Search NASA⌕ Search

SEARCH · Search NASA

Results for “STAGNATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Stagnation Temperature Recording

The present report deals with the development of a thermometer for recording stagnation temperature in compressible mediums in turbulent flow within 1 to 2 percent error of the adiabatic temperature in the stagnation point, depending upon the speed. This was achieved by placing the junction of a thermocouple near the stagnation point of an aerodynamically beneficial body, special care being taken to assure an uninterrupted supply of fresh compressed air on the junction together with the use of metals of low thermal conductivity, thus keeping heat-transfer and heat-dissipation losses to a minimum. In other experiments the use of the plate thermometer was proved unsuitable for practical measurements by reason of its profound influence in the reading by the Reynolds number and by the direction of flow.

Wimmer, W↗

Experimental Determination of the Recovery Factor and Analytical Solution of the Conical Flow Field for a 20 deg Included Angle Cone at Mach Numbers of 4.6 and 6.0 and Stagnation Temperatures to 2600 degree R

The local recovery factor was determined experimentally along the surface of a thin-walled 20 deg included angle cone for Mach numbers near 6.0 at stagnation temperatures between 1200 deg R and 2600 deg R. In addition, a similar cone configuration was tested at Mach numbers near 4.5 at stagnation temperatures of approximately 612 deg R. The local Reynolds number based on flow properties at the edge of the boundary layer ranged between 0.1 x 10(exp 4) and 3.5 x 10(exp 4) for tests at temperatures above 1200 deg R and between 6 x 10(exp 4) and 25 x 10(exp 4) for tests at temperatures near 612 deg R. The results indicated, generally, that the recovery factor can be predicted satisfactorily using the square root of the Prandtl number. No conclusion could be made as to the necessity of evaluating the Prandtl number at a reference temperature given by an empirical equation, as opposed to evaluating the Prandtl number at the wall temperature or static temperature of the gas at the cone surface. For the tests at temperatures above 1200 deg R (indicated herein as the tests conducted in the slip-flow region), two definite trends in the recovery data were observed - one of increasing recovery factor with decreasing stagnation pressure, which was associated with slip-flow effects and one of decreasing recovery factor with increasing temperature. The true cause of the latter trend could not be ascertained, but it was shown that this trend was not appreciably altered by the sources of error of the magnitude considered herein. The real-gas equations of state were used to determine accurately the local stream properties at the outer edge of the boundary layer of the cone. Included in the report, therefore, is a general solution for the conical flow of a real gas using the Beattie-Bridgeman equation of state. The largest effect of temperature was seen to be in the terms which were dependent upon the internal energy of the gas. The pressure and hence the pressure drag terms were unaffected.

Pfyl, Frank A.↗

Ballistic Range Measurements of Stagnation-Point Heat Transfer in Air and in Carbon Dioxide at Velocities up to 18,000 Feet Per Second

A new technique for measuring heat-transfer rates on free-flight models in a ballistic range is described in this report. The accuracy of the heat-transfer rates measured in this way is shown to be comparable with the accuracy obtained in shock-tube measurements. The specific results of the present experiments consist of measurements of the stagnation-point heat-transfer rates experienced by a spherical-nosed model during flight through air and through carbon dioxide at velocities up to 18,000 feet per second. For flight through air these measured heat-transfer rates agree well with both the theoretically predicted rates and the rates measured in shock tubes. the heat-transfer rates agree well with the rates measured in a shock tube. Two methods of estimating the stagnation-point heat-transfer rates in carbon dioxide are compared with the experimental measurements. At each velocity the measured stagnation-point heat-transfer rate in carbon dioxide is about the same as the measured heat-transfer rate in air.

