Search NASA⌕ Search

SEARCH · Search NASA

Results for “REENTRY VEHICLE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Two-layer convective heating prediction procedures and sensitivities for blunt body reentry vehicles

This paper provides a description of procedures typically used to predict convective heating rates to hypersonic reentry vehicles using the two-layer method. These procedures were used to compute the pitch-plane heating distributions to the Apollo geometry for a wind tunnel test case and for three flight cases. Both simple engineering methods and coupled inviscid/boundary layer solutions were used to predict the heating rates. The sensitivity of the heating results in the choice of metrics, pressure distributions, boundary layer edge conditions, and wall catalycity used in the heating analysis were evaluated. Streamline metrics, pressure distributions, and boundary layer edge properties were defined from perfect gas (wind tunnel case) and chemical equilibrium and nonequilibrium (flight cases) inviscid flow-field solutions. The results of this study indicated that the use of CFD-derived metrics and pressures provided better predictions of heating when compared to wind tunnel test data. The study also showed that modeling entropy layer swallowing and ionization had little effect on the heating predictions.

Bouslog, Stanley A.↗
NASA NTRS1972

Water landing characteristics of a model of a winged reentry vehicle

Proposed manned space shuttle vehicles are expected to land on airport runways. In an emergency situation, however, the vehicle may be required to land on water. A 1/10-scale dynamic model of a winged reentry vehicle was investigated to determine the water landing characteristics. Two configurations of the proposed vehicle were studied. Configuration 1 had a 30 deg negative dihedral of the stabilizer-elevon surface whereas configuration 2 had a 30 deg positive dihedral. Results indicate that the maximum normal accelerations for configurations 1 and 2 when landing in calm water were approximately 8g and 6g, respectively, and the maximum longitudinal accelerations were approximately 5g and 3g, respectively. A small hydroflap was needed to obtain satisfactory calm-water landings with configuration 2, whereas configuration 1 gave good landings without a hydroflap. All landings made in rough water resulted in unsatisfactory motions. For landings made in three different wave sizes, both configurations dived. The maximum normal accelerations for configurations 1 and 2 when landing in waves were -10.1g and -18.7g, respectively, and the maximum longitudinal accelerations for both configurations were approximately 13g.

Stubbs, S. M.↗
NASA NTRS2002

Aerodynamic Assessment of Flight-Determined Subsonic Lift and Drag Characteristics of Seven Lifting-Body and Wing-Body Reentry Vehicle Configurations

This report examines subsonic flight-measured lift and drag characteristics of seven lifting-body and wing-body reentry vehicle configurations with truncated bases. The seven vehicles are the full-scale M2-F1, M2-F2, HL-10, X-24A, X-24B, and X-15 vehicles and the Space Shuttle Enterprise. Subsonic flight lift and drag data of the various vehicles are assembled under aerodynamic performance parameters and presented in several analytical and graphical formats. These formats are intended to unify the data and allow a greater understanding than individually studying the vehicles allows. Lift-curve slope data are studied with respect to aspect ratio and related to generic wind-tunnel model data and to theory for low-aspect-ratio platforms. The definition of reference area is critical for understanding and comparing the lift data. The drag components studied include minimum drag coefficient, lift-related drag, maximum lift-to drag ratio, and, where available, base pressure coefficients. The influence of forebody drag on afterbody and base drag at low lift is shown to be related to Hoerner's compilation for body, airfoil, nacelle, and canopy drag. This feature may result in a reduced need of surface smoothness for vehicles with a large ratio of base area to wetted area. These analyses are intended to provide a useful analytical framework with which to compare and evaluate new vehicle configurations of the same generic family.

Saltzman, Edwin J.↗
NASA NTRS1960

Landing Energy Dissipation for Manned Reentry Vehicles

Analytical and experimental investigations have been made to determine the landing-energy-dissipation characteristics for several types of landing gear for manned reentry vehicles. The landing vehicles are considered in two categories: those having essentially vertical-descent paths, the parachute-supported vehicles, and those having essentially horizontal paths, the lifting vehicles. The energy-dissipation devices discussed are crushable materials such as foamed plastics and honeycomb for internal application in couch-support systems, yielding metal elements as part of the structure of capsules or as alternates for oleos in landing-gear struts, inflatable bags, braking rockets, and shaped surfaces for water impact. It appears feasible to readily evaluate landing-gear systems for internal or external application in hard-surface or water landings by using computational procedures and free-body landing techniques with dynamic models. The systems investigated have shown very interesting energy-dissipation characteristics over a considerable range of landing parameters. Acceptable gear can be developed along lines similar to those presented if stroke requirements and human-tolerance limits are considered.

