Search NASA⌕ Search

SEARCH · Search NASA

Results for “SELF OPERATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Optimal control of distributed parameter elastic systems

This paper presents an analytical solution to the Riccati equation for self-adjoint systems such as beams, plates, strings and membranes moving in space, and shows how the optimal control law can be implemented using the given solution. It is then shown that there always exists a self-adjoint operator describing the distribution of potential energy if the state space is appropriately augmented. A beam-like gravity-stabilized satellite moving in a circular orbit around the earth is used to illustrate the main results in this paper.

Juang, J.-N.↗

Data systems - Optical bus will connect distributed system

The fiber optics buses currently under consideration for the NASA space station program will have data rates of at least 20 Mb/sec. The network interconnection scheme that will eventually be used is, however, uncertain. A NASA-Langley effort on graph networks includes adaptive, fault-tolerant and self-correcting operations. A breadboard program at NASA-Johnson includes evaluations of standard devices, called 'bus interface units', in an adaptive and fault-correcting chordal or concentric ring type of network. Fiber optics would allow an evolution to wavelength modulation techniques in such systems.

Swingle, W. L.↗

International test and demonstration of a 1-MW wellhead generator: Helical screw expander power plant

A 1-MW wellhead generator was tested in 1980, 1981, and 1982 by Mexico, Italy, and New Zealand at Cerro Prieto, Cesano, and Broadlands, respectively. The total flow helical screw expander portable power plant, Model 76-1, had been built for the U.S. Government and field-tested in Utah, USA, in 1978 and 1979. The expander had oversized internal clearances designed for self-cleaning operation on fluids that deposit adherent scale normally detrimental to the utiliation of liquid dominated fields. Conditions with which the expander was tested included inlet pressures of 64 to 220 psia, inlet qualities of 0% to 100%, exhaust pressures of 3.1 to 40 psia, electrial loads of idle and 110 to 933 kW, electrical frequencies of 50 and 60 Hz, male rotor speeds of 2500 to 4000 rpm, and fluid characteristics to 310,000 ppm total dissolved solids and noncondensables to 38 wt % of the vapor. Some testing was done on-grid. Typical expander isentropic efficiency was 40% to 50% with the clearances not closed, and 5 percentage points or more higher with the clearances partly closed. The expander efficiency increased approximately logarithmically with shaft power for most operations, while inlet quality, speed, and pressure ratio across the machine had only small effects. These findings are all in agreement with the Utah test results.

Mckay, R. A.↗

Actuator Feasibility Study for Active Control of Ducted Axial Fan Noise

A feasibility study was performed to investigate actuator technology which is relevant for a particular application of active noise control for gas turbine stator vanes. This study investigated many different classes of actuators and ranked them on the order of applicability. The most difficult requirements the actuators had to meet were high frequency response, large amplitude deflections, and a thin profile. Based on this assessment, piezoelectric type actuators were selected as the most appropriate actuator class. Specifically, Rainbows (a new class of high performance piezoelectric actuators), and unimorphs (a ceramic/metal composite) appeared best suited to the requirements. A benchtop experimental study was conducted. The performance of a variety of different actuators was examined, including high polymer films, flextensional actuators, miniature speakers, unimorphs, and Rainbows. The displacement/frequency response and phase characteristics of the actuators were measured. Physical limitations of actuator operation were also examined. This report includes the first known, high displacement, dynamic data obtained for Rainbow actuators. A new "hard" ceramic Rainbow actuator which does not appear to be limited in operation by self heating as "soft" ceramic Rainbows was designed, constructed and tested. The study concludes that a suitable actuator for active noise control in gas turbine engines can be achieved with state of the art materials and processing.

Simonich, John C.↗

Self-Sustained Ultrafast Pulsation in Coupled VCSELs

High frequency, narrow-band self-pulsating operation is demonstrated in two coupled vertical-cavity surface-emitting lasers (VCSELs). The coupled VCSELs provide an ideal source for high-repetition rate (over 40 GHz), sinusoidal-like modulated laser source with Gaussian-like near- and far-field profiles. We also show that the frequency of the modulation can be tuned by the inter-VCSEL separation or by DC-bias level.

Ning, Cun-Zheng↗

Functional Allocation with Airborne Self-Separation Evaluated in a Piloted Simulation

A human-in-the-loop simulation experiment was designed and conducted to evaluate an airborne self-separation concept. The activity supports the National Aeronautics and Space Administration s (NASA) research focus on function allocation for separation assurance. The objectives of the experiment were twofold: (1) use experiment design features in common with a companion study of ground-based automated separation assurance to promote comparability, and (2) assess agility of self-separation operations in managing trajectory-changing events in high traffic density, en-route operations with arrival time constraints. This paper describes the experiment and presents initial results associated with subjective workload ratings and group discussion feedback obtained from the experiment s commercial transport pilot participants.

