Search NASA⌕ Search

SEARCH · Search NASA

Results for “Polyethylene Glycols”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Polyester-based epoxy vitrimer integrating spent coffee ground as a natural filler

Coffee is a widely consumed beverage, but approximately 80% mass of coffee cherry is discarded as waste. Here, in this study, spent coffee grounds (SCG) were recycled and used as a natural filler in a polyester-based epoxy matrix made from reactions of diglycidyl ethers of Bisphenol A and polyethylene glycol with methyl nadic anhydride. The properties of SCG/epoxy composites with various SCG contents up to 40% w/w were evaluated using various techniques such as FT-IR spectroscopy, tensile testing, optical microscopy, differential scanning calorimetry, and rheology. The SCG filled polyester-based epoxy matrix demonstrated excellent dimensional stability and retained a permanently crosslinked network, but re-shaping was possible at ~150 °C through transesterification, which occurred due to a dynamic chain exchange reaction between the ester group of the epoxy matrix and the hydroxyl group of the SCG fillers. The transesterification also improved the interfacial adhesion between the matrix and SCG fillers, resulting in tensile strength of over 20 MPa and a modulus of around 2.5 GPa, even with high SCG contents up to 40% w/w. While neat, cured epoxy shows thermoset behavior, filling the matrix with SCG enables reforming and origami-inspired spontaneous change in shape.

42 ENGINEERING↗
DOE OSTI2021

Electrolyte effects on the electrochemical performance of microemulsions

Here, we report a study of the electrochemistry of Ferrocene (Fc) in a Tween®20 (polyethylene glycol (20) sorbitan monolaurate) /1-butanol/ water/Toluene (TBWT) microemulsion system, focusing on the effects of electrolyte components. Resistance and conductivity measurements are used along with Cyclic Voltammetry (CV) to characterize the effects of supporting electrolyte, such as Bu 4 NBF 4 and KNO 3 , on the electrochemical performance and transport properties of Fc. With increasing Fc-containing oil phase concentration in the microemulsion, the observed peak current density fails to increase proportionately with the Fc concentration. Adding 0.05 m Bu 4 NBF 4 in the oil phase significantly increases the current density, presumably by lowering the resistance of microemulsion and promoting the accessibility of Fc in the system. Moreover, increasing the aqueous phase supporting electrolyte from 0.5 m KNO 3 to 1 m KNO 3 does not exhibit an analogous effect. We discuss these results in the context of our working hypothesis for microemulsion organization and its implications for electron transfer to Fc.

Conductivity↗
DOE OSTI2022

Pectin methyltransferase QUASIMODO2 functions in the formation of seed coat mucilage in Arabidopsis

Pectin, cellulose, and hemicelluloses are major components of primary cell walls in plants. In addition to cell adhesion and expansion, pectin plays a central role in seed mucilage. Seed mucilage contains abundant pectic rhamnogalacturonan-I (RG-I) and lower amounts of homogalacturonan (HG), cellulose, and hemicelluloses. Previously, accumulated evidence has addressed the role of pectin RG-I in mucilage production and adherence. However, less is known about the function of pectin HG in seed coat mucilage formation. In this study, we analyzed a novel mutant, designated things fall apart2 (tfa2), which contains a mutation in HG methyltransferase QUASIMODO2 (QUA2). Etiolated tfa2 seedlings display short hypocotyls and adhesion defects similar to qua2 and tumorous shoot development2 (tsd2) alleles, and show seed mucilage defects. Here, the diminished uronic acid content and methylesterification degree of HG in mutant seed mucilage indicate the role of HG in the formation of seed mucilage. Cellulosic rays in mutant mucilage are collapsed. The epidermal cells of seed coat in tfa2 and tsd2 display deformed columellae and reduced radial wall thickness. Under polyethylene glycol treatment, seeds from these three mutant alleles exhibit reduced germination rates. Together, these data emphasize the requirement of pectic HG biosynthesis for the synthesis of seed mucilage, and the functions of different pectin domains together with cellulose in regulating its formation, expansion, and release.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

