SEARCH · Search NASA

Results for “PLA”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

All sources NASA NTRS DOE OSTI

NASA NTRS2026

Influence of Processing Parameters on the Mechanical Properties of 3D Printed Borosilicate Particulate Reinforced Polymer Composites

Emerging composite materials are expanding the potential of additive manufacturing and enabling applications previously restricted by traditional manufacturing methods. The multi-phase nature of these composite materials combined with the complex in-ternal geometry of additively manufactured parts have enabled unique behavior, and potentially new applications. Additionally, these materials can be pyrolyzed to create dense metal, ceramic, and glass parts with geometries typically not achievable by tra-ditional processes. Additive manufacturing of borosilicate glass-based systems can open new applications in nuclear engineering, astronomy, and bone regrowth therapy. To elucidate the process-parameter relationship of borosilicate-polylactic acid (PLA) composites, mechanical testing was conducted and compared with a pure polylactic acid polymer baseline. Test specimens were fabricated by fused-filament fabrication with minimal post-processing. Yield strength, ultimate strength, and elastic modulus were calculated from stress-strain curves. Optical and scanning electron microscopy were conducted to observe the specimen microstructure before and after testing. The highest compressive yield strength for the composite was 28.22 MPa, and the highest compressive yield strength for PLA was 49.30 MPa. Print orientation was found to benefit the composite material but have a detrimental effect on the pure matrix material. An elastic modulus of 2.66 GPa was recorded for the borosilicate-PLA composite at 100% infill, 1 shell wall, and layer lines parallel to compression axis. Microscopy revealed that lower modulus composite specimens had the particulates re-distributed within the matrix. Tensile testing was done according to a polymer testing standard, which caused difficulties obtaining consistent fracture within the gauge length.

mechanical testing↗

DOE OSTI2020

Surface-modified and oven-dried microfibrillated cellulose reinforced biocomposites: Cellulose network enabled high performance

Microfibrillated cellulose (MFC) is widely used as a reinforcement filler for biocomposites due to its unique properties. However, the challenge of drying MFC and the incompatibility between nanocellulose and polymer matrix still limits the mechanical performance of MFC-reinforced biocomposites. In this study, we used a water-based transesterification reaction to functionalize MFC and explored the capability of oven-dried MFC as a reinforcement filler for polylactic acid (PLA). Remarkably, this oven-dried, vinyl laurate–modified MFC improved the tensile strength by 38 % and Young’s modulus by 71 % compared with neat PLA. Our results suggested improved compatibility and dispersion of the fibrils in PLA after modification. This study demonstrated that scalable water-based surface modification and subsequent straightforward oven drying could be a facile method for effectively drying cellulose nanomaterials. We find that the method helps significantly disperse fibrils in polymers and enhances the mechanical properties of microfibrillar cellulose-reinforced biocomposites.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Sub-melt nanosecond pulsed-laser induced densification and strain-field relaxation in single-crystal diamond

Dislocations and polishing-induced defect networks in synthetic diamond introduce local strain fields and broaden Raman features, limiting performance in optical, thermal, and electronic applications. Laser annealing is emerging as a promising approach to repair surface and near-surface defects in diamond without entering the melt regime, yet surface densification, defect-state modification, and associated structural changes have not been well quantified. In this work, we show that sub-melt nanosecond pulsed-laser annealing (PLA) induces near-surface densification and defect-mediated strain relaxation in single-crystal Chemical Vapor Deposition (CVD) diamond. Single- and two-pulse PLA were applied, and structural evolution was quantified using co-registered ISO 25,178 white-light interferometry, depth-resolved Raman spectroscopy, and cross-sectional STEM with geometric phase analysis (GPA). Across a 5 × 6 grid (n = 30), responsive regions exhibit large reductions in local slope (Sdq 45–65%), developed area (Sdr 60–90%), height spread (Sp, Sz 30–65%), void volume (Vv 57–60%), and roughness amplitude (Sa, Sq 48–57%), consistent with densification of ∼4–6.5 nm. Raman profiling shows narrowing of the diamond line and improved spectral uniformity to depths of ∼2–3 μm. Given that the Raman probing depth significantly exceeds the densified layer thickness, this response is interpreted as consistent with long-range strain-field redistribution originating from the near-surface region. STEM-GPA strain maps further support this interpretation, showing smoother strain fields, suppressed hotspots, and redistribution of localized strain concentrations following PLA. These results are consistent with defect-mediated strain relaxation and densification-driven modification of the near-surface energy state. The approach provides a scalable pathway for improving near-surface structural quality in diamond relevant to electronic, photonic, and quantum applications.

