Search NASA⌕ Search

SEARCH · Search NASA

Results for “Pressure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Comparison of Real-Time Pressure Rail Selection Algorithms for the Hybrid Hydraulic Electric Architecture: Case Study on a Track Loader

Abstract The hybrid hydraulic electric architecture (HHEA) seeks to combine the high power/torque/force density of hydraulics with the efficiency of electric machines. A set of common pressure rails is used to provide a majority of the power and this power is modulated by small electric machines to provide precise control for the operator. The HHEA has been studied in previous work using off-line dynamic programming optimization to determine energy efficient pressure rail selections, but this approach requires drive cycle information apriori. A Lagrange multiplier method has also been investigated where a set of gains (Lagrange multipliers) are optimized off-line with the idea the these gains, once determined, could be used for real-time operation. In this work, three new real-time pressure rail selection algorithms that do not require future drive cycle information are investigated; greedy, torque minimizing, and thresholding. The greedy control is found to only use 1% more energy than the globally optimal dynamic programming solution; but a model of energy loss is required.

24 POWER TRANSMISSION AND DISTRIBUTION↗
NASA NTRS1972

Dynamic response of high-frequency pressure transducers to large amplitude sinusoidal pressure oscillations

Dynamic response characteristics of six currently used dynamic pressure transducers were investigated by using a large-amplitude sinusoidal-pressure generator. Frequencies between 1 and 15 kilohertz with corresponding peak-to-peak pressure-oscillation amplitudes ranging between 73 and 8 percent of bias pressure and bias pressures between 15 and 300 psia were utilized. Amplitude-ratio data as functions of frequency and pressure level are given for all transducers. The generator design and performance and associated instrumentation are described.

Robinson, R. E.↗
NASA NTRS1974

Computer programs for pressurization (RAMP) and pressurized expulsion from a cryogenic liquid propellant tank

An analysis to predict the pressurant gas requirements for the discharge of cryogenic liquid propellants from storage tanks is presented, along with an algorithm and two computer programs. One program deals with the pressurization (ramp) phase of bringing the propellant tank up to its operating pressure. The method of analysis involves a numerical solution of the temperature and velocity functions for the tank ullage at a discrete set of points in time and space. The input requirements of the program are the initial ullage conditions, the initial temperature and pressure of the pressurant gas, and the time for the expulsion or the ramp. Computations are performed which determine the heat transfer between the ullage gas and the tank wall. Heat transfer to the liquid interface and to the hardware components may be included in the analysis. The program output includes predictions of mass of pressurant required, total energy transfer, and wall and ullage temperatures. The analysis, the algorithm, a complete description of input and output, and the FORTRAN 4 program listings are presented. Sample cases are included to illustrate use of the programs.

Masters, P. A.↗
NASA NTRS1977

High-pressure cryogenic seals for pressure vessels

This investigation of the problems associated with reliably containing gaseous helium pressurized to 1530 bars (22 500 psi) between 4.2 K and 150 K led to the following conclusions: (1) common seal designs used in existing elevated-temperature pressure vessels are unsuitable for high-pressure cryogenic operation, (2) extrusion seal-ring materials such as Teflon, tin, and lead are not good seal materials for cryogenic high-pressure operation; and (3) several high-pressure cryogenic seal systems suitable for large-pressure vessel applications were developed; two seals required prepressurization, and one seal functioned repeatedly without any prepressurization. These designs used indium seal rings, brass or 304 stainless-steel anvil rings, and two O-rings of silicone rubber or Kel-F.

Buggele, A. E.↗
NASA NTRS1983

Portable dynamic pressure generator for static and dynamic calibration of in situ pressure transducers

A portable dynamic pressure generator was developed to meet the requirements of determining the dynamic sensitivities of in situ pressure transducers at low frequencies. The device is designed to operate in a frequency range of 0 to 100 Hz, although it was only tested up to 30 Hz, and to generate dynamic pressures up to 13.8 kPa (2 psi). A description of the operating characteristics and instrumentation used for pressure, frequency, and displacement measurements is given. The pressure generator was used to statically and dynamically calibrate transducers. Test results demonstrated that a difference an exist between the static and dynamic sensitivity of a transducer, confirming the need for dynamic calibrations of in situ pressure transducers.

