Search NASA⌕ Search

SEARCH · Search NASA

Results for “SINTERED INTERFACES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Modeling of flash sintering of ionic ceramics

A fundamental understanding of the influence of defects in ionic ceramics at the atomic, microstructural, and macroscopic levels, before, during, and after the flash sintering event is key to the development of ceramic processing operations that lead to fast, low cost, and environmentally safe fabrication of materials. The observed phenomenology of the flash process encompasses multiple time and length scales and have resulted on a wide variety of what sometimes appears to be contradictory explanations. Here, this article summarizes the latest developments on the modeling and simulation of flash sintering, specifically those related to the understanding of the equilibrium and kinetic properties and the corresponding microstructural evolution of ionic ceramics. Challenges and opportunities in the development of theoretical analyses that include unidentified multiphysical effects are discussed, as they pertain to the processing of technologically relevant ceramic materials for advanced structures and devices.

36 MATERIALS SCIENCE↗

KNN–NTK composite lead-free piezoelectric ceramic

A (K,Na)NbO₃-based lead-free piezoelectric ceramic was successfully densified. It exhibited an enhanced electromechanical coupling factor of kₚ=0.52, a piezoelectric constant d₃₃=252 pC/N, and a frequency constant Nₚ=3170 Hz m because of the incorporation of an elaborate secondary phase composed primarily of KTiNbO₅. The ceramic's nominal composition was 0.92K₀.₄₂Na₀.₄₄Ca₀.₀₄Li₀.₀₂Nb₀.₈₅O₃–0.047K₀.₈₅Ti₀.₈₅Nb₁.₁₅O₅–0.023BaZrO₃ –0.0017Co₃O₄–0.002Fe₂O₃–0.005ZnO, abbreviated herein as KNN–NTK composite. The KNN–NTK ceramic exhibited a dense microstructure with few microvoids which significantly degraded its piezoelectric properties. Elemental maps recorded using transmission electron microscopy with energy-dispersive X-ray spectroscopy (TEM–EDS) revealed regions of high concentrations of Co and Zn inside the NTK phase. In addition, X-ray diffraction patterns confirmed that a small portion of the NTK phase was converted into K₂(Ti,Nb,Co,Zn)₆O₁₃ or CoZnTiO₄ by a possible reaction between Co and Zn solutes and the NTK phase during a programmed sintering schedule. TEM studies also clarified a distortion around the KNN/NTK interfaces. Such an NTK phase filled voids between KNN particles, resulting in an improved chemical stability of the KNN ceramic. The manufacturing process was subsequently scaled to 100 kg per batch for granulated ceramic powder using a spray-drying technique. The properties of the KNN–NTK composite ceramic produced using the scaled-up method were confirmed to be identical to those of the ceramic prepared by conventional solid-state reaction sintering. Consequently, slight changes in the NTK phase composition and the distortion around the KNN/NTK interfaces affected the KNN–NTK composite ceramic's piezoelectric characteristics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Flexible Thermoelectric Devices of Ultrahigh Power Factor by Scalable Printing and Interface Engineering

Printing is a versatile method to transform semiconducting nanoparticle inks into functional and flexible devices. In particular, thermoelectric nanoparticles are attractive building blocks to fabricate flexible devices for energy harvesting and cooling applications. However, the performance of printed devices are plagued by poor interfacial connections between nanoparticles and resulting low carrier mobility. While many rigid bulk materials have shown a thermoelectric figure of merit ZT greater than unity, it is an exacting challenge to develop flexible materials with ZT near unity. Here, a scalable screen-printing method to fabricate high-performance and flexible thermoelectric devices is reported. A tellurium-based nanosolder approach is employed to bridge the interfaces between the BiSbTe particles during the postprinting sintering process. The printed BiSbTe flexible films demonstrate an ultrahigh room-temperature power factor of 3 mW m -1 K -2 and ZT about 1, significantly higher than the best reported values for flexible films. A fully printed thermoelectric generator produces a high power density of 18.8 mW cm -2 achievable with a small temperature gradient of 80 °C. This screen-printing method, which directly transforms thermoelectric nanoparticles into high-performance and flexible devices, presents a significant leap to make thermoelectrics a commercially viable technology for a broad range of energy harvesting and cooling applications.

