Search NASA⌕ Search

SEARCH · Search NASA

Results for “Porous structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Molecular Scale Tuning of Covalent Organic Frameworks for Enhanced Properties

Covalent organic frameworks (COFs) are a type of porous, extended structure material which has demonstrated utility in numerous applications, including sensing and separations. Judicious choice of the linker and node not only fine tune the size of the framework, but also the functionality. We seek to tailor COF materials for applications in gas capture and electrochemical sensing. Herein, we demonstrate the material properties of COFs can be fine-tuned via post-synthetic metal cation doping of the parent structures. We have synthesized several COF structures with varying linkers which allow for the incorporation of metal cations. Structures incorporating Zn 2+ , Mn 2+ , and Cu 2+ have demonstrated utility in improving the CO 2 uptake properties of the COFs, while Ag + doped structures show potential as electrochemical sensors for chloride anions.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Using low cost, bio-derived and recycled materials in advanced scalable small- and medium- wind turbine manufacturing

In partnership with Bergey Windpower, this project explored the use of recyclable and recycled materials in small- to medium-wind turbine blades (WTBs). A recyclable epoxy resin and infusible thermoplastic resin were investigated using identical fiber reinforcements and manufacturing practices used as Bergey, and the substitution of continuous virgin glass fiber (GF) layers with recycled nonwoven GF (rGF, NW) mats was trialed. The alternative resins both showed very promising performance in terms of static tensile and flexural behavior as well as thermal properties and fatigue behavior in comparison with that of the incumbent materials used at Bergey. The NW rGF materials, however, were found to be a poor substitute for the continuous GF materials for two primary reasons. Firstly, the NW mats took up significantly more resin than their continuous counterparts, which would increase both the weight and the cost of the WTBs. Additionally, an unexpected reaction occurred between the rGF and epoxy materials that resulted in a highly porous, foamed structure. The foaming phenomenon was not observed with the rGF NW and infusible thermoplastic material, but the resin uptake was still prohibitively high. Based on the results of this study, recyclable infusible resins could be viable candidate materials for Bergey in the future. The foaming reaction with the rGF NW mats could prove highly useful in other applications requiring structural foams and has been used to produce demonstrative sandwich panels.

17 WIND ENERGY↗
DOE OSTI2025

Holistic Microstructure Control Strategies in Photopolymerization‐Induced Phase Separation of Acrylate Systems

Open porous materials, known for their large surface area and interconnected structures, are essential in various applications, including batteries, ion exchange, catalysis, filtration, and electronic waste recycling. A critical aspect of the functionality of porous membranes is the precise control of pore size and morphology. Photopolymerization-induced phase separation (photo-PIPS) offers a convenient and versatile methods for creating porous structures. However, controlling the porous morphology remains challenging due to the complex interplay between thermodynamics, polymerization kinetics, and monomer structures, which makes it difficult to establish the relationship between processing conditions and resulting morphology in photo-PIPS. Herein, a physics-based phase-field model capable of generating and characterizing the microstructures of porous materials based on both average and localized features is developed. Using the phase-field simulations as test bed, the effects of polarity, light intensity, and curing temperature, as well as the previously unexplored roles of chain transfer agents and substrates, on the morphology of the resulting porous microstructure are investigated. Experiments are performed to verify the results predicted by the simulations. This work lays out a comprehensive guide for designing PIPS-derived porous microstructures and offers practical engineering strategies for tailoring microstructure-level topology and size of pores for application-specific needs.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Applying a Compact Porous Media Model to Numerically Derive Resistance Coefficients for Lattice Structures