Insights into determining pore size properties of ultrafiltration membranes

The selectivity of porous membranes is often characterized using solute rejection tests, where membranes are challenged with dilute aqueous solutions of neutral solutes at operating conditions that minimize concentration polarization and fouling. In single solute tests, a membrane is challenged with one molecular weight (MW) solute at a time from low to high MW. Since single solute methods are time-intensive, mixed solute tests have become more common, where a mixture of several MW solutes challenges a membrane at once. However, the presence of large solutes in a mixture increases the rejection of smaller solutes. Furthermore, there are no universally accepted operating conditions or standard methods used by membrane manufacturers or researchers for the experiments, leading to difficulty in pore size and pore characteristic comparisons. In this paper, commercial ultrafiltration membranes were challenged with single and mixed solute polyethylene glycol (PEG) and dextran aqueous solutions. First, rejection values determined using total organic carbon (TOC) and high-performance liquid chromatography (HPLC) from single solute filtration experiments are compared. Differences in rejection curves obtained by the two techniques are attributed to solute polydispersity. Mixed solute filtration experiments with binary mixtures of solutes showcased co-solute interactions, which increase with both the size and weight percent of large solute in the mixture. Mixed solute filtration experiments at varying operating conditions (i.e., stir speed and flux) were conducted to determine operating conditions that mitigate co-solute interactions. Stir speed had a minimal effect on co-solute interactions. In contrast, low flux conditions can help minimize co-solute interactions, leading to pore size distributions that closely resemble results observed in single solute filtration using narrowly dispersed solutes. Additionally, at low flux conditions, the predicted membrane pore size distributions utilizing mixed solute experiments with PEG and dextran were similar.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Wood template-supported phase change material composites for durable and form-stable thermal energy storage in buildings

Here, to reduce and shift peak energy loads in buildings, phase change materials (PCMs) with high transition enthalpies and transition temperatures near human thermal comfort are desirable for thermal energy storage (TES). Traditional solid/liquid PCMs suffer from leakage during thermal cycling, requiring encapsulation that lowers heat storage capacity. Wood templates (WTs), with porous and hierarchical structures, provide natural encapsulation scaffolds for PCM containment. Polyethylene glycol (PEG) is a compatible PCM with WTs, but when infiltrated alone, ~30 wt% of PEG binds to wood with no detectable phase change, limiting TES efficiency. To address this, we developed a method to (1) improve the form stability of balsa and pine-based composites (BWT + PCMs and PWT + PCMs) and (2) reduce inactive PCM within the composites to ~10 wt%. BWT + PCMs exhibit transition properties upwards of 114.2 J/g at 25.4 degrees C, with no degradation after 1000 thermal cycles, and similar stiffness compared to raw balsa. Meanwhile, PWT + PCMs exhibit 25 % higher storage efficiency with the addition of poly(ethylene glycol) diacrylate compared to solely PEG-infiltrated PWT. PWT + PCM retains 84 % of raw pine's mechanical stiffness, sufficient for light-duty construction. Our shape-stabilized WT + PCM composites enrich the functionality of wood materials as both ideal TES material candidates and light-duty building construction applications.

25 ENERGY STORAGE↗
DOE OSTI2021

Striking luminescence phenomena of carbon dots and their applications as a double ratiometric fluorescence probes for H2S detection

