drop in the nominal flow of 12 L/s for one of the target inlet legs. High-speed video and high-resolution photography have been used to quantify the bubble population on the surface of the mercury downstream of the gas injection sight. Also, computational fluid dynamics has been used to optimize the dimensions of the toothed orifice based on a RANS computed mean flow including turbulent energies such that the turbulent dissipation and pressure field are best suited for turbulent break-up of the gas bubbles.

43 PARTICLE ACCELERATORS↗

Characterization of Gatewell Orifice Lighting at the Bonneville Dam Second Powerhouse and Compendium of Research on Light Guidance with Juvenile Salmonids

The goal of the study described in this report is to provide U.S. Army Corps of Engineers (USACE) biologists and engineers with general design guidelines for using artificial lighting to enhance the passage of juvenile salmonids into the collection channel at the Bonneville Dam second powerhouse (B2). During fall 2007, Pacific Northwest National Laboratory (PNNL) researchers measured light levels in the field at one powerhouse orifice through which fish must pass to reach the collection channel. Two light types were evaluated—light-emitting diode (LED) lights and halogen spot lights. Additional measurements with mercury lamps were made at the PNNL Aquatic Research Laboratory to determine baseline intensity of the current lighting. A separate chapter synthesizes the relevant literature related to light and fish guidance for both field and laboratory studies. PNNL will also review the Corps plans for existing lighting protocol at all of the Portland District projects and help develop a uniform lighting scheme which could be implemented. The specific objectives for this study are to 1. Create a synthesis report of existing lighting data for juvenile salmonid attraction and deterrence and how the data are used at fish bypass facilities. 2. Evaluate current B2 orifice lighting conditions with both LED and halogen sources. 3. Make recommendations as to what lighting intensity, source, and configuration would improve passage at the B2 orifices. 4. Review USACE plans for retrofit of existing systems (to be assessed at a later date).

13 HYDRO ENERGY↗

Effect of nonsymmetrical flow resistance upon orifice impedance resistance

A nonreactive orifice in an infinite baffle is analyzed. The pressure difference delta across the orifice varies sinusoidally with amplitude 1.0 and average value -P. The orifice resistance, delta p is discontinuous at zero velocity and exhibits the constant values R sub + and R sub - for u 0 and u 0, respectively. The resultant velocity has power in all harmonics of the excitation frequency. A quasi-linear resistance is defined and found to be relatively insensitive to the presence or absence of a resonant backing cavity; however, it does vary from 1.33 R sub + to 0.67 R sub + for a resistance ratio R sub +/R sub - between 0.5 and 2.0.

Posey, J. W.↗

Visual study of the effect of grazing flow on the oscillatory flow in a resonator orifice

Grazing flow and oscillatory flow in an orifice were studied in a plexiglass flow channel with a single side branch Helmholtz resonator using water as the fluid medium. An oscillatory flow was applied to the resonatory cavity, and color dyes were injected in both the orifice and the grazing flow field to record the motion of the fluid. The flow regimes associated with linear and nonlinear (high sound pressure level) impedances with and without grazing flows were recorded by a high-speed motion-picture camera. Appreciable differences in the oscillatory flow field were seen in the various flow regimes. With high grazing flows, the outflow and inflow from the resonator cavity are found to be asymmetric. The visual study confirms that jet energy loss during flow into a resonator cavity is much larger than the loss for ejection from the cavity into the grazing flow. For inflow into the resonator cavity, the effective orifice area was significantly reduced.

Baumeister, K. J.↗

Effect of grazing flow on the acoustic impedance of interacting cavity-backed orifices

The two-microphone method was used to investigate the impedance of interacting cavity-backed orifices in the presence of a grazing flow; the investigation has relevance for the control of turbomachinery noise generated within jet engines. The number (varied from one to 16), the diameter, and the spacing of the orifices were the chief parameters studied in the experimental program. It was found that interactions between adjacent orifices, while increasing reactance, do not significantly alter resistance. In addition, the grazing flow appears to reduce the rate of increase of the reactance.

Hersh, A. S.↗