Additive Manufacturing allows for exploring various geometries to achieve specific engineering criteria. Lattices are one geometry with unique properties, including being periodically repeating structures which allow flow through them to be represented as a porous media according to Darcy-Forchheimer equations. These equation’s coefficients are generally experimentally derived, but this work demonstrates the ability to numerically derive them with CFD. Simulations were performed using three-dimensional stead state Reynolds-averaged Navier-Stokes with a k-ω Shear Stress Transport turbulence model using Ansys Fluent. Three lattice geometries were investigated and drag coefficients were derived. The method was validated against externally published data for similar geometries demonstrating strong agreement, and grid convergence for all simulations was calculated with a Grid Convergence Index method. Wall roughness is demonstrated to have a non-negligible impact on results and roughness values are considered for the primary focus Octahedral geometry where both smooth wall and rough wall coefficients were derived. The porosity coefficients for the Octahedral geometry at 1.0 [m/s] were found to be 2.89×10 6 and 2.90×10 6 [1/(Pa*m*s)] for the permeability coefficients, 6.37×10 1 and 5.44×10 1 [m 2 /kg] for the inertial resistance coefficients, and with a max pressure drop of 5116.7 [Pa] and 4429.5 [Pa] for the smooth walls and rough walls, respectively. The derived numerical method enables rapid exploration and optimization of new lattice designs for diverse engineering applications.

42 ENGINEERING↗
DOE OSTI2024

Aging of Limestones and Silane–Siloxane-Based Protective Hydrophobics: The Impact of Heating–Cooling and Freeze–Thaw Cycles

Stones are traditionally used in construction and architectural applications as building elements due to their aesthetic and technical/structural performance. Like other environmental factors (rain, humidity, moisture, salt presence, biological activity, etc.), heating–cooling and freeze–thaw cycles significantly threaten the longevity of stone materials. Hence, considering the socio-economic and cultural value of stones, preventive actions such as hydrophobic coatings are applied to prevent or mitigate damage. The scope of this study is the performance assessment of limestones with different characteristics and the efficiency of various commercial silane/siloxane-based hydrophobic coatings when exposed to thermal variation and freeze–thaw. For that purpose, the standards EN 14066:2013 (determination of resistance to aging by thermal shock) and EN 12371:2010 (determination of frost resistance) were followed. Open porosity and static contact angles were estimated to assess the stone durability and water protection capabilities of the hydrophobics. Additionally, sound speed propagation velocity, quality of building material index, elastic modulus and flexural strength were measured to evaluate the variation of mechanical properties. Static contact angle revealed that the coatings maintained an efficient level of hydrophobicity even after thermal-shock and freeze–thaw weathering tests. The study also revealed a critical interaction between freeze–thaw cycles, hydrophobic coatings and structural integrity of the stones, mostly on more porous ones. When they are subjected to harsh environmental conditions, untreated porous limestones keep structural cohesion, allowing for the natural absorption and release of water during freezing and thawing. On the contrary, when limestones are treated, the hydrophobic coatings can moderately obstruct the water release due to the partial saturation of the porous framework by the products. It also probably resulted from the different mechanical behavior between the inner matrix and layer of stone coated, resulting in a premature breakout and mechanical damage of the stone.

Lisci, Carla (ORCID:000000032179130X)↗
DOE OSTI2024

Full-field quantitative visualization of shock-driven pore collapse and failure modes in PMMA

The dynamic collapse of pores under shock loading is thought to be directly related to hot spot generation and material failure, which is critical to the performance of porous energetic and structural materials. However, the shock compression response of porous materials at the local, individual pore scale is not well understood. This study examines, quantitatively, the collapse phenomenon of a single spherical void in PMMA at shock stresses ranging from 0.4 to 1.0 GPa. Using a newly developed internal digital image correlation technique in conjunction with plate impact experiments, full-field quantitative deformation measurements are conducted in the material surrounding the collapsing pore for the first time. The experimental results reveal two failure mode transitions as shock stress is increased: (i) the first in situ evidence of shear localization via adiabatic shear banding and (ii) dynamic fracture initiation at the pore surface. Numerical simulations using thermo-viscoplastic dynamic finite element analysis provide insights into the formation of adiabatic shear bands (ASBs) and stresses at which failure mode transitions occur. Further numerical and theoretical modeling indicates the dynamic fracture to occur along the weakened material inside an adiabatic shear band. Finally, analysis of the evolution of pore asymmetry and models for ASB spacing elucidate the mechanisms for the shear band initiation sites, and elastostatic theory explains the experimentally observed ASB and fracture paths based on the directions of maximum shear.

