Search NASA⌕ Search

SEARCH · Search NASA

Results for “SOLIDIFICATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

In-Situ Synchrotron X-Ray Diffraction of Ultrasonic Microstructural Refinement During Solidification in a Commercial Al–Si–Mg Alloy

This study reports the first use of in-situ synchrotron X-ray diffraction (SXRD) to study the effects of ultrasonic melt processing (USMP) on phase and grain size evolution during solidification in a commercial Al–Si–Mg casting alloy. USMP is a technique that, when applied to aluminum as it solidifies, can be used to refine the local microstructure of large-scale castings. Analysis of the in-situ SXRD data to estimate the average grain size of primary α-Al grains during USMP demonstrates that USMP slows the growth rate of α-Al grains and reduces grain size by 36 pct. Furthermore, there is also evidence that USMP causes the primary α-Al grains to move relative to the X-ray beam; such motion increases the probability of primary α-Al grains colliding and fragmenting. This movement becomes constrained at the onset of the Al–Si binary eutectic, suggesting that USMP ceases to effectively refine the microstructure once the Al–Si binary eutectic begins to form. Complementary laboratory-scale X-ray diffraction (XRD) data were used to correlate the lattice parameters of the α-Al and Si (D-A4) phases with temperature to estimate cooling rate during solidification. Thus, this study can guide the design of novel castings with spatially distributed fine-grained regions produced using local ultrasonic processing.

Aluminum Alloys↗
DOE OSTI2020

Effects of Solidification Cooling Rates on Microstructures and Physical Properties of Fe-6.5%Si Alloys

Compared to the widely used Fe-3.2wt%Si steel, Fe-6.5wt%Si has superior electric and magnetic properties, including higher electrical resistivity, lower iron loss, higher permeability, and near zero magnetostriction. However, Fe-6.5wt%Si sheet is difficult to produce using traditional manufacturing processes as the high silicon content favors the formation of ordered phases that embrittle the material. Fortunately, these ordered phases can be suppressed if the alloy is cooled fast enough from a high temperature kinetically trapping the disordered solid solution or amorphous state. Planar flow casting is known for its rapid solidification rate. In order to consider it as a viable method to manufacture ductile Fe-6.5wt%Si sheets, the effect of cooling rate on physical properties of Fe-6.5wt%Si alloy are systematically investigated. In this work, various cooling rates are achieved by changing melt-spin wheel speeds, which significantly affect the solidification temperature profile and have profound effects on ordering, microstructures, textures, hardness, and magnetic properties. High cooling rates result in refined grains, reduced ordering, enhanced <100> out of the plane texture, decreased hardness, and increased coercivity. This study demonstrates a critical cooling rate at ~1.7 × 10 5 K/s, corresponding to a tangential wheel speed of 5-7 m/s, below which the hardness significantly increases in agreement with the sudden increase of the ordered phases that causes the material embrittlement.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Onset of magma ocean solidification on Mars inferred from Mn-Cr chronometry

The mantle of Mars probably differentiated through the crystallization of a magma ocean during the first tens of million years (Ma) of Solar System evolution. However, the exact timescale of large-scale silicate differentiation of the martian mantle is debated, and in particular, it remains unclear when differentiation commenced. In this paper, we applied the short-lived 53 Mn- 53 Cr system to martian meteorites in order to date the onset of large-scale mantle differentiation on Mars. The new Cr isotope data demonstrate that martian meteorites exhibit no resolvable radiogenic 53 Cr variations, and instead have a uniform +20.2±1.2 (95% conf.) parts-per-million excess in 53 Cr/ 52 Cr relative to the terrestrial mantle. The investigated groups of martian meteorites are lithologically varied and derive from diverse mantle sources that probably had variable Mn/Cr. Hence, the lack of 53 Cr variability among martian meteorites demonstrates that silicate differentiation on Mars occurred after the extinction of 53 Mn. Provided that the sources of the martian meteorites have Mn/Cr variations that are typical of the terrestrial planets, this result implies that the onset of large-scale silicate differentiation must have occurred later than 20±5 Ma after Solar System formation. The onset of silicate differentiation on Mars inferred here is significantly later than time estimates for segregation of the martian core which conservatively occurred within <10 Ma after Solar System formation. Thus, the new Mn-Cr data imply that there was a small, but resolvable, time gap of at least 5 Ma between core formation and magma ocean solidification on Mars. If the age of core segregation is taken at face value, our results imply that the martian magma ocean remained mostly molten over several Ma. This inferred longevity of the magma ocean is inconsistent with thermal models predicting rapid (<1 Ma) solidification of the martian magma ocean. Although there is currently no unique solution to this conundrum, our results can potentially be explained by a protracted history of impact bombardment that delayed differentiation in a shallow magma ocean on Mars, or perhaps more readily, by the presence of an early and dense atmosphere that acted as an insulator and prevented the magma ocean from cooling quickly.

