Search NASA⌕ Search

SEARCH · Search NASA

Results for “STATIC FRICTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1998

Evaluation of Advanced Solid Lubricant Coatings for Foil Air Bearings Operating at 25 and 500 C

The tribological properties of one chrome oxide and one chrome carbide based solid lubricant coating were evaluated in a partial-arc foil bearing at 25 and 500 C. Start/stop bearing operation up to 20,000 cycles were run under 10 kPa (1.5 psi) static deadweight load. Bearing friction (torque) was measured during the test. Specimen wear and SEM/EDS surface analyses were conducted after testing to understand and elucidate the tribological characteristics observed. The chrome oxide coating which contains both (Ag) and (BaF2/CaF2) for low and high temperature lubrication, exhibited low friction in sliding against Al2O3 coated foils at 25 and 500 C. The chrome carbide coating, which lacked a low temperature lubricant but contained BaF2/CaF2 as a high temperature lubricant, exhibited high friction at 25 C and low friction at 500 C against both bare and Al2O3 coated superalloy foil surfaces. Post test surface analyses suggest that improved tribological performance is exhibited when a lubricant film from the coating transfers to the foil surface.

DellaCorte, Christopher↗
NASA NTRS2003

Study of Unsteady Flows with Concave Wall Effect

This paper presents computational fluid dynamic studies of the inlet turbulence and wall curvature effects on the flow steadiness at near wall surface locations in boundary layer flows. The time-stepping RANS numerical solver of the NASA Glenn-HT RANS code and a one-equation turbulence model, with a uniform inlet turbulence modeling level of the order of 10 percent of molecular viscosity, were used to perform the numerical computations. The approach was first calibrated for its predictabilities of friction factor, velocity, and temperature at near surface locations within a transitional boundary layer over concave wall. The approach was then used to predict the velocity and friction factor variations in a boundary layer recovering from concave curvature. As time iteration proceeded in the computations, the computed friction factors converged to their values from existing experiments. The computed friction factors, velocity, and static temperatures at near wall surface locations oscillated periodically in terms of time iteration steps and physical locations along the span-wise direction. At the upstream stations, the relationship among the normal and tangential velocities showed vortices effects on the velocity variations. Coherent vortices effect on the velocity components broke down at downstream stations. The computations also predicted the vortices effects on the velocity variations within a boundary layer flow developed along a concave wall surface with a downstream recovery flat wall surface. It was concluded that the computational approach might have the potential to analyze the flow steadiness in a turbine blade flow.

Wang, Chi R.↗
NASA NTRS1984

O(+) acceleration due to resistive momentum transfer in the auroral field line plasma

An analytical model is defined to demonstrate that parallel acceleration of an O(+) ion beam in the ionosphere can occur naturally due to the presence of a quasi-static parallel electric field. Momentum equations are defined for friction between hydrogen ions and electrons, which produces a quasi-static electric field. The field can accelerate ions, e.g., the O(+) ions, which do not participate in the frictional momentum exchange. The conditions are shown to be applicable to the auroral field line plasma if a current is present along the magnetic field. A simulation performed with the equations shows that the field line plasma exhibits dynamic behavior after a field-aligned current appears. The resulting momentum gain by O(+) ions can be sufficient for causing a potential drop of several kilovolts along the field line.

Mitchell, H. G., Jr.↗
NASA NTRS1976

Analytical comparison of effects of solid-friction and viscous structural damping on panel flutter

A Galerkin modal analysis is presented that accounts for the effects of both solid friction and viscous structural damping on panel flutter, based on unsteady aerodynamic forces from supersonic potential flow. The eigensolutions are made by complex eigenvalue computer routines. Markedly different effects on the flutter boundary of the two types of structural damping are obtained. This result establishes that there is not, in general, an "equivalent viscous" damping for solid-friction damping. For the limiting case of the static-aerodynamic approximation, a substantially different flutter dynamic pressure is obtained for solid friction identically zero compared with solid friction approaching zero as a limit. Use of the quasi-static aerodynamic approximation eliminates that difference.

