Search NASA⌕ Search

SEARCH · Search NASA

Results for “ROLL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Rolling-Element Bearings

Rolling element bearings are a precision, yet simple, machine element of great utility. A brief history of rolling element bearings is reviewed and the type of rolling element bearings, their geometry and kinematics, as well as the materials they are made from and the manufacturing processes they involve are described. Unloaded and unlubricated rolling element bearings, loaded but unlubricated rolling element bearings and loaded and lubricated rolling element bearings are considered. The recognition and understanding of elastohydrodynamic lubrication covered, represents one of the major development in rolling element bearings.

Hamrock, B. J.↗
NASA NTRS1986

Investigation of limb-sidestick dynamic interaction with roll control

A fixed-base simulation was performed to identify and quantify interactions between the pilot's hand/arm neuromuscular subsystem and such features of typical modern fighter aircraft roll rate command control system mechanization as: (1) force sensing side-stick type manipulator; (2) vehicle effective roll time constant; and (3) flight control system effective time delay. The simulation results provide insight to high frequency pilot induced oscillations (PIO) (roll ratchet), low frequency PIO, and roll-to-right control and handling problems previously observed in experimental and production fly-by-wire control systems. The simulation configurations encompass and/or duplicate several actual flight situations, reproduce control problems observed in flight, and validate the concept that the high frequency nuisance mode known as roll ratchet derives primarily from the pilot's neuromuscular subsystem. The simulations show that force-sensing side-stick manipulator force/displacement/command gradients, command prefilters, and flight control system time delays need to be carefully adjusted to minimize neuromuscular mode amplitude peaking (roll ratchet tendency) without restricting roll control bandwidth (with resulting sluggish or PIO prone control).

Johnston, D. E.↗
NASA NTRS1960

Experimental Determination of the Effects of Frequency and Amplitude of Oscillation on the Roll-Stability Derivatives for a 60 Degree Delta-Wing Airplane Model

A 60' delta-wing airplane model was oscillated in roll for several frequencies and amplitudes of oscillation to determine the effects of the oscillatory motion on the roll-stability derivatives for the model. The derivatives were measured at a Reynolds number of 1,600,000 for the wing alone, the wing-fuselage combination, and the complete model which included a triangular-plan-form vertical tail. Both rolling and yawing moments due to rolling velocity exhibited large frequency effects for angles of attack higher than 16 degrees. Variations in these derivatives were measured for the lowest frequencies of oscillation; as the frequency increased, the derivatives because more nearly linear with angle of attack. Both velocity derivatives were considerably different at high angles of attack from the corresponding derivatives measured by the steady-state rolling-flow technique. Rolling and yawing moments due to rolling acceleration were measured and similarly found to be highly dependent on frequency at high angles of attack. Some period and time-to-damp computations, which were made to reveal the significance of the acceleration derivatives, indicated that inclusion of the measured derivatives in the equations of motion lengthened the period of the lateral oscillation by 10 percent for a typical delta-wing airplane and increased the time to damp to one-half amplitude by 50 percent.

Fisher, Lewis R.↗
NASA NTRS1991

Conical Euler methodology for unsteady vortical flows about rolling delta wings

A conical Euler methodology was developed to study unsteady vortex-dominated flows about rolling highly swept delta wings undergoing either forced or free-to-roll motions. The flow solver of the code involves a multistage Runge-Kutta time-stepping scheme which uses a finite-volume spatial discretization of the Euler equations on an unstructured grid of triangles. Results are presented for a 75-deg swept sharp-leading-edge delta wing at a freestream Mach number of 1.2 and at alpha = 10, 20, and 30 deg. At the 10 and 20 deg, forced harmonic analyses indicate that the rolling moment coefficients provide a positive damping which is verified by free-to-roll calculations. In contrast, at 30 deg, a forced harmonic analysis indicates that the rolling moment coefficient provides a negative damping at the small roll amplitudes. A free-to-roll calculation for this case produces an initially divergent response, but as the amplitude of motion grows with time, the response transitions to a wing-rock type of limit cycle oscillation.

Lee, Elizabeth M.↗
NASA NTRS1949

Investigation at low speeds of the effect of aspect ratio and sweep on rolling stability derivatives of untapered wings

A low scale wind tunnel investigation was conducted in rolling flow to determine the effects of aspect ratio and sweep (when varied independently) on the rolling stability derivatives for a series of untapered wings. Test results indicate that when the aspect ratio was held constant, an increase in the sweepback angle caused a significant reduction in the damping in roll at low lift coefficients for only the higher aspect ratios that were tested. This result was in agreement with available swept wing theory which indicated no effect of sweep for aspect ratios near zero. The result of the linear theory that the damping in roll is independent of lift coefficient and that the yawing moment and lateral force due to rolling are directly proportional to the lift coefficient was found to be valid for only a very limited lift coefficient range when the wings were highly swept. For such wings, the damping was found to increase in magnitude and the yawing moment due to rolling, to change from negative to positive at moderate lift coefficients. The effect of wing tip suction, not acounted for by present theory, was found to be very important with regard to the yawing moment due to rolling, particularly for low aspect ratio swept wings. An empirical means of correcting present theory for the effect of tip suction is suggested.