Wing, David J.↗

Design of Rigid-Flex PCB Robotics Leveraging Validated Finite Element Simulations

The use of rigid-flex printed circuit board (PCB) as primary structure has the potential to reduce the weight and volume of robotic systems. In the case of robotics for interplanetary exploration, these systems can leverage origami-inspired folding for increased mobility options and reduced storage volume. Folding rigid-flex PCB robotics can be constructed with rigid PCB connected by short Nomex fabric hinges coupled with flex PCB ribbon cables that permits enhanced system flexibility and energy dissipation to promote impact survivability. This paper presents a design methodology of rigid-flex PCB systems with an emphasis on impact resistance. The design process considers solder joint adequacy, panel bending, and fracture using a finite element (FE) model. The proposed design methodology is developed using a case study with NASA JPL's Pop-Up Folding Flat Explorer Robot (PUFFER). First, the finite-element (FE) modeling methodology is presented with consideration to both frequency and time-domain modeling applications, which include operational self-contact analysis and high impact scenarios. The time-domain impact modeling methodology utilizes hyperelastic material properties for the Nomex hinges. This modeling method is validated using image correlation of PUFFER drop tests. A flowchart is presented to guide users through a validated Abaqus modeling procedure for highly flexible rigid-flex systems. Next, a case study is presented in which PUFFER is subject to drop heights representative of falls into Lunar pits and then the design is refined for a more optimum impact performance. Finally, the results of the case study are used to inform a generalized design methodology for rigid-flex PCB robotics subject to high-impact loads with the considerations presented.

John Bell↗

Design of Rigid-Flex PCB Robotics Leveraging Validated Finite Element Simulations

The use of rigid-flex printed circuit board (PCB) as primary structure has the potential to reduce the weight and volume of robotic systems. In the case of robotics for interplanetary exploration, these systems can leverage origamiinspired folding for increased mobility options and reduced storage volume. Folding rigid-flex PCB robotics can be constructed with rigid PCB connected by short Nomex fabric hinges coupled with flex PCB ribbon cables that permits enhanced system flexibility and energy dissipation to promote impact survivability. This paper presents a design methodology of rigidflex PCB systems with an emphasis on impact resistance. The design process considers solder joint adequacy, panel bending, and fracture using a finite element (FE) model. The proposed design methodology is developed using a case study with NASA JPL’s Pop-Up Folding Flat Explorer Robot (PUFFER). First, the finite-element (FE) modeling methodology is presented with consideration to both frequency and time-domain modeling applications, which include operational self-contact analysis and high impact scenarios. The time-domain impact modeling methodology utilizes hyperelastic material properties for the Nomex hinges. This modeling method is validated using image correlation of PUFFER drop tests. A flowchart is presented to guide users through a validated Abaqus modeling procedure for highly flexible rigid-flex systems. Next, a case study is presented in which PUFFER is subject to drop heights representative of falls into Lunar pits and then the design is refined for a more optimum impact performance. Finally, the results of the case study are used to inform a generalized design methodology for rigid-flex PCB robotics subject to high-impact loads with the considerations presented.

de la Croix, Jean-Pierre↗

Looking to the Future: A Call to Action for Advanced GNC Algorithm Verification and Validation

