Results for “PLASTIC MATERIAL” — Page 4

NASA NTRS1972

Void growth in an elastic-plastic medium.

The uniaxial deformation of an elastic-plastic medium containing a doubly periodic square array of circular cylindrical voids is studied under plane-strain conditions. Both the effects of geometrical nonlinearities resulting from large deformation and physical nonlinearities arising from plastic material behavior are included in formulating the problem. A variational principle is used as the basis for implementing a finite-element solution. Results are obtained for the change in void shape and size under increasing overall strain, the overall tensile behavior of the material with voids, and the development of the plastic zone about a void.

Needleman, A.↗

NASA NTRS1950

The interpretation of biaxial-tension experiments involving constant stress ratios

Explore the source record for details and available documents.

DIAGRAMS, STRESS-STRAIN↗

NASA NTRS1973

Catalysis study for space shuttle vehicle thermal protection systems

Experimental results on the problem of reducing aerodynamic heating on space shuttle orbiter surfaces are presented. Data include: (1) development of a laboratory flow reactor technique for measuring gamma sub O and gamma sub N on candidate materials at surfaces, T sub w, in the nominal range 1000 to 2000, (2) measurements of gamma sub O and gamma sub N above 1000 K for both the glass coating of a reusable surface insulation material and the siliconized surface of a reinforced pyrolyzed plastic material, (3) measurement of the ablation behavior of the coated RPP material at T sub w is greater than or equal to 2150 K, (4) X-ray photoelectron spectral studies of the chemical constituents on these surfaces before and after dissociated gas exposure, (5) scanning electron micrograph examination of as-received and reacted specimens, and (6) development and exploitation of a method of predicting the aerodynamic heating consquences of these gamma sub O(T sub w) and gamma sub N(T sub w) measurements for critical locations on a radiation cooled orbiter vehicle.

Breen, J.↗

NASA NTRS1972

Investigation of the Ignition and Burning of Materials in Space Cabin Atmospheres. Part 1: Ignition and Burning of Material

An analytical study of the theory of ignition and burning of a plastic material immersed in an atmosphere of a space cabin which may be subjected to gravity force changes is considered. The hazardous condition in a space cabin environment where the changes of gravity may effect the combustion process is evaluated. The model considered the analysis of the coupled gas and solid phases and is based on the premise that material heating leads to the formation of pyrolysis gases from the decomposed solid which then react with the ambient oxidizer to further the combustion process. Moreover, free convection plays a dominant role in transporting these hot gases to the virgin material. A time-dependent study of the coupled gas-solid model as required for ignition processes with emphasis on the surface energy interchange of the gas and solid phases has been made. Detailed distribution of species composition and temperature patterns provide a spatial and time map of the evolving gases from the material combustion.

Lew, H. G.↗

DOE OSTI2024

A non-isothermal breakage-damage model for plastic-bonded granular materials incorporating temperature, pressure, and rate dependencies

Plastic-bonded granular materials (PBM) are widely used in industrial sectors, including building construction, abrasive applications, and defense applications such as plastic-bonded explosives. The mechanical behavior of PBM is highly nonlinear, irreversible, rate dependent, and temperature sensitive governed by various micromechanical attributions such as grain crushing and binder damage. This paper presents a thermodynamically consistent, microstructure-informed constitutive model to capture these characteristic behaviors of PBM. Key features of the model include a breakage internal variable to upscale the grain-scale information to the continuum level and to predict grain size evolution under mechanical loading. In addition, a damage internal state variable is introduced to account for the damage, deterioration, and debonding of the binder matrix upon loading. Temperature is taken as a fundamental external state variable to handle non-isothermal loading paths. The proposed model is able to capture with good accuracy several important aspects of the mechanical properties of PBM, such as pressure-dependent elasticity, pressure-dependent yield strength, brittle-to-ductile transition, temperature dependency, and rate dependency in the post-yielding regime. Furthermore, the model is validated against multiple published datasets obtained from confined and unconfined compression tests, covering various PBM compositions, confining pressures, temperatures, and strain rates.

Breakage↗

NASA NTRS1986

Recent studies of energy integrals and their applications

In this paper, recent studies concerning path independent integrals, of relevance in the fracture of solids, and the applications of these integrals, are critically summarized. Specific topics dealt with include: (1) unsteady dynamic crack-propagation in (nonlinear) elastic solids and (2) slow stable, as well as fast crack propagation in elastic-plastic materials, which are characterized by an (incremental) flow theory of plasticity, and which are subject to arbitrary loading (and unloading) histories.

