Search NASA⌕ Search

SEARCH · Search NASA

Results for “Reduced Diameter”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

A status review on DNB prediction using CASL baseline boiling model and possible suggestions regarding wall boiling closures

The main goal of FY18 THM’s focus task is to evaluate where the current CASL boiling model stands for DNB predictive performance, to identify which components should be improved or calibrated to enhance DNB performance. Over the past three year’s validation tests, Gen1A boiling model has presented an under-predictive behavior for DNB at the high pressure of interest for PWR application. With this in mind, this year’s task is to focus on 1) best practice guidelines on DNB detection criteria, 2) interfacial momentum transfer closure tests, and 3) wall boiling closure sensitivity on DNB. Best practice guidelines on DNB detection criteria are demonstrated by the following three monitoring variables: 1) max wall temperature, 2) K-value and 3) energy balance. Interfacial momentum transfer closure govern the bubble distribution, especially in lateral direction, as well as bubble mean diameter. A clear correlation between interfacial momentum closure and DNB prediction is not observed in the current tests. However, void distributions are changed with different interfacial momentum closure tests which requires further validation with corresponding experimental measurement. From a variety of wall boiling closure tests, bubble departure diameter seems the most sensitive for DNB performance while fulfilling numerical robustness in DNB simulation. Tolubinski’s bubble departure diameter model was calibrated to see if any improvement is observed in DNB performance. Notable DNB improvement was observed as the bubble departure diameter is reduced. However, reduced bubble departure diameter by calibrated Tolubinski’s model seemed to lead to relatively high wall superheat temperature prediction which requires further validation with associated experimental measurement It should be noted that lack of experimental measurement close to DNB condition hampers this boiling closure sensitivity study significantly. This situation directly reflects some of limitations of the CASL boiling model development. With this in mind, the implementation of improved boiling closure on 5x5 NMVG and MVG tests will be pursued in FY19, the associated DNB best practice guidelines and possible limitations will be addressed for industry DNB application.

42 ENGINEERING↗

Crater Population on Asteroid (101955) Bennu Indicates Impact Armouring and a Young Surface

The impactor-to-crater size scaling relationships that enable estimates of planetary surface ages rely on an accurate formulation of impactor–target physics. An armouring regime, specific to rubble-pile surfaces, has been proposed to occur when an impactor is comparable in diameter to a target surface particle (for example, a boulder). Armouring is proposed to reduce crater diameter, or prevent crater formation in the asteroid surface, at small crater diameters. Here, using measurements of 1,560 craters on the rubble-pile asteroid (101955) Bennu, we show that the boulder population controls a transition from crater formation to armouring at crater diameters ~2–3 m, below which crater formation in the bulk surface is increasingly rare. By combining estimates of impactor flux with the armouring scaling relationship, we find that Bennu’s crater retention age (surface age derived from crater abundance) spans from 1.6–2.2 Myr for craters less than a few meters to ~10–65 Myr for craters >100 m in diameter, reducing the maximum surface age by a factor of >15 relative to previous estimates. The range of crater retention ages, together with latitudinal variations in large-crater spatial density, indicate that ongoing resurfacing processes render the surface many times younger than the bulk asteroid.

Asteroids↗

Crater population on asteroid (101955) Bennu indicates impact armouring and a young surface

The impactor-to-crater size scaling relationships that enable estimates of planetary surface ages rely on an accurate formulation of impactor–target physics. An armouring regime, specific to rubble-pile surfaces, has been proposed to occur when an impactor is comparable in diameter to a target surface particle (for example, a boulder). Armouring is proposed to reduce crater diameter, or prevent crater formation in the asteroid surface, at small crater diameters. Here, using measurements of 1,560 craters on the rubble-pile asteroid (101955) Bennu, we show that the boulder population controls a transition from crater formation to armouring at crater diameters ~2–3m, below which crater formation in the bulk surface is increasingly rare. By combining estimates of impactor flux with the armouring scaling relationship, we find that Bennu’s crater retention age (surface age derived from crater abundance) spans from 1.6–2.2Myr for craters less than a few meters to ~10–65Myr for craters >100m in diameter, reducing the maximum surface age by a factor of >15 relative to previous estimates. The range of crater retention ages, together with latitudinal variations in large-crater spatial density, indicate that ongoing resurfacing processes render the surface many times younger than the bulk asteroid.