Areal surface metrology (ISO 25,178)↗

DOE OSTI2023

Bending and shear improvements in 3D-printed core sandwich composites through modification of resin uptake in the skin/core interphase region

Fused deposition modeling (FDM) printed polymers are rarely used as a structural material due to anisotropic and low mechanical properties compared with conventional composites. In recent years, greater need has been expressed for recycling of materials, such as recyclable FDM, at the end of service life to reduce environmental pollution and manufacture cost. However, how the amount of resin uptake in the skin and skin/core interphase affects the bending and shear performance of the sandwich composites when replacing the low strength and ductile core (conventional core) with a high strength and brittle core (FDM printed PLA (polylactic acid) core) still remains unclear. A new manufacturing routine is needed to improve the incorporation of FDM printed polymers in composite structures. In this work, FDM printed PLA was used as core material and sandwiched between two unidirectional glass fiber reinforced polymer (GFRP) skins to form a sandwich composite by compression-molding (CM) process, which provides a good manufacturing strategy for skin/core interphase modification. The significance of the CM process is proved by investigating the effect of resin uptake on bending and in-plane/out-of-plane shear performances. Current first order shear deformation (FSDT) theory lacks a direct connection between the in-plane shear stress and out-of-shear stress in the core region of sandwich composites. With the help of DIC, a connection between the in-plane shear and the out-of-plane shear strain was built and in-plane shear properties can acquire through out-of-plane shear properties, hence reducing the redundancy of sample preparation or the need for simulation. A significant improvement was found compared with the optimized resin uptake (Optimized resin uptake range: 20.43%–22.86 wt%) 3D-printed PLA core sandwich composite and lowest performance sandwich composite (Improvement: in-plane shear strength (~34%)/modulus (~29%), out-of-plane shear strength (~25%)/modulus (~31%), specific peak bending load (~19%)). Finally, compared with balsa core sandwich composites, the 3D-printed cores are suitable for use in composite sandwich structures in many applications with a satisfactory strength-to-weight ratio.

3D-printed core sandwich composite↗

DOE OSTI2024

Enhanced joining strength in additive-manufactured polylactic-acid structures fused by embedded heated metallic meshes

Additively manufactured thermoplastic polymers, such as polylactic acid (PLA), hold significant promise for sustainable engineering structures, including wind turbine blades. Upscaling these structures beyond the limitations of 3D printer build volumes is a challenge; fusion joining presents a potential solution. This paper introduces a displacement-controlled resistance welding process for PLA, as an alternative to the typical force-controlled methods. Here, we investigated the bonding quality of resistance-welded and adhesive-bonded PLA beams through three-point bending and measured the surface deformations using digital image correlation. Different metal meshes (30%/0.11 mm Ni—Cu, 34%/0.07 mm Ni—Cu, and 36%/0.25 mm Co—Ni) served as heating elements. The process parameters were varied for the 34%/0.07 mm Ni—Cu mesh to identify an optimum set of parameters. Results showed that this optimized displacement-controlled welding achieved 94% of the original strength of monolithic samples. This indicates that the new welding process not only ensures high-quality bonding and fine surface finishing but also promotes sustainability, recyclability, and economic efficiency in various polymer and composite structural applications.

Additive manufacturing↗

DOE OSTI2020

Resolving Triblock Terpolymer Morphologies by Vapor-Phase Infiltration

The spontaneous formation of well-organized three-dimensional (3D) nanostructures from self-assembled block copolymers (BCPs) holds promise for nanofabrication and lithography. The addition of a third block to BCPs provides access to a plethora of 3D geometries, but it remains difficult to resolve the geometry of such “three-color” structures when there is low contrast between the polymeric components at length scales of a few nm. Here, we apply vapor-phase infiltration synthesis to a silicon-containing triblock terpolymer, poly(1,1- dimethyl silacyclobutane-b-styrene-b-lactide) (PDMSB-b-PS-b-PLA or DSL) to distinguish the 3D microdomain morphologies of the two organic blocks, PLA and PS. Selective infiltration of ZnO within the PLA microdomains reveals morphologies consisting of three-color lamellae or lamellae combined with vertically aligned core-shell cylinders, depending on the volume fractions of each block. The infiltration produces ZnO nanoparticles throughout the 260 nm thickness of the DSL film, generating 3D nanocomposites containing ZnO and SiO x . These results provide a strategy for synthesizing multicomponent 3D nanostructures as well as visualizing the phase behavior of multi-block copolymers.