58 GEOSCIENCES↗
DOE OSTI2020

Primary solidification of ternary compounds in Al-rich Al–Ce–Mn alloys

Primary solidification of ternary compounds Al 20 Mn 2 Ce and Al 10 Mn 2 Ce were analyzed through the coupling of the thermodynamic modeling and classic nucleation theory. Thermodynamic models of Al 20 Mn 2 Ce and Al 10 Mn 2 Ce were developed using the CALPHAD approach based on first-principles calculated enthalpy of formation and experimental data obtained from this work and the literature. The analysis suggested that despite the larger thermodynamic driving force for nucleation of Al 10 Mn 2 Ce, nucleation is preferred for the Al 20 Mn 2 Ce phase in the highly undercooled liquid due to its smaller interfacial energy. Therefore, manufacturing methods with rapid cooling rates will favor primary solidification of Al 20 Mn 2 Ce for Al-rich Al–Ce–Mn alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Solidification cracking of refractory alloys: a computational and machine learning study to investigate composition-dependence for improved weldability and additive manufacturability

Large-batch numerical, CALculation of PHAse Diagrams (CALPHAD)-based solidification cracking calculations are performed and then analyzed with machine learning methods to generate models that relate chemistry of refractory alloys to cracking susceptibility. Kou’s solidification cracking index is used to study the refractory alloys including O, N, C binary mixtures with Mo, Ta, Nb, and W, the molybdenum-based TZM, Niobium-based C103, and Tantalum-based T111 and Ta-10 W, as well as hypothetical refractory ternary alloys. Findings strongly validate Kou’s Crack Susceptibility Index (CSI) against Varestraint test data for Nb- and Ta-based alloys, establishing CSI thresholds where refractory alloys with CSI < 15,000 K are likely weldable, CSI > 15,000 K are prone to cracking, and CSI > 25,000 K are likely unweldable (or unprintable). Furthermore, interstitial elements C, N, and O significantly increase crack susceptibility, with some existing material specifications coinciding with peak cracking susceptibility concentrations. Finally, machine learning-derived elemental potency factors enable rapid prediction of CSI from alloy chemistry for C103, TZM, Ta-10 W, and T-111 alloys. These results provide practical guidance for feedstock selection, powder reuse limits, and alloy specification amendments for welding and additive manufacturing applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Irradiation of an enriched uranium (NaCl-UCl 3 ) fuel salt capsule, summary of nondestructive post-irradiation examinations, and solidification modeling

Molten salt reactors (MSRs) are gaining attention due to their potential for safe, carbon-free nuclear energy with reduced waste. However, licensing these reactors is hindered by limited experimental data on fueled salts, both pre- and post-irradiation. Here, the novel Molten-salt Research Temperature-controlled Irradiation (MRTI) vehicle was designed to address knowledge gaps in irradiating enriched‑uranium-bearing salts. The MRTI experiment irradiated 13 cm 3 of UCl₃-NaCl (93 % U-235) salt in the Neutron Radiography (NRAD) Reactor, achieving a burnup of 0.196 GWd/MTU over 390 h. Despite a heater failure, the thermocouple data suggested fission heat kept the salt molten. The MRTI assembly was remotely disassembled for nondestructive post-irradiation examination (PIE), which included precision gamma-ray scanning (PGS) and neutron radiography. Radiograph images showed the location of the salt and the solidification pattern. PGS results provided an early indication that activated materials of construction did not increase in relative intensity in the region of the capsule where the salt was in contact with the material of construction. Additionally, PGS data showed the presence of several gamma emitting fission products, such as Nb-95, Zr-95, Ru-103, Ce-141, and La-140, where Ru-103 had the highest counts at the bottom of the capsule. Computational fluid dynamics modeling supported observations of salt solidification patterns and proved to be a valuable tool to inform PIE activities. The MRTI experiment has thus far provided critical data and lessons learned for fuel salt PIE activities, essential for advancing the technical readiness of MSRs.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Quantification and prediction of solidification textures under additive manufacturing conditions