Here, we report some new observations on the luminescence of carbon dots (CDs) that are passivated with polyethylene glycol, and explored them, for the first time, as highly sensitive H2S detection probe. The as-prepared CDs have an ultraviolet (UV) emission at 350 nm and a green emission at 540 nm when excited at 270 nm, but they have only a green emission at 523 nm when excited at 365 nm. As Na2S is added to the CDs, the UV emission decreases gradually, while the green emission increases slightly, and interestingly a new emission appears at 455 nm is increased linearly in intensity with the increase of Na2S concentration. The blue emission at 455 nm is from the intrinsic core of CDs, and the green emissions at 540 or 523 nm are from their surface states, while the UV emission at 350 nm is from the anchored PEG. Both the emission intensity ratios of F-450/F-350 and F-455/F-523 show an excellent linear relationship with the Na2S concentration in the range of 0-800 mu M, and the detection limit estimated from both of them is approximately 7.0 nM, indicating our method is the most sensitive H2S CDs based detection method reported thus far. Furthermore, the detection was tested successfully for H2S imaging in live cells. We propose that the interactions of H2S with the CDs and the anchored ligands, as well as the energy transfer between the ligands and the CDs, are responsible for the luminescence responses for H2S detection. Our studies enrich the world of carbon dots with plenty of potential applications. (C) 2020 Elsevier Ltd. All rights reserved.

Bioimaging↗
DOE OSTI2020

Creation of a High-Yield AAV Vector Production Platform in Suspension Cells Using a Design-of-Experiment Approach

Recombinant adeno-associated virus (rAAV) vectors are a leading gene delivery platform, but vector manufacturing remains a challenge. New methods are needed to increase rAAV yields and reduce costs. Past efforts to improve rAAV production have focused on optimizing a single variable at a time, but this approach does not account for the interactions of multiple factors that contribute to vector generation. Here, we utilized a design-of-experiment (DOE) methodology to optimize rAAV production in a HEK293T suspension cell system. We simultaneously varied the transgene, packaging, and helper plasmid ratios, the total DNA concentration, and the cell density to systematically evaluate the impact of each variable across 52 conditions. The results revealed a unique set of parameters with a lower concentration of transgene plasmid, a higher concentration of packaging plasmid, and a higher cell density than previously described protocols. Using this DOE-optimized protocol, we achieved unpurified yields approaching 3 × 10 14 viral genomes (VGs)/L of cell culture. Additionally, we incorporated polyethylene glycol (PEG)-based virus precipitation, pH-mediated protein removal, and affinity chromatography to our downstream processing, enabling average purified yields of >1 × 10 14 VGs/L for rAAV-EGFPs across 13 serotypes and capsid variants.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Thermally stable and self-healable lignin-based polyester

The increased use of plastics and the associated environmental impact has catalyzed research on the development of bio-derived polymers. Bio-based polyesters have gained increased attention due to the abundance of their starting materials and ease of processing. Lignin is naturally occurring in biomass with rich carbon content, whose functionality and rigidity make it an ideal bio-derived candidate for bio-based polyesters. Herein, a lignin-based polyester with good thermal stability and self-repairability was synthesized from carboxylated lignin and epoxidized soybean oil. The synthesized lignin/epoxidized soybean oil (ESO) vitrimer was brittle such that its mechanical performance could not be recorded. However, when polyethylene glycol (PEG) was incorporated as a plasticizer, polymer samples exhibited acceptable ductility. From thermomechanical analysis of the synthesized polyesters, the plasticizer did not impair thermal stability of polymers, but greatly enhanced mechanical properties. Notably, all samples exhibited stability at high temperatures, and good glass transition temperatures (51.0 ± 0.9–78.0 ± 1.2 °C). The highest tensile strength (3.983 ± 0.1 MPa) and storage modulus (1463.67 ± 12.6 MPa) were recorded for the polyester containing 6 % w/w PEG. Moreover, the polymer samples exhibited self-healing capability at 180 °C. This work expands on valorization of lignin through the synthesis of bio-derived materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