36 MATERIALS SCIENCE↗

DOE OSTI2024

High-strength 3D printed poly(lactic acid) composites reinforced by shear-aligned polymer-grafted cellulose nanofibrils

This work demonstrates the application of pilot-scale surface functionalization of cellulose nanofibrils (CNFs) by aqueous grafting-through polymerization and subsequent spray drying in 3D printed poly(lactic acid) (PLA) composites. Grafted-CNF composites attain an ultimate tensile strength of 88 ± 3 MPa and a tensile modulus of elasticity of 7.8 ± 1.3 GPa in the printing direction at 20 wt% reinforcement loading. These increases, 42% and 139% over neat PLA, respectively, represent the strongest reported 3D printed CNF/PLA composite to date in the literature. The mechanisms behind these improvements are investigated by comparisons to neat PLA and unmodified spray-dried CNF/PLA controls using melt rheology, dynamic mechanical analysis, and assessment of the reinforcement dispersion. These experiments reveal that improved network formation and shear-induced alignment of the grafted CNFs facilitate the remarkable tensile properties of the printed composites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Embedded Sensing in Additive Manufacturing Metal and Polymer Parts: A Comparative Study of Integration Techniques and Structural Health Monitoring Performance

This study presents a comparative evaluation of post-process sensor integration in additively manufactured (AM) metal and the in-situ process for polymer structures for structural health monitoring (SHM), with an emphasis on embedded sensors. Geometrically identical specimens were fabricated using copper via metal fused filament fabrication (FFF) and PLA via polymer FFF, with piezoelectric transducers (PZTs) inserted into internal cavities to assess the influence of material and placement on sensing fidelity. Mechanical testing under compressive and point loads generated signals that were transformed into time–frequency spectrograms using a Short-Time Fourier Transform (STFT) framework. An engineered RGB representation was developed, combining global amplitude scaling with an amplitude-envelope encoding to enhance contrast and highlight subtle wave features. These spectrograms served as inputs to convolutional neural networks (CNNs) for classification of load conditions and detection of damage-related features. Results showed reliable recognition in both copper and PLA specimens, with CNN classification accuracies exceeding 95%. Embedded PZTs were especially effective in PLA, where signal damping and environmental sensitivity often hinder surface-mounted sensors. This work demonstrates the advantages of embedded sensing in AM structures, particularly when paired with spectrogram-based feature engineering and CNN modeling, advancing real-time SHM for aerospace, energy, and defense applications.

additive manufacturing↗

NASA NTRSDate not supplied

Understanding the Feasibility of MAB Phase Structures for Lunar Applications

During the ten-week internship, my work focused on synthesis, characterization, and tailoring the flowability of the MAB phase powders for improving the surface finish and decreasing porosity of 3D-printed MAB phase structures. My mentor for the project was Dr. Samuel Hocker from NASA Langley and my faculty advisor was Dr. Surojit Gupta from the University of North Dakota. I also collaborated with Daniel Trieff from the University of North Dakota in developing characterization paradigm of 3D printed samples. The microencapsulation was performed via novel solvent casting-based microencapsulation process pioneered in UND, wherein a polymer (PLA, PHA) was dissolved into dichloromethane and precipitated onto the surface of the MoAlB particles. Two 100mL samples of microencapsulated powder was outsourced to Particle Technology Labs for flowability testing along with a 100mL control sample to determine if microencapsulation is a valid method for improving the flowability. The microencapsulated powders were characterized using SEM, Differential Scanning Calorimetry, and optical microscopy. The SEM images showed no change between the pure and microencapsulated powders. The optical microscopy analysis indicated a reduction in reflectivity for the PLA microencapsulated powders as well as hydrophobic properties. Both results suggest that microencapsulation was successful as PLA is a hydrophobic polymer and the change in reflectivity could be a result of the light being dispersed through the polymer coating. A reflectivity analysis will be done to bring more perspective to these observations. If powder flowability is improved, then the project will move forward with testing the printability of the microencapsulated powders and characterizing the structures using the designed characterization protocol. We are waiting for the DSC results. The characterization protocol for the 3D-printed MAB structures included a visual inspection of the plates to rule out any samples that had spalled or delaminated, optical microscopy to document surface features, porosity, and decomposition, and cleaning of the plates using an ultrasonic bath in preparation for SEM, EDS, and profilometry analyses.

