Search NASA⌕ Search

SEARCH · Search NASA

Results for “SILICON COMPOUND”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Checking Surface Contours

Rubber impressions viewed with optical comparator. Simple mold constructed from aluminum sheet or any other easily shaped material compatible with silicone rubber ingredients. Mold placed over surface to be measured. Newly-mixed silicone rubber compound poured in mold and allowed to cure.

Velega, D.↗
NASA NTRS1986

Documentation of ice shapes accreted on the main rotor of a UH-1H helicopter in level flight

Icing tests were conducted on a UH-1H helicopter in level flight behind a spray tanker near Duluth, Minnesota, during the winter of 1983-84 as part of the joint NASA/Army HIFT program. On landing, the ice formations on the main rotor were documented by casting a set of ten-inch molds on the blade using a Dow-Corning silicone rubber compound which was initially liquid at sub-freezing temperatures. Such documentation was accomplished for eight flights in which the temperature ranged from -11 C to -22 C and the in-cloud flight times ranged from 5 to 9 minutes.

Hanson, M. K.↗
NASA NTRS1989

The behavior of SiC and Si3N4 ceramics in mixed oxidation/chlorination environments

The behavior of silicon-based ceramics in mixed oxidation/chlorination environments was studied. High pressure mass spectrometry was used to quantitatively identify the reaction products. The quantitative identification of the corrosion products was coupled with thermogravimetric analysis and thermodynamic equilibrium calculations run under similar conditions in order to deduce the mechanism of corrosion. Variations in the behavior of the different silicon-based materials are discussed. Direct evidence of the existence of silicon oxychloride compounds is presented.

Marra, John E.↗
NASA NTRS1992

Surface analysis of anodized aluminum clamps from NASA-LDEF satellite

Surface analysis results of selected anodized aluminum clamps containing black (Z306) and white (A276) paints which received nearly six years of Low Earth Orbit (LEO) exposure on the Long Duration Exposure Facility are reported. Surface analytical techniques, including x-ray photoelectron spectroscopy (XPS), Auger electron spectroscopy (AES), and scanning electron microscopy/energy dispersive analysis by x-ray (SEM/EDAX), showed significant differences in the surface composition of these materials depending upon the position on the LDEF. Differences in the surface composition are attributed to varying amounts of atomic oxygen and vacuum ultraviolet radiation (VUV). Silicon containing compounds were the primary contaminant detected on the materials.

Grammer, H. L.↗
NASA NTRS1993

Surface characterization of selected LDEF tray clamps

The surface characterization of chromic acid anodized 6061-T6 aluminum alloy tray clamps has shown differences in surface chemistry depending upon the position on the Long Duration Exposure Facility (LDEF). Water contact angle results showed no changes in wettability of the tray clamps. The overall surface topography of the control, trailing edge(E3) and leading edge(D9) samples was similar. The thickness of the aluminum oxide layer for all samples determined by Auger depth profiling was less than one micron. X-ray photoelectron spectroscopy (XPS) analysis of the tray clamps showed significant differences in the surface composition. Carbon and silicon containing compounds were the primary contaminants detected.

Cromer, T. F.↗
NASA NTRS1996

A Two Phase HfB2-SiB4 Material

A two phase HfB2-SiB4 material which is useful as a high temperature oxidation resistant coating. This invention relates to ceramic coatings and more particularly to ceramic coatings containing metal borides. Boride materials are known to have good oxidation resistance, with HfB2 considered to be the best pure boride for oxidation applications. It has been shown that the addition of 10 to 20 percent SiC to HfB2 increases the oxidation resistance. The HfB2-SiC materials are prepared by hot pressing powder mixtures. Hot pressing powder mixtures has limited ability to produce fine grained multiphase materials due to particle coarsening during the sintering process. Additionally, the purity of the final monolithic structure is limited to the purity of the starting powders. Chemical vapor deposition (CVD) offers a method of producing highly pure multiphase ceramics, with better control of microstructure. Researchers have tried to produce HfB2-SiC coatings by CVD but without success.

