Results for “STABILITY CALCULATIONS” — Page 4

NASA NTRS1943

The Effect of Mass Distribution on the Lateral Stability and Control Characteristics of an Airplane as Determined by Tests of a Model in the Free-flight Tunnel

The effects of mass distribution on lateral stability and control characteristics of an airplane have been determined by flight tests of a model in the NACA free-flight tunnel. In the investigation, the rolling and yawing moments of inertia were increased from normal values to values up to five times normal. For each moment-of-inertia condition, combinations of dihedral and vertical-tail area representing a variety of airplane configurations were tested. The results of the flight tests of the model were correlated with calculated stability and control characteristics and, in general, good agreement was obtained.

Campbell, John P↗

NASA NTRS1943

The Effect of Mass Distribution on the Lateral Stability and Control Characteristics of an Airplane as Determined by Tests of a Model in the Free-Flight Tunnel

The effects of mass distribution on lateral stability and control characteristics of an airplane have been determined by flight tests of a model in the NACA free-flight tunnel. In the investigation, the rolling and yawing movements of inertia were increased from normal values to values up to five times normal. For each moment-of-inertia condition, combinations of dihedral and vertical-tail area representing a variety of airplane configurations were tested. The results of the flight tests of the model were correlated with calculated stability and control characteristics and, in general, good agreement was obtained. The tests showed the following effects of increased rolling and yawing moments of inertia: no appreciable change in spiral stability; reductions in oscillatory stability that were serious at high values of dihedral; a reduction in the sensitivity of the model to gust disturbances; and a reduction in rolling acceleration provided by the ailerons, which caused a marked increase in time to reach a given angle of bank. The general flight behavior of the model became worse with increasing moments of inertia but, with combinations of small effective dihedral and large vertical-tail area, satisfactory flight characteristics were obtained at all moment-of-inertia conditions.

STABILITY & CONTROL, LATERAL↗

NASA NTRS2020

Streak Instabilities on HIFiRE-5 Elliptic Cone

The Hypersonic International Flight Research and Experimentation (HIFiRE) 5 flight experiment by the Air Force Research Laboratories and Australian Defense Science and Technology Organization yielded inflight, hypersonic transition data for a canonical, 3D configuration in the form of an elliptic cone at various combinations of angle-of-attack and yaw. Previous analysis has shown that boundary-layer stability calculations for the as-flown, zero-yaw flight conditions are able to capture the second mode dominated transition along the attachment line as well as the crossflow induced transition in between the attachment line and the minor axis symmetry plane. However, there is still a need to understand the transition in the vicinity of the minor axis plane of symmetry, where the boundary layer thickness exhibits an azimuthally compact bulge due to the collision of the secondary flow approaching from the attachment lines on both sides. This paper reports a computational analysis of the stability of the boundary layer flow along the bulge regions on both the leeward and windward sides of the vehicle surface. At a representative flight condition corresponding to a time instant of t = 514.813 seconds, computations are performed to identify several different unstable modes within the bulge regions, with the eventual goal of developing a linear stability correlation for the transition onset near the minor axis symmetry plane. The most amplified flow instabilities in the pretransitional region correspond to a “stem” mode that is concentrated within a pair of nearly vertical shear layers below the cap of the mushroom shaped bulge in the mean velocity contours. An excellent agreement is found between the predictions of instability amplification based on the plane marching parabolized stability equations (PSE) and the direct numerical solutions (DNS). Given the large number of unstable modes within the bulge region, the observed agreement demonstrates, for first time, that the PSE can provide accurate predictions for the development of flow instabilities in streak-like flow features over three-dimensional bodies. The peak N-factor of approximately 15 at the transition location estimated from the thermocouple measurements along the leeward centerline is close to the transition N-factor for Mack mode transition during the HIFiRE-1 circular cone flight experiment with nearly zero degrees angle of attack.