MAB Phase↗

NASA NTRSDate not supplied

Beyond Gravity Single Launch Payload Accommodations Shock Testing

The Vulcan Centaur launch vehicle is purpose-built to meet all the U.S. government’s National Security Space Launch (NSSL) needs. A shock test for the Centaur V’s payload accommodations (PLA), single launch (SL) configuration was successfully conducted at NASA’s Marshall Space Flight Center (MSFC) in Huntsville, Alabama, in May 2021. This test was a joint effort between MSFC, Beyond Gravity and United Launch Alliance. The primary purpose of the shock test was to characterize the shock environment induced by the separation event on components attached to the PLA and its interfaces. Additional test requirements included: (1) verifying the payload fairing (PLF) did not contact the flight hardware during the mechanical separation of the PLF horizontal separation system (HSS) and (2) evaluating the performance of the HSS spring packages during jettison. The data acquired during the PLF SL shock test will be used to validate the shock predictions from pre-test analysis of the launch vehicle and the PLF separation analysis. This paper provides an overview of the PLA SL shock test planning and execution as well as the required catch system, instrumentation and results.

separation↗

NASA NTRSDate not supplied

Beyond Gravity Single Launch Payload Accommodations Shock Testing

separation↗

NASA NTRSDate not supplied

Beyond Gravity Single Launch Payload Accommodations Shock Testing

separation↗

DOE OSTI2024

Unleashing the potential of waste: A supercharged high-performance 3D printing resin from discarded polylactic acid

In additive manufacturing/3D printing, the limitation no longer lies in people’s imagination but in the very materials that one can print with. While the additive manufacturing process can virtually create any geometry, available applications are often limited by factors like parts’ mechanical strength, glass transition temperature, and heat deflection temperature. These factors are especially critical for polymer-based printing. Here we introduce a simple formulation derived from the aminolysis of polylactic acid (PLA) plastic waste, namely the N-lactoyl ethanolamine (N-LEA). The N-LEA is next reacted with excess methacrylic anhydride, forming a photo-crosslinkable resin for MSLA 3D printing. The resulting 3D printed part has a set of impressive properties that is unrivaled amongst engineering grade 3D printing resins on the market and research literature. The 3D printed part has an ultrahigh tensile strength of 131.7 MPa, glass transition at ~190 °C, and heat deflection temperature at 162.6 °C. Furthermore, this work demonstrates a true upcycling approach for turning PLA waste into a value-added product in a simple and efficient manner while also expanding the high-performance material portfolio available for photocuring additive manufacturing.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Journal Pre-proof3D printed polylactic acid and acrylonitrile butadiene styrene fluidicstructures for biological applications: tailoring bio-material interfaceviasurface modification

Three-dimensional (3D) printing is a rapidly growing technology that best fits for cell culture and other biological applications due to its potential to build immensely complex structures from customized designs. However, use of 3D printed structures for cell adhesion, proliferation, and activation requires tailoring of surface characteristics. In this context, this work investigates the use of two biocompatible 3D printable polymer materials, Poly-L-lactic Acid (PLA) and Acrylonitrile Butadiene Styrene (ABS) for bio applications, and the effect of their post-printing surface modification processes to achieve desired bio functionality. Three post-printing surface modification techniques, alkaline hydrolysis, ultraviolet ozone plasma irradiation and gold thin film deposition are performed with the objective of introducing useful levels of surface functionalities. Poly-L-lysine (PLL) labelled with FITC chromophore is immobilized on the surface modified samples following standard protocols. The effect of surface roughness and porosity of the 3D printed structures on the polypeptide immobilization is compared on as-printed versus mechanically polished surfaces. Different characterization methods, viz., Fluorescence microscopy, Raman Spectroscopy and UV–vis spectroscopy, are used to study the efficacy of the surface modification and PLL immobilization techniques. Our results demonstrated denser PLL attachment on polished hydrolyzed PLA and ABS surfaces which enables the use of these printable polymers for a range of applications such as tissue scaffolds and microfluidics.

