Search NASA⌕ Search

SEARCH · Search NASA

Results for “RECTANGULAR PLANFORM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

A Wind Tunnel Investigation of a Small Scale Tiltrotor Model in Descending Flight

A small-scale tiltrotor model was tested in the 7-by 10-foot Wind Tunnel at NASA Ames Research Center, with the goal of better understanding Vortex Ring State (VRS) effects on tiltrotor aircraft. Test objectives were to obtain performance data of a tiltrotor model over a wide range of descent conditions, to explore the effects of sideslip at these descent conditions, and to investigate the validity of using a single-rotor with a physical image plane to simulate dual rotor performance characteristics. The model consisted of a pair of 2-bladed teetering rotors with untwisted, 11.125-inch diameter, rectangular planform blades. Model configuration variations included a dual-rotor, an isolated-rotor, and a single-rotor with a physical image plane. Rotor performance data were obtained for the dual-rotor configuration operating over a wide range of descent and sideslip conditions. Isolated-rotor and single-rotor with image plane configurations were tested over an abbreviated range of descent conditions. Results of this investigation are presented and show mean thrust reductions in the region of VRS for each model configuration. In comparison with the dual-rotor configuration, the isolated-rotor and single-rotor with image plane configurations produced thrust results similar in trend but different in magnitude.

Abrego, Anita I.↗
NASA NTRS2004

Detached-Eddy Simulations of Separated Flow Around Wings With Ice Accretions: Year One Report

A computational investigation was performed to assess the effectiveness of Detached-Eddy Simulation (DES) as a tool for predicting icing effects. The AVUS code, a public domain flow solver, was employed to compute solutions for an iced wing configuration using DES and steady Reynolds Averaged Navier-Stokes (RANS) equation methodologies. The configuration was an extruded GLC305/944-ice shape section with a rectangular planform. The model was mounted between two walls so no tip effects were considered. The numerical results were validated by comparison with experimental data for the same configuration. The time-averaged DES computations showed some improvement in lift and drag results near stall when compared to steady RANS results. However, comparisons of the flow field details did not show the level of agreement suggested by the integrated quantities. Based on our results, we believe that DES may prove useful in a limited sense to provide analysis of iced wing configurations when there is significant flow separation, e.g., near stall, where steady RANS computations are demonstrably ineffective. However, more validation is needed to determine what role DES can play as part of an overall icing effects prediction strategy. We conclude the report with an assessment of existing computational tools for application to the iced wing problem and a discussion of issues that merit further study.

Choo, Yung K.↗
NASA NTRS2005

RANS and DES Computations for a Wing with Ice Accretion

A computational investigation was performed to assess the effectiveness of Detached Eddy Simulation (DES) as a tool for predicting icing effects. The AVUS code, a public domain flow solver, was employed to compute solutions for an iced wing configuration using DES and steady Reynolds Averaged Navier-Stokes (RANS) equation methodologies. The wing section considered here was a business jet airfoil (GLC305) with a 22.5-minute glaze ice accretion (944-ice shape). The section was extruded to form a rectangular planform. The model was mounted between two walls so no tip effects were considered. The numerical results were validated by comparison with experimental data for the same configuration. The time-averaged DES computations showed some improvement in lift and drag results near stall when compared to steady RANS results. However, comparisons of the flow field details did not show the level of agreement suggested by the integrated quantities. More validation is needed to determine what role DES can play as part of an overall icing effects prediction strategy.

Mogili, P.↗
NASA NTRS2005

The Effect of Tip Geometry on Active-Twist Rotor Response

A parametric examination of the effect of tip geometry on active-twist rotor system response is conducted. Tip geometry parameters considered include sweep, taper, anhedral, nonlinear twist, and the associated radial initiation location for each of these variables. A detailed study of the individual effect of each parameter on active-twist response is presented, and an assessment offered of the effect of combining multiple tip shape parameters. Tip sweep is shown to have the greatest affect on active-twist response, significantly decreasing the response available. Tip taper and anhedral are shown to increase moderately the active-twist response, while nonlinear twist is shown to have a minimal effect. A candidate tip shape that provides active-twist response equivalent to or greater than a rectangular planform blade is presented.