Fisher, Lloyd J., Jr.↗
NASA NTRS1999

Flight-Determined Subsonic Lift and Drag Characteristics of Seven Lifting-Body and Wing-Body Reentry Vehicle Configurations With Truncated Bases

This paper examines flight-measured subsonic lift and drag characteristics of seven lifting-body and wing-body reentry vehicle configurations with truncated bases. The seven vehicles are the full-scale M2-F1, M2-F2, HL-10, X-24A, X-24B, and X-15 vehicles and the Space Shuttle prototype. Lift and drag data of the various vehicles are assembled under aerodynamic performance parameters and presented in several analytical and graphical formats. These formats unify the data and allow a greater understanding than studying the vehicles individually allows. Lift-curve slope data are studied with respect to aspect ratio and related to generic wind-tunnel model data and to theory for low-aspect-ratio planforms. The proper definition of reference area was critical for understanding and comparing the lift data. The drag components studied include minimum drag coefficient, lift-related drag, maximum lift-to-drag ratio, and, where available, base pressure coefficients. The effects of fineness ratio on forebody drag were also considered. The influence of forebody drag on afterbody (base) drag at low lift is shown to be related to Hoerner's compilation for body, airfoil, nacelle, and canopy drag. These analyses are intended to provide a useful analytical framework with which to compare and evaluate new vehicle configurations of the same generic family.

Saltzman, Edwin J.↗
NASA NTRS1962

Effects of Booster Transition Section and Rudder Deflection on the Low-Angle-of-Attack Static Stability of a Winged Reentry Vehicle at Mach Numbers of 10.8 and 17.8 in Helium

An investigation has been carried out to obtain aerodynamic stability and control data on a model of a winged reentry vehicle at Mach numbers of 10.8 and 17.8 in helium. The effects of a booster transition section on the static stability were obtained at angles of attack from -5 deg to 15 deg and at angles of sideslip from -5 deg to 10 deg at an angle of attack of 0 deg. Directional control data were also obtained at an angle of attack of 0 deg for sideslip angles from -5 deg to 10 deg. No detailed analysis of the data has been made.

Ladson, Charles L.↗
NASA NTRS2008

Using Pressure- and Temperature-Sensitive Paint for Global Surface Pressure and Temperature Measurements on the Aft-Body of a Capsule Reentry Vehicle

Pressure Sensitive Paint (PSP) and Temperature Sensitive Paint (TSP) were used to visualize and quantify the surface interactions of reaction control system (RCS) jets on the aft body of capsule reentry vehicle shapes. The first model tested was an Apollo-like configuration and was used to focus primarily on the effects of the forward facing roll and yaw jets. The second model tested was an early Orion Crew Module configuration blowing only out of its forward-most yaw jet, which was expected to have the most intense aerodynamic heating augmentation on the model surface. This paper will present the results from the experiments, which show that with proper system design, both PSP and TSP are effective tools for studying these types of interaction in hypersonic testing environments.

Watkins, A. Neal↗
NASA NTRS1993

Design of a recovery system for a reentry vehicle

Engineers are often required to design decelerator systems which are deployed in cross-wind orientations. If the system is not designed to minimize 'line sail', damage to the parachutes could result. A Reentry Vehicle Analysis Code (RVAC) and an accompanying graphics animation software program (DISPLAY) are presented in this paper. These computer codes allow the user to quickly apply the Purvis line sail modeling technique to any vehicle and then observe the relative motion of the vehicle, nose cap, suspension lines, pilot and drogue bags and canopies on a computer screen. Data files are created which allow plots of velocities, spacial positions, and dynamic pressures versus time to be generated. The code is an important tool for the design engineer because it integrates two degrees of freedom (DOF) line sail equations with a three DOF model of the reentry body and jettisoned nose cap to provide an animated output.

Von Eckroth, Wulf↗
NASA NTRS1980

Thermal protection of reentry vehicles by actively cooled nosetips

Analytical modeling efforts and clear-air ground test results of a transportation-cooled nosetips (TCNT) design are presented. The discrete water injection platelet TCNT described was conceived and created to achieve the performance requirements for severe reentry vehicle trajectories. Thermal performance computer modeling techniques, combing both local heat blockage and boundary layer recovery enthalpy reduction are outlined.

Walker, R. E.↗
NASA NTRS1958

Structural design considerations for boost-glide and orbital reentry vehicles

The preceding papers have discussed the aerodynamics and heating of several vehicles designed for atmospheric reentry from satellite orbits. Because of large heating inputs, some fundamental questions about the structure of these vehicles are also raised. Although there are many factors which influence structural design, only a brief examination of the relationship between heating input and structural weight is discussed here. For this purpose the heating inputs associated with the four vehicles shown in figure 1 are employed.

William A. Brooks, Jr.↗