Search NASA⌕ Search

SEARCH · Search NASA

Results for “Polar oxide interface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Effects of oxidant gas for atomic layer deposition on crystal structure and fatigue of ferroelectric Hf x Zr 1-x O 2 thin films

TiN/Hf x Zr 1-x O 2 (HZO)/TiN capacitors were prepared using two types of HZO films fabricated by atomic layer deposition using H 2 O or O 2 plasma as an oxidant gas, and post-deposition annealing at 400 °C was performed before the TiN top-electrode fabrication. The ferroelectric orthorhombic phase was dominantly formed for the O 2 plasma-based capacitor due to the strongly oxidizing source of O 2 plasma, resulted in higher remanent polarization (2P r = 20 µC/cm 2 ) than that (13 µC/cm 2 ) of the H 2 O-based capacitor. The fatigue properties for the O 2 plasma-based capacitor were improved by 14 % after 106 cycles compared to the H 2 O-based capacitor. This could be attributed to an oxygen-rich interface reaction layer (IRL) including TiO x between the HZO film and TiN bottom-electrode for the O 2 plasma-based capacitor. In conclusion, based on these results, superior 2P r and fatigue properties can be obtained using O 2 plasma-based HZO films.

36 MATERIALS SCIENCE↗
NASA NTRS2000

Surfactant Facilitated Spreading of Aqueous Drops on Hydrophobic Surfaces

Microgravity technologies often require aqueous phases to spread over nonwetting hydrophobic solid/surfaces. At a hydrophobic surface, the air/hydrophobic solid tension is low, and the solid/aqueous tension is high. A large contact angle forms as the aqueous/air tension acts together with the solid/air tension to balance the large solid/aqueous tension. The aqueous phase, instead of spreading, is held in a meniscus by the large angle. Surfactants facilitate the wetting of water on hydrophobic surfaces by adsorbing on the water/air and hydrophobic solid/water interfaces and lowering the surface tensions of these interfaces. The tension reductions decrease the contact angle, which increases the equilibrium wetted area. Hydrocarbon surfactants (i.e. amphiphiles with a hydrophobic chain of methylene groups attached to a large polar group to give aqueous solubility) do not reduce significantly the contact angles of the very hydrophobic surfaces such as parafilm or polyethylene. Trisiloxane surfactants (amphiphiles with a hydrophobe consisting of methyl groups linked to a trisiloxane backbone in the form of a disk ((CH3)3-Si-O-Si-O-Si(CH3)3)) and an extended ethoxylate (-(OCH2CH2)n-) polar group in the form of a chain with seven or eight units) can significantly reduce the contact angle of water on a very hydrophobic surface and cause rapid and complete (or nearly complete) spreading (lermed superspreading). The overall goal of the research described in this proposal is to establish and verify a theory for how trisiloxanes cause superspreading, and then use this knowledge as a guide to developing more general hydrocarbon based surfactant systems which superspread and can be used in microgravity. We propose that the trisiloxane surfactants superspread when the siloxane adsorbs, the hydrophobic disk parts of the molecule adsorb onto the surface removing the surface water. Since the cross sectional area of the disk is larger than that of the extended ethoxylate chain, the disks can form a space filling mat on the surface which removes a significant amount of the surface water. The water adjacent to the hydrophobic solid surface is of high energy due to incomplete hydrogen bonding; its removal significantly lowers the tension and reduces the contact angle. Hydrocarbon surfactants cannot remove as much surface water because their large polar groups prevent the chains from cohering lengthwise. In our report last year we presented a poster describing the preparation of model very hydrophobic surfaces which are homogeneous and atomically smooth using self assembled monolayers of octadecyl trichlorosilane (OTS). In this poster we will use these surfaces as test substrates in developing hydrocarbon based surfactant systems which superspread. We studied a binary hydrocarbon surfactant systems consisting of a very soluble large polar group polyethylene oxide surfactant (C12E6 (CH3(CH2)11(OCH2CH2)6OH) and a long chain alcohol dodecanol. By mixing the alcohol with this soluble surfactant we have found that the contact angle of the mixed system on our test hydrophobic surfaces is very low. We hypothesize that the alcohol fills in the gaps between adjacent adsorbed chains of the large polar group surfactant. This filling in removes the surface water and effects the decrease in contact angle. We confirm this hypothesis by demonstrating that at the air/water interface the mixed layer forms condensed phases while the soluble large polar group surfactant by itself does not. We present drop impact experiments which demonstrate that the dodecanol/C12E6 mixture is effective in causing impacting drops to spread on the very hydrophobic model OTS surfaces.