E. B. Bierhaus↗

Perform Life Cycle Energy and GHG Emission Analysis, Select Candidate Refrigerant(s), Developing Heat Pump by Using Low-GWP Refrigerants and 5 mm Diameter Tubes

Reducing environmental impacts from the energy conversion systems has been an important research topic due to recent severe global climate changes. In residential buildings, the space heating and cooling are main energy consumers, which are relying on vapor compression based heat pumps. To mitigate the environmental impacts of residential systems, the heat pumps using low-GWP refrigerants and 5mm-tube heat exchangers are proposed to replace the conventional 9 mm or 7 mm tube heat exchangers. This research uses a simulation-based design method to optimize the refrigerant circuitries of a 5-ton low-GWP refrigerant heat pumps whose indoor and outdoor heat exchangers adopt 5 mm tubes. Heat pump systems using four commercially available low-GWP refrigerants (R454A, R454C, ARM20A and ARM20B) are optimized and compared with the baseline R410A system. The results indicate that directly replacing 9 mm tubes into 5mm tubes in the baseline systems induces heat pump performance degradation; by optimizing the 5 mm tube heat pumps with added tube rows, the system refrigerant charge is reduced up to 33% compared with the baseline; the optimized low-GWP 5 mm tube heat pumps offer the same or higher performance under both cooling and heating mode; that under cooling mode, the EER improvement is up to 10.7% and under heating mode the COP improvement is up to 3.4%; and a smart flow control device to maintain counter-flow circuitry pattern on both operating modes can improve the heating performance of 5 mm tube optimized system by up to 3.0%. In an effort to better understand the environmental impacts of these systems, life cycle climate performance (LCCP) evaluation method is used to assess the baseline and optimized systems. LCCP considers the direct and indirect emissions of the system over the course of its lifetime from manufacturing to disposal. Our analyses indicate that the optimized systems using 5mm tubes and low-GWP refrigerants can reduce life-cycle CO 2 emission significantly. And improving system efficiency is the most effective way to reduce the emission of low-GWP refrigerant systems. This report shows that using 5 mm diameter tubes in heat exchangers is a feasible approach to develop heat pumps with low-GWP refrigerants. Using the proposed design approach can yield higher system efficiency with lower environmental impact.

42 ENGINEERING↗

Biopolymer-supramolecular polymer hybrids for photocatalytic hydrogen production

Solar generation of H 2 is a promising strategy for dense energy storage. Supramolecular polymers composed of chromophore amphiphile monomers containing perylene monoimide (PMI) have been reported as crystalline light-harvesting assemblies for aqueous H 2 -evolving catalysts. Gelation of these supramolecular polymers with multivalent ions creates hydrogels with high diffusivity but insufficient mechanical stability and catalyst retention for reusability. We report here on using sodium alginate (SA) biopolymer to both induce supramolecular polymerization of PMI and co-immobilize them with catalysts in a robust hydrogel with high diffusivity that can also be 3D-printed. Faster mass transfer was achieved by controlling the material macrostructure by reducing gel diameter and microstructure by reducing biopolymer loading. Optimized gels produce H 2 at rates rivaling solution-based PMI and generate H 2 for up to 6 days. The PMI assemblies in the SA matrix create a percolation network capable of bulk-electron transfer under illumination. These PMI–SA materials were then 3D-printed on conductive substrates to create 3D hydrogel photoelectrodes with optimized porosity. The design of these versatile hybrid materials was bioinspired by the soft matter environment of natural photosynthetic systems and opens the opportunity to carry out light-to-fuel conversion within soft matter with arbitrary shapes and particular local environments.

36 MATERIALS SCIENCE↗

High-temperature, irradiation-resistant thermocouple, coaxial thermocouple, and related methods

A coaxial thermocouple includes a wire, an insulation layer surrounding the wire, a sheath surrounding the insulation layer, and an electrical junction formed between the wire and the sheath and at one longitudinal end of the coaxial thermocouple, the electrical junction including a swaged end with an outer diameter of the sheath reducing in diameter along a longitudinal length of the coaxial thermocouple until the sheath contacts the wire within the insulation layer. The wire includes a first material and the sheath includes a second material where the first material includes one of molybdenum (Mo) or niobium (Nb) and the second material includes the other of molybdenum (Mo) or niobium (Nb).

Skifton, Richard S.↗

Effect of reducing rotor blade inlet diameter on the performance of a 11.66-Centimeter radial-inflow turbine

The effect of increased rotor blade loading on turbine performance was investigated by reducing rotor blade inlet diameter. The reduction was made in four stages. Each modification was tested with the same stator using cold air as the working fluid. Results are presented in terms of equivalent mass flow and efficiency at equivalent design rotative speed and over a range of pressure ratios. Internal flow characteristics are shown in terms of stator exit static pressure and the radial variation of local loss and rotor-exit flow angle with radius ratio. Included are velocity diagrams calculated from the experimental results.