42 ENGINEERING↗
DOE OSTI2025

3D Printing of Highly Porous Polypropylene Separators for Lithium‐Ion Batteries Using Fused Deposition Modeling and Thermally Induced Phase Separation

Appearing as one of the key-components of lithium-ion batteries (LIBs), this work specifically focuses on the additive manufacturing (AM) of custom-shape separators, facilitated by the filament material extrusion process, also called fused deposition modeling (FDM). The development and optimization of composite thermoplastic filament feedstocks combining polypropylene and paraffin wax, followed by the 3D printing of the separator membranes is shown. A post-processing step, based on thermal induced phase separation (TIPS), is introduced to promote porosity formation through removal of the paraffin wax sacrificial phase within the 3D printed items. Separators with different polypropylene/paraffin wax ratios are developed and the impact on printability, mechanical strength, porosity, and electrochemical performances, is thoroughly discussed. X-ray micro-computed tomography is employed to assess the geometric fidelity and to detect printing defects in a complex 3D lattice structure. The performance of the 3D printed porous separators is also compared to a commercial separator. This pioneering research establishes a foundation for the creation of porous separators that can adapt to and conform into 3D printed battery architectures with novel form factors, and also creates opportunities for the use of FDM and TIPS for a wide range of applications that employ porous structures beyond the energy storage field.

3D printing↗
DOE OSTI2025

Manufacturing Li 2 TiO 3 -based tritium breeder materials by volume-controlled spark plasma sintering with an optimized microstructure

Multifunctional ceramic breeder materials are highly desirable for the deuterium-tritium fusion to achieve high efficiency in breeding tritium through neutron irradiation of lithium-containing blankets. Li 2 TiO 3 displays unique attributes as a potential ceramic breeder material. An optimized microstructure with three-dimensional interconnected pore structure is required for rapid transport of the tritium for effective fuel cycle, which however enviably results in the degradation of the thermal-mechanical properties of the breeding materials. In this work, nanocrystalline porous Li 2 TiO 3 ceramic pellets with controlled porosities of 14% and 20% are manufactured by volume-controlled spark plasma sintering. An optimized 3D interconnected pore structure is achieved consisting of both micro-sized pores and nano-sized pores embedded in nanocrystalline matrix, which could be beneficial to facilitate easy removal of bred T and He. Further, the 3D interconnected porous structure is well maintained upon isothermal annealing of the SPS-fabricated pellets at relevant operation temperature of the solid breeding materials. Single-phasic porous pellets also display enhanced thermal-mechanical properties, superior to current state-of-the-art materials which establish their potential as a promising tritium breeder material for nuclear fusion applications.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Sulfur Conversion to Donor‐Acceptor Ladder Polymer Networks through Mechanochemical Nucleophilic Aromatic Substitution for Efficient CO 2 Photoreduction

The development of synthetic methods capable of converting elemental sulfur into conjugated porous sulfur‐rich polymers remains a great challenge, although direct utilization of this readily available feedstock can significantly enrich its uses and circumvent environmental problems during sulfur storage. Here, we report herein mechanochemical (MC) nucleophilic aromatic substitution (S N Ar) that enables sulfur conversion into thianthrene‐bridged porous ladder polymer networks with dense donor‐acceptor (D−A) molecular junctions. We demonstrate that the key lies in the generation of bent thianthrene units through a solid‐state ball‐milling condensation reaction between 1,2‐dihaloarenes and elemental sulfur. We also show that the assembling of D−A structural motifs into porous networks affords efficient visible‐light‐driven photocatalytic reduction of carbon dioxide (CO 2 ) with water (H 2 O) vapor, in the absence of any additional photosensitizer, sacrificial agents or cocatalysts. Exceptional photoinduced charge separation along with boosted exciton dissociation results in a high‐performance of carbon monoxide (CO) production rate of 306.1 μmol g −1 h −1 with near 100 % CO selectivity, which is accompanied by H 2 O oxidation to O 2 , as confirmed by both experimental and theoretical results. We anticipate this novel MC S N Ar approach will advance processing techniques for direct sulfur utilization and facilitate new possibilities for the synthesis of D−A ladder polymer networks with promising potential in photocatalysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Porous mesh manifold for enhanced boiling performance