Future space systems will rely on autonomous Guidance, Navigation, and Control (GNC) functions to efficiently manage safe and precise self-directed operations in uncertain complex environments. Fundamentally, the GNC system plays a key role in mission performance and safety because it computes the ideal trajectory (Guidance), determines the actual trajectory (Navigation), and executes the ideal trajectory (Control) of a vehicle’s position and attitude. Our current GNC systems are highly automated and already have a high degree of complexity. As missions become more ambitious, GNC systems for launch vehicles and space platforms (e.g., spacecraft, probes, and landers) will require higher levels of performance and autonomous operation than previously encountered, for example, this includes GNC for optimizing aerodynamic and/or propulsion performance during planetary entry. This GNC Verification and Validation (V&V) paper highlights concerns with what undoubtedly will be a trend towards increased complexity as fully autonomous GNC systems are developed for future space missions. Clearly, complex GNC systems pose challenges in the prelaunch V&V phase, which is a relatively expensive part of a mission’s life cycle. Essentially the V&V phase is focused on checking that the system effectively meets all the design and operational requirements for the mission. The authors of this paper (i.e., the Inter-Agency Working Group of GNC subject matter experts) focused on this fundamental question over the past few years: Will the GNC engineering community of practice be sufficiently prepared to perform the necessary V&V on evolving GNC architectures that are driven by very demanding requirements for autonomy, resiliency, reconfigurability, adaptability, and mission cost-benefit balance? It is the viewpoint of our Inter-Agency team that the GNC V&V approaches and processes needed to address the next generation of complex GNC systems, which likely will employ various forms of modern GNC technology, are not currently established to the level the community will need in the future. While researchers and practitioners have made some progress in developing new GNC V&V methods for modern GNC systems, a good deal of work remains to be done to codify such methods in a comprehensive and systematic manner. Thus, the Inter-Agency team’s partner organizations [the National Aeronautics and Space Administration (NASA), the European Space Agency (ESA), the National Centre for Space Studies (CNES), the German Aerospace Center (DLR), the French Aerospace Lab (ONERA), and ISAE-SUPAERO] have conducted preliminary investigations into advancing GNC V&V techniques, which resulted in the identification of the need for education, new V&V tools, and benchmark problems for the GNC community. The necessary proactive steps to be taken to meet the challenges and fill the gaps in GNC V&V are summarized in this paper. The first steps include identifying advanced analysis tools, developing a GNC V&V roadmap, and expanding education and training programs for GNC practitioners. This paper is a call to action and proposes a comprehensive set of recommended actions for all our stakeholders: space agencies, researchers, and industry.

Samir Bennani↗

Complete high temperature test of neutron flux sensors in NRAD

The purpose of this test was to characterize operation of Self Powered Neutron Detectors (SPNDs) at high temperature and shake out any bugs in the data acquisition equipment prior to testing at higher flux in MITR.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

GrayQb: A Radiological Contamination Locating and Mapping Tool

Benefits Technology Overview  Easy to operate • Self-contained unit for imaging – no special power, cooling or handling requirements • Standard color camera, easy to use gamma camera and reader • Software automatically processes images, sliders to adjust intensity display • Lightweight – less than 5 lbs. without additional background shielding

Timmons, Daren↗

Design study of shaft face seal with self-acting lift augmentation. 5: Performance in simulated gas turbine engine operation

The feasibility and the noncontact operation of the self-acting seal was demonstrated over a range of simulated gas turbine engine conditions from 200 to 500 ft/sec sliding speed. Sealed pressure differentials were 50 to 300 psi and sealed temperatures were 150 to 1200 F. Low leakage (about 1/10 that of conventional labyrinth seals) was exhibited in two endurance runs (200 and 338 hr) at 400 ft/sec, 200 psi and 1000 F (gas temperature). For these endurance runs, the self-acting pad wear was less than 3.8 micrometers (0.00015 in.); this low wear was attributed to the noncontact operation of the primary seal. Operating problems identified were fretting wear of the secondary seal and erosion of the primary seal by hard particles.

Ludwig, L. P.↗

Self-Examination

The operation of the new U.S./Canadian Orbiter Boom Sensor System (OBSS) by the STS-114 Discovery's crew "will be the most complicated space robotics job of the shuttle program," say Paul Hill, lead flight director. The OBSS is a laser-and-imaging-sensor- equipped 50-ft. extension to the existing 50-ft. arm, increasing the shuttle's reach to 100 ft. The return-to-flight mission will debut the autonomous robotic self-inspection capability to detect and possibly aid the repair of the type of damage that doomed Columbia and her crew, were it to occur again. With 3D imaging and laser contour-mapping capability, the OBSS will enable the diagnosis of cracks in reinforced carbon-carbon (RCC) wing and nose areas and thermal protection system (TPS) tiles beyond the view of the standard manipulator arm. Given the major changes to the shuttle external tank, no damage is expected. But the OBSS is a direct response to the Columbia Accident Investigation Board's recommendations. The new boom and a significant amount of its supporting software was developed by MacDonald Dettwiler heads. Space and Advanced Robotics Ltd. (MD Robotics) in Brampton, Ontario, a key contractor in the shuttle program for 25 years. The Canadian Space Agency is also heavily involved in supporting shuttle and International Space Station (ISS) robotics.