Meelan Choudhari↗

NASA NTRSDate not supplied

Enhancements to Linear Stability-Based, CFD-integrated Transition Prediction for High-Speed Flows

Combining linear stability calculations with computational fluid dynamics (CFD) simulations has great potential for the automated modeling of high-speed flows, especially when adequate information about the configuration and the disturbance environment is available. However, a significant impediment to the applicability of this technique is the lack of an efficient method to calculate the crucial amplification ratio corresponding to the onset of transition in hypersonic flows. This ratio, also known as the "transition N-factor," is dependent upon the freestream disturbance environment as well as the surface properties of the test article. In response to the need for an engineering solution to predict the transition N-factor within conventional hypersonic wind tunnels, this paper presents a data-driven correlation that expands the existing correlations from straight circular cones with a narrow range of half angles to a broader array of axisymmetric configurations. Furthermore, when tested against a chosen dataset that was not used in its calibration, the suggested correlation shows good predictive accuracy with an RMS error of only 6.9%. Although similar accuracy may also be achieved via existing correlations based on similar datasets, predictions based on the proposed correlation have the advantage of not requiring an extensive amount of configuration-specific data. Practical applications often have access to the input parameters needed for this correlation, such as the freestream disturbance intensity, Mach number, and body-based slenderness Reynolds number. Additionally, this correlation outperforms the traditional assumption of a constant N-factor, particularly for configurations with blunted nose geometries. The development of this correlation is grounded in an extensive dataset encompassing conical models with body half-angles varying between 5 degrees and 16 degrees, Mach numbers ranging from 5 to 14, and nosetip-based Reynolds numbers approaching the transition reversal limit for blunt-nosed cones.

CFD↗

NASA NTRSDate not supplied

Enhancements to Linear Stability-Based, CFD-integrated Transition Prediction for High-Speed Flows

Combining linear stability calculations with computational fluid dynamics (CFD) simulations has great potential for the automated modeling of high-speed flows, especially when adequate information about the configuration and the disturbance environment is available. However, a significant impediment to the applicability of this technique is the lack of an efficient method to calculate the crucial amplification ratio corresponding to the onset of transition in hypersonic flows. This ratio, also known as the "transition N-factor," is dependent upon the freestream disturbance environment as well as the surface properties of the test article. In response to the need for an engineering solution to predict the transition N-factor within conventional hypersonic wind tunnels, this paper presents a data-driven correlation that expands the existing correlations from straight circular cones with a narrow range of half angles to a broader array of axisymmetric configurations. Furthermore, when tested against a chosen dataset that was not used in its calibration, the suggested correlation shows good predictive accuracy with an RMS error of only 6.9%. Although similar accuracy may also be achieved via existing correlations based on similar datasets, predictions based on the proposed correlation have the advantage of not requiring an extensive amount of configuration-specific data. Practical applications often have access to the input parameters needed for this correlation, such as the freestream disturbance intensity, Mach number, and body-based slenderness Reynolds number. Additionally, this correlation outperforms the traditional assumption of a constant N-factor, particularly for configurations with blunted nose geometries. The development of this correlation is grounded in an extensive dataset encompassing conical models with body half-angles varying between 5 degrees and 16 degrees, Mach numbers ranging from 5 to 14, and nosetip-based Reynolds numbers approaching the transition reversal limit for blunt-nosed cones.

CFD↗

NASA NTRS1969

Radical stabilities in nitrogen containing heterocyclic systems

Spin stability calculations of radicals in nitrogen containing heterocyclic compounds

Evleth, E. M.↗

NASA NTRS1974

Free-flight investigation of the stability and control characteristics of a STOL model with an externally blown jet flap

The stability and control characteristics of a four-engine turbofan STOL transport model having an externally blown jet flap have been investigated by means of the flying-model technique in the Langley full-scale tunnel. The flight characteristics of the model were investigated under conditions of symmetric and asymmetric (one engine inoperative) thrust at lift coefficients up to 9.5 and 5.5, respectively. Static characteristics were studied by conventional power-on force tests over the flight-test angle-of-attack range including the stall. In addition to these tests, dynamic longitudinal and lateral stability calculations were performed for comparison with the flight-test results and for use in correlating the model results with STOL handling-qualities criteria.