Crystallographic textures are a major determinant of the macroscale anisotropic properties of polycrystalline metallic alloys produced in a wide range of additive manufacturing (AM) processes. Here, we introduce a statistical method that can accurately quantify the degree of orientational order of textures despite the large random fluctuations in the orientation of individual grains inherent in AM processes. The method, demonstrated for laser and resolidification of AlSi thin films, extends Z-scoring to a dynamical regime to assess the statistical significance of observed textures compared to randomly generated ones at different stages of solidification. We further show that, combined with phase-field modeling, this method can be used to infer fundamental anisotropic properties of the solid-liquid interface that are essential for texture prediction, and are compared here to the results of atomistic simulations. In addition, phase-field modeling reveals that, even at rapid AM solidification rates, the observed 〈110〉-dominated textures in the AlSi thin films are controlled predominantly by the anisotropy of the interface free-energy and sheds light on the physical mechanism of grain competition. These results significantly enhance both the existing tools for the quantification and prediction of AM crystallographic textures and our basic understanding of their formation.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Highly Ordered Eutectic Mesostructures via Template‐Directed Solidification within Thermally Engineered Templates

Template-directed self-assembly of solidifying eutectics results in emergence of unique microstructures due to diffusion constraints and thermal gradients imposed by the template. Here, the importance of selecting the template material based on its conductivity to control heat transfer between the template and the solidifying eutectic, and thus the thermal gradients near the solidification front, is demonstrated. Simulations elucidate the relationship between the thermal properties of the eutectic and template and the resultant microstructure. The overarching finding is that templates with low thermal conductivities are generally advantageous for forming highly organized microstructures. When electrochemically porosified silicon pillars (thermal conductivity < 0.3 Wm −1 K −1 ) are used as the template into which an AgCl-KCl eutectic is solidified, 99% of the unit cells in the solidified structure exhibit the same pattern. In contrast, when higher thermal conductivity crystalline silicon pillars (≈100 Wm −1 K −1 ) are utilized, the expected pattern is only present in 50% of the unit cells. The thermally engineered template results in mesostructures with tunable optical properties and reflectances nearly identical to the simulated reflectances of perfect structures, indicating highly ordered patterns are formed over large areas. This work highlights the importance of controlling heat flows in template-directed self-assembly of eutectics.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Benchmark microgravity experiments and computations for 3D dendritic-array stability in directional solidification

In this study, we present a comprehensive quantitative analysis of stability bands for dendritic arrays during directional solidification of a transparent succinonitrile-0.46 wt % camphor alloy, spanning a broad range of pulling velocities. Taking advantage of the microgravity environment aboard the International Space Station where most convection effects are suppressed, we obtain unique measurements that quantify the stable primary spacing range of spatially extended three-dimensional dendritic array structures under purely diffusive growth conditions. Through carefully designed velocity jump experiments and detailed examination of sub-grain boundary dynamics, we characterize key instabilities, including elimination and tertiary branching, shedding new light on the mechanisms governing dynamic dendritic spacing selection in extended 3D arrays. Phase field simulations are performed to characterize the stability limits of dendritic array structures for quantitative comparison with the flight experiments. Although the simulations capture general trends, significant deviations are noted at the upper stability boundary, indicating the influence of additional, unexplored factors. These findings contribute to a deeper understanding of dendritic growth dynamics and offer valuable benchmark data that could aid in refining predictive models and improving control of dendritic microstructures in metallurgical applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Three-dimensional morphology of an ultrafine Al-Si eutectic produced via laser rapid solidification