Kumar, Nitin↗
DOE OSTI2025

Interfacial reconstruction effects in insulating double perovskite Nd2NiMnO6/SrTiO3 and Nd2NiMnO6/NdGaO3 thin films

Ferromagnetic insulating (FMI) double perovskite oxides (DPOs) A2BB′O6 with near-room-temperature Curie temperatures are promising candidates for ambient-temperature spintronics applications. To realize their potential, epitaxial stabilization of DPO films and understanding the effect of multiple broken symmetries across the film/substrate interface are crucial. This study investigates ultrathin films of the FMI Nd2NiMnO6 grown on SrTiO3 (STO) and NdGaO3 (NGO) substrates. By comparing growth on these substrates, we examine the influence of polarity and structural symmetry mismatches, which are absent in the NGO system. The interface exhibits immeasurable resistance in both cases. Using synchrotron x-ray diffraction, we show that films have three octahedral rotational domains because of the structural symmetry mismatch with the STO substrate. Furthermore, our coherent Bragg rod analysis of specular x-ray diffraction reveals a significant modification of the out-of-plane lattice parameter within a few unit cells at the film/substrate interface and the surface. This arises from polarity compensation and surface symmetry breaking, respectively. These structural alterations influence the Mn orbital symmetry, a dependence that we further confirm through x-ray linear dichroism measurements. Since the ferromagnetism in insulating DPOs is mediated by orbital-dependent superexchange interactions [Phys. Rev. Lett. 100, 186402 (2008)0031-900710.1103/PhysRevLett.100.186402], our study provides a framework for understanding the evolution of magnetism in ultrathin geometry.

Bhattacharya, Nandana↗
DOE OSTI2024

Nano-Plasticity of an Electrified Ionic Liquid/Electrode Interface: Uncovering Hard–Soft Structuring via Controlled Metal Fill Factor

Here, ionic liquids (ILs) nanostructuring at electrified interfaces is of both fundamental and practical interest as these materials are increasingly gaining prominence in energy storage and conversion processes. However, much remains unresolved about IL potential-controlled (re)organization under highly polarized interfaces, mostly due to the difficulty of selectively probing both the distal and proximal surface layers of adsorbed ions. In this work, the structural dynamics of the innermost layer (<10 nm from the surface) were independently interrogated from that of the ionic layers in the sub-surface region (>100 nm from the surface), using an infrared (IR) spectroscopy approach. By tuning the metal fill factor of gold films deposited on conductive metal oxide-modified IR internal reflection elements, the charge-driven (re)structuring of the inner and distal layers of 1-butyl-1-methylpyrrolidinium trifluoromethanesulfonate is unveiled. Within a relatively wide potential region (~±1 V) bounding the potential of zero charges, the ionic liquid is shown to undergo a reversible (i.e., soft) reorganization whereby the innermost layer of anions (cations) is exchanged by a layer of cations (anions). Kinetically unhindered changes in the number density of constituent cations and anions largely follow electrostatic expectations in the subsurface region, whereas the innermost layer exhibits a pronounced hysteresis and very slow relaxation. Under larger negative potential bias, IL restructuring is characterized by a highly irreversible (i.e., hard) and intense interfacial densification of the BMPy + cations, consistent with the formation of nanoscale segregated liquids. The outcomes of this work reveal a plastic IL nanostructuring under a strong electric field.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Feld-induced modulation of two-dimensional electron gas at LaAlO 3 /SrTiO 3 interface by polar distortion of LaAlO 3