Cunningham, H. J.↗
NASA NTRS1982

Flight, Wind Tunnel, and Numerical Experiments with a Slender Cone at Incidence

The three-dimensional leeward separation about a 5-deg semi-angle cone of 11 deg angle of incidence was Investigated in night, in the wind tunnel, and by numerical computations. The test conditions were Mach numbers of 0.6, 1.5, and 1.8 at Reynolds numbers between 7 and 10 million based on freestream conditions and a 76.2-cm (30-in.) length of surface. The surface pressure conditions measured included those of fluctuating and mean static, as well as recovery pressures generated by obstacle blocks to provide skin friction and separation-line locations. The mean static pressures from flight and wind tunnel were in reasonably good agreement. The computed results gave the same distributions, but were slightly more positive in magnitude. The experimentally measured primary and secondary separation line locations compared closely with computed results. There were substantial differences In level between the surface root-mean-square pressure fluctuations obtained in night and in the wind tunnel, due, It Is thought, to a relatively high acoustic disturbance level in the tunnel compared with the quiescent atmospheric conditions in night.

Peake, David J.↗
NASA NTRS1973

Oxygen and sulfur interactions with a clean iron surface and the effect of rubbing contact on these interactions

The interaction of sulfur and oxygen with an iron surface was studied with Auger spectroscopy analysis both statically and during sliding-friction experiments in a vacuum environment. Oxygen, hydrogen sulfide, methyl mercaptan, and sulfur dioxide were adsorbed to an iron surface. Results indicate that sulfide films formed on clean iron surfaces are completely displaced by oxygen. Hydrocarbons containing sulfur, such as methyl mercaptan, adsorb dissociatively. Less sulfur is adsorbed during sliding with hydrogen sulfide and methyl mercaptan than in the absence of sliding. With both oxygen and sulfur dioxide, sliding did not affect the amount of material adsorbed to iron.

Buckley, D. H.↗
NASA NTRS1973

Auger analysis of oxygen and sulfur interactions with various metals and the effect of sliding on these interactions

Various gases were adsorbed to copper, aluminum, and chromium surfaces. The gases included oxygen, hydrogen sulfide, methyl mercaptan, and sulfur dioxide. Chemisorption was conducted on static surfaces and during dynamic friction experiments. An Auger cyclindrical mirror analyzer was used to monitor surface films. The sulfur containing gases adsorbed readily to all surfaces. Exposures of as little as 0.000001 (torr)(sec) (1 langmuir) were sufficient to reduce friction. Sliding contact did not affect chemisorption of copper or aluminum but did affect chemisorption to chromium surfaces. Oxygen removed sulfur films from all surfaces at room temperature (23 C). Gaseous exposures were from 0.000001 to 0.01 (torr)(sec) (1 to 10,000 langmuirs).

Buckley, D. H.↗
NASA NTRS1976

An experimental and computational investigation of the flow field about a transonic airfoil in supercritical flow with turbulent boundary-layer separation

A combined experimental and computational research program is described for testing and guiding turbulence modeling within regions of separation induced by shock waves incident in turbulent boundary layers. Specifically, studies are made of the separated flow the rear portion of an 18%-thick circular-arc airfoil at zero angle of attack in high Reynolds number supercritical flow. The measurements include distributions of surface static pressure and local skin friction. The instruments employed include highfrequency response pressure cells and a large array of surface hot-wire skin-friction gages. Computations at the experimental flow conditions are made using time-dependent solutions of ensemble-averaged Navier-Stokes equations, plus additional equations for the turbulence modeling.

Rubesin, M. W.↗
NASA NTRS1976

An experimental and computational investigation of the flow field about a transonic airfoil in supercritical flow with turbulent boundary-layer separation

A combined experimental and computational research program for testing and guiding turbulence modeling within regions of separation induced by shock waves incident on turbulent boundary layers is described. Specifically, studies are made of the separated flow over the rear portion of an 18%-thick circular-arc airfoil at zero angle of attack in high Reynolds number supercritical flow. The measurements include distributions of surface static pressure and local skin friction. The instruments employed include high-frequency response pressure cells and a large array of surface hot-wire skin-friction gages. Computations at the experimental flow conditions are made using time-dependent solutions of ensemble-averaged Navier-Stokes equations, plus additional equations for the turbulence modeling.