3D printed polymer gaskets for custom-form batteries

Additive manufacturing (AM) processes, like 3D printing, help to facilitate complex and customizable battery geometries which can provide design freedom and enhance volumetric energy density within electronic devices. AM materials must have the thermal and mechanical properties that enable printability, and when used in batteries, AM materials must also be chemically and electrochemically compatible with the battery chemistry. The compatibility between AM materials and the battery is of particular importance for the cell packaging materials which must be inert and are often overlooked. This study systematically studies AM-compatible polymeric materials for use as gaskets in lithium-ion cells. The materials investigated include three thermoplastics suitable for material extrusion printing: polylactic acid (PLA), polycarbonate, and polypropylene/polyethylene copolymer (PPPEC); and two photoresins suitable for vat photopolymerization (VPP) printing: an acrylate-based photoresin and a polyethylene glycol diacrylate photoresin. The AM gasket materials were tested in comparison to a conventional commercial polypropylene gasket. Mechanical testing (swell measurements and material stiffness) and electrochemical testing (linear sweep voltammetry and galvanostatic cycling of full cells) demonstrated that PLA and the VPP polymers were the least compatible with the lithium-ion battery chemistry, despite their prevalent use in studies of AM batteries, and that PPPEC was the most compatible.

3D printing↗
DOE OSTI2023

Solid-state polymer magnesium supercapacitor

Here, the present article focuses on the development of a highly ion-conductive, solvent-free, solid-state polymer electrolyte membrane (PEM) via photopolymerization of polyethylene glycol diacrylate (PEGDA) network from its homogeneous melt mixtures containing succinonitrile (SCN) plasticizer and magnesium bis(trifluoromethane sulfonyl) imide Mg(TFSI) 2 salt. The above solid-state Mg-PEM exhibits a Helmholtz electric double-layer capacitor (EDLC) behavior in its supercapacitive symmetric carbonaceous electrode configuration. The electrochemical stability for this PEM membrane (20/40/40 PEGDA/SCN/Mg (TFSI) 2 ) was found to be approximately 3 V from linear sweep voltammetry with a specific capacitance of about 44 F/g from cyclic voltammetry and an energy density of approximately 17 Wh/kg in the 0–2 V range from the constant current density (CCD) experiment. Of particular interest is its excellent capacity retention of over 11,200 cycles, thus tested with the Coulombic efficiency of over 87%. Moreover, the energy density after extensive cycling for 11,200 has increased to approximately 56 Wh/kg at 10 mV/s in the potential range of 0–3 V relative to 17 Wh/kg in the potential range of 0–2 V at the same scan rate, attesting the excellent electrochemical stability and long life of the present Mg-PEM supercapacitor.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Glass-fiber-reinforced polymeric film as an efficient protecting layer for stable Li metal electrodes

With numerous reports on protecting films for stable lithium (Li) metal electrodes, the key attributes for how to construct these efficient layers have rarely been fully investigated. Here, we report a rationally designed hybrid protective layer (HPL) with each component aligning with one key attribute; i.e., cross-linked poly(dimethylsiloxane) (PDMS) enhances flexibility, polyethylene glycol (PEG) provides homogeneous ion-conducting channels, and glass fiber (GF) affords mechanical robustness. A significant improvement of the electrochemical performance of HPL-modified electrodes can be achieved in Li/HPL@Cu half cells, HPL@Li/HPL@Li symmetric cells, and HPL@Li/LiFePO 4 full cells. Even with an industrial standard LiFePO 4 cathode (96.8 wt % active material), the assembled cell still exhibits a capacity retention of 90% after 100 cycles at 1 C. More importantly, the functionality of each component has been studied comprehensively via electrochemical and physical experiments and simulations, which will provide useful guidance on how to construct efficient protective layers for next-generation energy storage devices.

25 ENERGY STORAGE↗
DOE OSTI2021

Dynamic tunability of phase-change material transition temperatures using ions for thermal energy storage

Thermal energy storage (TES) based on phase-change materials (PCMs) has many current and potential applications, such as climate control in buildings, thermal management for batteries and electronics, thermal textiles, and transportation of pharmaceuticals. Despite its promise, the adoption of TES has been limited, in part due to limited tunability of the transition temperature, which hinders TES performance for varying use temperatures. Transition temperature tuning of a material using an external stimulus, such as pressure or an electric field, typically requires very large stimuli. To circumvent this problem, here, we report on the dynamic transition temperature tunability of a PCM using ions. We achieve a transition temperature tunability up to 6°C in polyethylene glycol (PEG) by using the salt lithium oxalatodifluoroborate at a low voltage of 2.5 V, which may enable simpler and safer devices/system designs. We also explain the thermal properties of the salt/PCM solution using the Flory-Huggins theory.