Since the discovery of two-dimensional electron gas at the LaAlO 3 /SrTiO 3 interface, its intriguing physical properties have garnered significant interests for device applications. Yet, understanding its response to electrical stimuli remains incomplete. Our in-situ transmission electron microscopy analysis of a LaAlO 3 /SrTiO 3 two-dimensional electron gas device under electrical bias reveals key insights. Inline electron holography visualized the field-induced modulation of two-dimensional electron gas at the interface, while electron energy loss spectroscopy showed negligible electromigration of oxygen vacancies. Instead, atom-resolved imaging indicated that electric fields trigger polar distortion in the LaAlO 3 layer, affecting two-dimensional electron gas modulation. This study refutes the previously hypothesized role of oxygen vacancies, underscoring the lattice flexibility of LaAlO 3 and its varied polar distortions under electric fields as central to two-dimensional electron gas dynamics. These findings open pathways for advanced oxide nanoelectronics, exploiting the interplay of polar and nonpolar distortions in LaAlO 3 .

36 MATERIALS SCIENCE↗
DOE OSTI2022

Electrolyzer Performance Loss from Accelerated Stress Tests and Corresponding Changes to Catalyst Layers and Interfaces

Stress tests are developed for proton exchange membrane electrolyzers that utilize low catalyst loading, elevated potential, and frequent cycling with square- and triangle-waves to accelerate anode catalyst layer degradation during intermittent operation. Kinetics drive performance losses (ohmic/transport secondary) and are accompanied by decreasing exchange current density, decreasing cyclic voltammetric capacitance, and increasing polarization resistance. Decreased kinetics are likely due to a combination of iridium (Ir) migration into electrochemically inaccessible locations in the anode or membrane, Ir particle growth (supported by X-ray scattering), changes in the extent of the Ir oxidation state (supported by X-ray absorption spectroscopy), and anode catalyst layer reordering. Decreasing catalyst/transport layer contact and catalyst/membrane interfacial tearing may add contact resistances and account for increasing ohmic losses. Performance losses for low and moderate catalyst loading, as well as from accelerated and model wind/solar cycling protocols, were likewise dominated by kinetics but vary in severity. Additionally, accelerated cycling (1 cycle per minute) appears to reasonably accelerate relevant loss mechanisms and can be used to project electrolyzer lifetime from anode deterioration. Ongoing accelerated stress test development and studies into performance loss mechanisms will continue to be critical as electrolysis shifts to intermittent power and low-cost applications.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2020

Pitting behavior of friction stir repair-welded 304L stainless steel in 3.5% NaCl solution at room temperature: role of grain and defect structures

Stainless steel (SS) canisters used for storing spent nuclear waste are prone to chloride-induced stress corrosion cracking. Friction stir welding (FSW), being a low heat input process, can be used for repair welding of these canisters. In this study, an artificial crack was introduced on the 304L SS coupons by an electric discharge machining process. The artificial crack was repair-welded by FSW by maintaining the tool temperature a constant at two levels (725 and 825 °C). Friction stirring significantly reduced the grain size of the stirred zone (SZ) from about 47 to 2–4 μm. The fraction of low-angle grain boundaries increased in the SZ from 2 to 37–43%. Here, on the other hand, the fraction of special grain boundaries (Σ3 and Σ9) that was ~ 50% in the base metal reduced to < 10% in the SZ. During friction stirring, the oxide layer of artificial crack was broken and aligned to form a spiral defect called lazy-S structure. All these microstructural changes affected the corrosion behavior of the FSW specimens when tested in 3.5% NaCl at room temperature using cyclic polarization, chronoamperometry, and electrochemical impedance spectroscopy. The FSW specimens showed lower polarization resistance and lower transpassive potential than those of the base metal specimens. However, the pitting protection potentials of the FSW specimens were higher than that of the base metal. The pitting behavior of the FSW specimens was influenced more by the preferential attack on the lazy-S region than by passive film breakdown. The flat band potentials of the passive film formed on the FSW specimens were more positive than that of base metal. The charge carrier density of passive film formed on the FSW specimens was higher than that of the base metal. The higher fraction of low-angle grain boundaries present in the FSW specimens could supply more number of misorientation dislocations at the metal/film interface which could form anion vacancies by a climb process leading to formation of oxide at these locations without stressing the substrate. Therefore, low-angle boundaries are considered helpful for formation of stress-free passive films that will be highly stable and enhance both pitting and stress corrosion cracking resistance.