Yee, Layton↗

Stagnation Point Heat Transfer with Gas Injection Cooling

The present paper deals with an experimental study of the stagnation-point heat transfer to a cooled copper surface with gas injection under subsonic conditions. Test were made with a probe that combined a steady-state water-cooled calorimeter that allows the capability to study convective blockage and to perform heat transfer measurements in presence of gas injection in the stagnation region. The copper probe was pierced by 52 holes, representing 2.4% of the total probe surface. The 1.2 MW high enthalpy plasma wind tunnel was operated at anode powers between 130 and 230 kW and a static pressures from 35 hPa up to 200 hPa. Air, carbon dioxide and argon were injected in the mass flow range 0-0.4 g/s in the boundary layer developed around the 50 mm diameter probe. The measured stagnation-point heat transfer rates are reported and discussed.

Vancrayenest, B.↗

Stagnation Point Radiative Heating Relations for Venus Entry

Improved analytic expressions for calculating the stagnation point radiative heating during entry into the atmosphere of Venus have been developed. These analytic expressions can be incorporated into entry trajectory simulation codes. Together with analytical expressions for convective heating at the stagnation point, the time-integrated total heat load at the stagnation point is used in determining the thickness of protective material required, and hence the mass of the fore body heatshield of uniform thickness.

Tauber, Michael E.↗

Investigation of Hypersonic Laminar Heating Augmentation in the Stagnation Region

Laminar stagnation region heating augmentation is investigated in the AEDC Tunnel 9 at Mach 10 by performing high frequency surface pressure and heat transfer measurements on the Orion CEV capsule at zero degree angle-of-attack for unit Reynolds numbers between 0.5 and 15 million per foot. Heating augmentation increases with Reynolds number, but is also model size dependent as it is absent on a 1.25-inch diameter model at Reynolds numbers where it reaches up to 15% on a 7-inch model. Heat transfer space-time correlations on the 7-inch model show that disturbances convect at the boundary layer edge velocity and that the streamwise integral scale increases with distance. Therefore, vorticity amplification due to stretching and piling-up in the stagnation region appears to be responsible for the stagnation point heating augmentation on the larger model. This assumption is reinforced by the f(exp -11/3) dependence of the surface pressure spectrum compared to the f(exp -1) dependence in the free stream. Vorticity amplification does not occur on the 1.25- inch model because the disturbances are too large. Improved free stream fluctuation measurements will be required to determine if significant vorticity is present upstream or mostly generated behind the bow shock.

Marineau, Eric C.↗

Convective Enhancement of Icing Roughness Elements in Stagnation Region Flows

To improve existing ice accretion simulation codes, more data regarding ice roughness and its effects on convective heat transfer are required. To build on existing research on this topic, this study used the Vertical Icing Studies Tunnel (VIST) at NASA Glenn Research to model realistic ice roughness in the stagnation region of a NACA 0012 airfoil. Using the VIST, a test plate representing the leading 2% chord of the airfoil was subjected to flows of 7.62 m/s (25 ft/s), 12.19 m/s (40 ft/s), and 16.76 m/s (55 ft/s). The test plate was fitted with 3 surfaces, each with a different representation of ice roughness: 1) a control surface with no ice roughness, 2) a surface with ice roughness with element height scaled by 10x and streamwise rough zone width from the stagnation point scaled by 10x, and 3) a surface with ice roughness with element height scaled by 10x and streamwise rough zone width from the stagnation point scaled by 25x. Temperature data from the tests were recorded using an infrared camera and thermocouples imbedded in the test plate. From the temperature data, a convective heat transfer coefficient map was created for each case. Additional testing was also performed to validate the VIST's flow quality. These tests included five-hole probe and hot-wire probe velocity traces to provide flow visualization and to study boundary layer formation on the various test surfaces. The knowledge gained during the experiments will help improve ice accretion codes by providing heat transfer coefficient validation data and by providing flow visualization data helping understand current and future experiments performed in the VIST.