Parlett, L. P.↗

NASA NTRS1974

Design of a Torque Current Generator for Strapdown Gyroscopes

The design, analysis, and experimental evaluation of an optimum performance torque current generator for use with strapdown gyroscopes, is presented. Among the criteria used to evaluate the design were the following: (1) steady-state accuracy; (2) margins of stability against self-oscillation; (3) temperature variations; (4) aging; (5) static errors drift errors, and transient errors, (6) classical frequency and time domain characteristics; and (7) the equivalent noise at the input of the comparater operational amplifier. The DC feedback loop of the torque current generator was approximated as a second-order system. Stability calculations for gain margins are discussed. Circuit diagrams are shown and block diagrams showing the implementation of the torque current generator are discussed.

Mcknight, R. D.↗

NASA NTRS1975

Experimental investigation of reaction coronas on olivine in Apollo 14 high-grade breccias

Reaction coronas of pyroxene plus or minus ilmenite occur around clasts of olivine in Apollo 14 high-grade metamorphic breccias. In experiments of several months duration, there was no evidence of corona formation at 1000 C, but at 1050, with oxygen fugacity at or above Ilm-Ru-Fe and below Fe-Fe(1-x)O, incipient coronas formed around Fo(50-70), Fo(68), En(69) + Fe. Reduction of olivine under these conditions is inconsistent with the calculated stability relations and is attributed to uncertainties in the activity coefficient for olivine or pyroxene. The experiments also suggest that vesicularity in the Apollo 14 high-grade breccias may correlate with the amount of glassy material in their unmetamorphosed precursors. The metamorphic event is attributed to burial in a hot ejecta blanket, such as that of the Imbrium event.

Kesson, S. E.↗

NASA NTRS1977

Solar oscillations

The main observational results and related theoretical investigations concerning solar oscillations are reviewed. The normal modes of oscillation of the sun are classified according to their angular eigenvalues and the number of their radial nodes. Observations of excited normal modes are discussed, particularly in relation to five-minute oscillations, nonlinearly coupled unstable g-modes, oscillations of the sun's apparent diameter, and reported oscillations of the solar surface with a period of 2 hr 40 min. Linear stability calculations are briefly examined, and stochastic excitation of p-modes by turbulent convection is considered. The five-minute oscillations are described as the superposition of many excited nonradial p-modes.

Goldreich, P.↗

NASA NTRS1980

Flow Induced Spring Coefficients of Labyrinth Seals for Application in Rotor Dynamics

Flow induced aerodynamic spring coefficients of labyrinth seals are discussed and the restoring force in the deflection plane of the rotor and the lateral force acting perpendicularly to it are also considered. The effects of operational conditions on the spring characteristics of these components are examined, such as differential pressure, speed, inlet flow conditions, and the geometry of the labyrinth seals. Estimation formulas for the lateral forces due to shaft rotation and inlet swirl, which are developed through experiments, are presented. The utilization of the investigations is explained and results of stability calculations, especially for high pressure centrifugal compressors, are added. Suggestions are made concerning the avoidance of exciting forces in labyrinths.

Benckert, H.↗

NASA NTRS1980

Flow over plates with suction through porous strips

This paper addresses the steady, incompressible, two-dimensional flow past a flat plate with suction through porous strips. Closed-form solutions for each flow quantity are developed in the context of linearized triple-deck theory using Fourier transforms. To demonstrate the validity of these closed-form solutions, we compare the wall shear stress and pressure coefficients and the streamwise velocity profiles from the linearized theory with those obtained by the numerical integration of both interacting and nonsimilar boundary-layer equations. The agreement between the linearized triple-deck and interacting boundary-layer equations is good; however, the nonsimilar boundary layers, which fail to account for upstream influence, are shown to be in poor agreement with both interacting boundary layers and the linearized triple deck. The linearized closed-form solutions will therefore be very useful in future stability calculations.