Bolt, P. A.↗
NASA NTRS1986

A model for the influence of pressure on the bulk modulus and the influence of temperature on the solidification pressure for liquid lubricants

Two pressure chambers, for compression experiments with liquids from zero to 2.2 GPa pressure, are described. The experimentally measured compressions are then compared to theoretical values given by an isothermal model of equation of state recently introduced for solids. The model describes the pressure and bulk modulus as a function of compression for different types of lubricants with a very high accuracy up to the pressure limit of the high pressure chamber used (2.2 GPa). In addition the influence of temperature on static solidification pressure was found to be a simple function of the thermal expansion of the fluid.

Jacobson, B. O.↗
NASA NTRS1987

A model for the influence of pressure on the bulk modulus and the influence of temperature on the solidification pressure for liquid lubricants

Two pressure chambers, for compression experiments with liquids from zero to 2.2 GPa pressure, are described. The experimentally measured compressions are then compared to theoretical values given by an isothermal model of equation of state recently introduced for solids. The model describes the pressure and bulk modulus as a function of compression for different types of lubricants with a very high accuracy up to the pressure limit of the high pressure chamber used (2.2 GPa). In addition the influence of temperature on static solidification pressure was found to be a simple function of the thermal expansion of the fluid.

Jacobson, Bo O.↗
NASA NTRS1993

An automated pressure data acquisition system for evaluation of pressure sensitive paint chemistries

An automated pressure data acquisition system for testing of pressure sensitive phosphorescent paints was designed, assembled, and tested. The purpose of the calibration system is the evaluation and selection of pressure sensitive paint chemistries that could be used to obtain global aerodynamic pressure distribution measurements. The test apparatus and setup used for pressure sensitive paint characterizations is described. The pressure calibrations, thermal sensitivity effects, and photodegradation properties are discussed.

Sealey, Bradley S.↗
NASA NTRS1994

Experimental measurements and analytical analysis related to gas turbine heat transfer. Part 1: Time-averaged heat-flux and surface-pressure measurements on the vanes and blades of the SSME fuel-side turbine and comparison with prediction. Part 2: Phase-resolved surface-pressure and heat-flux measurements on the first blade of the SSME fuel-side turbine

Time averaged Stanton number and surface-pressure distributions are reported for the first-stage vane row, the first stage blade row, and the second stage vane row of the Rocketdyne Space Shuttle Main Engine two-stage fuel-side turbine. Unsteady pressure envelope measurements for the first blade are also reported. These measurements were made at 10 percent, 50 percent, and 90 percent span on both the pressure and suction surfaces of the first stage components. Additional Stanton number measurements were made on the first stage blade platform blade tip, and shroud, and at 50 percent span on the second vane. A shock tube was used as a short duration source of heated and pressurized air to which the turbine was subjected. Platinum thin-film heat flux gages were used to obtain the heat flux measurements, while miniature silicon-diaphragm flush-mounted pressure transducers were used to obtain the pressure measurements. The first stage vane Stanton number distributions are compared with predictions obtained using a version of STAN5 and a quasi-3D Navier-Stokes solution. This same quasi-3D N-S code was also used to obtain predictions for the first blade and the second vane.

Source record↗
NASA NTRS1998

Rotor Blade Pressure Measurement in a Rotating Machinery Using Pressure and Temperature Sensitive Paints

Pressure and temperature sensitive paints have been utilized for the measurement of blade surface pressure and temperature distributions in a high speed axial compressor and an Allied Signal F109 gas turbine engine. Alternate blades were painted with temperature sensitive paints and then pressure sensitive paint. This combination allows temperature distributions to be accounted for when determining the blade suction surface pressure distribution. Measurements were taken and pressure maps on the suction surface of a blade were obtained over a range of rotational speeds. Pressure maps of the suction surface show-strong shock waves at the higher speeds.

Torgerson, S.↗
NASA NTRSDate not supplied

Adaptive Pressure Profile Method to Locate the Isolator Shock Train Leading Edge Given Limited Pressure Information

To maximize the performance of high-speed air-breathing engines, such as dual-mode scramjets, the streamwise location of the shock train leading edge (STLE) is ideally placed as far upstream in the isolator as possible while avoiding engine unstart. Thus, it is of interest to quantify and control the STLE location as the vehicle travels along its flight trajectory. The STLE location is typically quantified using wall static pressure measurements but there are often restrictions on the number and placement of transducers, thus reducing the accuracy and overall capability of STLE detection methods. In this work, the Adaptive Pressure Profile (APP) method is introduced to address such sparsity concerns. This method is data driven and does not heavily rely on prior information about the flow regime or engine model. Instead, the \mname method uses real-time pressure measurements from a small number of transducers to adaptively learn the isolator pressure profile. This adaptively-learned profile is fit to the pressure data at each time instance to estimate STLE location. The \mname method produces accurate estimates even when (1) the STLE location is not bounded by two or more transducers or (2) when the STLE location is between two transducers that are situated several duct heights apart. Data from two direct-connect isolator models are used to evaluate the accuracy of the \mname method and demonstrate its robustness for different back-pressure scenarios and transducer configurations.