Rubesin, M. W.↗
NASA NTRS1976

Effect of geometry modifications on effectiveness of slot injection in hypersonic flow

The study presents wind-tunnel measurements of surface static pressures, equilibrium temperatures, and skin friction downstream of tangential slot injection into a thick turbulent hypersonic boundary layer from two modified slot configurations. The data are compared with results obtained for baseline configurations reported by Cary and Hefner (1970, 1972) to determine whether simple modifications to the slot configuration can produce improved cooling effectiveness and skin friction reduction. The baseline slot configurations are simply modified by thickening the slot lip and by elevating the location of the slot exit above the flat plate. Although the results indicate that simple modifications of the baseline slot configurations can enhance the skin friction reductions obtained with tangential slot injection, slot base drag estimates show that neither of the modifications will lessen the impact of the systems penalties for collecting, ducting, and injecting the slot air.

Hefner, J. N.↗
NASA NTRS1989

The effect of asymmetric vortex wake characteristics on a slender delta wing undergoing wing rock motion

An experimental investigation into the fluid mechanisms responsible for wing rock on a slender delta wing with 80 deg leading edge sweep has been conducted. Time history and flow visualization data are presented for a wide angle-of-attack range. The use of an air bearing spindle has allowed the motion of the wing to be free from bearing friction or mechanical hysteresis. A bistable static condition has been found in vortex breakdown at an angle of attack of 40 deg which causes an overshoot of the steady state rocking amplitude. Flow visualization experiments also reveal a difference in static and dynamic breakdown locations on the wing. A hysteresis loop in dynamic breakdown location similar to that seen on pitching delta wings was observed as the wing was undergoing the limit cycle oscillation.

Arena, A. S., Jr.↗
NASA NTRS1993

Geometry control in prestressed adaptive space trusses

In this work the actuator placement problem for the precision control in prestressed adaptive space trusses is studied. These structures cannot be statically determinate, implying that the length-adjusting actuators have to work against the existing prestressing forces, and also against the stresses caused by the actuation. This type of difficulties does not exist in statically determinate adaptive trusses where, except for overcoming the friction, the actuators operate under zero axial force, and require almost no energy. The actuator placement problem in statically inderterminate trusses is, therefore, governed seriously by the energy and the strength requirements. The paper provides various methodologies for the actuator placement problem in prestressed space trusses.

Sener, Murat↗
NASA NTRS2006

High-Strain-Rate Compression Testing of Ice

In the present study a modified split Hopkinson pressure bar (SHPB) was employed to study the effect of strain rate on the dynamic material response of ice. Disk-shaped ice specimens with flat, parallel end faces were either provided by Dartmouth College (Hanover, NH) or grown at Case Western Reserve University (Cleveland, OH). The SHPB was adapted to perform tests at high strain rates in the range 60 to 1400/s at test temperatures of -10 and -30 C. Experimental results showed that the strength of ice increases with increasing strain rates and this occurs over a change in strain rate of five orders of magnitude. Under these strain rate conditions the ice microstructure has a slight influence on the strength, but it is much less than the influence it has under quasi-static loading conditions. End constraint and frictional effects do not influence the compression tests like they do at slower strain rates, and therefore the diameter/thickness ratio of the samples is not as critical. The strength of ice at high strain rates was found to increase with decreasing test temperatures. Ice has been identified as a potential source of debris to impact the shuttle; data presented in this report can be used to validate and/or develop material models for ice impact analyses for shuttle Return to Flight efforts.