Icing↗

Ignition of n-heptane pool by heated stagnating oxidizing flow

The ignition temperature of a liquid pool of n-heptane by heated oxidizer in a stagnation flow was experimentally determined for system pressures of 0.61-3 atm and pressure-weighted strain rates of 60-350 s{sup -1}. The surface of the liquid pool was maintained at a fixed location through continuous replenishment. The state of ignition was brought about, and monitored, by gradually increasing the oxidizer temperature. The strain rate was determined by seeding and measuring the oxidizer flow velocity using laser Doppler velocimetry (LDV). Computational simulation of the ignition event with detailed chemistry and transport was conducted by using a stagnation-flow code. The kinetic mechanisms utilized are a high-temperature n-heptane oxidation model, with 130 species and 955 reactions, and a reduced one of 58 species derived from a detailed mechanism of 561 species and 2539 reactions. The former mechanism yielded better agreement with the experimental measurements in general over the conditions examined. It was also found that the mole fraction of n-heptane at the interface changed only slightly with pressure and strain rate, and can be considered to have minimal effect on the ignition responses studies herein. A recently developed explosive mode analysis (EMA) was conducted to identify the controlling radicals and reactions in the non-premixed ignition of n-heptane. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Laser scattered images observed from carbon plasma stagnation and following molecular formation

Two carbon targets were irradiated to create plasma plumes to collide at right angle with two UV laser pulses each other at 10 J/cm{sup 2}/pulse. The collision results in carbon plasma stagnation. Laser scattered imaging indicates that the carbon large molecular formation takes place much later in time after the laser irradiation and stagnation. Compared with the temporal history of electron density (n{sub e}), ion density (n{sub i}), and plasma self-emission dominated by carbon Swan band, it is estimated that the carbon large molecular formation has been initiated with the ion collision followed by the C{sub 2} formation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Propagation of microwave beams through the stagnation zone in an inhomogeneous plasma

A study is made of the microwave beam evolution due to passing through the stagnation zone, where the group velocity vanishes, thus making the paraxial approximation for the wavefield inappropriate. An extension to the standard beam tracing technique is suggested that allows one to calculate the microwave beam parameters on either branch of its path apart from the stagnation zone, omitting the calculation of the wavefield inside it. Application examples of the extended technique are presented for the case of microwave reflection from the upper hybrid resonance layer in a tokamak plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Spectroscopic study of z-pinch stagnation on Z.

Fast z-pinches provide intense 1-10 keV photon energy radiation sources. Here, we analyze time-, space-, and spectrally-resolved {approx}2 keV K-shell emissions from Al (5% Mg) wire array implosions on Sandia's Z machine pulsed power driver. The stagnating plasma is modeled as three separate radial zones, and collisional-radiative modeling with radiation transport calculations are used to constrain the temperatures and densities in these regions, accounting for K-shell line opacity and Doppler effects. We discuss plasma conditions and dynamics at the onset of stagnation, and compare inferences from the atomic modeling to three-dimensional magneto-hydrodynamic simulations.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Ideal hydrodynamic scaling relations for a stagnated imploding spherical plasma liner formed by an array of merging plasma jets

This work presents scaling relations for the peak thermal pressure and stagnation time (over which peak pressure is sustained) for an imploding spherical plasma liner formed by an array of merging plasma jets. Results were derived from three-dimensional (3D) ideal hydrodynamic simulation results obtained using the smoothed particle hydrodynamics code SPHC. The 3D results were compared to equivalent one-dimensional (1D) simulation results. It is found that peak thermal pressure scales linearly with the number of jets and initial jet density and Mach number, quadratically with initial jet radius and velocity, and inversely with the initial jet length and the square of the chamber wall radius. The stagnation time scales approximately as the initial jet length divided by the initial jet velocity. Differences between the 3D and 1D results are attributed to the inclusion of thermal transport, ionization, and perfect symmetry in the 1D simulations. A subset of the results reported here formed the initial design basis for the Plasma Liner Experiment [S. C. Hsu et al., Phys. Plasmas 19, 123514 (2012)].