Wilbur, Matthew L.↗
NASA NTRS2005

Loads and Performance Data from a Wind-Tunnel Test of Generic Model Helicopter Rotor Blades

An investigation was conducted in the NASA Langley Transonic Dynamics Tunnel to acquire data for use in assessing the ability of current and future comprehensive analyses to predict helicopter rotating-system and fixed-system vibratory loads. The investigation was conducted with a generic model helicopter rotor system using blades with rectangular planform, no built-in twist, uniform radial distribution of mass and stiffnesses, and a NACA 0012 airfoil section. Rotor performance data, as well as mean and vibratory components of blade bending and torsion moments, fixed-system forces and moments, and pitch link loads were obtained at advance ratios up to 0.35 for various combinations of rotor shaft angle-of-attack and collective pitch. The data are presented without analysis.

Yeager, William T., Jr.↗
DOE OSTI2024

The nonlinear behavior of generic tail fins for small wind turbines

This paper describes analysis and measurements of the yaw response of tail fins for small wind turbines. It is based on an extension of unsteady slender body theory (USBT) to cover non-slender fins and high angles of incidence, both of which make the theory nonlinear. We provide three main additions to the substantial literature on linearized USBT for tail fins. First, USBT is extended to high angles by modeling the nonlinear vortex dynamics. Second, the restriction to slender bodies is removed by modeling the chordwise load variation. Third, we consider the effect of time-varying wind speed. Further, the extended theory is compared to wind tunnel measurements of the yaw behavior of delta, elliptical, and rectangular tail fins without a rotor and nacelle. The fins were released from initial yaw angles of -40° and -80°; the latter is of sufficient magnitude to show the importance of the nonlinear yaw dynamics. Generally good agreement was found between the theory and measurements, and the theory was shown to be more accurate than a “polar” or quasi-steady model which uses only the lift and drag of a delta planform. Of the three planforms, the rectangular one showed the lowest accuracy in terms of frequency but the damping was accurately predicted. Overall, the results demonstrate the importance of nonlinearity in the response of a yawing tail fin, particularly for the higher aspect ratio fins at large yaw angles.

17 WIND ENERGY↗
NASA NTRS1991

Technical activities of the configuration aeroelasticity branch

A number of recent technical activities of the Configuration Aeroelasticity Branch of the NASA Langley Research Center are discussed in detail. The information on the research branch is compiled in twelve separate papers. The first of these topics is a summary of the purpose of the branch, including a full description of the branch and its associated projects and program efforts. The next ten papers cover specific projects and are as follows: Experimental transonic flutter characteristics of supersonic cruise configurations; Aeroelastic effects of spoiler surfaces mounted on a low aspect ratio rectangular wing; Planform curvature effects on flutter of 56 degree swept wing determined in Transonic Dynamics Tunnel (TDT); An introduction to rotorcraft testing in TDT; Rotorcraft vibration reduction research at the TDT; A preliminary study to determine the effects of tip geometry on the flutter of aft swept wings; Aeroelastic models program; NACA 0012 pressure model and test plan; Investigation of the use of extension twist coupling in composite rotor blades; and Improved finite element methods for rotorcraft structures. The final paper describes the primary facility operation by the branch, the Langley TDT.

Cole, Stanley R.↗
NASA NTRS1992

Finite wing aerodynamics with simulated glaze ice

The effect of a simulated glaze ice accretion on the aerodynamic performance of a three-dimensional wing is studied experimentally. The model used for these tests was a semi-span wing of effective aspect ratio five, mounted from the sidewall of the UIUC subsonic wind tunnel. The model has an NACA 0012 airfoil section on a rectangular, untwisted planform with interchangeable leading edges to allow for testing both the baseline and the iced wing geometry. A three-component sidewall balance was used to measure lift, drag and pitching moment on the clean and iced model. A four-beam two-color fiberoptic laser Doppler velocimeter (LDV) was used to map the flowfield along several spanwise cuts on the model. Preliminary results from LDV scans, which will be the bulk of this paper, are presented following the force balance measurement results. Initial comparison of LDV surveys compare favorably with inviscid theory results and 2D split hot-film measurements near the model surface.