Shazly, Mostafa↗
NASA NTRS1944

A Theoretical Investigation of Longitudinal Stability of Airplanes with Free Controls Including Effect of Friction in Control System

The relation between the elevator hinge moment parameters and the control forces for changes in forward speed and in maneuvers is shown for several values of static stability and elevator mass balance. The stability of the short period oscillations is shown as a series of boundaries giving the limits of the stable regions in terms of the elevator hinge moment parameters. The effects of static stability, elevator moment of inertia, elevator mass unbalance, and airplane density are also considered. Dynamic instability is likely to occur if there is mass unbalance of the elevator control system combined with a small restoring tendency (high aerodynamic balance). This instability can be prevented by a rearrangement of the unbalancing weights which, however, involves an increase of the amount of weight necessary. It can also be prevented by the addition of viscous friction to the elevator control system provided the airplane center of gravity is not behind a certain critical position. For high values of the density parameter, which correspond to high altitudes of flight, the addition of moderate amounts of viscous friction may be destabilizing even when the airplane is statically stable. In this case, increasing the viscous friction makes the oscillation stable again. The condition in which viscous friction causes dynamic instability of a statically stable airplane is limited to a definite range of hinge moment parameters. It is shown that, when viscous friction causes increasing oscillations, solid friction will produce steady oscillations having an amplitude proportional to the amount of friction.

Greenberg, Harry↗
NASA NTRS1991

Dynamic measurements of gear tooth friction and load

As part of a program to study fundamental mechanisms of gear noise, static and dynamic gear tooth strain measurements were made on the NASA gear-noise rig. Tooth-fillet strains from low-contact ratio-spur gears were recorded for 28 operating conditions. A method is introduced whereby strain gage measurements taken from both the tension and compression sides of a gear tooth can be transformed into the normal and frictional loads on the tooth. This technique was applied to both the static and dynamic strain data. The static case results showed close agreement with expected results. For the dynamic case, the normal-force computation produced very good results, but the friction results, although promising, were not as accurate. Tooth sliding friction strongly affected the signal from the strain gage on the tensionside of the tooth. The compression gage was affected by friction to a much lesser degree. The potential of the method to measure friction force was demonstrated, but further refinement will be required before this technique can be used to measure friction forces dynamically with an acceptable degree of accuracy.

Rebbechi, Brian↗
NASA NTRS1977

Analysis of the separated boundary layer flow on the surface and in the wake of blunt trailing edge airfoils

The viscous flow phenomena associated with sharp and blunt trailing edge airfoils were investigated. Experimental measurements were obtained for a 17 percent thick, high performance GAW-1 airfoil. Experimental measurements consist of velocity and static pressure profiles which were obtained by the use of forward and reverse total pressure probes and disc type static pressure probes over the surface and in the wake of sharp and blunt trailing edge airfoils. Measurements of the upper surface boundary layer were obtained in both the attached and separated flow regions. In addition, static pressure data were acquired, and skin friction on the airfoil upper surface was measured with a specially constructed device. Comparison of the viscous flow data with data previously obtained elsewhere indicates reasonable agreement in the attached flow region. In the separated flow region, considerable differences exist between these two sets of measurements.

Goradia, S. H.↗
NASA NTRS1984

Effects of the oceans on polar motion: Continued investigations

Data on the pole tide, the oceanic response to the Chandler wobble were presented. Observed North Sea pole tide enhancement (i.e., larger amplitudes than a static tide would possess) resulted from bottom friction, with the drag coefficient, in combination with the depth of the North Sea decreasing southward. Computer programs were written for the boundary conditions. Dissipation of the energy by North Sea pole tide currents was also computed; preliminary results indicate that such dissipation may explain a significant fraction of Chandler wobble energy loss.

Dickman, S. R.↗
NASA NTRS1984

Thermal tides in the atmosphere of Venus - Comparison of model results with observations

A linearized primitive equation model adapted to Venusian conditions was used to study thermal tidal anomalies in the Venus atmosphere exposed by Venus Orbiter IR sensors. The model received as input the IR data, mean zonal wind and solar input as functions of height and latitude, and the global mean static stability and Newtonian cooling and Rayleigh friction in relation to altitude. Basic state and forcing functions were defined for Venus, and the model generated brightness temperatures which could be compared with the IR data. The good correlations obtained suggest that the model accurately accounts for the low variation of phase with altitude and stronger semidiurnal oscillation features than diurnal oscillations. The model is concluded as a useful tool for assessing the role of thermal tides in maintaining Venus super rotation.

Pechmann, J. B.↗