Goodman, Alex↗
NASA NTRS1993

A study of roll attractor and wing rock of delta wings at high angles of attack

Wing rock is a high angle of attack dynamic phenomenon of limited cycle motion predominantly in roll. The wing rock is one of the limitations to combat effectiveness of the fighter aircraft. Roll Attractor is the steady state or equilibrium trim angle (phi(sub trim)) attained by the free-to-roll model, held at some angle of attack, and released form rest at a given initial roll (bank) angle (phi(sub O)). Multiple roll attractors are attained at different trim angles depending on initial roll angle. The test facility (Vigyan's low speed wind tunnel) and experimental work is presented here along with mathematical modelling of roll attractor phenomenon and analysis and comparison of predictions with experimental data.

Niranjana, T.↗
NASA NTRS1993

Judging rolling wheels: Dynamic and kinematic aspects of rotation-translation coupling

Four experiments were carried out to investigate observers' abilities to judge rolling motions. The experiments were designed to assess whether two important aspects of such motions are appreciated: the kinematic coupling of rotation and translation, and the dynamic effects of gravity. Different motion contexts of rolling wheels were created using computer-generated displays. The first experiment involved wheels rolling down an inclined plane. Observers spontaneously appreciated the anomaly of wheels that failed to accelerate, but they were not able to differentiate between different acceleration functions. Moreover, their judgements were almost exclusively based on the translation component of the rolling motion, neglecting the rotation component. In a second experiment it was found that observers could accurately estimate the perimeter of various objects. Thus, their inability to consider rotation information is not attributable to misperceptions of the geometry of wheels. In a third experiment the finding that rolling wheels appear to overrotate was replicated; however, findings from this experiment also showed, together with those from a fourth experiment, that observers are able to make very accurate judgments about translation-rotation coupling in rolling wheels when information is provided about the orientation of the wheel and the texture of the surface on which it rolls.

Hecht, Heiko↗
NASA NTRS2007

Free-to-Roll Testing of Airplane Models in Wind Tunnels

A free-to-roll (FTR) test technique and test rig make it possible to evaluate both the transonic performance and the wingdrop/ rock behavior of a high-strength airplane model in a single wind-tunnel entry. The free-to-roll test technique is a single degree-of-motion method in which the model is free to roll about the longitudinal axis. The rolling motion is observed, recorded, and analyzed to gain insight into wing-drop/rock behavior. Wing-drop/rock is one of several phenomena symptomatic of abrupt wing stall. FTR testing was developed as part of the NASA/Navy Abrupt Wing Stall Program, which was established for the purposes of understanding and preventing significant unexpected and uncommanded (thus, highly undesirable) lateral-directional motions associated with wing-drop/rock, which have been observed mostly in fighter airplanes under high-subsonic and transonic maneuvering conditions. Before FTR testing became available, wingrock/ drop behavior of high-performance airplanes undergoing development was not recognized until flight testing. FTR testing is a reliable means of detecting, and evaluating design modifications for reducing or preventing, very complex abrupt wing stall phenomena in a ground facility prior to flight testing. The FTR test rig was designed to replace an older sting attachment butt, such that a model with its force balance and support sting could freely rotate about the longitudinal axis. The rig (see figure) includes a rotary head supported in a stationary head with a forward spherical roller bearing and an aft needle bearing. Rotation is amplified by a set of gears and measured by a shaft-angle resolver; the roll angle can be resolved to within 0.067 degrees at a rotational speed up to 1,000 degrees/s. An assembly of electrically actuated brakes between the rotary and stationary heads can be used to hold the model against a rolling torque at a commanded roll angle. When static testing is required, a locking bar is used to fix the rotating head rigidly to the stationary head. Switching between the static and FTR test modes takes only about 30 minutes. The FTR test rig was originally mounted in a 16-ft (approximately 4.0-m) transonic wind tunnel, but could just as well be adapted to use in any large wind tunnel. In one series of tests on the FTR rig, static and dynamic characteristics of models of four different fighter airplanes were measured. Two of the models exhibited uncommanded lateral motions; the other two did not. A figure of merit was developed to discern the severity of lateral motions. Using this figure of merit, it was shown that the FTR test technique enabled identification of conditions under which the uncommanded lateral motions occurred. The wind-tunnel conditions thus identified were found to be correlated with flight conditions under which the corresponding full-size airplanes exhibited uncommanded lateral motions.

