Search NASA⌕ Search

SEARCH · Search NASA

Results for “STATIC LOADING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1933

Dynamic Breaking Tests of Airplane Parts

The static stresses of airplane parts, the magnitude of which can be determined with the aid of static load assumptions, are mostly superposed by dynamic stresses, the magnitude of which has been but little explored. The object of the present investigation is to show how the strength of airplane parts can best be tested with respect to dynamic stresses with and without superposed static loading, and to what extent the dynamic strength of the parts depends on their structural design. Experimental apparatus and evaluation methods were developed and tried for the execution of vibration-strength tests with entire structural parts both with and without superposed static loading. Altogether ten metal spars and spar pieces and two wooden spars were subjected to vibration breaking tests.

Hertel, Heinrich↗
NASA NTRS2012

Reducing Undue Conservatism in "Higher Frequency" Structural Design Loads in Aerospace Components

This study is intended to investigate the frequency dependency of significant strain due to vibratory loads in aerospace vehicle components. The notion that "higher frequency" dynamic loads applied as static loads is inherently conservative is perceived as widely accepted. This effort is focused on demonstrating that principle and attempting to evolve methods to capitalize on it to mitigate undue conservatism. It has been suggested that observations of higher frequency modes that resulted in very low corresponding strain did so due to those modes not being significant. Two avionics boxes, one with its first significant mode at 341 Hz and the other at 857 Hz, were attached to a flat panel installed on a curved orthogrid panel which was driven acoustically in tests performed at NASA/MSFC. Strain and acceleration were measured at select locations on each of the boxes. When possible, strain gage rosettes and accelerometers were installed on either side of a given structural member so that measured strain and acceleration data would directly correspond to one another. Ultimately, a frequency above which vibratory loads can be disregarded for purposes of static structural analyses and sizing of typical robust aerospace components is sought.

Knight, J. Brent↗
NASA NTRS1977

Characterization of crack growth under combined loading

Room-temperature static and cyclic tests were made on 21 aluminum plates in the shape of a 91.4x91.4-cm Maltese cross with 45 deg flaws to develop crack growth and fracture toughness data under mixed-mode conditions. During cyclic testing, it was impossible to maintain a high proportion of shear-mode deformation on the crack tips. Cracks either branched or turned. Under static loading, cracks remained straight if shear stress intensity exceeded normal stress intensity. Mixed-mode crack growth rate data compared reasonably well with published single-mode data, and measured crack displacements agreed with the straight and branched crack analyses. Values of critical strain energy release rate at fracture for pure shear were approximately 50% higher than for pure normal opening, and there was a large reduction in normal stress intensity at fracture in the presence of high shear stress intensity. Net section stresses were well into the inelastic range when fracture occurred under high shear on the cracks.

Feldman, A.↗
NASA NTRS1994

Structural design feasibility study of Space Station long spacer truss

The structural design and configuration feasibility of the long spacer truss assembly that will be used as part of the Space Station Freedom is the focus of this study. The structural analysis discussed herein is derived from the transient loading events presented in the Space Transportation System Interface Control Document (STS ICD). The transient loading events are liftoff, landing, and emergency landing loads. Quasi-static loading events were neglected in this study since the magnitude of the quasi-static acceleration factors is lower than that of the transient acceleration factors. Structural analysis of the proposed configuration of the long spacer truss with four longerons indicated that negative safety margins are possible. As a result, configuration changes were proposed. The primary configuration change suggested was to increase the number of truss longerons to six. The six-longeron truss appears to be a more promising structure than the four-longeron truss because it offers a positive margin of safety and more volume in its second bay (BAY2). This additional volume can be used for resupply of some of the orbital replacement units (such as a battery box). Note that the design effort on the long spacer truss has not fully begun and that calculations and reports of the negative safety margins are, to date, based on concept only.