Dry storage canister↗
DOE OSTI2025

Polarization-Controlled Structural Modulation in the Single Atomic Layer at the PbZr 0.2 Ti 0.8 O 3 /LaNiO 3 Interface

Conductivity modulation via ferroelectric polarization coupling with LaNiO 3 (LNO) is demonstrated at an epitaxial ferroelectric–LNO interface. Conductivity measurements, varying the thickness of the LNO channel, show that this phenomenon is confined to a few atomic layers at the interface. Combining in situ biasing and off-axis holography, we mapped out electrostatic potentials at the PbZr 0.2 Ti 0.8 O 3 (PZT)/LNO/SrTiO 3 (STO) heterostructure upon polarization switching. Using aberration-corrected STEM, the interfacial atomic structures were investigated for the two different PZT polarization states. Polarization in PZT induces a significant change in the in-plane O–Ni–O bond angles, with a 37° modulation in the topmost 1 or 2 LNO unit cells, driven by strain in the oxygen sublattice for the two opposite polarization directions in PZT. Both oxygen and cation sublattices exhibit strain responses exceeding 10% upon switching. This atomic-layer structural modulation highlights a mechanism for functional oxide heterostructure development, offering pathways for advancements in nonvolatile memory, sensors, and energy-efficient transistors.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Controlling magnetism and transport at perovskite cobaltite interfaces via strain-tuned oxygen vacancy ordering

Complex oxides such as perovskite cobaltites exhibit rich phenomena at interfaces due to the complex interplay between their structural, defect, electronic, and magnetic degrees of freedom. Here, we study this interplay here in the ferromagnetic metallic cobaltite La 1−𝑥 ⁢Sr 𝑥⁢ CoO 3−𝛿 , using specific substrates to vary both the heteroepitaxial strain (compressive vs tensile) and growth orientation ((001) vs (110)). Transmission electron microscopy, electron energy-loss spectroscopy, high-resolution X-ray diffraction, magnetometry, polarized neutron reflectometry, and electronic magnetotransport measurements are applied. Lattice mismatch and growth orientation are found to enable the precise control of interfacial oxygen vacancy ordering in La 1−𝑥⁢ Sr 𝑥 ⁢CoO 3−𝛿 , thus dictating strain relaxation and oxygen vacancy depth profiles, in turn controlling thickness-dependent magnetic and electronic properties. In particular, compressive strain and (110) orientations minimize deleterious magnetic/electronic dead layer effects, leading to the optimization of interfacial magnetism and transport. Strain and orientation tuning of oxygen vacancy ordering are thus established as powerful means to control physical properties at cobaltite-based interfaces, relevant to several fields.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Interactions of Oxide Surfaces with Water Revealed with Solid-State NMR Spectroscopy