36 MATERIALS SCIENCE↗

Electrical conductivity of Ca{sub 1-x}Sr{sub x}Ti{sub 0.65}Fe{sub 0.35}O{sub 3-{delta}}, x = 0, 0.5 and 1, polycrystalline compounds in the 300-500 K range

Highlights: Black-Right-Pointing-Pointer Fe-doped Sr and Ca titanates were synthesized by chemical and solid state reaction. Black-Right-Pointing-Pointer SPM images show striking differences in samples prepared by the two routes. Black-Right-Pointing-Pointer Impedance spectroscopy measurements show different electrical behaviors. Black-Right-Pointing-Pointer Correlations between the two macroscopic observations are shown. -- Abstract: Bulk and grain boundary electrical conductivity of oxygen deficient Ca{sub x}Sr{sub 1-x}Ti{sub 0.65}Fe{sub 0.35}O{sub 3-{delta}}, x = 0, 0.5 and 1.0, polycrystalline specimens were evaluated by impedance spectroscopy measurements in the 5 Hz-13 MHz frequency range from 300 to 500 K. The ceramic powders were synthesized by solid state reaction and by a chemical route, the polymeric precursor technique. The X-ray diffraction of the samples at room temperature shows the following perovskite crystalline structures: cubic for x = 0 and orthorhombic for x = 0.5 and 1.0. The impedance plots are composed of two semicircles ascribed to grains (bulk) and interfaces (grain boundaries) contributions. The impedance data show that sintered pellets using powders prepared by solid state synthesis present higher intergranular and intragranular resistivity values than pellets prepared by the chemical route. Observations of scanning probe microscopy topographic images of the surfaces of the sintered pellets show evident differences between the grain morphology of the pellets prepared with powders synthesized by the two routes.

36 MATERIALS SCIENCE↗

Self-biased large magnetoelectric coupling in co-sintered Bi{sub 0.5}Na{sub 0.5}TiO{sub 3} based piezoelectric and CoFe{sub 2}O{sub 4} based magnetostrictive bilayered composite

In this work, magnetoelectric properties of a co-sintered bilayered composite of non-lead based piezoelectric 0.97(Bi{sub 0.5}Na{sub 0.5}TiO{sub 3})–0.03(K{sub 0.47}Na{sub 0.47}Li{sub 0.06}Nb{sub 0.74}Sb{sub 0.06}Ta{sub 0.2}O{sub 3}) and magnetostrictive Co{sub 0.6}Zn{sub 0.4}Fe{sub 1.7}Mn{sub 0.3}O{sub 4} are presented. Similar optimal sintering conditions of the individual components lead to a very clean interface as evidenced in the scanning electron microscopy, angle dispersive X-ray diffraction, and energy-dispersive X-ray (EDX) results. Clean interface results in strong intimate mechanical coupling between both components and causes a maximum transfer of induced strain, leading to a large magnetoelectric coupling ∼142 mV/cm·Oe measured in longitudinally magnetized-transversely polarized configuration (L-T mode). Remnant polarization ∼32 μC/cm{sup 2}, remnant magnetization ∼0.50 emu/g, and sufficiently high self biased magnetoelectricity ∼135 mV/cm Oe (L-T mode) were observed for this composite.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Effect of laser sintering on Ti-ZrB2 mixtures

Multi-layer structures of ZrB2 containing 30-70 weight percent (wt%) Ti was fabricated using laser sintering/melting technique. Ti acted as the binding interface for the hard ZrB2 particles. Structural properties and oxidation behavior of laser sintered samples were studied using high temperature X-ray diffraction (HTXRD). HTXRD revealed the formation of boride solid solutions (Zr0.61Ti0.39B2, Zr0.2Ti0.8B2), Zr0.3Ti0.7 and TiB whiskers as well as several oxide species (Ti2ZrO and ZrOx) during laser sintering process. Laser sintered Ti-ZrB2 cermets had high relative densities (> 92%) and hardness values (up to 11.4 GPa). The chemical reaction-enhanced dissolution of ZrB2 into Ti governed the final compositions of the cermets, which provides an opportunity to produce high-density boride solid solutions.