Atluri, S. N.↗

NASA NTRS1983

Application of an Uncoupled Elastic-plastic-creep Constitutive Model to Metals at High Temperature

A uniaxial, uncoupled constitutive model to predict the response of thermal and rate dependent elastic-plastic material behavior is presented. The model is based on an incremental classicial plasticity theory extended to account for thermal, creep, and transient temperature conditions. Revisions to he combined hardening rule of the theory allow for better representation of cyclic phenomenon including the high rate of strain hardening upon cyclic reyield and cyclic saturation. An alternative approach is taken to model the rate dependent inelastic deformation which utilizes hysteresis loops and stress relaxation test data at various temperatures. The model is evaluated and compared to experiments which involve various thermal and mechanical load histories on 5086 aluminum alloy, 304 stainless steel and Hastelloy-X.

Haisler, W. E.↗

NASA NTRS1989

Parallel processors and nonlinear structural dynamics algorithms and software

A nonlinear structural dynamics finite element program was developed to run on a shared memory multiprocessor with pipeline processors. The program, WHAMS, was used as a framework for this work. The program employs explicit time integration and has the capability to handle both the nonlinear material behavior and large displacement response of 3-D structures. The elasto-plastic material model uses an isotropic strain hardening law which is input as a piecewise linear function. Geometric nonlinearities are handled by a corotational formulation in which a coordinate system is embedded at the integration point of each element. Currently, the program has an element library consisting of a beam element based on Euler-Bernoulli theory and trianglar and quadrilateral plate element based on Mindlin theory.

Belytschko, Ted↗

NASA NTRS2022

Impact Simulation of Composite Panels for Aerospace Applications

The aerospace research community has been working towards the development of a comprehensive framework for the design of composite structures at the component, subassembly, assembly, and system levels. Such a framework requires accurate, efficient and easy-to-use mathematical and computational models that are in sync with physical reality. The research work in this paper is designed to help an aerospace structural engineer move towards this goal by simulating dynamic impact to composite panels. First, the existing orthotropic visco-elastic visco-plastic material model in LS-DYNA commercial finite element program, MAT_COMPOSITE_TABULATED_PLASTICITY_DAMAGE (MAT_213) is enhanced with the development and use of rate-dependent damage data. Using state-of-the-art experimental procedures, impact validation test data are created. Second, the versatility of the constitutive model is examined by its ability to simulate a low velocity (27 ft/s, 8 m/s) impact test, and two high velocity impact tests (385–417 ft/s, 117–127 m/s) that straddle the ballistic limit of the projectile and the composite panels. Third, these impact events are modeled using three different finite element types – under-integrated and fully-integrated solid elements, and fully-integrated thin shell elements. Insight into accuracy versus numerical efficiency is gained by comparing the performance of solid versus thin shell elements. The numerical results show that accurate predictions of these impact events can be obtained with reasonable effort and care.

Simulations↗

DOE OSTI2026

The effect of dogbone sample size in the tensile testing of TATB-based plastic‑bonded explosive materials

Mechanical properties are of interest for many plastic‑bonded explosive (PBX) materials with tensile properties being of particular interest. Direct tensile measurements using dogbone-shaped samples are considered the gold standard, but they are fairly large, making testing more costly and less desirable from a safety perspective. We investigated whether the measured tensile strength depends on the dogbone specimen size, which to our knowledge, has not been reported in the literature for PBX materials. Understanding this should inform the feasibility of employing smaller samples and how sample size should be considered when comparing PBX dogbone values in the literature. The TATB-based PBX dogbone sample size was varied by (a) scaling all dimensions proportionally and (b) varying only the length of the samples. It was observed that the measured tensile peak stress (strength) was a function of the sample size, and was more dependent on the diameter (cross-sectional area) than the length of the samples. Since peak stress is calculated as peak force normalized to the diameter of the sample, one might not expect an explicit diameter dependence for the peak stress. Therefore, these results suggest there may be an additional strengthening effect as the sample diameter is increased.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1999

A Single-Lap Joint Adhesive Bonding Optimization Method Using Gradient and Genetic Algorithms