Kofskey, M. G.↗

Codoping of magnesium with oxygen in gallium nitride nanowires

Co-doping of p-type GaN nanowires with Mg and oxygen was investigated using first-principles calculations. The Mg becomes a deep acceptor in GaN nanowires with high ionization energy due to the quantum confinement. The ionization energy of Mg doped GaN nanowires containing passivated Mg-O complex decreases with increasing the diameter, and reduces to 300 meV as the diameter of the GaN nanowire is larger than 2.01 nm, which indicates that Mg-O co-doping is suitable for achieving p-type GaN nanowires with larger diameters. The co-doping method to reduce the ionization energy can be effectively used in other semiconductor nanostructures.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Flight investigation of an underwing nacelle installation of three variable-flap ejector nozzles

A modified F-106B aircraft with underwing engine nacelles was flight tested to investigate airframe installation effects on ejector nozzles. Nozzle thrust coefficients, boattail drag coefficients, and boundary layer characteristics were obtained for the three nozzles. All the nozzles were geometrically similar and had 15 deg conical boattails with juncture radii of curvature equal to 0.5 maximum nozzle diameter. The effects of boattail location relative to the wing trailing edge and the ejector to primary nozzle exit diameter ratio were investigated. Shortening the length by 0.48 nozzle diameter lowered the transonic boattail drag rise Mach number from 0.97 to 0.95. Decreasing the nozzle exit diameter, which reduced the ejector to primary nozzle exit diameter ratio from 1.30 to 1.18, increased the gross thrust coefficient 4.8 percent.

Head, V. L.↗

Auxiliary propulsion thruster performance with ion machined accelerator grids

A substantial improvement in the performance of an 8-centimeter-diameter auxiliary propulsion thruster was achieved by reducing the diameter of the accelerator grid apertures. The accelerator grid hole geometry was defined by ion machining accelerator grids on an 8-centimeter thruster at thrust levels of 2.2, 4.4, and 6.7 millinewtons was (mN). A thruster with an ion machined accelerator grid was operated at a thrust of 4.4 mN for 1000 hours. The discharge propellant utilization was 92% at an eV/ion of 338. Thruster performance and accelerator grid hole geometry was documented as a function of thrust level. It was also determined that the small hole accelerator grid has a very low backstreaming voltage limit. In fact the thruster can be operated with the acclerator grid held at neutralizer tip potential.

Hudson, W. R.↗

Anomalous diameter dependence of thermal transport in ultra-narrow Si nanowires

We present atomistic valence force field calculations of thermal transport in Si nanowires of diameters from 12 nm down to 1 nm. We show that as the diameter is reduced, the phonon density-of-states and transmission function acquire a finite value at low frequency, in contrast to approaching zero as in the bulk material. It turns out that this effect results in what Ziman described as the “problem of long longitudinal waves” [J. M. Ziman, Electrons and Phonons: The Theory of Transport Phenomena in Solids (Clarendon, Oxford, 1962)], which states that the thermal conductivity of a material increases as its length is increased due to the vanishing scattering for long-wavelength phonons. We show that this thermal transport improvement also appears in nanowires as their diameter is decreased below D = 5 nm (not only as the length increases), originating from the increase in the density of the long wavevector modes. The observation is present under ballistic transport conditions, and further enhanced with the introduction of phonon-phonon scattering. Because of this, in such ultra-narrow nanowires, as the diameter is reduced, phonon transport is dominated more and more by lower energy phonons with longer mean-free paths. We show that ∼80% of the heat is carried by phonons with energies less than 5 meV, most with mean-free paths of several hundreds of nanometers.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Auxiliary propulsion thruster performance with ion machined accelerator grids

A substantial improvement in the performance of an 8-centimeter-diameter auxiliary propulsion thruster has been achieved by reducing the diameter of the accelerator grid apertures. The accelerator grid hole geometry has been defined by ion machining accelerator grids on an 8-centimeter thruster at thrust levels of 2.2, 4.4, and 6.7 millinewtons (mN). A thruster with an ion machined accelerator grid has been operated at a thrust of 4.4 mN for 1000 hours. The discharge propellant utilization was 92% at an eV/ion of 338. Thruster performance and accelerator grid hole geometry has been documented as a function of thrust level. It was also determined that the small hole accelerator grid has a very low backstreaming voltage limit. In fact the thruster can be operated with the accelerator grid held at neutralizer tip potential.

Hudson, W. R.↗

Axisymmetric bluff-body drag reduction using circumferential grooves

The effect of shoulder radiusing and circumferentially grooving the afterbodies of bluff bodies to reduce the base drag at low speeds is discussed. Shoulder radii as large as 2.75 body diameters are examined. Reynolds number based on body diameter varied from 20,000 to 200,000. Results indicate that increasing the shoulder radius to 2.75 body diameters can reduce the drag levels to those of a streamline body having 67 percent greater fineness ratio. For zero shoulder radius, circumferential grooves were found to be effective in reducing body drag for zero shoulder radius in both laminar and tripped flow. Circumferential grooves on the afterbody with a shoulder radius of one-half the body diameter were only effective in reducing drag for laminar flow.