36 MATERIALS SCIENCE↗

Interfacial design and strengthening mechanisms of AZ91 alloy reinforced with in-situ reduced graphene oxide

Highlights: • An in-situ process was developed to synthesize magnesium alloy composite reinforced by graphene. • Microstructure and phase composition of oxide films were investigated by OM, SEM, EDS and XRD analysis. • The interfacial structure of Mg composites reinforced with reduced graphene oxide was characterized. • The interfacial reaction mechanisms between GO (graphene oxide) and the Mg metal was studied. - Abstract: This work highlights to develop an in-situ process to disperse uniformly graphene possessing good interfacial bonds with the matrix of Mg alloy. A homogeneous distribution of graphene in the matrix has been successfully obtained through in-situ reduction of graphene oxide (RGO) by sintering process after the graphene oxide (GO) was uniformly dispersed in AZ91 powders. The interface product nano-sized MgO can significantly improve the interfacial bonding strength between RGO and α-Mg with analysis by transmission electron microscopy. The orientation relationships of ( 2-bar 00){sub MgO}//( 1-bar 10 2-bar ){sub α‐Mg} and [011]{sub MgO}//[2 4-bar 2 3-bar ]{sub α‐Mg} with the semi-coherent interface characteristics were clarified for the first time at the interface of MgO/α-Mg, suggesting a good lattice space matching. By employing such process, a composite containing 0.5 wt% of GO shows an 85.7% and 61.4% increase in yield strength and elongation, respectively, over unreinforced AZ91 alloy. The underlying strengthening mechanisms of in-situ reduced graphene oxide are discussed in detail.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Sintering time and atmosphere influences on the microstructure and mechanical properties of tungsten heavy alloys

The present paper traces the microstructure and mechanical property variations vs sintering time under conditions where the atmosphere was adjusted to suppress pore generation. Attention is given to tracing the mechanical property links to the grain size under optimized sintering conditions. The optimal cycle is used to sinter two heavy alloy compositions (88 and 95 wt pct W) for times up to 600 minutes at 1480 C. The 88-pct-W samples slumped, but the 95-pct-W samples were fully densified and suitable for tensile testing. At long sintering times, the tungsten grains flattened and the tungsten contiguity decreased, indicating a transition to low-energy configurations for the solid-liquid interfaces. The cube of the mean grain size varied linearly with the isothermal sintering time. This allowed the determination of grain size effects on mechanical properties, showing a decreasing yield strength with increasing time in agreement with the Hall-Petch behavior. The tensile strength and elongation were highest for sintering times from 30 to 90 min, reflecting a minimum in the residual porosity.

German, R. M.↗

Abnormal Transient Liquid Phase Bondability of High-Volume Fraction SiC Particle-Reinforced A356 Composite for Cu Interlayer and the Interlayer Improvement Routes

Features of transient liquid phase (TLP) bondability of high-volume fraction (70 vol.%) SiC particle-reinforced A356 composite for popular Cu interlayer were investigated. Although Cu foil was melted, molten Cu was completely expulsed, indicating that the numerous SiC particles significantly deteriorated wettability not only at particle/braze metal (P/M) interface, but also at the matrix/braze metal (M/M) interface. For the reason of poor wettability at P/M interface, a model showing there is a “window period” for actual wetting reaction (allowing liquid phase to be in contact with surficial SiC particles) much shorter than nominal isothermal solidification time during TLP bonding of the composite containing sintered ceramic preform was proposed. For the poor wettability at M/M interface, both size effect of too small matrix unit (2 ~ 20 μm) and restraint effect of the rigid porous ceramic preform on suppressing oxide film crack on the small matrix unit surface were proposed. Thus, chemical route to disrupt oxide film on the small matrix unit surface should be preferred in braze composition design. For example, Al-27Cu-5Si-2Mg-1Ti braze was developed by co-addition of Mg and Ti to improve wettability and to in situ reinforce bond seam, respectively; Ti also could remedy Mg loss for improving wettability.

