Search NASA⌕ Search

SEARCH · Search NASA

Results for “PRESSURE RECOVERY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1952

Pressure recovery, drag, and subcritical stability characteristics of conical supersonic diffusers with boundary-layer removal

A study of two 20 degrees half-angle, low mass-flow ratio conical supersonic inlets with cone boundary-layer bleed was made on a 16-inch ram-jet engine in the Lewis 8- by 6-foot supersonic wind tunnel. A greater stable subcritical range of operation was obtained with the bleed inlets than with the corresponding inlet without boundary-layer bleed. The drag added by the bleed system was small.

Obey, Leonard T↗
NASA NTRS1983

A vortex venturi for reverting antimisting fuel properties

The level of degradation of antimisting fuel polymers such as FM-9 which must be accomplished in order to use antimisting fuel in existing engines may require the use of cavitation. The hydrodynamic shear produced by the collapse of vapor bubbles is capable of producing more splitting of polymeric molecules than mechanically-induced shear. A program has been carried out to investigate the possibility of using a cavitating venturi with rotating flow as a fuel reverter. This investigation included the effects of a swirl-inducing twisted tape upstream of the throat, inlet pressure, recovery pressure ratio and a pintle for varying throat area. A correlation of the data was produced, system concepts for using the vortex venturi were investigated and problem areas were delineated.

Szetela, E. J.↗
NASA NTRS1953

Performance Characteristics of Plane-Wall Two-Dimensional Diffusers

Experiments have been made at Stanford University to determine the performance characteristics of plane-wall, two-dimensional diffusers which were so proportioned as to insure reasonable approximation of two-dimensional flow. All of the diffusers had identical entrance cross sections and discharged directly into a large plenum chamber; the test program included wide variations of divergence angle and length. During all tests a dynamic pressure of 60 pounds per square foOt was maintained at the diffuser entrance and the boundary layer there was thin and fully turbulent. The most interesting flow characteristics observed were the occasional appearance of steady, unseparated, asymmetric flow - which was correlated with the boundary-layer coalescence - and the rapid deterioration of flow steadiness - which occurred as soon as the divergence angle for maximum static pressure recovery was exceeded. Pressure efficiency was found to be controlled almost exclusively by divergence angle, whereas static pressure recovery was markedly influenced by area ratio (or length) as well as divergence angle. Volumetric efficiency. diminished as area ratio increased, and at a greater rate with small lengths than with large ones. Large values of the static-pressure-recovery coefficient were attained only with long diffusers of large area ratio; under these conditions pressure efficiency was high and. volumetric efficiency low. Auxiliary tests with asymmetric diffusers demonstrated that longitudinal pressure gradient, rather than wall divergence angle, controlled flow separation. Others showed that the addition of even a short exit duct of uniform section augmented pressure recovery. Finally, it was found that the installation of a thin, central, longitudinal partition suppressed flow separation in short diffusers and thereby improved pressure recovery

Reid, Elliott G↗
NASA NTRS1954

Theoretical and Experimental Analysis of Low-Drag Supersonic Inlets Having a Circular Cross Section and a Central Body at Mach Numbers 3.30, 2.75, and 2.45

Contains theoretical and experimental analysis of circular inlets having a central body at Mach numbers of 3.30, 2.75, and 2.45. The inlets have been designed in order to have low drag and high pressure recovery. The pressure recoveries obtained are of the same order of magnitude as those previously obtained by inlets having very large external drag.

Ferri, Antonio↗
NASA NTRS2016

Vortex Generators in a Two-Dimensional, External-Compression Supersonic Inlet

Vortex generators within a two-dimensional, external-compression supersonic inlet for Mach 1.6 were investigated to determine their ability to increase total pressure recovery, reduce total pressure distortion, and improve the boundary layer. The vortex generators studied included vanes and ramps. The geometric factors of the vortex generators studied included height, length, spacing, and positions upstream and downstream of the inlet terminal shock. The flow through the inlet was simulated through the computational solution of the steady-state Reynolds-averaged Navier-Stokes equations on multi-block, structured grids. The vortex generators were simulated by either gridding the geometry of the vortex generators or modeling the vortices generated by the vortex generators. The inlet performance was characterized by the inlet total pressure recovery, total pressure distortion, and incompressible shape factor of the boundary-layer at the engine face. The results suggested that downstream vanes reduced the distortion and improved the boundary layer. The height of the vortex generators had the greatest effect of the geometric factors.