3D Printing, PLA, ABS, Biodegradable Polymer, Surf↗

DOE OSTI2023

A hybrid chemical-biological approach can upcycle mixed plastic waste with reduced cost and carbon footprint

Derived from renewable feedstocks, such as biomass, polylactic acid (PLA) is considered a more environmentally friendly plastic than conventional petroleum-based polyethylene terephthalate (PET). However, PLA must still be recycled, and its growing popularity and mixture with PET plastics at the disposal stage poses a cross-contamination threat in existing recycling facilities and results in low-value and low-quality recycled products. Hybrid upcycling has been proposed as a promising sustainable solution for mixed plastic waste, but its techno-economic and life cycle environmental performance remain understudied. We propose a hybrid upcycling approach using a biocompatible ionic liquid (IL) to first chemically depolymerize plastics and then convert the depolymerized stream via biological upgrading with no extra separation. Here we show that over 95% of mixed PET/PLA was depolymerized into the respective monomers, which then served as the sole carbon source for the growth of Pseudomonas putida, enabling the conversion of the depolymerized plastics into biodegradable polyhydroxyalkanoates (PHAs). In comparison to conventional commercial PHAs, the estimated optimal production cost and carbon footprint are reduced by 62% and 29%, respectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Fine grinding of thermoplastics by high speed friction grinding assisted by guar gum

High speed friction grinding has been used to grind plant and food substances in water but never been explored for grinding of thermoplastics like polylactic acid (PLA), low and high density polyethylene and polypropylene. Such grinding was investigated in this work and was made possible by using 0.5% guar gum solution instead of just water because increasing the viscosity of water reduced their settling and the speed of passing through the grinder. Additionally, tensile, flexural, and impact strengths of the plastics were studied and higher grinding efficiency of PLA could be explained by its low elongation-at-break compared to low density polyethylene, high density polyethylene, and polypropylene. The microplastics (2000–45 μm) were studied for mass and particle size distributions and by scanning electron microscopy, 13 C CP/MAS NMR, Fourier transform infrared spectroscopy, differential scanning calorimetry, and thermogravimetric analysis. In addition, viscosity of guar gum and contact angles was measured. This new technology can produce finely ground microplastics (710–45 μm) for a variety of applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Engineering hybrid textile braids for tendon and ligament repair application

Abstract Challenges involving tendon and ligament repair have motivated the investigation of new strategies to improve clinical outcomes. These have been mainly based on polymer constructs, which may be non‐biodegradable or biodegradable. The former typically fails due to lack of device integration and the latter demands a complex balance between biodegradability and tissue ingrowth, often failing due to insufficient mechanical properties. This work presents the development of hybrid braids based on polyethylene terephthalate (PET) and polylactic acid (PLA) yarns. A textile technique was used to fabricate braids based on 16 multifilament yarns of varying PLA/PET composition. The composition was varied to maximize biodegradability while ensuring mechanical performance. The braids' morphology, physical and mechanical properties were characterized. As production parameters and architecture were maintained, the braids exhibited similar porosity and wicking ability. The breaking force and stiffness decreased significantly as the number of PLA yarns increased, although strain levels remained constant. Braids containing 10 and 12 PET yarns (out of the total 16 yarns) demonstrated good creep and force‐relaxation behavior, as well as resistance to cyclic loading. These compositions were selected for future work, to be assembled into more elaborate structures to mimic the fibrous organization and tensile properties of different tendons/ligaments.

Peixoto, Tânia↗

DOE OSTI2025

Utilization of Hemp Processing Waste for 3D Printing of Biocomposites

Unlike stem biomass, the residues after the extraction of cannabidiol (CBD) oil from hemp flower are challenging to utilize because of their high extractive content (~ 40%, mainly lipids) and are typically considered waste and landfilled. This study presented a novel approach to effectively valorize this underutilized hemp processing waste via chemical processing for three-dimensional (3D) printing applications. Hemp processing waste was processed with sodium hydroxide (NaOH) to control extractives for solving nozzle clogging and then applied as a biofiller in polylactic acid (PLA) composites to improve the mechanical strength. The novelty of this work lies in demonstrating that controlled extractive removal via NaOH treatment not only improves processability but also enhances mechanical performance in 3D-printed biocomposites. We systematically investigated the effect of the processed biofiller content (2.5–10 wt%) on the mechanical and thermal properties of the biocomposites. The decrease in the content of extractives reduced the non-structural components and improved the surface compatibility of the hemp waste with the PLA matrix, thereby enhancing the polymer-biofiller interactions. The best performance was achieved at 2.5 wt% loading, where Young’s modulus increased from 2.3 GPa to 2.6 GPa and tensile strength from 42.7 MPa to 48.8 MPa. Interestingly, the complete removal of extractives also reduced the mechanical strength of their biocomposites, indicating the interfacial adhesion effects of extractives. Furthermore, this study provides new insights into balancing extractive content for optimal mechanical properties, offering a sustainable solution for waste valorization in additive manufacturing.

Additive manufacturing↗