Howard, F. G.↗

Changes in Prostate Shape and Volume and Their Implications for Radiotherapy After Introduction of Endorectal Balloon as Determined by MRI at 3T

Purpose: To determine the changes in prostate shape and volume after the introduction of an endorectal coil (ERC) by means of magnetic resonance imaging (MRI) at 3T. Methods and materials: A total of 44 consecutive patients with biopsy-proven prostate cancer underwent separate MRI examinations at 3T with a body array coil and subsequently with an ERC inflated with 50 mL of fluid. Prospectively, two experienced readers independently evaluated all data sets in random order. The maximal anteroposterior, right-to-left, and craniocaudal prostate diameters, as well as the total prostate and peripheral zone and central gland volumes were measured before and after ERC introduction. The changes in prostate shape and volume were analyzed using Wilcoxon's test for paired samples. Results: The introduction of the ERC significantly changed the prostate shape in all three directions, with mean changes in the anteroposterior, right-to-left, and craniocaudal diameters of 15.7% (5.5 mm), 7.7% (3.5 mm), and 6.3% (2.2 mm), respectively. The mean total prostate, peripheral zone, and central gland volume decreased significantly after ERC introduction by 17.9% (8.3 cm{sup 3}), 21.6% (4.8 cm{sup 3}), and 14.2% (3.4 cm{sup 3}), respectively. Conclusion: ERC introduction as observed by 3T MRI changed the prostate shape and volume significantly. The mean anteroposterior diameter was reduced by nearly one-sixth of its original diameter, and the mean total prostate volume was decreased by approximately 18%. This could cause difficulties and should be considered when using ERC-based MRI for MRI-computed tomography fusion and radiotherapy planning.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Gain Filtering for Single-Spatial-Mode Operation of Large-Mode-Area Fiber Amplifiers

Gain filtering of higher order modes in large-mode-area fibers is an extremely robust method for providing diffraction-limited performance regardless of core diameter or input beam quality. Analytic calculations demonstrate that reducing the diameter of the gain dopants compared to the waveguide diameter produces differential gain that is higher for the fundamental mode than all other fiber modes at all saturation levels. Matching the gain dopant to the mode profile is not as beneficial as a simple step profile since the primarymechanism of gain filtering is to deny gain toward the edge of the waveguide where most of the higher order mode power is contained. Numerical simulations of multikilowatt fiber amplifiers with up to 100-μm-diameter cores show that gain filtering is extremely robust, providing 99% of the output power in the fundamental mode output with only 90% of the seed power in the fundamental mode. Even with poor seed launch with 50% of the power in the fundamental mode, gain filtering can provide up to 90% of the output power in the fundamental mode.

fiber amplifiers↗

Metal tube reducer is inexpensive and simple to operate

Low-cost metal tube reducer accepts tubing up to 1 inch outer diameter and can reduce this diameter to less than 1/2 inch with controlled wall thickness. This device can reduce all of the tube without waste. It produces extremely good surface finishes.

Mayfield, R. M.↗

Laser-Beam Zooming to Mitigate Crossed-Beam Energy Losses in Direct-Drive Implosions

In this study, spherically symmetric direct-drive-ignition designs driven by laser beams with a focal-spot size nearly equal to the target diameter suffer from energy losses due to crossed-beam energy transfer (CBET). Significant reduction of CBET and improvements in implosion hydrodynamic efficiency can be achieved by reducing the beam diameter. Narrow beams increase low-mode perturbations of the targets because of decreased illumination uniformity that degrades implosion performance. Initiating an implosion with nominal beams (equal in size to the target diameter) and reducing the beam diameter by ~ 30% - 40% after developing a sufficiently thick target corona, which smooths the perturbations, mitigate CBET while maintaining low-mode target uniformity in ignition designs with a fusion gain >> 1.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Reduction of Orifice-Induced Pressure Errors

Use of porous-plug orifice reduces or eliminates errors, induced by orifice itself, in measuring static pressure on airfoil surface in wind-tunnel experiments. Piece of sintered metal press-fitted into static-pressure orifice so it matches surface contour of model. Porous material reduces orifice-induced pressure error associated with conventional orifice of same or smaller diameter. Also reduces or eliminates additional errors in pressure measurement caused by orifice imperfections. Provides more accurate measurements in regions with very thin boundary layers.

Plentovich, Elizabeth B.↗