Armand, Sasan C.↗
NASA NTRS1978

FASOR - A second generation shell of revolution code

An integrated computer program entitled Field Analysis of Shells of Revolution (FASOR) currently under development for NASA is described. When completed, this code will treat prebuckling, buckling, initial postbuckling and vibrations under axisymmetric static loads as well as linear response and bifurcation under asymmetric static loads. Although these modes of response are treated by existing programs, FASOR extends the class of problems treated to include general anisotropy and transverse shear deformations of stiffened laminated shells. At the same time, a primary goal is to develop a program which is free of the usual problems of modeling, numerical convergence and ill-conditioning, laborious problem setup, limitations on problem size and interpretation of output. The field method is briefly described, the shell differential equations are cast in a suitable form for solution by this method and essential aspects of the input format are presented. Numerical results are given for both unstiffened and stiffened anisotropic cylindrical shells and compared with previously published analytical solutions.

Cohen, G. A.↗
NASA NTRS1989

The durability of graphite/epoxy laminate subjected to repeated low velocity impact

Low velocity impact has been considered as quasi-static loading, as the dynamic effects are decaying before the pressure reaches its maximum. However, when the impact energy is low enough as not to cause visible damage, the dynamic effect at the beginning of the impact may cause internal damage to the laminate. Laminates were loaded quasi-statically and by impact to the same bending strain and with the same indenter shape several times. The laminates that were subjected to the impact loading failed much more rapidly. Analysis of the problem shows that the stress waves created by the impact at the beginning of contact intensify the damage zone created by the preceding impact until the final failure occurs.

Rotem, A.↗
NASA NTRS1992

Stiffness of magnetic bearings subjected to combined static and dynamic loads

This paper investigates the stiffness of a magnetic bearing that is subjected to the combined action of static and dynamic loads. Since their sum cannot exceed the saturation load, a large static load will imply that the bearing can carry only a small dynamic load. This smaller dynamic load together with the practical vibration amplitude define a practical upper bound to the dynamic stiffness. This paper also presents approximate design formulas and curves for this stiffness capacity as a function of the ratio of dynamic and static loads. In addition, it indicates that vibrations larger than a certain gap fraction can destabilize the magnetic bearing. This gap fraction, called the critical gap fraction, depends on the dynamic and static load ratio. For example, if the dynamic load is half of the static load, the use of more than 25 percent of gap can destabilize the bearing.

Rao, D. K.↗
NASA NTRS1974

Bonded composite to metal scarf joint performance in an aircraft landing gear drag strut

The structural performance of a boron-epoxy reinforced titanium drag strut, which contains a bonded scarf joint and was designed to the criteria of the Boeing 747 transport, was evaluated. An experimental and analytical investigation was conducted. The strut was exposed to two lifetimes of spectrum loading and was statically loaded to the tensile and compressive design ultimate loads. Throughout the test program no evidence of any damage in the drag strut was detected by strain gage measurements, ultrasonic inspection, or visual observation. An analytical study of the bonded joint was made using the NASA structural analysis computer program NASTRAN. A comparison of the strains predicted by the NASTRAN computer program with the experimentally determined values shows excellent agreement. The NASTRAN computer program is a viable tool for studying, in detail, the stresses and strains induced in a bonded joint.

Howell, W. E.↗
NASA NTRS1976

Boron-epoxy-reinforced titanium aircraft landing-gear drag strut

The structural performance of a boron-epoxy-reinforced titanium drag strut, containing a bonded scarf joint and designed to the criteria of a large commercial transport, has been evaluated experimentally and analytically. The strut was exposed to two lifetimes of fatigue loading and was statically loaded to the tensile and compressive design ultimate loads. Throughout the test program no evidence of any damage in the drag strut was detected by strain-gage measurements, ultrasonic inspection, or visual observation. The bonded joint was analyzed using the NASTRAN computer program. A comparison of the strains predicted by the NASTRAN computer program with the experimentally determined values shows excellent agreement. An analytical study indicated that the nonlinear behavior of a structural spacer at each end of the strut could be explained by the inelastic behavior and possible creep of the adhesive.