computational fluid dynamics↗
NASA NTRS1974

Low-speed wind-tunnel investigation of the aerodynamic and acoustic performance of a translating grid choked flow inlet

The aerodynamic and acoustic performance of a translating grid choked-flow inlet was determined in a low-speed wind tunnel at free-stream velocities of 24, 32, and 45 m/sec and incidence angles of 0, 10, 20, 30, 35, 40, 45, and 50 deg. The inlet was sized to fit a 13.97- centimeter-diameter fan with a design weight flow of 2.49 kg/sec. Measurements were made to determine inlet total pressure recovery, flow distortion, and sound pressure level for both choked and unchoked geometries over a range of inlet weight flows. For the unchoked geometry, inlet total pressure recovery ranged from 0.983 to 0.989 at incidence angles less than 40 deg. At 40 deg incidence angle, inlet cowl separation was encountered which resulted in lower values of pressure recovery and higher levels of fan broadband noise. For the choked geometry, increasing total pressure losses occurred with increasing inlet weight flow that prevented the inlet from reaching full choked conditions with the particular fan used. These losses were attributed to the high Mach number drag rise characteristics of airfoil grid. At maximum attainable inlet weight flow, the total pressure recovery at static conditions was 0.935. The fan blade passing frequency and other fan generated pure tones were eliminated from the noise spectrum, but the broadband level was increased.

Abbott, J. M.↗
NASA NTRS2006

Numerical Modeling of Flow Control in a Boundary-Layer-Ingesting Offset Inlet Diffuser at Transonic Mach Numbers

This paper will investigate the validation of a NASA developed, Reynolds-averaged Navier-Stokes (RANS) flow solver, OVERFLOW, for a boundary-layer-ingesting (BLI) offset (S-shaped) inlet in transonic flow with passive and active flow control devices as well as the baseline case. Numerical simulations are compared to wind tunnel results of a BLI inlet conducted at the NASA Langley 0.3-Meter Transonic Cryogenic Tunnel. Comparisons of inlet flow distortion, pressure recovery, and inlet wall pressures are performed. The numerical simulations are compared to the BLI inlet data at a freestream Mach number of 0.85 and a Reynolds number of approximately 2 million based on the length of the fan-face diameter. The numerical simulations with and without wind tunnel walls are performed, quantifying effects of the tunnel walls on the BLI inlet flow measurements. The wind tunnel test evaluated several different combinations of jet locations and mass flow rates as well as a vortex generator (VG) vane case. The numerical simulations will be performed on a single jet configuration for varying actuator mass flow rates at a fix inlet mass flow condition. Validation of the numerical simulations for the VG vane case will also be performed for varying inlet mass flow rates. Overall, the numerical simulations were able to predict the baseline circumferential flow distortion, DPCPavg, very well for comparisons made within the designed operating range of the BLI inlet. However the CFD simulations did predict a total pressure recovery that was 0.01 lower than the experiment. Numerical simulations of the baseline inlet flow also showed good agreement with the experimental inlet centerline surface pressures. The vane case showed that the CFD predicted the correct trends in the circumferential distortion for varying inlet mass flow but had a distortion level that was nearly twice as large as the experiment. Comparison to circumferential distortion measurements for a 15 deg clocked 40 probe rake indicated that the circumferential distortion levels are very sensitive to the symmetry of the flow and that a miss alignment of the vanes in the experiment could have resulted in this difference. The numerical simulations of the BLI inlet with jets showed good agreement with the circumferential inlet distortion levels for a range of jet actuator mass flow ratios at a fixed inlet mass flow rate. The CFD simulations for the jet case also predicted an average total pressure recovery that was 0.01 lower than the experiment as was seen in the baseline. Comparison of the flow features the jet case revealed that the CFD predicted a much larger vortex at the engine fan-face when compare to the experiment.