Khodadoust, A.↗
NASA NTRS1992

Effect of a simulated glaze ice shape on the aerodynamic performance of a rectangular wing

The effect of a simulated glaze-ice accretion on the flowfield of a 3D wing is studied experimentally. The model used for these tests was a semispan wing of effective aspect ratio five, mounted from the sidewall of a subsonic wind tunnel. The model has a NACA 0012 airfoil section on a rectangular untwisted planform with interchangeable leading edges to allow for testing both the baseline and the iced-wing geometry. A four-beam two-color fiberoptic laser Doppler velocimeter (LDV) was used to map the flowfield along three spanwise cuts on the model. Measurements on the centerline of the clean model compared favorably with theory and centerline measurements on the iced model compared well with measurements on a similar 2D model. The flow has the largest separation bubble at the model midspan with the smallest separation bubble occurring near the root and the wing tip.

Khodadoust, Abdi↗
NASA NTRS1993

LDV flowfield measurements on a straight and swept wing with a simulated ice accretion

Simulated glaze ice accretion effects on a flowfield are presently studied for the case of a 3D semispan wing with NACA 0012 airfoil section on a rectangular untwisted planform. The model was tested at both zero-sweep and 30-deg sweep setting with four-beam/two-color LDV flowfield mapping. The comparison of LDV-measure velocity profiles with 3D Navier-Stokes predictions revealed correct trends, but with several differences that are attributable to the turbulence models and grid resolution used in the computations.

Bragg, M. B.↗
NASA NTRS1973

Wind tunnel simulation of full scale vortices

An experimental investigation has been conducted to determine the important scaling parameters for the flow in the core region of a vortex generated by a rectangular wing tip. The effect of an unconventional planform, the ogee tip, on the tip vortex is also determined. For rectangular planform wings, the measured vortex core diameter to chord ratios, peak tangential velocity ratios, and axial velocity ratios are shown to be functions only of wing lift coefficient and elapsed time from vortex formation, and appear to be independent of both Mach number and Reynolds number. The peak tangential velocities in the diffuse vortex generated by the ogee tip are only 25 percent of those in the vortex generated by the rectangular wing.

Rorke, J. B.↗
NASA NTRS1987

An experimental study of the aerodynamic characteristics of planar and non-planar outboard wing planforms

A series of wind tunnel experiments have been conducted to investigate the aerodynamic characteristics of several planar and nonplanar wingtip planforms. Seven different configurations: base-line rectangular, elliptical, swept and tapered, swept and tapered with dihedral, swept and tapered with anhedral, rising arc, and drooping arc, were investigated for two different spans. The data are available in terms of coefficient plots of force data, flow visualization photographs, and velocity and pressure flowfield surveys. All planforms, particularly the nonplanar, have some advantages over the baseline rectangular planform. Span efficiencies up to 20-percent greater than baseline are a possibility. However, it is suggested that the span efficiency concept might need refinement for nonplanar wings. Flow survey data show the change in effective span with vortex roll-up. The flow visualization shows the occurrence of mushroom-cell-separation flow patterns at angles of attack corresponding to stall. These grow with an increase in post-stall angle of attack. For the larger aspect ratios, the cells are observed to split into sub-cells at the higher angles of attack. For all angles of attack, some amount of secondary vortex flow is observed for the planar and nonplanar out-board planforms with sweep and taper.

Naik, D. A.↗
NASA NTRS1986

Effects of some geometric variations on missile aerodynamic characteristics at supersonic speeds

A summary of some results from tests of a wing-body general research missile model is presented for a Mach number range up to 4.63. A basic ogive-cylinder body with a length-to-diameter ratio of 10 was used to which was attached a series of wing planforms. The planforms included a family of delta wings and a family of rectangular wings having a constant root chord but varying spans so that wings of constant exposed area could be compared. In addition, a cranked-tip planform was included and a rectangular planform with reduced chord. Some results are presented for wing-body-tail configurations - one utilizing a cranked wing planform and one with wings having a constant root chord and span, but tip chords that were 0, 20, and 40 percent of the root chord.