36 MATERIALS SCIENCE↗

Size-Dependent Adsorption and Adhesion Energetics of Ag Nanoparticles on Graphene Films on Ni(111) by Calorimetry

Interest in the use of carbon supports for late transition metal nanoparticle catalysts has expanded rapidly due to the increasing importance of electrocatalysts for clean energy and environmental technologies and the use and storage of renewable electricity. Compared to oxide supports, almost nothing is known about the effect of metal nanoparticle size on the energies of the metal atoms within carbon-supported nanoparticles, yet these energies are crucial for understanding their surface reactivity and sintering kinetics. Here, the growth morphology and adsorption energetics of vapor-deposited Ag onto clean graphene/Ni(111) surfaces have been studied using a combination of single-crystal adsorption calorimetry (SCAC) and He + low-energy ion scattering (LEIS). The differential heat of Ag adsorption is 207 kJ/mol for making ~30 atom Ag particles on graphene terraces at 100 K and 16 kJ/mol higher for making ~9 atom Ag clusters at defect sites at the same temperature. The heat of adsorption increases rapidly with Ag coverage as 3D Ag nanoparticles nucleate and grow in size, asymptotically reaching within 5 kJ/mol of the bulk Ag sublimation enthalpy (285 kJ/mol) by 2 ML. The heats of adsorption and Ag nanoparticle densities from LEIS (~10 16 /m 2 ) were combined to provide the Ag/graphene adhesion energy (E adh = 1.8 J/m 2 in the large-particle limit) and the Ag chemical potential (μ) versus effective particle diameter (D). The Ag chemical potential was well-fitted by μ(D) = (3γ v /M – E adh )(1 + (1.5 nm)/D)(2V m /D), where γ v /M is the surface energy of bulk Ag and V m is its molar volume. The same equation is known to fit similar data for late transition metals on clean surfaces of metal oxide single crystals. The adhesion energy of Ag measured here on graphene falls within the wide range measured for Ag on those oxide surfaces and is almost as large as on the oxide that binds Ag particles most strongly, namely CeO 2 (111), which is well-known to be very effective at resisting catalyst deactivation by metal sintering. Furthermore, these results imply that carbon supports will be effective at resisting sintering and that Ag particles smaller than 6 nm on graphene will bind small adsorbed reaction intermediates more weakly than supports with weaker adhesion to Ag, like MgO(100).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Ultrahigh temperature in situ transmission electron microscopy based bicrystal coble creep in Zirconia II: Interfacial thermodynamics and transport mechanisms

This work uses a combination of stress dependent single grain boundary Coble creep and zero-creep experiments to measure interfacial energies, along with grain boundary point defect formation and migration volumes in cubic ZrO 2 . These data, along with interfacial diffusivities measured in a companion paper are then applied to analyzing two-particle sintering. The analysis presented here indicates that the large activation volume, v * = v f + v m primarily derives from a large migration volume and suggests that the grain boundary rate limiting defects are delocalized, possibly due to electrostatic interactions between charge compensating defects. The discrete nature of the sintering and creep process observed in the small-scale experiments supports the hypothesis that grain boundary dislocations serve as sources and sinks for grain boundary point defects and facilitate strain during sintering and Coble creep. Model two-particle sintering experiments demonstrate that initial-stage densification follows interface reaction rate-limited kinetics.

36 MATERIALS SCIENCE↗

The mechanical properties measurement of multiwall carbon nanotube reinforced nanocrystalline aluminum matrix composite

Nanocrystalline aluminum matrix composite containing carbon nanotubes were fabricated using physical mixing method followed by cold pressing. The microstructure of the composite has been investigated using X-ray diffraction, scanning electron microscopy and energy dispersive spectroscopy techniques. These studies revealed that the carbon nanotubes were homogeneously dispersed throughout the metal matrix. The consolidated samples were pressureless sintered in inert atmosphere to further actuate a strong interface between carbon nanotubes and aluminum matrix. The nanoindentation tests carried out on considered samples showed that with the addition of 0.5 wt% carbon nanotubes, the hardness and elastic modulus of the aluminum matrix increased by 21.2 % and 2 % repectively. The scratch tests revealed a decrease in the friction coefficient of the carbon nanotubes reinforced composite due to the presence of lubricating interfacial layer. The prepared composites were promising entities to be used in the field of sporting goods, construction materials and automobile industries.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Surface Figure Measurement of Silicon Carbide Mirrors at Cryogenic Temperatures

The surface figure of a developmental silicon carbide mirror, cooled to 87 K and then 20 K within a cryostat, was measured with unusually high precision at the Goddard Space Flight Center (GSFC). The concave spherical mirror, with a radius of 600 mm and a clear aperture of 150 mm, was fabricated of sintered silicon carbide. The mirror was mounted to an interface plate representative of an optical bench, made of the material Cesic@, a composite of silicon, carbon, and silicon carbide. The change in optical surface figure as the mirror and interface plate cooled from room temperature to 20 K was 3.7 nm rms, with a standard uncertainty of 0.23 nm in the rms statistic. Both the cryo-change figure and the uncertainty are among the lowest such figures yet published. This report describes the facilities, experimental methods, and uncertainty analysis of the measurements.