Covault, Craig↗

Operation of Grid Forming Converters as Self Excited Induction Generators Under Non-Ideal Loading Conditions

Self-excited induction generators offer a robust solution for power production for standalone as well as grid-connected systems. In general, self-excited induction generators require excitation capacitors which make use of the machine magnetization characteristics for voltage build up process as well as operation at a specific frequency. In this paper, a self-excited induction machine is modeled with both the electrical and mechanical dynamics. This modeled virtual machine's dynamics are utilized for voltage build up process for a standalone photovoltaic converter connected to a local load for a microgrid application. The modeled machine's parameters are used from the name plate rating from the manufacturer. However, in a microgrid the accommodation of unbalanced and/or nonlinear harmonic rich load is a necessity, therefore, in this work the virtual self-excitation capacitors of the modeled machine are varied based on the machine characteristics. With the objective of ensuring harmonic free point of common coupling voltage, the modeled virtual self-excitation capacitors are varied to accomplish change in terminal frequency and the virtual load torque is varied to obtain voltage magnitude change. To verify the efficacy, the overall system is modeled in MATLAB/Simulink and PLECS domain and most important case studies are presented.

grid forming converters (GFM)↗

Utilization of the CW magnetrons as coherent RF sources for superconducting RF accelerators

CW magnetrons designed and optimized for industrial heaters, driven by an injection-locking signal, were suggested to power Superconducting RF (SRF) cavities. However, the CW magnetrons, which are regenerative generators, are intended to operate in self-excitation mode, so, for reliable starting they use a large regenerative gain, causing a large regenerative instability in operation. Thus, power supply ripple, even shot noise, etc., lead to multiple sidebands forming a quasi-continuous noise spectrum at the carrier frequency. Therefore, in the traditionally used mode of operation and control, such magnetrons are inapplicable for powering high Q-factor SRF cavities. A new approach to operation and control of CW magnetrons considering non-stationary processes during start-up and operation makes it possible to find a mode of almost coherent RF generation of tubes with a significant reduction in regenerative instability and noise and increased efficiency. In our work is presented substantiation for the newly developed mode with an analysis of the new approach based on experimental results. •In this article, for the first time, non-stationary, regenerative processes are considered during the start-up and operation of CW magnetrons for powering high-Q superconducting RF cavities.•An analytical study, confirmed by experiments, showed that the traditionally used modes of starting and operating CW magnetrons are not suitable for powering high-Q superconducting RF cavities.•In fact, to make CW magnetrons suitable for such cavities, the physics of starting and operating CW magnetrons must be changed. This has been demonstrated in our work.•In developing the Stimulated Coherent Generation Mode [NIM A 980 (2020) 164366], we have shown the suitability of this mode for starting and operating CW magnetrons for high-Q superconducting RF cavities.•Analytical analysis, verified experimentally, substantiates in our article the suitability of the “Mode of stimulated coherent generation” of CW magnetrons for powering high-Q superconducting cavities in pulsed and continuous modes.

43 PARTICLE ACCELERATORS↗

Extending Validated Human Performance Models to Explore NextGen Concepts

To meet the expected increases in air traffic demands, NASA and FAA are researching and developing Next Generation Air Transportation System (NextGen) concepts. NextGen will require substantial increases in the data available to pilots on the flight deck (e.g., weather,wake, traffic trajectory predictions, etc.) to support more precise and closely coordinated operations (e.g., self-separation, RNAV/RNP, and closely spaced parallel operations, CSPOs). These NextGen procedures and operations, along with the pilot's roles and responsibilities, must be designed with consideration of the pilot's capabilities and limitations. Failure to do so will leave the pilots, and thus the entire aviation system, vulnerable to error. A validated Man-machine Integration and design Analysis System (MIDAS) v5 model was extended to evaluate anticipated changes to flight deck and controller roles and responsibilities in NextGen approach and Land operations. Compared to conditions when the controllers are responsible for separation on decent to land phase of flight, the output from these model predictions suggest that the flight deck response time to detect the lead aircraft blunder will decrease, pilot scans to the navigation display will increase, and workload will increase.

Gore, Brian Francis↗

Dynamic Routing for Delay-Tolerant Networking in Space Flight Operations

Computational self-sufficiency - the making of communication decisions on the basis of locally available information that is already in place, rather than on the basis of information residing at other entities - is a fundamental principle of Delay-Tolerant Networking. Contact Graph Routing is an attempt to apply this principle to the problem of dynamic routing in an interplanetary DTN. Testing continues, but preliminary results are promising.

CGR↗

Self-acting shaft seals

Report reviews operating principles and design of self-acting seals. Influences of adverse operating conditions are considered also. Elements of analysis used in seal performance predictions are described and evaluated. Mathematical models for obtaining seal force balance and equilibrium film thickness are outlined. Self-acting seals are nonrubbing, have lower leakage rates than labyrinth seals, and are well suited for advanced aircraft engines.

Ludwig, L. P.↗