Capone, Francis J.↗
DOE OSTI2024

Effects of Rolling Reduction on Critical Current Density and Microstructure of Bi-2212 Wires

Bi-2212 Rutherford cables have been fabricated into flat racetrack coils and canted-cosine-theta dipole magnets. The performance gap between the magnets made with Rutherford cables and the “short-sample-limit” is about 30%. To better understand the influence of Rutherford cable processing on the strand performance, we studied three Bi-2212 wires with filament architectures of 37 × 18 and 55 × 18 and diameters of 0.8 and 1.0 mm. To simulate the deformation caused by cabling process, the three wires were rolled with thickness reductions ranging from 10% to 30%. The aspect ratios of rolled strands are between 1.29 and 2.05. The low aspect-ratio wire is also an interesting form for fabricating solenoid coils with higher packing density. The round and rolled strands were heat-treated under 50 bar and with maximum heat treatment temperatures of 885.5 °C and 890.5 °C. The rolling deformation reduced filament size uniformity, resulting in filament merging in fully heat-treated wires. It was found that rolling reduction reduced wire critical current density (JE) by 16 to 18%, but the JE decrease saturated at 15 to 20% of the thickness reduction. It is believed that the reduced JE results from the filament merging caused by rolling and non-uniform shrinking during overpressure heat treatment.

Bi-2212 wire↗
NASA NTRS1974

Aerodynamic roll damping of a T-tail transport configuration

The aerodynamic roll damping and the yawing moment due to roll rate for a model of a T-tail transport with aft-mounted engines were measured by means of a small-amplitude forced-oscillation mechanism. The tests were made for Mach numbers between 0.21 and 0.80 over a range of angles of attack from about minus 4 deg to 22 deg. The basic configuration had positive damping in roll at low angles of attack with regions of low positive and negative damping for angles of attack above 8 deg to 10 deg. There was good agreement between the theoretical estimates of the roll damping for the wing alone and the experimental results at an angle of attack of 0 deg for Mach numbers of 0.60 and less. The T-tail configuration and the engine nacelles mounted aft on the fuselage did not significantly affect either the damping in roll or the yawing moment due to roll rate.

Boyden, R. P.↗
NASA NTRS1973

Roll paper pilot

A mathematical model for predicting the pilot rating of an aircraft in a roll task is described. The model includes: (1) the lateral-directional aircraft equations of motion; (2) a stochastic gust model; (3) a pilot model with two free parameters; and (4) a pilot rating expression that is a function of rms roll angle and the pilot lead time constant. The pilot gain and lead time constant are selected to minimize the pilot rating expression. The pilot parameters are then adjusted to provide a 20% stability margin and the adjusted pilot parameters are used to compute a roll paper pilot rating of the aircraft/gust configuration. The roll paper pilot rating was computed for 25 aircraft/gust configurations. A range of actual ratings from 2 to 9 were encountered and the roll paper pilot ratings agree quite well with the actual ratings. In addition there is good correlation between predicted and measured rms roll angle.

Naylor, F. R.↗
NASA NTRS1984

Accuracy of System Step Response Roll Magnitude Estimation from Central and Peripheral Visual Displays and Simulator Cockpit Motion

An experiment to investigate visual roll attitude and roll rate perception is described. The experiment was also designed to assess the improvements of perception due to cockpit motion. After the onset of the motion, subjects were to make accurate and quick estimates of the final magnitude of the roll angle step response by pressing the appropriate button of a keyboard device. The differing time-histories of roll angle, roll rate and roll acceleration caused by a step response stimulate the different perception processes related the central visual field, peripheral visual field and vestibular organs in different, yet exactly known ways. Experiments with either of the visual displays or cockpit motion and some combinations of these were run to asses the roles of the different perception processes. Results show that the differences in response time are much more pronounced than the differences in perception accuracy.

Hosman, R. J. A. W.↗
NASA NTRS1987

Long term prediction of roll phase for an undisturbed spinning spacecraft

This paper describes the attitude control of the Pioneer 10 spacecraft since the loss of the sun-sensor signal in late 1983. It is necessary to control the attitude of the spin-stablized spacecraft so as to maintain communications with earth. Roll phase is calculated on earth using data from a science instrument on-board Pioneer 10, the imaging-photopolarimeter, which, along with its other functions, was designed to collect images of Jupiter during encounter in 1973. With calculation of instantaneous roll phase performed only once per week, the spacecraft roll angle can be predicted more than a week ahead for timing reorientation impulses. Attitude reorientation maneuvers based on roll phase predictions have been successfully executed for several years on Pioneer 10. Of 10 maneuvers analyzed in this paper, predictions were made for as many as 10 days in the future based on a roll-phase measurements spanning only 12 days of data. The average maneuver was planned by projecting the roll phase for 3 days (22,000 spacecraft revolutions) and resulted in a maneuver execution phase error of only 11 deg.