Allan Brian G.↗
NASA NTRS2006

Numerical Modeling of Flow Control in a Boundary-Layer-Ingesting Offset Inlet Diffuser at Transonic Mach Numbers

This paper will investigate the validation of the NASA developed, Reynolds-averaged Navier-Stokes (RANS) flow solver, OVERFLOW, for a boundary-layer-ingesting (BLI) offset (S-shaped) inlet in transonic flow with passive and active flow control devices as well as a baseline case. Numerical simulations are compared to wind tunnel results of a BLI inlet experiment conducted at the NASA Langley 0.3-Meter Transonic Cryogenic Tunnel. Comparisons of inlet flow distortion, pressure recovery, and inlet wall pressures are performed. The numerical simulations are compared to the BLI inlet data at a free-stream Mach number of 0.85 and a Reynolds number of approximately 2 million based on the fanface diameter. The numerical simulations with and without tunnel walls are performed, quantifying tunnel wall effects on the BLI inlet flow. A comparison is made between the numerical simulations and the BLI inlet experiment for the baseline and VG vane cases at various inlet mass flow rates. A comparison is also made to a BLI inlet jet configuration for varying actuator mass flow rates at a fixed inlet mass flow rate. Overall, the numerical simulations were able to predict the baseline circumferential flow distortion, DPCP avg, very well within the designed operating range of the BLI inlet. A comparison of the average total pressure recovery showed that the simulations were able to predict the trends but had a negative 0.01 offset when compared to the experimental levels. Numerical simulations of the baseline inlet flow also showed good agreement with the experimental inlet centerline surface pressures. The vane case showed that the CFD predicted the correct trends in the circumferential distortion levels for varying inlet mass flow but had a distortion level that was nearly twice as large as the experiment. Comparison to circumferential distortion measurements for a 15 deg clocked 40 probe rake indicated that the circumferential distortion levels are very sensitive to the symmetry of the flow and that a misalignment of the vanes in the experiment could have resulted in this difference. The numerical simulations of the BLI inlet with jets showed good agreement with the circumferential inlet distortion levels for a range of jet actuator mass flow ratios at a fixed inlet mass flow rate. The CFD simulations for the jet case also predicted an average total pressure recovery offset that was 0.01 lower than the experiment as was seen in the baseline. Comparisons of the flow features for the jet cases revealed that the CFD predicted a much larger vortex at the engine fan-face when compare to the experiment.

Allan, Brian G.↗
NASA NTRSDate not supplied

Streamline-Traced, External-Compression Supersonic Inlets for Mach 2

A computational study was performed to explore the aerodynamic design and performance of streamline-traced, external-compression (STEX) inlets for Mach 2.0. The performance metrics included inlet flow rates, total pressure recovery, and total pressure distortion. The study explored the use of round and flattened capture cross-sections and a bleed slot. The design of the inlet and generation of the inlet geometry was performed using the Supersonic Inlet Design and Analysis(SUPIN) Tool. Computational grids were generated, and methods of computational fluid dynamics (CFD) were applied to solve the three-dimensional, turbulent flow through the inlets using the Wind-US CFD flow solver. It was found that the use of a bleed slot with about 5% bleed resulted in an inlet total pressure recovery of 95% at Mach 2 with acceptable radial and circumferential total pressure distortion. It was also found that there was only a slight decrease in performance between a round and flattened capture cross-section. This suggests that the use of streamline tracing offers flexibility in shaping the inlet capture cross-section for a more favorable integration with an aircraft wing or fuselage. This flexibility and the good performance of the inlet provides a novel inlet design for future commercial supersonic aircraft.

Computational Fluid Dynamics↗
NASA NTRSDate not supplied

Streamline‐Traced, External‐Compression Supersonic Inlets for Mach 2

A computational study was performed to explore the aerodynamic design and performance of streamline-traced, external‐compression (STEX) inlets for Mach 2.0. The performance metrics included inlet flow rates, total pressure recovery, and total pressure distortion. The study explored the use of round and flattened capture cross‐sections and a bleed slot. The design of the inlet and generation of the inlet geometry was performed using the Supersonic Inlet Design and Analysis (SUPIN) Tool. Computational grids were generated, and methods of computational fluid dynamics (CFD) were applied to solve the three dimensional, turbulent flow through the inlets using the Wind‐US CFD flow solver. It was found that the use of a bleed slot with about 5% bleed resulted in an inlet total pressure recovery of 95% at Mach 2 with acceptable radial and circumferential total pressure distortion. It was also found that there was only a slight decrease in performance between a round and flattened capture cross‐section. This suggests that the use of streamline tracing offers flexibility in shaping the inlet capture cross‐section for a more favorable integration with an aircraft wing or fuselage. This flexibility and the good performance of the inlet provides a novel inlet design for future commercial supersonic aircraft.

Computational Fluid Dynamics↗