Al-Si alloys processed by laser rapid solidification yield eutectic microstructures with ultrafine and interconnected fibers. Such fibrous structures have long been thought to bear resemblance to those formed in impurity-doped alloys upon conventional casting. Here, we show that any similarity is purely superficial. By harnessing high-throughput characterization and computer vision techniques, we perform a three-dimensional analysis of the branching behavior of the ultrafine eutectic and compare it against an impurity-modified eutectic as well as a random fractal (as a benchmark). Differences in the branching statistics point to different microstructural origins of the impurity- and quench-modified eutectic. Finally, our quantitative approach is not limited to the data presented here but can be used to extract abstract information from other volumetric datasets, without customization.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Coupling solidification kinetics with phase-behavior computations in hydrodynamic simulations of high-pressure, dynamic-compression processes

In this study, we report a numerical scheme to integrate models for the kinetics of solidification processes together with phase-behavior computations in the context of continuum-scale hydrodynamic simulations. The objective of the phase-behavior computations is to determine the pressure and temperature, given the following three sets of inputs: (1) an appropriate equation of state to describe our system, (2) the phase fraction(s) produced by the kinetic models, (3) and the volume and internal energy obtained by solving the conservation equations that govern the hydrodynamic behavior. The kinetics are assumed to be governed by the Kolmogorov–Johnson–Mehl–Avrami equation, and the nucleation and growth rates that enter into that equation are functions of the pressure and temperature produced by the phase-behavior computations. Our formulation allows for the fluid and solid phases to be at different temperatures (thermal nonequilibrium) and pressures (arising from surface-tension-induced Laplace contributions). The formulation is presented in a fairly general setting that is independent of any particular material, although we demonstrate it in some examples related to high-energy-density science applications where materials are rapidly compressed to pressures exceeding several gigapascals in less than a microsecond. We conclude with a critical evaluation of our approach and provide suggestions for future work to improve the predictive capabilities and generality of the models.

42 ENGINEERING↗
DOE OSTI2022

Multi-physics modeling of grain growth during solidification in electron beam additive manufacturing of Inconel 718

While experimental work has shown promising results regarding control of additive manufacturing metal grain structure, the effects of processing parameters on the grain structure is difficult to understand and predict from experiment alone. To this end, a modeling framework is developed which sequentially couples a macro-scale, semi-analytic thermal model, and a meso-scale, cellular automata-based microstructure model. This framework is applied to electron beam additive manufacturing of Inconel 718 using a complex spot scan pattern. The model shows that, with the same scan pattern, variations in the spot time and electron-beam current produce thermal histories with significant spatial and temporal differences, which then produce complex solidification conditions from the interplay between molten pools in the same layer and subsequent layers, resulting in vastly different grain structures. Additionally, it is noted that the framework can significantly reduce the computational expenses for coupled thermal-metallurgical problems, and has the potential to be used for component level problems.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Phase-field model of alloy solidification far from chemical equilibrium at the solid-liquid interface

We further develop a recently introduced phase-field model of far-from-equilibrium alloy solidification under additive manufacturing conditions [K. Ji et al., Phys. Rev. Lett. 130, 026203 (2023)]. This model utilizes enhanced solute diffusivity within the spatially diffuse interface region to quantitatively capture solute trapping with a larger interface width, thereby making simulations on experimentally relevant length and timescales computationally feasible. The main developments presented here include testing the robustness of different variational formulations, extending the model to concentrated alloys by incorporating solid and liquid free energies from thermodynamic databases, as illustrated for hypoeutectic Al-Ag alloys with CALPHAD, extending convergence tests as a function of interface width to 3D, and carrying out simulations in both 2D and 3D to examine existing theories of microstructure development. Our results indicate that the simplest variational formulation that interpolates the bulk free-energy density between its solid and liquid forms is the most robust. Remarkably, for hypoeutectic Al-Ag alloys, this formulation yields a high-velocity nonequilibrium phase diagram that is independent of interface width, thereby demonstrating that the framework of enhanced solute diffusivity can be nontrivially extended to concentrated alloys. Other variational formulations have restricted ranges of materials or processing parameters that can be reliably modeled. We use 2D simulations to construct high-velocity microstructure selection maps for dilute Al-Cu alloys. The results validate the important role of latent heat rejection at the interface and extend the limited predictions of linear stability analysis [A. Karma and A. Sarkissian, Phys. Rev. E 47, 513 (1993)] and sharp-interface 1D simulations to fully nonlinear regimes. Furthermore, 3D simulations, carried out using a computationally tractable axisymmetric cellular/dendritic interface shape, demonstrate a good convergence similar to that observed in 2D as a function of interface width. Full 3D simulations, in turn, reveal that the standard theory of absolute stability is a good predictor of the upper critical velocity beyond which steady-state growth becomes unstable, despite the different morphological manifestations of this instability in 2D and 3D.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Development of Magnesium Oxysulfate Formulation for SRPPF Aqueous Recovery Liquid Solidification