Hydrous materials are ubiquitous in the natural environment and efforts have previously been made to investigate the structures and dynamics of hydrated surfaces for their key roles in various chemical and physical applications, with the help of theoretical modeling and microscopy techniques. However, an overall atomic-scale understanding of the water–solid interface, including the effect of water on surface ions, is still lacking. Herein, we employ ceria nanorods with different amounts of water as an example and demonstrate a new approach to explore the water–surface interactions by using solid-state NMR in combination with density functional theory. NMR shifts and relaxation time analysis provide detailed information on the local structure of oxygen ions and the nature of water motion on the surface: the amount of molecularly adsorbed water decreases rapidly with increasing temperature (from room temperature to 150 °C), whereas hydroxyl groups are stable up to 150 °C, and dynamic water molecules are found to instantaneously coordinate to the surface oxygen ions. Additionally, the applicability of dynamic nuclear polarization for selective detection of surface oxygen species is also compared to conventional NMR with surface selective isotopic-labeling: the optimal method depends on the feasibility of enrichment and the concentration of protons in the sample. These results provide new insight into the interfacial structure of hydrated oxide nanostructures, which is important to improve performance for various applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Electrochemical cleaning: An in-Situ method to reverse chromium poisoning in solid oxide fuel cell cathodes

Chromium poisoning is one of the primary factors that affect solid oxide fuel cell (SOFC) durability. In this study, an electrochemical cleaning method has been employed to reverse the effects of chromium poisoning. Two cells were fabricated and poisoned under identical conditions by operating them at 800°C in the presence of a Cr source. Both poisoned cells exhibited a significant reduction in maximum power density and an increase in polarization resistance. One of the poisoned cells, designated as the baseline cell, was cooled to room temperature after poisoning. Microstructural observation of the baseline cell showed significant contamination of the cathode active layer by chromium oxide and (Cr,Mn) spinel deposits. The other poisoned cell was electrochemically cleaned for two hours under a mild electrolytic condition. As a result of the electrochemical cleaning process, the chromium oxide deposits were substantially removed leading to a significant reduction of Cr concentration in the cathode, especially at the cathode/electrolyte interface. Furthermore, a substantial fraction of the cell performance loss was also reversed. To the best of our knowledge, this is a first demonstration of reversing the effects of chromium poisoning using a rapid in-situ process.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2021

In situ study of the electronic structure of polar-to-polar SrTiO 3 /($000\bar1$)ZnO heterointerface

The SrTiO 3 (STO)/ZnO heterointerface, which is widely used in the fabrication of novel optoelectronic devices, is a classical system combining functional perovskite oxides and wurtzite-structure semiconductor materials. The electronic structure of the heterointerface often plays a significant role in controlling the functions of novel devices. In this study, the electronic structure was explored using in situ photoemission spectroscopy and X-ray absorption spectroscopy. X-ray diffraction results showed the coexistence of (111) STO and (011) STO orientations for the STO film deposited on the ZnO-($000\bar1$) substrate via pulsed laser deposition. High-resolution transmission electron microscopic results revealed two types of polar interfaces: [$11\bar2$][$10\bar1$](111) STO //[$1\bar210$][$10\bar10$]($000\bar1$) ZnO and [111][$2\bar1\bar1$](011) STO //[$10\bar21$][$10\bar10$]($000\bar1$)ZnO. In situ photoemission spectroscopic results revealed downward band bending and the transformation of the valence states of Ti from 4+ to 3+, with extra electrons transferring to the hybridization states between O 2p and Ti t 2g orbitals at the polar-to-polar STO/ZnO interface. We propose that the polar discontinuity drives the electron transfer to the STO/ZnO interface during the growth process. This study provides insight into the electronic structure of the STO/($000\bar1$)ZnO heterointerface.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2021

Ferroelectrics everywhere: Ferroelectricity in magnesium substituted zinc oxide thin films