A natural process for any engineer, scientist, educator, etc. is to seek the most efficient method for accomplishing a given task. In the case of structural design, an area that has a significant impact on the structural efficiency is joint design. Unless the structure is machined from a solid block of material, the individual components which compose the overall structure must be joined together. The method for joining a structure varies depending on the applied loads, material, assembly and disassembly requirements, service life, environment, etc. Using both metallic and fiber reinforced plastic materials limits the user to two methods or a combination of these methods for joining the components into one structure. The first is mechanical fastening and the second is adhesive bonding. Mechanical fastening is by far the most popular joining technique; however, in terms of structural efficiency, adhesive bonding provides a superior joint since the load is distributed uniformly across the joint. The purpose of this paper is to develop a method for optimizing single-lap joint adhesive bonded structures using both gradient and genetic algorithms and comparing the solution process for each method. The goal of the single-lap joint optimization is to find the most efficient structure that meets the imposed requirements while still remaining as lightweight, economical, and reliable as possible. For the single-lap joint, an optimum joint is determined by minimizing the weight of the overall joint based on constraints from adhesive strengths as well as empirically derived rules. The analytical solution of the sin-le-lap joint is determined using the classical Goland-Reissner technique for case 2 type adhesive joints. Joint weight minimization is achieved using a commercially available routine, Design Optimization Tool (DOT), for the gradient solution while an author developed method is used for the genetic algorithm solution. Results illustrate the critical design variables as a function of adhesive properties and convergences of different joints based on the two optimization methods.

Smeltzer, Stanley S., III↗

DOE OSTI2024

Modeling inter- and intra-granular dislocation transport using crystal plasticity

Here, this work presents the development of a crystal plasticity material model that incorporates both dislocation transport within grains and dislocation transfer across grain boundaries. This model has been implemented in the open-source finite element code MOOSE. In addition, a novel geometry-based criterion is developed to determine the direction of dislocation transfer across grain boundaries. The transfer criterion incorporates the geometric features of the grain boundary, such as the grain boundary plane normal, and its misorientation, which is accounted for through the orientation of the incoming and outgoing slip systems. The model is tested with several cases, including a copper single crystal, bi-crystal, and polycrystal. The development of the transfer criterion, implementation of the model, and its application to these test cases are discussed in detail.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Towards a Circular Economy for PET Bottles in the U.S. - 4P Model

The United States generates the most plastic waste of any country. Along with that GHG emissions from the global plastic economy are expected to increase to 15% of the global carbon budget by 2050. It is imperative that plastic recycling is made a reality to reduce both plastic pollution in the environment and GHG emissions. A portfolio of end-of-life strategies must be implemented to minimize environmental impacts and retain valuable plastic material, but it is challenging to compare options that generate products with different utility and lifetime. Plastic use reduction, reuse and recycling are thus increasingly important, but making informed policy and research decisions within this space can be challenging given the diverse range of available solutions. The novel analysis framework, Plastic Parallel Pathways Platform (4P) has been equipped with consequential life cycle assessment, techno-economic analysis, and a plastic circularity indicator to estimate the greenhouse gas (GHG) emissions, circularity, and cost of polyethylene terephthalate (PET) down-cycling to lower-quality resin, closed-loop recycling to food-grade PET bottles, up-cycling to fiber-reinforced plastic (FRP), and conversion to non-plastic products (electricity, oil) on a United States economy-wide basis. Integrating system dynamics into this robust plastics model that already incorporates techno-economics, circularity, and environmental impacts will enable identification of key bottlenecks between manufacturers, waste sorters, and reclaimers that currently prevent rapid decarbonization of the plastics economy. System dynamics (SD) explore the evolution of activities and technologies based on changed macro parameters such as plastic demand and supply, market shifts, and cross-sectoral interactions. This project particularly aims to explore the interplay between, waste collection, plastic waste sorting, recycling, and manufacturing, as well as the effect of plastic bale quality and plastic reuse initiatives on the surrounding process stages. This functionality will facilitate combinatory analysis in which a portfolio of end-of-life pathways are assessed simultaneously, with the exact makeup of that portfolio affected by parameters such as technology scales, resource constraints, and waste mitigation efforts. Integrating SD with the 4P framework enables analyzing the effect of increased revenue and reinvestment into improving process efficiencies, sorting and collection quantities. Through that, market effects of increased recycled resin availability can be studied for the plastics systems model for the US. The results will help identify technical or economic bottlenecks that currently limit efforts to decarbonize the U.S. plastics economy.