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Diagnosing low-mode (ℓ < 6) and mid-mode (6 ≤ ℓ ≤ 60) asymmetries in the post-stagnation phase of laser-direct-drive deuterium–tritium cryogenic implosions on OMEGA

Low- and mid-mode perturbations are possible candidates for performance limitations in cryogenic direct-drive implosions on the OMEGA laser at the Laboratory of Laser Energetics. Simulations with a 3D hydrocode demonstrated that hotspot imagers do not show evidence of the shell breakup in the dense fuel. However, these same simulations revealed that the low- and mid-mode perturbations in the dense fuel could be diagnosed more easily in the post-stagnation phase of the implosion by analyzing the peak in the x-ray emission limb at the coronal–fuel interface than before or at the stagnation phase. In experiments, the asymmetries are inferred from gated images of the x-ray emission of the implosion by using a 16-pinhole array imager filtered to record x-ray energies >800 eV and an x-ray framing camera with 40-ps time integration and 20-μm spatial resolution. Furthermore, a modal analysis is applied to the spatial distribution of the x-ray emission from deuterium and tritium cryogenic implosions on OMEGA recorded after the bang time to diagnose the low- and mid-mode asymmetries, and to study the effect that the beam-to-target ratio (Rb/Rt) has on the shell integrity.

47 OTHER INSTRUMENTATION↗

Asymptotic scaling laws for the stagnation conditions of Z-pinch implosions

Implosions of magnetically driven annular shells (Z pinches) are studied in the laboratory to produce high-energy-density plasmas. Such plasmas have a wide-range of applications including x-ray generation, controlled thermonuclear fusion, and astrophysics studies. In this work, we theoretically investigate the in-flight dynamics of a magnetically driven, imploding cylindrical shell that stagnates onto itself upon collision on axis. The converging flow of the Z-pinch is analyzed by considering the implosion trajectory in the (A, M) parametric plane, where A is the in-flight aspect ratio and M is the implosion Mach number. For an ideal implosion in the absence of instabilities and in the limit of A ≫ 1, we derive asymptotic scaling laws for hydrodynamic quantities evaluated at stagnation (e.g., density, temperature, and pressure) and for performance metrics (e.g., soft x-ray emission, K-shell x-ray emission, and neutron yield) as functions of target-design parameters.

Ruiz, D. E. [Sandia National Laboratories (SNL-NM)↗

Hydrodynamic-dissipation relation for characterizing flow stagnation

Hydrodynamic stagnation converts flow energy into internal energy. Here we develop a technique to directly analyze this hydrodynamic-dissipation process, which also yields a lengthscale associated with the conversion of flow energy to internal energy. We demonstrate the usefulness of this analysis for finding and comparing the hydrodynamic-stagnation dynamics of implosions theoretically, and in a test application to Z-pinch implosion data.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Turbulent stagnation in a Z -pinch plasma

The ion kinetic energy in a stagnating plasma was previously determined by Kroupp et al. [Phys. Rev. Lett.107, 105001 (2011)] from Doppler-dominated line shapes augmented by measurements of plasma properties and assuming a uniform-plasma model. Notably, the energy was found to be dominantly stored in hydrodynamic flow. Here we advance a new description of this stagnation as supersonically turbulent. Such turbulence implies a nonuniform density distribution. Here, we demonstrate how to reanalyze the spectroscopic data consistent with the turbulent picture and show that this leads to better concordance of the overconstrained spectroscopic measurements, while also substantially lowering the inferred mean density.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A stagnation pressure probe for use in supersonic flow

Probe was developed which is capable of recording true stagnation pressure in supersonic and subsonic flows. Static pressure orifices in the compression surface allow probe to be used as combined flow direction and stagnation pressure sensor.

Goodyer, M. J.↗

Combustion of a premixed system in stagnation flow. I - Theoretical.

The theoretical steady-state and transient characteristics of a premixed combustible system in laminar axisymmetric stagnation flow are studied by way of numerical solution of the governing boundary-layer equations. Computations, which are based on the oxidation reaction of carbon monoxide in humid air, invoke a minimum of simplifying assumptions. Steady-state results include prediction of (1) profiles of the state variables, (2) extinction of blow-off conditions, (3) ignition conditions, and (4) the heat flux to the stagnation point. Computer simulations of the unsteady state provide an indication of the stability of a given steady state to perturbations. Comparisons between some of the predictions of the mathematical model and the results of laboratory experiments will be reported in Part II.

Smith, H. W.↗