We demonstrate ferroelectricity in Mg-substituted ZnO thin films with the wurtzite structure. Zn 1–x Mg x O films are grown by dual-cathode reactive magnetron sputtering on (111)-Pt // (0001)-Al 2 O 3 substrates at temperatures ranging from 26 to 200 °C for compositions spanning from x = 0 to x = 0.37. X-ray diffraction indicates a decrease in the c-lattice parameter and an increase in the a-lattice parameter with increasing Mg content, resulting in a nearly constant c/a axial ratio of 1.595 over this composition range. Transmission electron microscopy studies show abrupt interfaces between Zn 1–x Mg x O films and the Pt electrode. When prepared at pO 2 = 0.025, film surfaces are populated by abnormally oriented grains as measured by atomic force microscopy for Mg concentrations >29%. Raising pO 2 to 0.25 eliminates the misoriented grains. Optical measurements show increasing bandgap values with increasing Mg content. When prepared on a 200 °C substrate, films display ferroelectric switching with remanent polarizations exceeding 100 μC cm –2 and coercive fields below 3 MVcm –1 when the Mg content is between ~30% and ~7%. Substrate temperature can be lowered to ambient conditions, and when doing so, capacitor stacks show only minor sacrifices to crystal orientation and nearly identical remanent polarization values; however, coercive fields drop below 2 MV/cm. Using ambient temperature deposition, we demonstrate ferroelectric capacitor stacks integrated directly with polymer substrate surfaces.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Insight of BaCe 0.5 Fe 0.5 O 3– δ twin perovskite oxide composite for solid oxide electrochemical cells

One-pot synthesized twin perovskite oxide composite of BaCe 0.5 Fe 0.5 O 3–δ (BCF), comprising cubic and orthorhombic perovskite phases, shows triple-conducting properties for promising solid oxide electrochemical cells. Phase composition evolution of BCF under various conditions was systematically investigated, revealing that the cubic perovskite phase could be fully/partially reduced into the orthorhombic phase under certain conditions. The reduction happened between the two phases at the interface, leading to the microstructure change. As a result, the corresponding apparent conducting properties also changed due to the difference between predominant conduction properties for each phase. Based on the revealed phase composition, microstructure, and electrochemical properties changes, a deep understanding of BCF's application in different conditions (oxidizing atmospheres, reducing/oxidizing gradients, cathodic conditions, and anodic conditions) was achieved. Triple-conducting property (H + /O 2– /e – ), fast open-circuit voltage response (~16–~470 mV) for gradients change, and improved single-cell performance (~31% lower polarization resistance at 600°C) were comprehensively demonstrated. Besides, the performance was analyzed under anodic conditions, which showed that the microstructure and phase change significantly affected the anodic behavior.

08 HYDROGEN↗
DOE OSTI2026

Mechanism-Informed Breakdown: Understanding Degradation by Controlling Voltage-Hold Patterns in Proton Exchange Membrane Water Electrolyzers

Low catalyst loadings pose challenges to performance stability in proton exchange membrane (PEM) water electrolysis over extended operation. To study the impact of degradation mechanisms and voltage loss rates, different stress tests are applied to membrane electrode assemblies. Potential cycling conditions were observed to induce higher degrees of iridium (Ir) oxide crystallization, ionomer degradation, and catalyst layer (CL) thinning, which likely contributed to higher kinetic loss rates. On the other hand, while Ir migrating into the PEM (Ir band) generally impairs performance, the interconnected and more uniform Ir band formed under a constant 2 V hold may allow for Ir at the catalyst/membrane interface to remain electronically connected and kinetically accessible, as well as indicate greater Ir site access during the applied stressor. The 2 V hold also demonstrates improved kinetic durability through a lower Tafel slope, faster polarization kinetics, and reduced charge transfer resistance. In contrast, potential cycling caused the migration of disconnected Ir agglomerates into the membrane bulk and created a steady increase in charge transfer resistance, a more dramatic decrease in capacitance (46.7% loss), and significant damage to the surrounding ionomer, indicating a decline in both the quality and quantity of active sites in the anode CL. This work underscores the distinct degradation pathways associated with load holds versus cycling, highlighting the role of catalyst-ionomer interactions in kinetic performance and long-term stability. These insights can inform operational strategies for PEM electrolyzers powered by intermittent energy sources, aiming to minimize efficiency losses over extended operation.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Microstructural Underpinnings of Giant Intrinsic Exchange Bias in Epitaxial NiCo 2 O 4 Thin Films