carbon↗

DOE OSTI2024

Towards a Circular Economy for PET Bottles in the U.S. - 4P Framework

The United States generates the most plastic waste of any country. Along with that GHG emissions from the global plastic economy are expected to increase to 15% of the global carbon budget by 2050. It is imperative that plastic recycling is made a reality to reduce both plastic pollution in the environment and GHG emissions. A portfolio of end-of-life strategies must be implemented to minimize environmental impacts and retain valuable plastic material, but it is challenging to compare options that generate products with different utility and lifetime. Plastic use reduction, reuse and recycling are thus increasingly important, but making informed policy and research decisions within this space can be challenging given the diverse range of available solutions. The novel analysis framework, Plastic Parallel Pathways Platform (4P) has been equipped with consequential life cycle assessment, techno-economic analysis, and a plastic circularity indicator to estimate the greenhouse gas (GHG) emissions, circularity, and cost of polyethylene terephthalate (PET) down-cycling to lower-quality resin, closed-loop recycling to food-grade PET bottles, up-cycling to fiber-reinforced plastic (FRP), and conversion to non-plastic products (electricity, oil) on a United States economy-wide basis. Integrating system dynamics into this robust plastics model that already incorporates techno-economics, circularity, and environmental impacts will enable identification of key bottlenecks between manufacturers, waste sorters, and reclaimers that currently prevent rapid decarbonization of the plastics economy. System dynamics (SD) explore the evolution of activities and technologies based on changed macro parameters such as plastic demand and supply, market shifts, and cross-sectoral interactions. This project particularly aims to explore the interplay between, waste collection, plastic waste sorting, recycling, and manufacturing, as well as the effect of plastic bale quality and plastic reuse initiatives on the surrounding process stages. This functionality will facilitate combinatory analysis in which a portfolio of end-of-life pathways are assessed simultaneously, with the exact makeup of that portfolio affected by parameters such as technology scales, resource constraints, and waste mitigation efforts. Integrating SD with the 4P framework enables analyzing the effect of increased revenue and reinvestment into improving process efficiencies, sorting and collection quantities. Through that, market effects of increased recycled resin availability can be studied for the plastics systems model for the US. The results will help identify technical or economic bottlenecks that currently limit efforts to decarbonize the U.S. plastics economy.

circular economy↗

NASA NTRS1978

Foam For Filtering

Like nature's honeycomb, foam is a structure of many-sided cells, apparently solid but actually only three percent material and 97 percent air. Foam is made by a heat-producing chemical reaction which expands a plastic material in a manner somewhat akin to the heat-induced rising of a loaf of bread. The resulting structure of interconnected cells is flexible yet strong and extremely versatile in applicati6n. Foam can, for example, be a sound absorber in one form, while in another it allows sound to pass through it. It can be a very soft powder puff material and at the same time a highly abrasive scrubber. A sampling of foam uses includes stereo speaker grilles, applying postage meter ink, filtering lawnmower carburetor air; deadening noise in trucks and tractors, applying cosmetics, releasing fabric softener and antistatic agents in home clothes dryers, painting, filtering factory heating and ventilating systems, shining shoes, polishing cars, sponge-mopping floors, acting as pre-operative surgical scrubbers-the list is virtually limitless. The process by which foam is made produces "windows," thin plastic membranes connecting the cell walls. Windowed foam is used in many applications but for certain others-filtering, for example-it is desirable to have a completely open network. Scott Paper Company's Foam Division, Chester, Pennsylvania, improved a patented method of "removing the windows," to create an open structure that affords special utility in filtering applications. NASA technology contributed to Scott's improvement.

Source record↗

NASA NTRS1987

Experiments of the selection of a method evaluating the fire resistance of some materials based on macromolecular compounds

A comparative experimental study on the application of various tests for the evaluation of the fire-resistant properties of plastic materials is presented. On the basis of the results obtained conclusions are drawn on the advantages and disadvantages of the methods used, and a preferred test method is picked, i.e., the introduction of fire retardant materials into the polymers.

Stoica, Steln↗

NASA NTRS1976

Nonelastomeric Rod Seals for Advanced Hydraulic Systems

Advanced high temperature hydraulic system rod sealing requirements can be met by using seals made of nonelastomeric (plastic) materials in applications where elastomers do not have adequate life. Exploratory seal designs were optimized for advanced applications using machinable polyimide materials. These seals demonstrated equivalent flight hour lives of 12,500 at 350 F and 9,875 at 400 F in advanced hydraulic system simulation. Successful operation was also attained under simulated space shuttle applications; 96 reentry thermal cycles and 1,438 hours of vacuum storage. Tests of less expensive molded plastic seals indicated a need for improved materials to provide equivalent performance to the machined seals.

Hady, W. F.↗

NASA NTRS1991

Elasto-plastic coupled temperature-displacement finite element analysis of two-dimensional rolling-sliding contact with a translating heat source

The present paper describes a transient translating elastoplastic thermomechanical finite element model to study two-dimensional frictional rolling contact. Frictional two-dimensional contact is simulated by repeatedly translating a nonuniform thermomechanical distribution across the surface of an elastoplastic half space. The half space is represented by a two-dimensional finite element mesh with appropriate boundaries. Calculations are for an elastic-perfectly plastic material and the selected thermophysical properties are assumed to be temperature independent. The paper presents temperature variations, stress and plastic strain distributions and deformations. Residual tensile stresses are observed. The magnitude and depth of these stresses depends on (1) the temperature gradients and (2) the magnitudes of the normal and tangential tractions.

Rubin, C. A.↗