The liquid effluent from the Savannah River Plutonium Processing Facility (SRPPF) Aqueous Recovery Processes will be solidified into a stable form that is acceptable by Waste Isolation Pilot Plant (WIPP) for disposal. The current Aqueous Recovery flow sheet proposes to solidify the liquid effluent using a grout formula that was developed and tested for the former Waste Solidification Building process. This Portland cement based mixture results in a high pH (~13) leachate from the solidified waste form which is not acceptable to WIPP in the large quantities expected from production at SRPPF. Various cementitious materials were previously evaluated as alternative grout formulations to Portland cement and a MgO-based mix was identified as a promising alternative. A magnesium oxysulfate (MOS) cement formulation comprised of reactive magnesium oxide (MgO), anhydrous magnesium sulfate (MgSO 4 ), and sand, as a non-reactive heat sink provided good mixability, similar density to the original Portland-cement based mix, and a leachate pH of 9.4, within the assumed WIPP brine pH range. However, the MOS formulation exhibited an appreciable amount of heat generation, which resulted in premature setting of a large-scale test.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Effects of SRPPF ARS Effluent Variations on Magnesium Oxysulfate Solidification

A magnesium oxysulfate (MOS) grout formulation has been identified to solidify the liquid effluent from the Savannah River Plutonium Processing Facility (SRPPF) Aqueous Recovery System (ARS). The formulation uses reactive, light burnt MgO (28 wt%), anhydrous MgSO 4 (10 wt%), and dead burnt MgO (62 wt%), resulting in a grout with good mixability, acceptable density, acceptable setting times, and a leachate pH around 9.4, within the assumed Waste Isolation Pilot Plant (WIPP) brine pH range. A series of tests were then designed to observe how this formula reacted to variations in the liquid effluent. Liquid effluent temperature, the caustic pH level, concentration of NaNO 3 , and the presence of neutralization products, trace metals, and/or sodium sulfate (all potential residuals found in the effluent from upstream processing), were evaluated to see how each impacts the grout mixing time, peak temperature, setting time, presence of bleed water, leachate pH, and density. The standard mix has an average mixing time of 18 minutes, peak temperature of 100.5 °C, and set time of 60 minutes. Increasing the temperature of the liquid effluent increased the reaction rate of the mix and reduced mixing and setting times. Between 30 and 40°C the change was relatively small, raising no more than 6 °C compared to the standard mix maximum temperature. Increasing the pH of the liquid effluent had no significant impact on the mix. The addition of neutralization products and trace metals had an overall impact of decreasing the reactivity of the mix. The addition of more ions in the liquid effluent, such as an increase in the concentration of NaNO 3 and the addition of Na 2 SO 4 , generally decreased the reactivity of the mix. None of the variations to the liquid effluent hindered solidification as indicated by the lack of bleed water found on all the samples. The leachate pH values for all mixes tested did not significantly vary from the expected pH of 9.4 and none of the density values fell below 1.8 g/cm 3 . Overall, changes to the liquid effluent were found to have a minimal impact on the formulation suggesting the grout's ability to properly form despite increased temperatures and the presence of residuals typically found in the liquid effluent from the ARS.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Quantifying Equiaxed vs Epitaxial Solidification in Laser Melting of CMSX-4 Single Crystal Superalloy