High-performance electronics are continuously demanding cooling of higher heat fluxes. Phase-change cooling, including pool boiling, is a useful approach to address this challenge; however, competition between liquid and vapor flows generally limit the heat fluxes that can be dissipated. A range of strategies to control these flows have been investigated previously, including capillary guides. Here a manifold structure formed from a metallic mesh is investigated to control the disposition of liquid and vapor phases above a pool fed boiling surface enhanced with porous structures. Copper mesh forms defined liquid flow paths, using capillary action to guide and distribute liquid evenly over the heated surface, along with open channels to facilitate vapor escape. The mesh provides a novel structure for liquid guidance that imposes low resistance to liquid flow while occluding a minimal area of heated surface underneath. The manifold performance is characterized in boiling fed by a pool of water above a laser-textured aluminum nitride heat dissipation surface with pin–fin structures having heights of 110 µm and spacing of 30 µm with a heated area of 5 mm x 5 mm. A maximum heat flux of 490 W/cm 2 is reached with the manifold in the pool fed configuration, representing an increase of more than 65% over the porous pin fin surface alone. The maximum stable superheat observed for the manifold of 36K is 14K higher than that for the porous surface without the manifold. The factors limiting performance of the manifold are analyzed. High superheat is attributed to partial flooding of the boiling surface as suggested by the reduction in superheat using external suction. Similar systems and structures for enhanced two-phase cooling are compared.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Extending TOUGH + HYDRATE with a parallel particle transport simulator: numerical investigation of sand production during gas production from hydrate deposits

A new parallel code for simulating particle transport in porous media is integrated with the TOUGH + HYDRATE simulator to investigate sand production associated with gas production from unconsolidated gas hydrate-bearing sediments (HBS). Here, the parallel coupled simulator is named THMPT and uses the integral finite difference method to describe the Darcian and non-Darcian flow of fluids and heat transport, the finite element method to describe the associated geomechanical changes, and the discrete element method to track the trajectory of individual sand particles within the HBS. The THMPT simulator is written in Fortran, incorporates multiple optimized algorithms, and can comprehensively address the coupled flow, thermal, chemical, geomechanical, and particle transport processes that characterize the system behaviors during gas production from HBS. The simulator can capture all processes involved in sand particle transport in porous media, including sand detachment, collision, clogging (i.e., bridging), and migration. A benchmark case study of sand production in the course of depressurization-induced gas production from a representative HBS reveals various distinct microscopic particle migration mechanisms and the adverse impact of sand particle detachment, transport, and clogging. The numerical investigation also examines the effect of bottomhole pressure on mitigating sand production. The simulation results indicate that sand clogging near the wellbore significantly reduces permeability, decreasing gas production by at least 50%. Lastly, the efficiency of gravel packing in mitigating sand production is numerically evaluated, revealing that the structure of the porous media appears to profoundly influence the macroscopic motion behavior of sand particles and sand clogging characteristics.

discrete element method↗
DOE OSTI2025

Scaled-up fabrication of durable and porous adsorbent-coated minichannels on aluminum for CO 2 separation

A method was developed to fabricate zeolite 13X adsorbent-coated minichannels on aluminum for CO₂ adsorption applications in this study. It emphasizes the innovative use of aluminum as a substrate, which offers airtight assembly, paving the way for highly efficient adsorption systems. An optimized coating process was developed using a slurry of Zeolite 13X, yeast, sugar, and xanthan gum, resulting in durable and highly porous layers that enhance CO₂ capture performance. A PETG peeler was designed to remove the top layer of the yeast-engineered adsorbent coatings, revealing a super porous and foamy structure. The teeth of the peeler were designed and fabricated for high repeatability and rapid prototyping. Breakthrough experiments were conducted on the scaled-up adsorbent bed using gas mixtures of 80% CO₂, 20% N₂, and 20% CO₂, 80% N₂ to represent different industrial scenarios. The performance of the bed was evaluated at flow rates of 160 and 190 cm³ min -1 using a Raman Laser Gas Analyzer (RLGA), demonstrating stable adsorption without degradation across multiple cycles. Computational modeling of integral transport phenomena under the chosen experimental conditions was pursued using gPROMS ProcessBuilder™, and the modeling results were compared with those from the tests for adsorption time, which resulted in an error margin of 2% to 9% for the breakthrough time, confirming the easy reproducibility of the design through modeling. This research advances CO₂ capture technologies by providing an effective and scalable solution for producing aluminum-based adsorbent coated beds, supporting industrial carbon capture efforts.