SILICON COMPOUNDS↗
NASA NTRS1995

Observations of chemical processing in the circumstellar environment

High resolution interferometer and single-dish observations of young, deeply embedded stellar systems reveal a complex chemistry in the circumstellar environments of low to intermediate mass stars. Depletions of gas-phase molecules, grain mantle evaporation, and shock interactions actively drive chemical processes in different regions around young stars. We present results for two systems, IRAS 05338-0624 and NCG 1333 IRAS 4, to illustrate the behavior found and to examine the physical processes at work.

NASA Program Exobiology↗
NASA NTRS2008

Experimental Investigation of Elastomer Docking Seal Compression Set, Adhesion, and Leakage

A universal docking and berthing system is being developed by the National Aeronautics and Space Administration (NASA) to support all future space exploration missions to low-Earth orbit (LEO), to the Moon, and to Mars. An investigation of the compression set of two seals mated in a seal-on-seal configuration and the force required to separate the two seals after periods of mating was conducted. The leakage rates of seals made from two silicone elastomer compounds, S0383-70 and S0899-50, configured in seal-on-seal mating were quantified. The test specimens were sub-scale seals with representative cross-sections and a 12 inch outside diameter. The leakage rate of the seals manufactured from S0899-50 was higher than that of the seals made from S0383-70 by a factor of 1.8. Similarly, the adhesion of the 50 durometer elastomer was significantly higher than that of the 70 durometer compound. However, the compression set values of the S0899-50 material were observed to be significantly lower than those for the S0383-70.

Daniels, Christopher C.↗
NASA NTRS2008

Characteristics of Elastomer Seals Exposed to Space Environments

A universal docking and berthing system is being developed by the National Aeronautics and Space Administration (NASA) to support all future space exploration missions to low-Earth orbit (LEO), to the Moon, and to Mars. The Low Impact Docking System (LIDS) is being designed to operate using a seal-on-seal configuration in numerous space environments, each having unique exposures to temperature, solar radiation, reactive elements, debris, and mission duration. As the LIDS seal is likely to be manufactured from an elastomeric material, performance evaluation of elastomers after exposure to atomic oxygen (AO) and ultraviolet radiation (UV) was conducted, of which the work presented herein was a part. Each of the three candidate silicone elastomer compounds investigated, including Esterline ELA-SA-401, and Parker Hannifin S0383-70 and S0899-50, was characterized as a low outgassing compound, per ASTM E595, having percent total mass loss (TML) less than 1.0 percent and collected volatile condensable materials (CVCM) less than 0.1 percent. Each compound was compatible with the LIDS operating environment of -50 to 50 C. The seal characteristics presented include compression set, elastomer-to-elastomer adhesion, and o-ring leakage rate. The ELA-SA-401 compound had the lowest variation in compression set with temperature. The S0383-70 compound exhibited the lowest compression set after exposure to AO and UV. The adhesion for all of the compounds was significantly reduced after exposure to AO and was further decreased after exposure to AO and UV. The leakage rates of o-ring specimens showed modest increases after exposure to AO. The leakage rates after exposure to AO and UV were increased by factors of up to 600 when compared to specimens in the as-received condition.

Daniels, Christopher C.↗
NASA NTRS2008

Performance of Subscale Docking Seals Under Simulated Temperature Conditions

A universal docking system is being developed by the National Aeronautics and Space Administration (NASA) to support future space exploration missions to low Earth orbit (LEO), to the moon, and to Mars. The candidate docking seals for the system are a composite design consisting of elastomer seal bulbs molded into the front and rear sides of a metal ring. The test specimens were subscale seals with two different elastomer cross-sections and a 12-in. outside diameter. The seal assemblies were mated in elastomer seal-on-metal plate and elastomer seal-on-elastomer seal configurations. The seals were manufactured from S0383-70 silicone elastomer compound. Nominal and off-nominal joint configurations were examined. Both the compression load required to mate the seals and the leak rate observed were recorded while the assemblies were subjected to representative docking system operating temperatures of -58, 73, and 122 F (-50, 23, and 50 C). Both the loads required to fully compress the seals and their leak rates were directly proportional to the test temperature.