25 ENERGY STORAGE↗
DOE OSTI2026

Surface Crust Formation Controls Evaporation Kinetics of Secondary Organic Aerosols

Gas-particle partitioning is critical for the evolution of secondary organic aerosols (SOA) in the atmosphere. SOA particles evaporate more slowly than expected at nearly size-independent rates, but the underlying mechanism remains controversial. Here, in this study, we apply kinetic multilayer modeling to simulate evaporation of α-pinene SOA, demonstrating that surface crust formation, emerging from accumulation of low-volatility compounds at the particle surface, leads to slow evaporation and reduced size dependence of the evaporation rate. While evaporation induced by decomposition of oligomers would naturally lead to size-independent evaporation rates, we observe and simulate nearly size-independent slow evaporation of polyethylene glycol mixture particles containing polymeric species that do not decompose, confirming the relevance of composition-dependent diffusivity for size-independent, slow evaporation. Slow evaporation of limonene SOA was also observed in environmental chamber experiments, and model simulations demonstrate strong surface crust formation with bulk diffusivity being depressed by up to 5 orders of magnitude compared to the inner bulk. We present experimental evidence using a surface-based mass spectrometry technique that shows that the particle surface becomes enriched in high molecular weight compounds upon evaporation of monomers. Our findings imply that viscous surface crusts may also limit the growth and chemical transformation of SOA particles, influencing their impacts on air quality and climate.

heterogeneous chemistry↗
DOE OSTI2020

Macromolecular Crowding Affects Voltage-Dependent Alamethicin Pore Formation in Lipid Bilayer Membranes

Macromolecular crowding is known to modulate chemical equilibria, reaction rates, and molecular binding events, both in aqueous solutions and at lipid bilayer membranes, natural barriers that enclose the crowded environments of cells and their subcellular compartments. Previous studies on the effects of macromolecular crowding in aqueous compartments on conduction through membranes have focused on single-channel ionic conduction through previously formed pores at thermodynamic equilibrium. Furthermore, the effects of macromolecular crowding on the mechanism of pore formation itself were studied using the droplet interface bilayer (DIB) technique with the voltage-dependent pore-forming peptide alamethicin (alm). Macromolecular crowding was varied using 8 kDa molecular weight polyethylene glycol (PEG8k) or 500 kDa dextran (DEX500k) in two aqueous droplets on both sides of the bilayer membrane. In general, voltage thresholds for pore formation in the presence of crowders in the droplets decreased compared to their values in the absence of crowders, due to excluded volume effects, water binding by PEG, and changes in the ordering of water molecules and hydrogen-bonding interactions involving the polar lipid headgroups. In addition, asymmetric crowder loading (e.g., PEG8k–DEX500k on either side of the membrane) resulted in transmembrane osmotic pressure gradients that either enhanced or degraded the ionic conduction through the pores.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Effect of Polymer Chain Length on the Superlattice Assembly of Functionalized Gold Nanoparticles

We report on the assembly of gold nanoparticle (AuNPs) superlattices at the liquid/vapor interface and in the bulk of their suspensions. Interparticle distances in the assemblies are achieved on multiple length scales by varying chain lengths of surface grafted AuNPs by polyethylene glycol (PEG) with molecular weights in the range 2000–40,000 Da. Crystal structures and lattice constants in both 2D and 3D assemblies are determined by synchrotron-based surface-sensitive and small-angle X-ray scattering. Here, assuming knowledge of grafting density, we show that experimentally determined interparticle distances are adequately modeled by spherical brushes close to the θ point (Flory–Huggins parameter, x ≈ 1/2) for 2D superlattices at a liquid interface and a nonsolvent (χ = ∞) for the 3D dry superlattices.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Binding of Cholera Toxin B-Subunit to a Ganglioside GM1-Functionalized PEG-Tethered Lipid Membrane