Understanding intrinsic exchange bias in nominally single-component ferromagnetic or ferrimagnetic materials is crucial for simplifying related device architectures. However, the mechanisms behind this phenomenon and its tunability remain elusive, which hinders the efforts to achieve unidirectional magnetization for widespread applications. Inspired by the high tunability of ferrimagnetic inverse spinel NiCo 2 O 4 , the origin of intrinsic exchange bias in NiCo 2 O 4 (111) films deposited on Al 2 O 3 (0001) substrates are investigated. The comprehensive characterizations, including electron diffraction, X-ray reflectometry and spectroscopy, and polarized neutron reflectometry, reveal that intrinsic exchange bias in NiCo 2 O 4 (111)/Al 2 O 3 (0001) arises from a reconstructed antiferromagnetic rock-salt Ni x Co 1-x O layer at the interface between the film and the substrate due to a significant structural mismatch. Remarkably, by engineering the interfacial structure under optimal growth conditions, it can achieve exchange bias larger than coercivity, leading to unidirectional magnetization. Such giant intrinsic exchange bias can be utilized for realistic device applications. This work establishes a new material platform based on NiCo 2 O 4 , an emergent spintronics material, to study tunable interfacial magnetic and spintronic properties.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Integrated process-structure–property–performance optimization of cold-sprayed zinc coatings on AZ91 magnesium alloy

High-pressure die cast (HPDC) AZ91 magnesium alloy is widely used in automotive components such as transmission housings and brackets for its excellent strength-to-weight ratio. Zinc-based cold spray coatings can be applied selectively to vulnerable areas to enhance corrosion resistance, minimize galvanic coupling with dissimilar metals, and eliminate the need for full-surface oxide coatings, making the process more efficient and targeted. A comprehensive evaluation of 16 combinations of nitrogen carrier gas temperatures and pressures led to the identification of an optimal range of process parameters, yielding Zn coatings with porosity <0.5 % by area, wear rates reduced by a factor of two compared to uncoated AZ91, and adhesion strengths up to 35 MPa. The enhanced mechanical performance of the coating is attributed to the low porosity and the formation of a metallurgical bond at the coating-substrate interface. Corrosion studies using macroscale potentiodynamic polarization (PDP) and electrochemical impedance spectroscopy (EIS) revealed a significant decrease in corrosion rate and a shift to more noble corrosion potentials (ZCP) for coated substrates. Furthermore, the Zn cold-sprayed samples exhibited significantly lower corrosion-induced evolved hydrogen content compared to the base AZ91 substrate and AZ91 coated with industrial coatings, demonstrating that the Zn layer effectively protects the substrate from the corrosive environment. Overall, cold spray Zn coatings significantly improve the mechanical and corrosion performance of AZ91 Mg alloys, addressing key material challenges and enabling their broader use in automotive applications.

Corrosion performance↗
DOE OSTI2021

On the characteristics of N-polar GaN Schottky barrier contacts with LPCVD SiN interlayers

In this work, we study the behavior of N-polar GaN Schottky diodes with low-pressure chemical vapor deposited (LPCVD) SiN interlayers and unveil the important role of an amphoteric miniband formed in this interlayer due to a previously identified and dominating Si dangling bond defect. Through analysis of temperature-dependent current–voltage (I–V–T), capacitance–voltage (C–V), and x-ray photoelectron spectroscopy measurements, we observe that when nickel is deposited on LPCVD SiN pretreated with hydrofluoric acid, the SiN/GaN interface is responsible for determining the overall system's barrier height. By contrast, contact formation on oxidized LPCVD SiN leads to a metal/SiN-dominant barrier. We, consequently, propose band diagrams that account for an amphoteric miniband in LPCVD SiN, leading to a new understanding of LPCVD SiN as a lossy dielectric with surface barrier-dependent behavior.

42 ENGINEERING↗