Howell, W. E.↗
NASA NTRSDate not supplied

Mass Mitigation in Structural Designs Via Dynamic Properties

The efforts reported here are focused on mitigating unnecessary mass in aerospace hardware. The approach to remove this undesired mass from the design is to leverage both the dynamic strength of materials and the frequency dependency of strain. Analytically predicted dynamic responses of structures are often applied as static loads in stress analyses that ultimately dictate the weight of a structural design. Assuming a dynamic response is a static load and then comparing resulting stress predictions to a static strength property is a long-standing engineering practice. Doing so is known to be, or is assumed to be, conservative. However, little indication of the order of magnitude of embedded conservatism has been identified. NASA/MSFC efforts in 2011, 2019, 2020, and now in 2021 have begun to qualitatively show the order of magnitude of that conservatism. A quick turnaround engineering method is pursued to leverage the subject facets of physics for the purpose of decreasing the weight of flight hardware. Tests performed using simple beams and significant observations are described.

conservative design loads↗
NASA NTRSDate not supplied

Mass Mitigation in Structural Designs Via Dynamic Properties

Mass Mitigation in Structural Designs Via Dynamic Properties The reported efforts are focused on mitigating unnecessary mass in aerospace hardware via leveraging dynamic strength of materials and the frequency dependency of strain. Analytically predicted dynamic responses of structures are often applied as static loads in stress analyses that ultimately dictate the weight of a structural design. Assuming a dynamic response is a static load and then comparing resulting stress predictions to a static strength property is a long-standing engineering practice. Doing so is known to be, or is assumed to be, conservative. However, little indication of the order of magnitude of embedded conservatism has been identified. NASA/MSFC efforts in 2011, 2019, 2020, and now in 2021 have begun to qualitatively show the order of magnitude of that conservatism. A quick turnaround engineering method is pursued to leverage the subject facets of physics for the purpose of decreasing the weight of flight hardware. Tests performed using simple beams and significant observations are described.

mass mitigation↗
NASA NTRS1961

Comparison of Experimental and Theoretical Static Aeroelastic Loads and Deflections of a Thin 45 deg Delta Wing in Supersonic Flow

Wind tunnel tests showing the effects of static aeroelasticity for a thin 45 degree delta wing in supersonic flow are presented and compared with theory in the Mach number range 1.30 t o 4.00. Calculated deformations, normal-force coefficients, and pitching-moment coefficients based on a linearized potential theory for subsonic leading edges at a Mach number of 1.30 and a linearized potential theory for supersonic leading edges at Mach numbers of 1.64, 3.00, and 4.00 are shown to compare favorably with the wind-tunnel results. Calculations of these same deformations and coefficients based on piston theory are shown to compare satisfactorily with experiment at a Mach number of 4.00 but not so well at a Mach number of 3.00. A factor modification of piston theory is suggested which improves the correlation of these results with experiment and also with the potential-theory results.

Bennett, Floyd V.↗
NASA NTRS1997

Quasi-Static Viscoelasticity Loading Measurements of an Aircraft Tire

Stair-step loading, cyclic loading, and long-term relaxation tests were performed on an aircraft tire to observe the quasi-static viscoelastic response of the tire. The data indicate that the tire continues to respond viscoelastically even after it has been softened by deformation. Load relaxation data from the stair-step test at the 15,000-lb loading was fit to a monotonically decreasing Prony series.

Mason, Angela J.↗
NASA NTRS1985

Sensitivity derivatives for static test loading boundary conditions

Attention is given to the application of the adjoint variable method under the special combination of displacement and stress boundary conditions which occur when static test conditions are simulated. In the two-step problem-solving method employed, calculation of internal stresses, displacements and total reaction force at the boundary is followed by the calculation of the applied load and the total reaction force due to unit displacements.

Gurdal, Z.↗
NASA NTRS1989

Simplified procedures for designing adhesively bonded composite joints

Procedures for the preliminary design of composite adhesive joints are described. Typical joints, their respective free body diagrams, and approximate equations for estimating the stresses in each of these typical joints are summarized. Equations are also presented to check the critical conditions of the joint such as minimum length, maximum adhesive shear stress, and peel-off stress. To illustrate the procedure, sample designs are described in step-by-step fashion for a butt joint with single doubler subjected to static loads, cyclic loads, and environmental effects. The results show that unsymmetric adhesive joints are inefficient and should be avoided, and hygrothermal environments and cyclic loads dramatically reduce the structural integrity of the joint and require several joint lengths compared with those for static load with no environmental effects.

Chamis, C. C.↗