Nayfeh, A. H.↗

NASA NTRS1981

Efficient computation of the stability of three-dimensional compressible boundary layers

Methods for the computer analysis of the stability of three-dimensional compressible boundary layers are discussed and the user-oriented Compressible Stability Analysis (COSAL) computer code is described. The COSAL code uses a matrix finite-difference method for local eigenvalue solution when a good guess for the eigenvalue is available and is significantly more computationally efficient than the commonly used initial-value approach. The local eigenvalue search procedure also results in eigenfunctions and, at little extra work, group velocities. A globally convergent eigenvalue procedure is also developed which may be used when no guess for the eigenvalue is available. The global problem is formulated in such a way that no unstable spurious modes appear so that the method is suitable for use in a black-box stability code. Sample stability calculations are presented for the boundary layer profiles of an LFC swept wing.

Malik, M. R.↗

NASA NTRS1982

Finite-difference solution of the compressible stability eigenvalue problem

A compressible stability analysis computer code is developed. The code uses a matrix finite difference method for local eigenvalue solution when a good guess for the eigenvalue is available and is significantly more computationally efficient than the commonly used initial value approach. The local eigenvalue search procedure also results in eigenfunctions and, at little extra work, group velocities. A globally convergent eigenvalue procedure is also developed which may be used when no guess for the eigenvalue is available. The global problem is formulated in such a way that no unstable spurious modes appear so that the method is suitable for use in a black box stability code. Sample stability calculations are presented for the boundary layer profiles of a Laminar Flow Control (LFC) swept wing.

Malik, M. R.↗

NASA NTRS1983

The inner edge of Saturn's B ring

The sharp, 90-km wide transition from an optical depth of 0.2 in the C ring to 1 in the B ring begins at 91,970 km from Saturn's center. This radius is found to be almost exactly at the inward stability limit of charged particles launched in the ring plane at the local Kepler velocity, provided these particles have large charge to mass ratio. The zonal harmonic models of Saturn's magnetic field from the Voyager data and the gravitational field model from Pioneer data are essential to get the very close agreement between theory and observation. The theoretical stability limits are 91,973 + or - 145 km from Voyager 1 magnetic field data and 91,991 + or 145 km from Voyager 2 magnetic data. The zonal harmonic magnetic field lines are not perpendicular to the ring plane. Therefore, in addition to the magnetic mirror, gravitational, and centrifugal forces, an unknown force must be postulated to produce equilibrium in the ring plane and make the stability calculation meaningful.

Northrop, T. G.↗

NASA NTRS1985

Experiments on the stability of crossflow vortices in swept-wing flows

Experiments are conducted which demonstrate the feasibility of creating crossflow vortices in a flat-plate flow. A swept leading edge and contoured wind-tunnel walls produce a strong pressure gradient and a typical swept-wing flow on the plate. Detailed three-dimensional measurements, made within the boundary layer using hot-wire anemometry, are supplemented with different flow-visualization techniques. Data are presented on the mean flow characteristics as well as on the behavior of the crossflow vortices. Comparisons are made with theoretical flow-field and stability calculations.

Saric, W. S.↗

NASA NTRS1986

Applications of potential theory computations to transonic aeroelasticity

Unsteady aerodynamic and aeroelastic stability calculations based upon transonic small disturbance (TSD) potential theory are presented. Results from the two-dimensional XTRAN2L code and the three-dimensional XTRAN3S code are compared with experiment to demonstrate the ability of TSD codes to treat transonic effects. The necessity of nonisentropic corrections to transonic potential theory is demonstrated. Dynamic computational effects resulting from the choice of grid and boundary conditions are illustrated. Unsteady airloads for a number of parameter variations including airfoil shape and thickness, Mach number, frequency, and amplitude are given. Finally, samples of transonic aeroelastic calculations are given. A key observation is the extent to which unsteady transonic airloads calculated by inviscid potential theory may be treated in a locally linear manner.

Edwards, J. W.↗

NASA NTRS1987

Some observations of a sheared Rayleigh-Taylor/Benard instability

An account is provided of preliminary flow visualization observations made in an unstably stratified flow with shear superimposed. The structures observed appear to be the superposition of a Rayleigh-Taylor/Benard instability and a Kelvin-Helmholtz instability. Aside from its intrinsic fundamental value, the study of these structures is of special interest to theoreticians developing nonlinear stability calculation methodologies.

Humphrey, J. A. C.↗