CO2 capture↗
DOE OSTI2025

Graphite crystals in catalytically-graphitized glass-like carbon

Catalytic graphitization of glass-like carbon leads to enhanced growth of micro-sized graphitic crystals with unusual shapes of wires, filaments, tubes, rods, whiskers, and spirals. Similar particles with axial symmetry are also found in pure glass-like carbon heat-treated at high temperatures. Nonetheless, the presence of a graphitization catalyst, Si in this case, in the heat-treatment process supports the transformation of porous, disordered carbon structure towards the graphitic atomic order and the formation of manifold peculiar polyhedral wires and particles of geometry distinct from the plate-like shape typical for conventional graphite. In contrast to conventional carbon nanotubes and fibers, the graphene layers are stacked perpendicular to the tube axis, while the size of the most common tube fibers can reach up to 10 μm in diameter and 100 μm in length. X-ray diffraction, Raman spectroscopy, scanning and transmission electron microscopy, small-angle X-ray scattering combined with complementary techniques have been used to characterize the structure of the glass-like carbon derived from furfuryl alcohol catalytically-graphitized using Si particles at 3000 °C. Finally, since control of graphite shape is vital to achieving the level of performance required in contemporary applications, the obtained results demonstrate that the catalytic graphitization method may be employed to produce filamentous graphite crystals.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Wood template-supported phase change material composites for durable and form-stable thermal energy storage in buildings

Here, to reduce and shift peak energy loads in buildings, phase change materials (PCMs) with high transition enthalpies and transition temperatures near human thermal comfort are desirable for thermal energy storage (TES). Traditional solid/liquid PCMs suffer from leakage during thermal cycling, requiring encapsulation that lowers heat storage capacity. Wood templates (WTs), with porous and hierarchical structures, provide natural encapsulation scaffolds for PCM containment. Polyethylene glycol (PEG) is a compatible PCM with WTs, but when infiltrated alone, ~30 wt% of PEG binds to wood with no detectable phase change, limiting TES efficiency. To address this, we developed a method to (1) improve the form stability of balsa and pine-based composites (BWT + PCMs and PWT + PCMs) and (2) reduce inactive PCM within the composites to ~10 wt%. BWT + PCMs exhibit transition properties upwards of 114.2 J/g at 25.4 degrees C, with no degradation after 1000 thermal cycles, and similar stiffness compared to raw balsa. Meanwhile, PWT + PCMs exhibit 25 % higher storage efficiency with the addition of poly(ethylene glycol) diacrylate compared to solely PEG-infiltrated PWT. PWT + PCM retains 84 % of raw pine's mechanical stiffness, sufficient for light-duty construction. Our shape-stabilized WT + PCM composites enrich the functionality of wood materials as both ideal TES material candidates and light-duty building construction applications.

25 ENERGY STORAGE↗
DOE OSTI2024

Measurement of the Static Nonlinear Third-Order Elastic Moduli of Rocks: Problems and Applicability

The third-order elastic (TOE) model has been used to describe the widely observed nonlinear mechanical behaviors of earth materials. In addition to linear elastic constants ( λ , μ ), three nonlinear elastic moduli ( A , B , C ) are required for isotropic rocks. Contrary to previous research on dynamic TOE moduli, this study followed the protocol to measure strain and stress under uniaxial and hydrostatic compressive tests statically, which were later used to invert for the full set of TOE moduli for four standard rock types with differing pore structures of a porous oolitic limestone, quartz-rich sandstones, and a dense crystalline basalt. The applicability of the TOE model to characterize nonlinearity depends on the fulfillment of path-independence and small-strain assumptions. Using the measured static TOE moduli, the finite element model demonstrates that the stress in the vicinity of the wellbore is more amplified than the stress in the linear elastic case, which leads to a wider zone of rock failure around the wellbore. Due to the long-standing discrepancy between static and dynamic moduli, the rarely reported full set of static TOE moduli is necessary and will benefit future research in understanding the effect of rock nonlinearity on geophysical and geomechanical applications, such as long-term safe storage of CO 2 and generating process of geohazards.