Spearman, M. L.↗
NASA NTRS1986

Effects of some geometric variations on missile aerodynamic characteristics at supersonic speeds

A summary of some results from tests of a wing-body general research missile model is presented for a Mach number range up to 4.63. A basic ogive-cylinder body with a length-to-diameter ratio of 10 was used to which was attached a series of wing planforms. The planforms included a family of delta wings and a family of rectangular wings having a constant root chord but varying spans so that wings of constant exposed area could be compared. In addition, a cranked-tip planform was included and a rectangular planform with reduced chord. Some results are presented for wing-body-tail configurations - one utilizing a cranked wing planform and one with wings having a constant root chord and span, but tip chords that were 0, 20, and 40 percent of the root chord.

Spearman, M. L.↗
NASA NTRS1972

Wind tunnel simulation of full scale vortices.

An experimental investigation has been conducted to determine the important scaling parameters for the flow in the core region of a vortex generated by a rectangular wing tip. The effect of an unconventional planform, the ogee tip, on the tip vortex is also determined. Data were measured for wing pitch angles of 6 and 9 deg at Mach numbers of 0.2, 0.5, and 0.6 for Reynolds numbers ranging from 440,000 to 7,000,000 using a triaxial hot wire probe. The probe was located at 2 and 5 chordlengths downstream from the trailing edge of the 4.25 inch and 26.0 inch chord wings. For rectangular planform wings, the measured vortex core diameter to chord ratios, peak tangential velocity ratios, and axial velocity ratios are shown to be functions only of wing lift coefficient and elapsed time from vortex formation, and appear to be independent of both Mach number and Reynolds number.

Rorke, J. B.↗
NASA NTRS1992

Effect of blade planform variation on the forward-flight performance of small-scale rotors

An investigation was conducted in the Glenn L. Martin Wind Tunnel to determine the effect of blade planform variation on the forward-flight performance of four small-scale rotors. The rotors were 5.417 ft in diameter and differed only in blade planform geometry. The four planforms were: (1) rectangular; (2) 3:1 linear taper starting at 94 percent radius; (3) 3:1 linear taper starting at 75 percent radius; and (4) 3:1 linear taper starting at 50 percent radius. Each planform had a thrust-weighted solidity of 0.098. The investigation included forward-flight simulation at advance ratios from 0.14 to 0.43 for a range of rotor lift and drag coefficients. Among the four rotors, the rectangular rotor required the highest torque for the entire range of rotor drag coefficients attained at advanced ratios greater than 0.14 for rotor lift coefficients C sub L from 0.004 to 0.007. Among the rotors with tapered blades and for C sub L = 0.004 to 0.007, either the 75 percent tapered rotor or the 50 percent tapered rotor required the least amount of torque for the full range of rotor drag coefficients attained at each advance ratio. The performance of the 94 percent tapered rotor was generally between that of the rectangular rotor and the 75 and 50 percent tapered rotors at each advance ratio for this range of rotor lift coefficients.

Noonan, Kevin W.↗
NASA NTRS1991

Flapping inertia for selected rotor blades

Aerodynamics of helicopter rotor systems cannot be investigated without consideration for the dynamics of the rotor. One of the principal properties of the rotor which affects the rotor dynamics is the inertia of the rotor blade about its root attachment. Previous aerodynamic investigation have been performed on rotor blades with a variety of planforms to determine the performance differences due to blade planform. The blades tested for this investigation have been tested on the U.S. Army 2 meter rotor test system (2MRTS) in the NASA Langley 14 by 22 foot subsonic tunnel for hover performance. This investigation was intended to provide fundamental information on the flapping inertia of five rotor blades with differing planforms. The inertia of the bare cuff and the cuff with a blade extension were also measured for comparison with the inertia of the blades. Inertia was determined using a swing testing technique, using the period of oscillation to determine the effective flapping inertia. The effect of damping in the swing test was measured and described. A comparison of the flapping inertials for rectangular and tapered planform blades of approximately the same mass showed the tapered blades to have a lower inertia, as expected.

Berry, John D.↗