Robin L Hunt↗
NASA NTRSDate not supplied

Adaptive Pressure Profile Method to Locate the Isolator Shock Train Leading Edge Given Limited Pressure Information

To maximize the performance of high-speed air-breathing engines, such as dual-mode scramjets, the streamwise location of the shock train leading edge (STLE) is ideally placed as far upstream in the isolator as possible while avoiding engine unstart. Thus, it is of interest to quantify and control the STLE location as the vehicle travels along its flight trajectory. The STLE location is typically quantified using wall static pressure measurements but there are often restrictions on the number and placement of transducers, thus reducing the accuracy and overall capability of STLE detection methods. In this work, the Adaptive Pressure Profile (APP) method is introduced to address such sparsity concerns. This method is data driven and does not heavily rely on prior information about the flow regime or engine model. Instead, the \mname method uses real-time pressure measurements from a small number of transducers to adaptively learn the isolator pressure profile. This adaptively-learned profile is fit to the pressure data at each time instance to estimate STLE location. The \mname method produces accurate estimates even when (1) the STLE location is not bounded by two or more transducers or (2) when the STLE location is between two transducers that are situated several duct heights apart. Data from two direct-connect isolator models are used to evaluate the accuracy of the \mname method and demonstrate its robustness for different back-pressure scenarios and transducer configurations.

Robin Hunt↗
NASA NTRS2021

Automated Technique for the Detection of Step-Like Solar Wind Dynamic Pressure Changes: Application to the Response of the Transpolar Potential to Solar Wind Dynamic Pressure Fronts

The input from the solar wind (SW) and the accompanying Interplanetary Magnetic Field (IMF) is the defining feature of the solar wind-magnetosphere interactions. One of the most important SW drivers is the solar wind dynamic pressure, and most significantly its sharp changes known as pressure fronts. Sudden enhancements in solar wind dynamic pressure, SWP, have been shown to lead to intensification of the auroral electrojets (and Region 1 field-aligned currents), increase in auroral emissions, and significant enhancement in ionospheric convection and the transpolar potential. Case studies of the interaction between pressure fronts and the terrestrial space environment shed great light on their importance to the structure and dynamics of the system. However, thorough understanding of the interaction requires fully statistical investigations. These statistical studies require a large number of suitable pressure front events. In the past these have been obtained through laborious manual inspection of solar wind data. We present an automated procedure that identifies sudden step enhancements in SWP that satisfy a desired set of limiting step-like characteristics, such as magnitude of the change, sign of the change (positive/negative), and rate of change. The procedure yields a list of suitable events, along with their step features within minutes. The technique is tested for missed events and false positives by direct comparison to manual inspection of the data. Its utility is illustrated by application to the statistical effect of pressure fronts to the transpolar potential as measured by the Assimilative Mapping of Ionospheric Electrodynamics (AMIE) technique.

A. Boudouridis↗
DOE OSTI2024

A Model to Account for the Effects of Load Ratio and Hydrogen Pressure on the Fatigue Crack Growth Behavior of Pressure Vessel Steels

A phenomenological model for estimating the effects of load ratio R and hydrogen pressure P H2 on the hydrogen-assisted fatigue crack growth rate (HA–FCGR) behavior in the transient and steady-state regimes of pressure vessel steels is described. The “transient regime” is identified with crack growth within a severely embrittled zone of intense plasticity at the crack tip. The “steady-state” behavior is associated with the crack growing into a region of comparatively lower hydrogen concentration located further away from the crack tip. The model treats the effects of R and P H2 as being functionally separable. In the transient regime, the effects of the hydrogen pressure on the HA–FCGR behavior were negligible but were significant in the steady-state regime. The hydrogen concentration in the steady-state region is modeled as being dependent on the kinetics of lattice diffusion, which is sensitive to pressure. Experimental HA–FCGR data from the literature were used to validate the model. The new model was shown to be valid over a wide range of conditions that ranged between –1 ≤ R ≤ 0.8 and 0.02 ≤ P H2 ≤ 103 MPa for pressure vessel steels.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