We report neutron reflectometry (NR) studies of polyethylene glycol (PEG)-tethered model lipid membranes at the solid–liquid interface and of cholera toxin’s B-subunit (CTxB) binding to tethered membranes containing ganglioside GM1 receptors. First, tethered polymer brushes were formed by grafting silane-functionalized PEG lipopolymers to quartz from solution. Subsequent deposition of lipids by Langmuir–Blodgett/Langmuir–Schaefer (LB/LS) resulted in a tethered bilayer structure separated from the solid support by a hydrated PEG layer. NR revealed that the tethers formed a highly hydrated polymer brush, uniformly separating the bilayer from the underlying solid substrate. Further, the lipid bilayer did not significantly perturb the brush’s conformation relative to a free brush. Biological functionality of the tethered bilayers was verified by interacting CTxB, with ganglioside GM1 receptors incorporated into the bilayer. The surface coverage of CTxB bound to the lipid membrane, θ CTB = 0.58 ± 0.08, was consistent with the coverage predicted for random sequential absorption, and toxin binding did not impact the membrane conformation.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Interaction of Planar Brushes with End-Functionalized Carboxylic or Amine Groups: Water Structure, Hydrogen Bonds, and Electrostatic Correlations

In this work we present a detailed analysis of two parallel plates grafted with polyethylene glycol (PEG) terminated with carboxylic or amine groups, and discuss the cases of opposite and same charge in the presence of electrolytes. We analyze the screening of charged groups by electrolytes, the role of hydrogen bonds in enhancing attraction or repulsion, hydration forces, competitive binding with counterions, and the hydrogen bond network, crucial to stabilizing the system. Our simulations reveal that, for large plate separation, the system is well described as a “Stern layer”, characterized by strong counterion binding and a subsequent weak diffuse layer. For short plate separation, the system is characterized by strong correlations among end groups and counterions. We also discuss the relevance of charged carboxylic/amine groups in different problems with a particular emphasis on nanoparticle assembly.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Using Nanofiller Assemblies to Control the Crystallization Kinetics of High-Density Polyethylene

Polyethylene-grafted nanoparticles (NPs) are organized into a variety of assemblies in a polydisperse polyethylene melt by tailoring the graft density and molecular weights of the graft chains. Under these conditions we systematically vary NP assemble state and study is consequences on crystal nucleation and growth rates. We find that the nucleation rate is suppressed below that of the unfilled polymer for good NP spatial dispersion. However, poorer dispersion, which leads to the formation of NP assemblies, can accelerate nucleation likely by providing multiple heterogenous sites due to topographical features. We find that a key parameter, the chain overcrowding in the brush, can predict these nucleation trends – in this language, the most enhanced nucleation rate is found when the grafts are the most overcrowded, and hence the least interpenetrated with the matrix chains. This result is consistent with one other literature result which utilized short crystallizable polyethylene glycol grafts in short PEO matrices. The growth kinetics were retarded for all nanocomposites, their temperature dependences were essentially equal to that for the pure polymer (in the absence of NPs) – the NPs thus do not affect secondary nucleation, indicating that the transport of the matrix to the growth front is the rate determining step. Thus, evidently the increase in matrix viscosity, or reduction in growth rates, is directly determined by the agglomeration state of the NPs. These results are consistent with past works with bare silica NPs in PEO, and with silica NPs grafted with amorphous chains in a PEO matrix, suggesting that growth kinetics in these systems apparently follow “universal” behavior. Additionally, there are initial hints that the ratio of the effective surface area of the NP clusters per unit matrix volume provides a unified description of the NP induced confinement that slows growth kinetics. Furthermore, our work thus shows that there is an evolving understanding of the role of NPs on crystallization kinetics, in particular crystal growth where trends appear to be independent of the grafts ability to crystallize.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