58 GEOSCIENCES↗
DOE OSTI2025

Tailoring multi-dimensional hierarchical self-assembly of metallacages through balancing non-covalent interactions

Despite advances in non-covalent interactions and complex self-assembly, precise control of multi-dimensional hierarchical self-assembly (HSA) from the molecular level to larger scales remains challenging. Herein, we designed and synthesized two rigid tetratopic ligands with multiple preset driving forces, and assembled them with Zn(II) ions to obtain metallacages SC6 and SC12 . Through balancing multiple non-covalent interactions, including metal–organic coordination, hydrophobic, and π–π interactions, SC6 can hierarchically self-assemble driven by a poor solvent, from one-dimensional nanowires to super-helical nanostructures via non-equilibrium self-assembly, progressing continuously with time and the increasing proportion of the poor solvent. However, for SC12 with enhanced hydrophobic interactions, two-dimensional monolayer nanogrids were formed by hierarchical self-assembly. Notably, these structures can be recycled back to primary metallacages through simple dissolution, highlighting their potential for efficient recycling and reuse. These results demonstrate that multi-dimensional hierarchical structures enable precise construction by balancing non-covalent interactions through a bottom-up self-assembly approach. This study provides deeper insight into the mechanisms of HSA and a promising strategy for the tailored creation of complex structures and sustainable porous materials.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Exploitation of Pore Structure for Increased CO 2 Selectivity in Type 3 Porous Liquids

CO 2 capture requires materials with high adsorption selectivity and an industrial ease of implementation. To address these needs, a new class of porous materials was recently developed that combines the fluidity of solvents with the porosity of solids. Type 3 porous liquids (PLs) composed of solvents and metal–organic frameworks (MOFs) offer a promising alternative to current liquid carbon capture methods due to the inherent tunability of the nanoporous MOFs. However, the effects of MOF structural features and solvent properties on CO 2 –MOF interactions within PLs are not well understood. Herein experimental and computational data of CO 2 gas adsorption isotherms were used to elucidate both solvent and pore structure influences on ZIF-based PLs. The roles of the pore structure including solvent size exclusion, structural environment, and MOF porosity on PL CO 2 uptake were examined. A comparison of the pore structure and pore aperture was performed using ZIF-8, ZIF-L, and amorphous-ZIF-8. Adsorption experiments here have verified our previously proposed solvent size design principle for ZIF-based PLs (1.8× ZIF pore aperture). Furthermore, the CO 2 adsorption isotherms of the ZIF-based PLs indicated that judicious selection of the pore environment allows for an increase in CO 2 selectivity greater than expected from the individual PL components or their combination. This nonlinear increase in the CO 2 selectivity is an emergent behavior resulting from the complex mixture of components specific to the ZIF-L + 2'-hydroxyacetophenone-based PL.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

A General Approach for Metal Nanoparticle Encapsulation Within Porous Oxides

Abstract Encapsulation of metal nanoparticles within oxide materials has been shown as an effective strategy to improve activity, selectivity, and stability in several catalytic applications. Several approaches have been proposed to encapsulate nanoparticles, such as forming core‐shell structures, growing ordered structures (zeolites or metal‐organic frameworks) on nanoparticles, or directly depositing support materials on nanoparticles. Here, a general nanocasting method is demonstrated that can produce diverse encapsulated metal@oxide structures with different compositions (Pt, Pd, Rh) and multiple types of oxides (Al 2 O 3 , Al 2 O 3 ‐CeO 2 , ZrO 2 , ZnZrO x , In 2 O 3 , Mn 2 O 3 , TiO 2 ) while controlling the size and dispersion of nanoparticles and the porous structure of the oxide. Metal@polymer structures are first prepared, and then the oxide precursor is infiltrated into such structures and the resulting material is calcined to form the metal@oxide structures. Most Pt@oxides catalysts show similar catalytic activity, demonstrating the availability of surface Pt sites in the encapsulated structures. However, the Pt@Mn 2 O 3 sample showed much higher CO oxidation activity, while also being stable under aging conditions. This work demonstrated a robust nanocasting method to synthesize metal@oxide structures, which can be utilized in catalysis to finely tune metal‐oxide interfaces.

Zhou, Chengshuang↗