Smith, Ian M.↗
NASA NTRS2010

Material Properties of Three Candidate Elastomers for Space Seals Applications

A next-generation docking system is being developed by the National Aeronautics and Space Administration (NASA) to support Constellation Space Exploration Missions to low Earth orbit (LEO), to the Moon, and to Mars. A number of investigations were carried out to quantify the properties of candidate elastomer materials for use in the main interface seal of the Low Impact Docking System (LIDS). This seal forms the gas pressure seal between two mating spacecraft. Three candidate silicone elastomer compounds were examined: Esterline ELA-SA-401, Parker Hannifin S0383-70, and Parker Hannifin S0899-50. All three materials were characterized as low-outgassing compounds, per ASTM E595, so as to minimize the contamination of optical and solar array systems. Important seal properties such as outgas levels, durometer, tensile strength, elongation to failure, glass transition temperature, permeability, compression set, Yeoh strain energy coefficients, coefficients of friction, coefficients of thermal expansion, thermal conductivity and diffusivity were measured and are reported herein.

Bastrzyk, Marta B.↗
NASA NTRS1998

Space Suit Survivability Enhancement NASA Research Announcement 96-OLMSA-01B: Advanced Life Support and Environmental Technologies for Human Exploration and Development of Space

Conducted two meetings to review the project scope and develop concepts for self-sealing material compositions, Focus has been on developing concepts that would seal a penetration enough to allow the astronauts to re-enter the spacecraft within the window provided by the emergency air supply. Concepts discussed include: quilted fabrics containing a viscous flow material in the quilted cells which would seal the bladder breach when forced to flow by the internal suit pressure; a sealant impregnated felt liner which acts similar to above; and a "blousy" fibrous layer which would mechanically plug a rupture under pressure. Illustrations of the above concepts are included in the attached viewgraphs, which were used in a presentation. The most promising of these concepts will be made into prototypes for testing. ILC has developed a test fixture to test the scaling characteristics of various material layups by measuring real-time changes in pressure and make-up flow in a pressurized cylinder. Candidate viscous sealing compounds such as silicones and urethanes have been identified. These compounds will be coated on existing bladder cloth for initial tests. The most promising compounds will be integrated into the above material structures for final testing. Design and analysis of fabric weaves to improve cut and puncture resistance of the suit TMG layers is underway. Philadelphia Textile is developing a mathematical model to correlate yarn type and weave structure to cut and tear resistance. The computer mathematical modeling of the fabric failure mechanisms by Cornell University, as originally proposed, will be replaced with the above model and empirical testing methods, due to the loss of key Cornell personnel.

Source record↗
DOE OSTI2024

Effects of Structure and Filler on Mechanical Properties of Direct Ink Write Pads

Direct ink write (DIW) is an extrusion-based additive manufacturing (AM) technique that enables superior repeatability, property tuning, and material customization compared to conventional manufacturing techniques. In this research, DIW is used to print silicone foams that must accommodate the thermal expansion of other parts. This expansion requires the material to compress and subsequently recover. Thus, a key performance metric is reducing “compression set” or deformation retained after the material is compressed. For this study, a silicone resin was compounded with a getter material, 1,4 bis(phenylethynyl)benzene (DEB) mixed with carbon-supported palladium (Pd) and printed in a variety of lattice structures. The effects of the filler and print structure on compression set were evaluated. In these experiments, 0.5-inch diameter coupons were compressed to 75% their original height for 22 hours at 70 °C, and the change in height calculated at intervals between 30 minutes and 24 hours post-decompression. The unfilled pad with skin layers had the best compression set at 0.7% ± 0.1%, followed by the unfilled pad with no skins at 1.5% ± 0.1%. As the number of filled layers increased, compression set performance degraded. The pad with filled skin layers and all filled layers had a compression set of 7.0% ± 0.3%. Additionally, the reaction extent of DEB was found to increase compression set, possibly due to the diffusion of DEB to the surface at elevated temperatures. Imaging reveals extensive crystallization at the surface. These investigations show that a non-reinforcing filler will increase compression set but that print structure can mitigate this effect.

36 MATERIALS SCIENCE↗