Spectral Analysis of Integrated Pressures on Patches with Unsteady Pressure-Sensitive Paint Measurements

This paper describes the spectral analysis of integrated pressures on patches of the scale model of the Space Launch System Block 1 cargo vehicle with the Unsteady Pressure-Sensitive Paint measurements, which were collected in the ascent transient aerodynamics test with the Unitary Plan Wind Tunnel 11-by-11-foot Transonic Wind Tunnel in September 2019 at NASA Ames Research Center. The patches are defined with x station values, indicating the position along length of the vehicle, and azimuth angles of the scale model. For each patch, the polygons are determined from the surface cells of the grid of the model, clipped with the edges of the patch, and each of the polygons is divided into triangles. The integrated pressure of the patch is determined as the ratio of the sum of the forces on the triangles over the sum of the areas of the triangles. For each run of the test, the cross power spectral density and magnitude squared coherence are computed from the time series of the integrated pressures on the patches. The results of pressure integration and spectral analysis are presented, and the data consistency of the test is demonstrated. The work described in this paper is a part of NASA’s development of a new state-of-the-art uPSP capability in production wind tunnels. Funding for this research was provided by the NASA Aeroscience Evaluation and Test Capabilities Project.

Pressure-Sensitive Paint↗
NASA NTRSDate not supplied

Methodology for Validation of Unsteady Pressure-Sensitive Paint Measurements using Pressure Transducers

Unsteady Pressure-Sensitive Paint (uPSP) technology provides simultaneously high-frequency and high-spatial resolution surface pressure fluctuation measurements. It has demonstrated value in wind tunnel test facilities to evaluate aerospace vehicle unsteady aerodynamics. The calibration of measurements from digital pixel counts into corresponding physical units relies on both lab-based and in-situ calibration steps, and its validation is both challenging and critical to adoption of the technology. We present a rigorous methodology for direct comparison of uPSP-derived surface pressure measurements to reference pressure transducer data based on a model of the camera-based measurement error, a model of the flow field pressure signal, and their propagation through the uPSP data reduction algorithm. The methodology is demonstrated on data collected in a small-scale, subsonic wind tunnel test as well as data collected from a Space Launch System unsteady aerodynamics characterization test at the NASA Ames Research Center Unitary Plan Wind Tunnel Complex.

Pressure-Sensitive Paint↗
NASA NTRSDate not supplied

Degradation Characterization of Unsteady Pressure-Sensitive Paint Under Various Pressures

The lifetime and intensity techniques are two distinct methods used to measure the surface pressure of wind tunnel models with pressure-sensitive paint (PSP). When exposed to 405 nm light for extended periods, both the luminescence and the lifetime ratio were observed to decrease, affecting perceived pressure values. To help further the implementation of the uPSP, this paper describes the efforts to characterize the degradation of both the intensity of the paint and its lifetime ratio, as well as the change in intensity calibration. It was found that the paint degrades at different rates depending on the partial pressure of oxygen during excitation. It was also found that the calibration curves exhibit greater changes when under higher oxygen concentrations, both indicating photodegradation due to photodecomposition and photo-oxidation processes. These effects are observed on models in a subsonic 14” × 14” wind tunnel. The work provides insight into the dynamic degradation behavior of PSP and uPSP, paving the way to reduce the error in pressure measurements obtained through these techniques.

Pressure-Sensitive Paint↗
NASA NTRS1971

Miniature pressure valve for on-board calibration of pressure transducers.

This paper describes the development and testing of a miniature one-pole, three-position pressure valve and actuation mechanism. This valve was designed primarily for installation with a pressure transducer directly in a wind-tunnel model, thereby reducing lag time effects resulting from long connecting tubes to the transducer. This valve provides for the in-situ calibration of the transducer during testing by providing one position for transducer zero, a second position for a known calibrate pressure, and a third position for measurement of the unknown test pressure. The valve is driven from the spring loaded test pressure position to the zero and calibrate positions by a pneumatically operated dual-piston yoke assembly. Large numbers of transducers can be simultaneously calibrated from a remote location in a matter of seconds.

Rollins, G. N.↗