Smith, M. A.↗
NASA NTRS1986

Investigation of interactions between limb-manipulator dynamics and effective vehicle roll control characteristics

A fixed-base simulation was performed to identify and quantify interactions between the pilot's hand/arm neuromuscular subsystem and such features of typical modern fighter aircraft roll rate command control system mechanization as: (1) force sensing side-stick type manipulator; (2) vehicle effective role time constant; and (3) flight control system effective time delay. The simulation results provide insight to high frequency pilot induced oscillations (PIO) (roll ratchet), low frequency PIO, and roll-to-right control and handling problems previously observed in experimental and production fly-by-wire control systems. The simulation configurations encompass and/or duplicate actual flight situations, reproduce control problems observed in flight, and validate the concept that the high frequency nuisance mode known as roll ratchet derives primarily from the pilot's neuromuscular subsystem. The simulations show that force-sensing side-stick manipulator force/displacement/command gradients, command prefilters, and flight control system time delays need to be carefully adjusted to minimize neuromuscular mode amplitude peaking (roll ratchet tendency) without restricting roll control bandwidth (with resulting sluggish or PIO prone control).

Johnston, D. E.↗
NASA NTRS1987

The design of blended rolled edges for compact range main reflectors

In a compact range (which employs a parabolic main reflector to convert the spherical wave originating from a point source to a reflected plane wave) the edge-generated diffractive fields degrade the uniformity of the plane wave. To reduce the energy diffracted from the edge surfaces, terminations can be added to the parabola, such that the slope of the surface is continuous at the junctions. This paper discusses the problem of designing an optimized rolled edge. Two examples of reflectors with rolled edges are presented, one with elliptic rolled edges and the other with blended rolled edges, both adhering to the same constraints on minimum operating frequency and size. It was found that the reflector with the cosine-squared blended rolled edges has a much larger usable target zone than the one with the elliptic rolled edges.

Pistorius, C. W. I.↗
NASA NTRS1990

Self-induced roll oscillations of low-aspect-ratio rectangular wings

Experimental investigation of small aspect ratio rectangular wings mounted on a free-to-roll sting balance indicated that self-induced roll oscillations are possible when the aspect ratio of such wings is less than 0.5. The oscillations are probably driven by the periodic changes in the location and strength of the side edge vortices, as it has been shown for the 'wing rock' motion of delta wings, where similar changes in the leading edge vortex strength and position cause the roll oscillations. During the roll oscillation cycle the roll angle, normal force, and the side force were recorded and presented for three wings with aspect ratios of 0.25, 0.35, and 0.47. This data indicates that the lift loss during roll oscillations of rectangular wings is less than what was measured for similar delta wings. Also, the flow field of such slender rectangular wings at high angles of attack is more complicated due to the additional leading edge vortex, when compared with the flow field over slender delta wings.

Levin, Daniel↗
NASA NTRS1990

Supersonic aerodynamic characteristics of a maneuvering canard-controlled missile with fixed and free-rolling tail fins

Wind tunnel investigations were conducted on a generic cruciform canard-controlled missile configuration. The model featured fixed or free-rolling tail-fin afterbodies to provide an expanded aerodynamic data base with particular emphasis on alleviating large induced rolling moments and/or for providing canard roll control throughout the entire test angle-of-attack range. The tests were conducted in the NASA Langley Unitary Plan Wind Tunnel at Mach numbers from 2.50 to 3.50 at a constant Reynolds number per foot of 2.00 x 10 to the 6th. Selected test results are presented to show the effects of a fixed or free-rolling tail-fin afterbody on the static longitudinal and lateral-directional aerodynamic characteristics of a canard-controlled missile with pitch, yaw, and roll control at model roll angles of 0 deg and 45 deg.

Blair, A. B., Jr.↗
NASA NTRS1992

Navier-Stokes prediction of large-amplitude delta-wing roll oscillations characterizing wing rock

High-incidence vortical flow about a 65-deg sweep delta wing undergoing static roll and large-amplitude, high-rate-of-roll oscillations is simulated numerically using the time-dependent, three-dimensional, Reynolds-averaged, Navier-Stokes equations. Turbulent computations are presented for static roll angles up through 42 degrees. The effects of roll angle on the vortex aerodynamics are discussed, and the solution accuracy is evaluated by comparison with experimental data. The effects of grid refinement and zonal boundary condition treatment on solution accuracy are assessed at zero roll angle. Numerical simulation of a forced periodic roll motion is also presented.

Chaderjian, Neal M.↗