Search NASA⌕ Search

SEARCH · Search NASA

Results for “OXIDE FILM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

Simultaneous Use Of Zr And Mg Anodes In XPS

Improved x-ray source for x-ray photoelectron spectroscopy (XPS) contains both zirconium anode with beryllium window and magnesium anode with aluminum window. Previously unresolvable peaks of electron-energy spectrum become resolvable. Developed specifically for use in analyzing distributions of chemical constituents in surface layers of specimens of 2219 aluminum alloy and in determining the depths of surface oxide layers and relative proportions of aluminum and oxide in layers. Also used to study chemical constituents of surface layers in other material systems - for example, thin oxide films on silicon-based semiconductor devices, oxide films on alloys, and surface layers affecting adhesion of paints or bonding materials.

Allgeyer, D. F.↗
NASA NTRS1975

Fretting of titanium at temperatures to 650 C in air

Fretting wear experiments were conducted on high-purity titanium at temperatures up to 650 C. Results indicate that up to about 500 C, the fretting wear increases with temperature. A further increase in the temperature up to 650 C results in decreasing fretting wear. This change in trend of fretting wear with temperature is shown to be associated with a change in oxidation rate. Additional experiments at 650 C showed a transmission from a low rate of fretting wear to a higher rate occurred after exposure to a number of fretting cycles; the number of cycles required to cause this transition was dependent on the normal load. Scanning electron microscopy studies revealed that this transition was marked by cracking and disruption of the surface oxide film. A model was proposed that coupled the oxidation rate kinetics of titanium at 650 C with the occurrence of wear at the surface of the oxide film.

Bill, R. C.↗
NASA NTRS1985

Oxidation protection coatings for polymers

A polymeric substrate is coated with a metal oxide film to provide oxidation protection in low Earth orbital environments. The film contains about 4 volume percent polymer to provide flexibility. A coil of polymer material moves through an ion beam as it is fed between reels. The ion beam first cleans the polymer material surface and then sputters the film material from a target onto this surface.

Mirtich, M. J.↗
NASA NTRS1986

Apparatus for producing oxidation protection coatings for polymers

A polymeric substrate is coated with a metal oxide film to provide oxidation protection in low Earth orbital environments. The film contains about 4 volume percent polymer to provide flexibility. A coil of polymer materials moves through an ion beam as it is fed between reels. The ion beam first cleans the polymer material surface and then sputters the film material from a target onto this surface.

Mirtich, M. J.↗
NASA NTRS1987

Oxidation protection coatings for polymers

A polymeric substrate is coated with a metal oxide film to provide oxidation protection in low Earth orbital environments. The film contains about four volume percent polymer to provide flexibility.

Sovey, James S.↗
NASA NTRS1974

Testing for hydrogen environment embrittlement - Primary and secondary influences

A somewhat phenomological overview of the hydrogen embrittlement process, both internal as well as external, is presented in a effort to make more clear the type of parameters which must be considered in the selection of a test method and test procedure so that the resulting data may be meaningfully applied to real engineering structures. What are believed to be the three primary influences on the embrittlement process are considered - the original location and form of the hydrogen, the transport reactions involved in the transport of hydrogen from its origin to some point it can interact with the metal to cause embrittlement, and the embrittlement interaction itself. Additionally, a few of the large number of secondary influences on the embrittlement process are discussed, for example, the influence of impurity species in the environment, surface hydride films, and surface oxide films.

Nelson, H. G.↗
NASA NTRS1977

The nature of surfaces and their influence in wear mechanisms

The wear of materials is strongly dependent upon the nature of the solid surfaces in contact, their properties and the nature of the films on them. Oxide films, orientation, crystal transformations, adhesive binding, crystal structure, hardness and the presence of alloying agents are all shown to effect one or more of the forms of wear. The three most common forms of wear, adhesive, abrasive, and corrosive, are discussed in terms of the way each is affected by various material properties. Results presented indicate how wear can be optimized by concern for properties of materials.

Buckley, D. H.↗
NASA NTRS1984

Thermal oxidation of 3C silicon carbide single-crystal layers on silicon

Thermal oxidation of thick single-crystal 3C SiC layers on silicon substrates was studied. The oxidations were conducted in a wet O2 atmosphere at temperatures from 1000 to 1250 C for times from 0.1 to 50 h. Ellipsometry was used to determine the thickness and index of refraction of the oxide films. Auger analysis showed them to be homogeneous with near stoichiometric composition. The oxide growth followed a linear parabolic relationship with time. Activation energy of the parabolic rate constant was found to be 50 kcal/mole, while the linear rate constant was 74 kcal/mole. The latter value corresponds approximately to the energy required to break a Si-C bond. Electrical measurements show an effective density of 4-6 x 10 to the 11th per sq cm for fixed oxide charges at the oxide-carbide interface, and the dielectric strength of the oxide film is aproximately 6 x 10 to the 6th V/cm.