Blake, Peter↗

Simultaneous Spark Plasma Sintering of Multiple Complex Shapes

This work addresses the two great challenges of the spark plasma sintering (SPS) process: The sintering of complex shapes and the simultaneous production of multiple parts. A new controllable interface method is employed to concurrently consolidate two nickel gear shapes by SPS. A graphite deformable sub-mold is specifically designed for the mutual densification of both complex parts in a unique 40 mm powder deformation space. An energy efficient SPS configuration is developed to allow the sintering of a large-scale powder assembly under electric current lower than 900 A. The stability of the developed process is studied by electro-thermal-mechanical (ETM) simulation. The ETM simulation reveals that homogeneous densification conditions can be attained by inserting an alumina powder at the sample/punches interfaces, enabling the energy efficient heating and the thermal confinement of the nickel powder. Finally, the feasibility of the fabrication of the two near net shape gears with a very homogeneous microstructure is demonstrated.

36 MATERIALS SCIENCE↗

Ultrasonic additive manufacturing of steel: Method, post-processing treatments and properties

In this study, ultrasonic additive manufacturing (UAM) was applied to fabricate laminated carbon steel structures. The feasibility of UAM to manufacture low-alloy carbon steel samples was proven. Interface investigation of the UAM parts was conducted by SEM, EBSD and TEM analysis. Multiple defects at the interfaces of the as-printed parts were observed. In order to improve the structural homogeneity and mechanical properties of the parts, spark plasma sintering (SPS) and hot isostatic pressing (HIP) post-treatments were applied. As a result, after both treatments, interface defects were healed and the shear strength of the welding interfaces was significantly improved. Lastly, treatment by SPS apparatus showed higher shear strength improvements as compared to the HIP-treated specimens.

36 MATERIALS SCIENCE↗

Performance and Reliability of Bonded Interfaces for High-Temperature Packaging. Annual Report

Current generation automotive power electronics packages utilize silicon devices and lead-free solder alloys. To meet stringent technical targets for 2020 and beyond (for cost, power density, specific power, efficiency and reliability), wide-bandgap devices are being considered since they offer advantages such as operation at higher frequencies, voltages, and temperatures. Traditional power electronics packages must be redesigned to utilize the full potential of wide-bandgap devices, and the die- and substrate-attach layers are key areas where new material development and validation is required. Present solder alloys do not meet the performance requirements for these new package designs while also meeting cost and hazardous substance restrictions. Sintered silver (Ag) promises to meet the needs for die- and substrate-attach interfaces but synthesis optimization and reliability evaluation must be completed. Sintered Ag material was proposed as an alternative solution in power electronics packages almost 20 years back. However, synthesis pressure requirements up 40 MPa caused a higher complexity in the production process and more stringent flatness specifications for the substrates. Recently, several manufacturers have developed sintered Ag materials that require lower (3-5 MPa) or even no bonding pressures. Degradation mechanisms for these sintered Ag materials are not well known and need to be addressed. We are addressing these aspects to some extent in this project. We are developing generalized (i.e., independent of geometry) stress intensity factor versus cycles-to-failure relations for sintered Ag. Because sintered Ag is a relatively new material for automotive power electronics, the industry currently does not have a good understanding of recommended synthesis parameters or expected reliability under prescribed conditions. It is an important deliverable of this project to transfer findings to industry to eliminate barriers to using sintered Ag as a viable and commercialized die- and substrate-attach material. Only a few manufacturers produce sintered Ag pastes and may consider some processing conditions as proprietary. It is the goal of this project to openly explore and define best practices in order to impact the maximum number of power electronics module manufacturers and suppliers.

30 DIRECT ENERGY CONVERSION↗