The competition between epitaxial vs. equiaxed solidification has been investigated in CMSX-4 single crystal superalloy during laser melting as practiced in additive manufacturing. Single-track laser scans were performed on a powder-free surface of directionally solidified CMSX-4 alloy with several combinations of laser power and scanning velocity. Electron backscattered diffraction (EBSD) mapping facilitated identification of new orientations, i.e., “stray grains” that nucleated within the fusion zone along with their area fraction and spatial distribution. Using high-fidelity computational fluid dynamics simulations, both the temperature and fluid velocity fields within the melt pool were estimated. This information was combined with a nucleation model to determine locations where nucleation has the highest probability to occur in melt pools. In conformance with general experience in metals additive manufacturing, the as-solidified microstructure of the laser-melted tracks is dominated by epitaxial grain growth; nevertheless, stray grains were evident in elongated melt pools. It was found that, though a higher laser scanning velocity and lower power are generally helpful in the reduction of stray grains, the combination of a stable keyhole and minimal fluid velocity further mitigates stray grains in laser single tracks.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Melting and solidification dynamics during laser melting of reaction-based metal matrix composites uncovered by in-situ synchrotron X-ray diffraction

Laser additive manufacturing (AM) of reaction-based metal matrix composites (MMCs) involves highly complex and non-equilibrium material transformation behavior, including melting, dissolution, precipitation, and solidification. Yet, the dynamics and interplay of these phase transformation processes remain poorly understood, posing substantial challenges in identifying the microstructure formation mechanism, and predicting and controlling the microstructure in the printed parts. Here, in this study, we performed the in-situ X-ray diffraction experiment to characterize the phase evolution dynamics of the 316L + 10 vol.%TiC system during laser melting, which provides direct and quantitative insights of the complex phase reaction and evolution dynamics under rapid heating and cooling conditions relevant to additive manufacturing of reaction-based MMCs. Further in-depth thermodynamic and kinetic calculations revealed that most of the phase evolution behavior observed in the in-situ X-ray diffraction experiment cannot be solely explained by widely used equilibrium thermodynamic models, and diffusion-controlled nonequilibrium dissolution and precipitation kinetics must be considered to elucidate the complex phase evolution behavior, including incomplete TiC dissolution, and three-step TiC precipitation. The three distinct types of precipitates generate unique hierarchical TiC micro- and nanostructures, which enhances the yield strength from 513 MPa to 877 MPa by 71 %, tensile strength from 628 MPa to 1054 MPa by 68 %, and Young's modulus from 193 GPa to 221 GPa by 14 %. The findings of our research provide the knowledge foundation for the design of unique microstructures and advanced MMC materials through laser AM.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Solidification texture, variant selection, and phase fraction in a spot-melt electron-beam powder bed fusion processed Ti-6Al-4V

The effect of a spot melt strategy on the solidification texture, variant selection, phase fraction, and their variations along the build height was investigated in comparison to a conventional linear melt strategy. Ti-6Al-4V alloy samples were manufactured by an electron-beam powder bed fusion process using two different melt strategies and characterized using high-energy synchrotron x-ray diffraction. The linear and spot melt cases resulted in β<100> cube and fiber textures, respectively, with the cube/fiber axis nearly parallel to the build direction. The α phase exhibited Burgers orientation relationship (BOR) with the parent β phase for both melt strategies. Although all of the key texture components and the BOR between the α and β phases were consistently observed in both cases along the build height, there were several measurable differences between the two. At the top of the build height, the β<100> build texture intensity was stronger in the linear case. However, the texture intensity in the linear case decreased gradually from the top to near the substrate, whereas the spot melt case did not show this trend. Moreover, the BOR was examined along the build height and the results showed that there is a distinct variant selection in the spot melt case, unlike the linear case. Specifically, the planar variants sharing ($\bar101$) β || (0002) α with [$\bar2\bar2\bar2$]β and [$2\bar22$]β were the most prominent in the spot melt, but no preference was identified in the directional variants. The β phase fraction was slightly lower in the spot melt case compared to the linear case. In both the cases, the β phase fraction decreased moving towards the substrate but remained significantly higher than that of the powder feedstock. Overall, the novel spot melt strategy produced a more homogeneous microstructure in terms of both the phase fraction and texture across the build height.

36 MATERIALS SCIENCE↗