Fung, C. D.↗
NASA NTRS1981

Reduced hydrogen permeability at high temperatures

CO and CO2 reduce hydrogen loss through iron, nickel, and cobalt based alloy tubes. Method is based on concept that oxide film on metal surface reduces hydrogen permeability through metal; adding CO or CO2 forms oxide films continuously during operation, and hydrogen containment is improved. Innovation enhances prospects for Stirling engine system utilization.

Stephens, J. R.↗
NASA NTRS1976

Efficient photovoltaic heterojunctions of indium tin oxides on silicon

Heterojunction diodes of indium tin oxide films sputtered on to p-silicon using ion-beam techniques display significant photovoltaic effects when exposed to sunlight. Galvanomagnetic and optical measurements confirm that the oxide films are highly degenerate transparent semiconductors. At a tin oxide concentration of 10%, an open-circuit voltage of 0.51 V was observed along with a short-circuit current of 32 mA/sq cm, a fill factor of 0.70, and a conversion efficiency of 12%. As the concentration was raised to 70%, the voltage remained steady, the current fell to 27 mA/sq cm, and the fill factor fell to 0.60

Dubow, J. B.↗
NASA NTRS1988

Experimental results on atomic oxygen corrosion of silver

The results of an experimental study of the reaction kinetics of silver with atomic oxygen in 10 degree increments over the temperature range of 0 to 70 C is reported. The silver specimens, of the order of 10,000 A in thickness, were prepared by thermal evaporation onto 3 inch diameter polished silicon wafers. There were later sliced into pieces having surface areas of the order of 1/4 to 1/2 square inch. Atomic oxygen was generated by a gas discharge in a commercial plasmod asher operating in the megahertz frequency range. The sample temperature within the chamber was controlled by means of a thermoelectric unit. Exposure of the silver specimens to atomic oxygen was incremental, with oxide film thickness measurements being carried out between exposures by means of an automated ellipsometer. For the early growth phase, the data can be described satisfactorily by a logarithmic growth law: the oxide film thickness increases as the logarithm of the exposure time. Furthermore, the oxidation process is thermally activated, the rate increasing with increasing temperature. However, the empirical activation energy parameter deduced from Arrhenius plots is quite low, being of the order of 0.1 eV.

Fromhold, Albert T.↗
NASA NTRS1980

Double metalization for VLSI

Postsintering process increases yield of double-layer metal conductors to almost 100 percent. When wafers containing double-metalized chips are sintered, metal layers react with oxide film remaining in insulation layer holes, breaking it up so that it no longer impedes electric current. Cooling also mechanically disrupts oxide film.

Trotter, J. D.↗
NASA NTRS2001

Study of Electrical Contacts and Devices in Advanced Semiconductors

Research conducted at Tuskegee University concentrates on electrical contacts to GaN films and their characterization with the objective of understanding contact formation and realizing low-resistance metal contacts. Contact properties are known to be strongly related to surface preparation. It appears that the as-received material had a thin oxide film on the surface of the GaN film. Various cleaning treatments were employed in order to render the surface contamination free and removal of the oxide film. Metal films were then deposited by e-beam evaporation. Electrical characteristics of these contacts indicated that the optimal treatment was an organic solvent cleaning followed by etching in buffered oxide solution. Contacts established with Al were observed to be ohmic in nature, whereas Au, Cr, Ti, and Pt exhibit rectifying contacts. Platinum contacts were almost ideal as shown by an ideality factor of 1.02.

Hall, H. P.↗
NASA NTRS1985

Float Zone Experiments in Space

The objective of this work has been to evaluate whether or not Marangoni flow could be suppressed in molten metals by the presence of very thin oxide films. Experimental work has been carried out on molten Sn under UHV conditions. A disk floating zone arrangement was developed to allow in situ Auger examination of molten surfaces. An electron energy loss technique was developed which allows detection of continuous tin oxide films of 6 A or greater. Experiments were planned to detect the effects of oxide formation upon Marangoni flow by measuring: (1) temperature profiles, (2) solid liquid interface shapes, (3) macrosegregation, and (4) the onset of oscillatory Marangoni flow by detecting oscillating temperature variations. Work on (4) showed that oscillatory temperature variations of frequency or = 10 Hz were not present in the disk float zone geometry under conditions of Ma = 4300 with an oxide free molten surface. The disk float zone geometry was modeled with a finite element analysis and temperature and velocity profiles were determined.

Verhoeven, J. D.↗
NASA NTRS1972

Fretting of Secondary-Seal-Ring Candidate Materials in Air at Temperatures to 816 C

Superalloys containing chromium showed decreasing fretting damage with increasing temperature of 816 C. This trend was related to the ability of the alloys to generate self-protecting oxide films. The damage at 816 C was one-third to one-tenth of that at 23 C. Osmium, chromium, and chromium carbide platings were fretted at 23 and 450 C. Osmium was extremely protective at 23 C but oxidized excessively at 450 C. Chromium and chromium carbide gave about the same protection at 450 C as the oxide films that formed on the superalloys. High graphite and low graphite carbons were fretted at 23 and 327 C. High graphite carbon was superior at 327 C, but low graphite carbon was the best material examined at 23 C.

Bill, R. C.↗